Measurement Sensors

Filters

In stock (386)
Out of stock (658)

Showing 553 - 576 of 719 products

$0.00

Sold Out

Specifications

Model		SI-F10U
Type		Long distance type Spectrum unit
Measurement range		11.3 to 12.35 mm 0.44" to 0.49" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø40 µm ø0.001575"^*3
Linearity		±0.3 µm ±0.000012" ^*4
Resolution		0.01 µm ^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	-
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F01U3 Keyence

$0.00

Sold Out

Specifications

Model		SI-F01U3
Measurement range		0.05 to 1.1 mm 0.002 to 0.04" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 650 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F01U Keyence

$0.00

Sold Out

Specifications

Model		SI-F01U
Type		Micro-head type Spectrum unit
Measurement range		0.05 to 1.1 mm 0.002 to 0.04" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.2 µm ±0.000008" ^*4
Resolution		0.001 µm ^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	-
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-FA103 Keyence

$0.00

Sold Out

Specifications

Model			SI-FA103
Separate type
Type			Expansion controller^*1
No. of connectable spectrum units			1
Display	Minimum display unit		N/A
	Display range
	Display cycle
Terminal block	Laser remote interlock input		N/A^*2
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 1 outputs, Output impedance: 100 Ω^*2
	Analog current output		4 to 20 mA x 1 output, Maximum load resistance: 350 Ω^*2
	Alarm output		N/A^*2
	General comparator output
Expansion connector	TIMING2 input
	RESET input
	Auto-zero input
	Program switch input
	Alarm output
	Comparator/ binary output	Binary output
		Strobe output
		Binary selection output
		Binary selection input
RS-232C interface			N/A
USB interface
Ethernet interface
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*3
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 300 g
^1 Up to four expansion controllers can be connected to the main controller. ^2 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^*3 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-FA100 Keyence

$0.00

Sold Out

Specifications

Model			SI-FA100^*1
Separate type			SI-FA100
Type			Expansion controller^*2
No. of connectable spectrum units			1
Display	Minimum display unit		N/A
	Display range
	Display cycle
Terminal block	Laser remote interlock input		N/A^*3
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 1 output, Output impedance: 100 Ω^*3
	Analog current output		4 to 20 mA x 1 output, Maximum load resistance: 350 Ω^*3
	Alarm output		N/A^*3
	General comparator output
Expansion connector	TIMING2 input
	RESET input
	Auto-zero input
	Program switch input
	Alarm output
	Comparator/ binary output	Binary output
		Strobe output
		Binary selection output
		Binary selection input
RS-232C interface			N/A
USB interface
Ethernet interface
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		Supplied from the main controller
	Current consumption
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*4
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 300 g
^1 The SI-F1003 can be used independently, The measured value display and setting change can be done with the display panel(SI-FD500) and setup support software(SI-H3). ^2 Up to four expansion controllers can be connected to the main controller. ^3 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^4 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-FD500 Keyence

$0.00

Sold Out

Specifications

Model			SI-FD500
Type			Main Controller Separate type^*1
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec.
Terminal block	Laser remote interlock input		Non-voltage input^*2
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*2
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*2
	Alarm output		NPN open-collector output (N.C.)^*2
	General comparator output		NPN open-collector output^*2
Expansion connector	TIMING2 input		Non-voltage input^*2
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*2
	Alarm output		NPN open-collector output (N.C.)^*2
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*2
		Strobe output	NPN open-collector output^*2
		Binary selection output
		Binary selection input	Non-voltage input^*2
RS-232C interface			Measured data output and control input/output (Baud rate selectable to 115,200 bps max.)
USB interface			USB 2.0 high speed compliant (USB 1.1 Full-SPEED compatible)
Ethernet interface			100Base-TX/10Base-T
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*3
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 The SI-F1001 can be used independently. The measured value display and setting change can be done with the display panel (SI-FD500) and setup support software (SI-H1). ^2 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^*3 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-F80 Keyence

$0.00

Sold Out

Specifications

Model		SI-F80
Type		Thickness measurement type Sensor head
Measurement range		0.05 to 1.1 mm 0.002" to 0.04" ^*1 (Possible detection distance : 80 to 81.1 mm 3.15" to 3.19")
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	IP64
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		SUS
Material	Sensor head
	Spectrum unit	Polycarbonate
Weight		Approx. 39 g (including cable)
^1 The thickness measurement type sensor head displays the measurement range for the distance between plates of glass. Ensure that the measurement target is within the possible detection distance range. ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained by measuring the gap between two glass plates with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F10 Keyence

