Measurement Sensors

Filters

In stock (386)
Out of stock (658)

Showing 529 - 552 of 719 products

$374.06

Only 6 units left

Specifications

Model		EX-416V^*1
Type		Sensor head
Amplifier unit		NPN: EX-V05 PNP: EX-V05P
Shape		ø14.5 x 20 mm ø0.57" x 0.79" Cylindrical, threaded
Measuring range		0 to 5 mm 0 to 0.20"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		1 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		NPN open-collector or non-voltage contact (Timing input, Reset input, Auto-zero input, Comparator output disable input, Synchronous input, External setting input)/PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.) PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	-10 to +60 °C 14 to 140 °F, No freezing
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 75 g (including 3 m 9.8' cable)
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-305V Keyence

$228.27

In stock, 11 units

Specifications

Model		EX-305V^*1
Type		Sensor head
Amplifier unit		NPN: EX-V01 PNP: EX-V01P
Shape		ø5.4 x 18 mm ø0.21" x 0.71" Cylindrical
Measuring range		0 to 1 mm 0 to 0.04"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		NPN open-collector or non-voltage contact (Timing input, Reset input, Auto-zero input, Comparator output disable input, Synchronous input, External setting input)/PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.) PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	-10 to +60 °C 14 to 140 °F, No freezing
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 45 g (including 3 m 9.8' cable)
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V64P Keyence

$2,657.84

Only 2 units left

Specifications

Model		EX-V64P^*1
Type		Amplifier Unit PNP
Shape		14 x 30 x 4.8 mm 0.55" x 1.18" x 0.19" Thin profile
Measuring range		0 to 4 mm 0.157"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		1 µm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	0 to 50°C 32 to 122 °F
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V64E Keyence

$0.00

Sold Out

Specifications

Model		EX-V64E
Type		Controller
Shape		14 x 30 x 4.8 mm 0.55" x 1.18" x 0.19" Thin profile
Measuring range		0 to 4 mm 0.16"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		1 µm
Sampling rate		40,000 samplings max./sec. ^*1
Display speed		20 times/sec. (2-color, 7-segment LED)
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input	Timing input	NPN open-collector or non-voltage contact signal
	Reset input
	Auto-zero input
	Judgment output: Inhibit input
	Synchronization/external settings input
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms (ON/OFF selectable)
Strobe output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*2
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	240 mA or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^2 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V10P Keyence

$2,687.56

Only 2 units left

Specifications

Model		EX-V10P^*1
Type		Amplifier Unit PNP
Shape		ø22 x 35 mm ø0.87" x 1.38" Cylindrical, threaded
Measuring range		0 to 10 mm 0" to 0.394"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		2 µm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	0 to 50°C 32 to 122 °F
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V10E Keyence

$7,187.60

Only 4 units left

Specifications

Model		EX-V10E
Type		Controller
Shape		ø22 x 35 mm ø0.87" x 1.38" Cylindrical, threaded
Measuring range		0 to 10 mm0" to 0.394"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		2 µm
Sampling rate		40,000 samplings max./sec. ^*1
Display speed		20 times/sec. (2-color, 7-segment LED)
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input	Timing input	NPN open-collector or non-voltage contact signal
	Reset input
	Auto-zero input
	Judgment output: Inhibit input
	Synchronization/external settings input
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms (ON/OFF selectable)
Strobe output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*2
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	240 mA or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^2 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V05P Keyence

$2,652.04

Only 5 units left

Specifications

Model		EX-V05P^*1
Type		Amplifier Unit PNP
Shape		ø14.5 x 20 mm ø0.57" x 0.79" Cylindrical, threaded
Measuring range		0 to 5 mm 0.20"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		1 µm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	0 to 50°C 32 to 122 °F
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V05E Keyence

$1,073.25

Only 1 unit left

Specifications

Model		EX-V05E
Type		Controller
Shape		ø14.5 x 20 mm ø0.57" x 0.79" Cylindrical, threaded
Measuring range		0 to 5 mm 0.20"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		1 µm
Sampling rate		40,000 samplings max./sec. ^*1
Display speed		20 times/sec. (2-color, 7-segment LED)
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input	Timing input	NPN open-collector or non-voltage contact signal
	Reset input
	Auto-zero input
	Judgment output: Inhibit input
	Synchronization/external settings input
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms (ON/OFF selectable)
Strobe output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*2
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	240 mA or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^2 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V02P Keyence

$2,308.18

Only 2 units left

Specifications

Model		EX-V02P^*1
Type		Amplifier Unit PNP
Shape		M10 x 18 mm 0.71" Threaded
Measuring range		0 to 2 mm 0.08"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	0 to 50°C 32 to 122 °F
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V02E Keyence

$2,876.92

Only 1 unit left

Specifications

Model		EX-V02E
Type		Controller
Shape		M10 x 18 mm 0.71" Threaded
Measuring range		0 to 2 mm 0.08"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 µm 0.016 Mil
Sampling rate		40,000 samplings max./sec. ^*1
Display speed		20 times/sec. (2-color, 7-segment LED)
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input	Timing input	NPN open-collector or non-voltage contact signal
	Reset input
	Auto-zero input
	Judgment output: Inhibit input
	Synchronization/external settings input
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms (ON/OFF selectable)
Strobe output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*2
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	240 mA or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^2 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V01P Keyence