$0.00

Sold Out

Specifications

Model		SI-F10
Type		Long distance type Sensor head
Measurement range		11.3 to 12.35 mm 0.44" to 0.49" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø40 µm ø0.001575"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	IP64
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +40 °C 32 to 104 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		SUS
Material	Sensor head
	Spectrum unit	Polycarbonate
Weight		Approx. 38 g (including cable)
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F01 Keyence

$0.00

Sold Out

Specifications

Model		SI-F01
Type		Micro-head type Sensor head
Measurement range		0.05 to 1.1 mm 0.002" to 0.04" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	IP67
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +85 °C 32 to 185 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		SUS
Material	Sensor head
	Spectrum unit	Polycarbonate
Weight		Approx. 24 g (including cable)
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F1003V Keyence

$0.00

Sold Out

Specifications

Model			SI-F1003V
Separate type			SI-F1003/SI-FD500
Type			Built-in main controller type
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec.
Terminal block	Laser remote interlock input		Non-voltage input^*1
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*1
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*1
	Alarm output		NPN open-collector output (N.C.)^*1
	General comparator output		NPN open-collector output^*1
Expansion connector	TIMING2 input		Non-voltage input^*1
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*1
	Alarm output		NPN open-collector output (N.C.)^*1
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*1
		Strobe output	NPN open-collector output^*1
		Binary selection output
		Binary selection input	Non-voltage input^*1
RS-232C interface			Measured data output and control input/output (Baud rate selectable to 115,200 bps max.)
USB interface			USB 2.0 high speed compliant (USB 1.1 Full-SPEED compatible)
Ethernet interface			100Base-TX/10Base-T
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*2
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^2 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-F1003 Keyence

$1,308.18

Only 2 units left

Specifications

Model			SI-F1003^*1
Type			Main Controller Separate type^*2
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec
Terminal block	Laser remote interlock input		Non-voltage or voltage input ^3.^4
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*4
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*4
	Alarm output		NPN open-collector output (N.C.)^*4
	General comparator output		NPN open-collector output ^5^4
Expansion connector	TIMING2 input		Non-voltage or voltage input ^3.^4
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*4
	Alarm output		NPN open-collector output (N.C.)^*4
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*4
		Strobe output	NPN open-collector output ^5^4
		Binary selection output
		Binary selection input	Non-voltage or voltage input ^3.^4
RS-232C interface			Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface			In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface			100BASE-TX/10BASE-T
Major functions			12 Out simultaneous measurementcalculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory,interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*6
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 The SI-F1003 can be used independently, The measured value display and setting change can be done with the display panel(SI-FD500) and setup support software(SI-H3). ^2 The SI-F1001 can be used independently. The measured value display and setting change can be done with the display panel (SI-FD500) and setup support software (SI-H1). ^3 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^4 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^5 The rating of the NPN open-collector: 50 mA max. (40 V max.), residual voltage of 0.5 V max. The rating of the PNP open collector: 50 mA max. (30 V max.), residual voltage of 0.5 V max. ^6 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-F1001V Keyence

$0.00

Sold Out

Specifications

Model			SI-F1001V
Separate type			SI-F1001/SI-FD500
Type			Built-in main controller type
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec.
Terminal block	Laser remote interlock input		Non-voltage input^*1
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*1
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*1
	Alarm output		NPN open-collector output (N.C.)^*1
	General comparator output		NPN open-collector output^*1
Expansion connector	TIMING2 input		Non-voltage input^*1
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*1
	Alarm output		NPN open-collector output (N.C.)^*1
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*1
		Strobe output	NPN open-collector output^*1
		Binary selection output
		Binary selection input	Non-voltage input^*1
RS-232C interface			Measured data output and control input/output (Baud rate selectable to 115,200 bps max.)
USB interface			USB 2.0 high speed compliant (USB 1.1 Full-SPEED compatible)
Ethernet interface			100Base-TX/10Base-T
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*2
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^2 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence SI-F1001 Keyence

$0.00

Sold Out

Specifications

Model			SI-F1001^*1
Type			Main Controller Separate type^*2
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec.
Terminal block	Laser remote interlock input		Non-voltage input^*3
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*3
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*3
	Alarm output		NPN open-collector output (N.C.)^*3
	General comparator output		NPN open-collector output^*3
Expansion connector	TIMING2 input		Non-voltage input^*3
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*3
	Alarm output		NPN open-collector output (N.C.)^*3
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*3
		Strobe output	NPN open-collector output^*3
		Binary selection output
		Binary selection input	Non-voltage input^*3
RS-232C interface			Measured data output and control input/output (Baud rate selectable to 115,200 bps max.)
USB interface			USB 2.0 high speed compliant (USB 1.1 Full-SPEED compatible)
Ethernet interface			100Base-TX/10Base-T
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*4
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 The SI-F1003 can be used independently, The measured value display and setting change can be done with the display panel(SI-FD500) and setup support software(SI-H3). ^2 The SI-F1001 can be used independently. The measured value display and setting change can be done with the display panel (SI-FD500) and setup support software (SI-H1). ^3 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^4 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence OP-87060 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87296 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87222 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence IB-30 Keyence

$797.58

Only 7 units left

Specifications

Model		IB-30
Light source	Wavelength	660 nm (Visible light semiconductor laser)
	Laser Class	Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10^*1)
Installation distance		0 to 300 mm 11.81"
Measurement range		30 mm 1.18"
Sampling cycle		12,500 times/sec. (80 µs)
Minimum detection target		ø0.2 mm ø0.01"^*2
Repeatability		10 µm 0.39 Mil^*3
Temperature characteristics		±0.1 % of F.S./°C (±30 µm 1.18 Mil)^*4
Operating indicators		Laser emission warning indicator: green LED
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux, Solar light: 10,000 lux
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Case	Galvanized die cast
	Lens cover	Glass
	Cable	PVC (2 m 6.6')
Weight		Approx. 510 g
^1 The classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 Value when measuring the target (white diffuse object) at the middle of the transmitter and receiver position, and at the center of the measurement range. ^3 When distance between transmitter and receiver is set to 300 mm 11.81", and light is half-shielded at a position 150 mm 5.91" from receiver. Deflection width (±2σ) when sampled for 30 seconds with an average number of times set to 64 times. ^4 When distance between transmitter and receiver is set to 100 mm 3.94" and full light is received.

Keyence IB-10 Keyence

$1,159.99

Only 9 units left

Specifications

Model		IB-10
Light source	Wavelength	660 nm (Visible light semiconductor laser)
	Laser Class	Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10^*1)
Installation distance		0 to 300 mm 11.81"
Measurement range		10 mm 0.39"
Sampling cycle		12,500 times/sec. (80 µs)
Minimum detection target		ø0.1 mm ø0.004"^*2
Repeatability		5 µm 0.20 Mil^*3
Temperature characteristics		±0.1 % of F.S./°C (±10 µm 0.39 Mil)^*4
Operating indicators		Laser emission warning indicator: green LED
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux, Solar light: 10,000 lux
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Case	Galvanized die cast
	Lens cover	Glass
	Cable	PVC (2 m 6.6')
Weight		Approx. 220 g
^1 The classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 Value when measuring the target (white diffuse object) at the middle of the transmitter and receiver position, and at the center of the measurement range. ^3 When distance between transmitter and receiver is set to 300 mm 11.81", and light is half-shielded at a position 150 mm 5.91" from receiver. Deflection width (±2σ) when sampled for 30 seconds with an average number of times set to 64 times. ^4 When distance between transmitter and receiver is set to 100 mm 3.94" and full light is received.

Keyence IB-05 Keyence

$1,607.79

Only 5 units left

Specifications

Model		IB-05
Light source	Wavelength	660 nm (Visible light semiconductor laser)
	Laser Class	Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10^*1)
Installation distance		0 to 300 mm 11.81"
Measurement range		5 mm 0.20"
Sampling cycle		12,500 times/sec. (80 µs)
Minimum detection target		ø0.05 mm ø0.002"^*2
Repeatability		5 µm 0.20 Mil^*3
Temperature characteristics		±0.1 % of F.S./°C (±5 µm 0.20 Mil)^*4
Operating indicators		Laser emission warning indicator: green LED
Environmental resistance	Ambient light	Incandescent lamp: 5,000 lux, Solar light: 5,000 lux
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Case	Galvanized die cast
	Lens cover	Glass
	Cable	PVC (2 m 6.6')
Weight		Approx. 180 g
^1 The classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 Value when measuring the target (white diffuse object) at the middle of the transmitter and receiver position, and at the center of the measurement range. ^3 When distance between transmitter and receiver is set to 300 mm 11.81", and light is half-shielded at a position 150 mm 5.91" from receiver. Deflection width (±2σ) when sampled for 30 seconds with an average number of times set to 64 times. ^4 When distance between transmitter and receiver is set to 100 mm 3.94" and full light is received.

Keyence IB-01 Keyence

$3,266.00

Only 1 unit left

Specifications

Model		IB-01
Light source	Wavelength	660 nm (Visible light semiconductor laser)
	Laser Class	Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10^*1)
Installation distance		0 to 2,000 mm 78.74"
Measurement range		ø1 mm ø0.04" (Installation distance 0 to 300 mm 11.81") ø1 to 2.5 mm (Installation distance 300 to 2,000 mm 11.81" to 78.74")
Sampling cycle		12,500 times/sec. (80 µs)
Minimum detection target		ø8 µm ø0.31 Mil (Installation distance 0 to 300 mm 11.81") ø8 to 50 µm ø0.31 to 1.97 Mil (Installation distance 300 to 2,000 mm 11.81" to 78.74")^*2
Repeatability		5 µm 0.20 Mil (distance 0 to 300 mm 11.81")^*3
Temperature characteristics		±0.2 % of F.S./°C^*4
Operating indicators		Laser emission warning indicator: green LED
Environmental resistance	Ambient light	Incandescent lamp: 5,000 lux, Solar light: 10,000 lux
	Ambient temperature	0 to +40 °C 32 to 104 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Case	PBT
	Lens cover	Glass
	Cable	PVC (2 m 6.6')
Weight		Approx. 140 g
^1 The classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 Value when measuring the target (white diffuse object) at the middle of the transmitter and receiver position, and at the center of the measurement range. ^3 When distance between transmitter and receiver is set to 300 mm 11.81", and light is half-shielded at a position 150 mm 5.91" from receiver. Deflection width (±2σ) when sampled for 30 seconds with an average number of times set to 64 times. ^4 When distance between transmitter and receiver is set to 100 mm 3.94" and full light is received.

Keyence IB-1550 Keyence

$0.00

Sold Out

Specifications

Model		IB-1550
Type		Panel mount
Main unit/Expansion unit		Expansion unit
Head compatibility		Yes
Display	Display resolution	0.01 %, 0.1 %, 1 % (switchable)
	Display range	–99.999 to 99.999, –99.99 to 99.99 –99.9 to 99.9, –99 to 99 (switchable)
	Digital display method	Dual7-segmentdisplay Upper level: 2-color (green/red) 5 digits Lower level: 5 green digits
	Operating indicators	Judgment indicator: 2-color (green/red) LED (HI, GO, LO) Bank indicator: Green LED x 4 Laser emission warning indicator: Green LED Others: Green LED x 8, red LED x 3
Analog output voltage		No
Analog current output
Control Input	Bank switch input, zero shift input	Non-voltage input ^*1
Control input	Zero shift input
	Laser emission stop input
	Timing input
	Reset input
	Adjust input
Control output	Judgment output (check output)	Open collector (NPN/PNP switchable, N.O./N.C. switchable) ^*2
Power supply	Power consumption	2550 mW or less (at 30 V, 85 mA max.) ^3 ^4 (including analog current output)
	Power voltage	Supplied from main unit ^*3
Environmental resistance	Pollution degree	2
	Ambient temperature	-10 to +50 °C (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, compound amplitude 1.5 mm, 2 hours each for X, Y, Z axes
Material		Main unit case/Front panel: polycarbonate, keytop: polyacetal, cable: PVC
Weight		Approx. 165 g (including accessories)
^1 The four external input wires are assigned with desired inputs. Rated no-voltage input: ON voltage 2 V or less, OFF current 0.05 mA or less Rated voltage input: Max. input rating 30 V or less, ON voltage 7.5 V or more, OFF current 0.05 mA or less ^2 Rated NPN open collector output: Max. 100 mA/ch (20 mA/ch when expansion units are connected), 30 V or less, residual voltage 1 V or less Rated PNP open collector output: Max. 50 mA/ch (20 mA/ch when expansion units are connected), power voltage or less, residual voltage 2 V or less ^3 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^4 Does not include the power consumption of the load. The power consumption with expansion units installed is the total of each amplifier unit’s power consumption. Example: When using one main unit (IB-1000) with two expansion units (IB-1050) (2400 mW X 1) + (2400 mW X 2) = 7200 mW

Keyence IB-1500 Keyence

$1,969.83

Only 7 units left

Specifications

Model		IB-1500
Type		Panel mount
Main unit/Expansion unit		Main unit
Head compatibility		Yes
Display	Display resolution	0.01 %, 0.1 %, 1 % (switchable)
	Display range	–99.999 to 99.999, –99.99 to 99.99 –99.9 to 99.9, –99 to 99 (switchable)
	Digital display method	Dual7-segmentdisplay Upper level: 2-color (green/red) 5 digits Lower level: 5 green digits
	Operating indicators	Judgment indicator: 2-color (green/red) LED (HI, GO, LO) Bank indicator: Green LED x 4 Laser emission warning indicator: Green LED Others: Green LED x 8, red LED x 3
Analog output voltage		±5 V, 1 to 5 V, 0 to 5 V Output impedance 100 Ω ^*1
Analog current output		4 to 20 mA Maximum load resistance 350 Ω ^*1
Control Input	Bank switch input, zero shift input	Non-voltage input ^*2
Control input	Zero shift input
	Laser emission stop input
	Timing input
	Reset input
	Adjust input
Control output	Judgment output (check output)	Open collector (NPN/PNP switchable, N.O./N.C. switchable) ^*3
Power supply	Power consumption	2550 mW or less (at 30 V, 85 mA max.) ^4 ^5 (including analog current output)
	Power voltage	10 to 30 VDC, including ripple (P-P) 10% Class 2 or LPS ^*4
Environmental resistance	Pollution degree	2
	Ambient temperature	-10 to +50 °C (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, compound amplitude 1.5 mm, 2 hours each for X, Y, Z axes
Material		Main unit case/Front panel: polycarbonate, keytop: polyacetal, cable: PVC
Weight		Approx. 170 g (including accessories)
^1 ±5 V, 1 to 5 V, 0 to 5 V, or 4 - 20 mA should be selected. ^2 The four external input wires are assigned with desired inputs. Rated no-voltage input: ON voltage 2 V or less, OFF current 0.05 mA or less Rated voltage input: Max. input rating 30 V or less, ON voltage 7.5 V or more, OFF current 0.05 mA or less ^3 Rated NPN open collector output: Max. 100 mA/ch (20 mA/ch when expansion units are connected), 30 V or less, residual voltage 1 V or less Rated PNP open collector output: Max. 50 mA/ch (20 mA/ch when expansion units are connected), power voltage or less, residual voltage 2 V or less ^4 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^*5 Does not include the power consumption of the load. The power consumption with expansion units installed is the total of each amplifier unit’s power consumption. Example: When using one main unit (IB-1000) with two expansion units (IB-1050) (2400 mW X 1) + (2400 mW X 2) = 7200 mW

Keyence IB-1050 Keyence

$640.67

Only 5 units left

Specifications

Model		IB-1050
Type		DIN rail mount
Main unit/Expansion unit		Expansion unit
Head compatibility		Yes
Display	Display resolution	0.01 %, 0.1 %, 1 % (switchable)
	Display range	–99.999 to 99.999, –99.99 to 99.99 –99.9 to 99.9, –99 to 99 (switchable)
	Digital display method	Dual7-segmentdisplay Upper level: 5 red digits Lower level: 5 green digits
	Operating indicators	Judgment indicator: 2-color (green/red) LED (HI, GO, LO) Bank indicator: Green LED x 4 Laser emission warning indicator: Green LED Others: Green LED x 8, red LED x 3
Analog output voltage		No
Analog current output
Control Input	Bank switch input, zero shift input	Non-voltage input ^*1
Control input	Zero shift input
	Laser emission stop input
	Timing input
	Reset input
	Adjust input
Control output	Judgment output (check output)	Open collector (NPN/PNP switchable, N.O./N.C. switchable) ^*2
Power supply	Power consumption	2400 mW or less (at 30 V, 80 mA max.) ^3 ^4 (including analog current output)
	Power voltage	Supplied from main unit ^*3
Environmental resistance	Pollution degree	2
	Ambient temperature	-10 to +50 °C (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, compound amplitude 1.5 mm, 2 hours each for X, Y, Z axes
Material		Main unit case/Front panel: polycarbonate, keytop: polyacetal, cable: PVC
Weight		Approx. 140 g (including accessories)
^1 The four external input wires are assigned with desired inputs. Rated no-voltage input: ON voltage 2 V or less, OFF current 0.05 mA or less Rated voltage input: Max. input rating 30 V or less, ON voltage 7.5 V or more, OFF current 0.05 mA or less ^2 Rated NPN open collector output: Max. 100 mA/ch (20 mA/ch when expansion units are connected), 30 V or less, residual voltage 1 V or less Rated PNP open collector output: Max. 50 mA/ch (20 mA/ch when expansion units are connected), power voltage or less, residual voltage 2 V or less ^3 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^4 Does not include the power consumption of the load. The power consumption with expansion units installed is the total of each amplifier unit’s power consumption. Example: When using one main unit (IB-1000) with two expansion units (IB-1050) (2400 mW X 1) + (2400 mW X 2) = 7200 mW

Keyence IB-1000 Keyence

$606.14

Only 9 units left

Specifications

Model		IB-1000
Type		DIN rail mount
Main unit/Expansion unit		Main unit
Head compatibility		Yes
Display	Display resolution	0.01 %, 0.1 %, 1 % (switchable)
	Display range	–99.999 to 99.999, –99.99 to 99.99 –99.9 to 99.9, –99 to 99 (switchable)
	Digital display method	Dual7-segmentdisplay Upper level: 5 red digits Lower level: 5 green digits
	Operating indicators	Judgment indicator: 2-color (green/red) LED (HI, GO, LO) Bank indicator: Green LED x 4 Laser emission warning indicator: Green LED Others: Green LED x 8, red LED x 3
Analog output voltage		±5 V, 1 to 5 V, 0 to 5 V Output impedance 100 Ω ^*1
Analog current output		4 to 20 mA Maximum load resistance 350 Ω ^*1
Control Input	Bank switch input, zero shift input	Non-voltage input ^*2
Control input	Zero shift input
	Laser emission stop input
	Timing input
	Reset input
	Adjust input
Control output	Judgment output (check output)	Open collector (NPN/PNP switchable, N.O./N.C. switchable) ^*3
Power supply	Power consumption	2400 mW or less (at 30 V, 80 mA max.) ^4 ^5 (including analog current output)
	Power voltage	10 to 30 VDC, including ripple (P-P) 10% Class 2 or LPS ^*4
Environmental resistance	Pollution degree	2
	Ambient temperature	-10 to +50 °C (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, compound amplitude 1.5 mm, 2 hours each for X, Y, Z axes
Material		Main unit case/Front panel: polycarbonate, keytop: polyacetal, cable: PVC
Weight		Approx. 150 g (including accessories)
^1 ±5 V, 1 to 5 V, 0 to 5 V, or 4 - 20 mA should be selected. ^2 The four external input wires are assigned with desired inputs. Rated no-voltage input: ON voltage 2 V or less, OFF current 0.05 mA or less Rated voltage input: Max. input rating 30 V or less, ON voltage 7.5 V or more, OFF current 0.05 mA or less ^3 Rated NPN open collector output: Max. 100 mA/ch (20 mA/ch when expansion units are connected), 30 V or less, residual voltage 1 V or less Rated PNP open collector output: Max. 50 mA/ch (20 mA/ch when expansion units are connected), power voltage or less, residual voltage 2 V or less ^4 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^*5 Does not include the power consumption of the load. The power consumption with expansion units installed is the total of each amplifier unit’s power consumption. Example: When using one main unit (IB-1000) with two expansion units (IB-1050) (2400 mW X 1) + (2400 mW X 2) = 7200 mW

Previous Page 24 / 30Next

Filters

In stock (386)
Out of stock (658)