$2,384.29

Only 2 units left

Specifications

Model		EX-V01P^*1
Type		Amplifier Unit PNP
Shape		ø5.4 x 18 mm ø0.21" x 0.71" Cylindrical
Measuring range		0 to 1 mm 0.04"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	0 to 50°C 32 to 122 °F
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence EX-V01E Keyence

$1,188.93

Only 1 unit left

Specifications

Model		EX-V01E
Type		Controller
Shape		ø5.4 x 18 mm ø0.21" x 0.71" Cylindrical
Measuring range		0 to 1 mm 0.04"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 µm 0.016 Mil
Sampling rate		40,000 samplings max./sec. ^*1
Display speed		20 times/sec. (2-color, 7-segment LED)
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input	Timing input	NPN open-collector or non-voltage contact signal
	Reset input
	Auto-zero input
	Judgment output: Inhibit input
	Synchronization/external settings input
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms (ON/OFF selectable)
Strobe output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*2
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	240 mA or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 235 g
^1 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^2 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence SI-F80RU Keyence

$0.00

Sold Out

Specifications

Model		SI-F80RU
Type		Wafer Thickness Measurement Type Spectrum Unit
Measurement range		10 to 310 µm 0.000394" to 0.0122" (when n=3.5)^*1
Possible detection distance		80 to 81.1 mm 3.15" to 3.19"
Light source		Infrared SLD Output 0.6 mW, Class 1 Laser Product (IEC60825-1, FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø25 µm^*3
Linearity		±0.1 µm ±0.000004" (when n=3.5)^*4
Resolution		0.001 µm ^*5
Sampling cycle		200 µs
LED display		Target near center of measurement range : green lights. Target within measurement range : orange lights. Target outside measurement range : flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	-
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1.2 kg
^1 Indicates the thickness measurement range when the refractive index is 3.5. (The thickness measurement range is 35 to 1100 µm0.001378" to 0.0433" when the refractive index is 1.) ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained by measuring the gap between two glass plates with the number of averaging measurements set to 256, converted to a refractive index of 3.5. ^*5 This value is obtained by measuring a 0.3 mm thick glass target within the possible detecting distance with the number of averaging measurements set to 4,096.

Keyence SI-F80R Keyence

$0.00

Sold Out

Specifications

Model		SI-F80R^*1
Type		Wafer thickness measurement type Sensor head
Measurement range		10 to 310 µm 0.000394" to 0.0122" (when n=3.5)^*2
Possible detection distance		80 to 81.1 mm 3.15" to 3.19"
Light source		Infrared SLD Output 0.6 mW, Class 1 Laser Product (IEC60825-1, FDA (CDRH) Part 1040.10^*3)
Spot diameter		ø25 µm ø0.000984"^*4
Linearity		±0.1 µm ±0.000004" (when n=3.5)^*5
Resolution		0.001 µm ^*6
Sampling cycle		200 µs
LED display		Target near center of measurement range : green lights. Target within measurement range : orange lights. Target outside measurement range : flashes orange.
Temperature fluctuation		―
Environmental resistance	Enclosure rating	IP64
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		SUS
Weight		Approx. 70 g (including cable)
^1 The sensor head and spectrum unit are calibrated as a pair. They are not interchangeable. ^2 Indicates the thickness measurement range when the refractive index is 3.5. (The thickness measurement range is 35 to 1100 µm0.001378" to 0.0433" when the refractive index is 1.) ^3 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^4 Indicates the minimum beam spot diameter within the measurement range. ^5 This value is obtained by measuring the gap between two glass plates with the number of averaging measurements set to 256, converted to a refractive index of 3.5. ^6 This value is obtained by measuring a 0.3 mm 0.01" thick glass target within the possible detection distance with the number of averaging measurements set to 4096.

Keyence OP-84480 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-84474 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-84427 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-51656 Keyence

$513.00

Only 3 units left

Specifications

Model				OP-51656
Cable length				10 m 32.8'

Keyence OP-51655 Keyence

$0.00

Sold Out

Specifications

Model				OP-51655
Cable length				3 m 9.8'

Keyence SI-H13 Keyence

$0.00

Sold Out

Specifications

Model				SI-H13^*1
Type				Configuration Software for the SI Series
Operating System				Windows 11 Pro Windows 10^2 Windows 7 (SP1 or later)^3 Windows Vista (SP2 or later)^4 Windows XP (SP3 or later)^5
CPU				Pentium III 1 GHz or higher (1.7 GHz or higher recommended)
Memory capacity				256 MB or more (1 GB or more recommended)
Available hard disk space				1 GB or more
Display				1024 x 768 pixels, 24-bit full color or better
PC interface				The PC must be equipped with one of these interfaces: USB: Revision 2.0 HighSpeed (USB1.1 compatible full speed)^6 LAN: 100BASE-TX, 10BASE-T^7 RS-232C (serial port)
^1 Use under an environment that exceeds the recommended environment of the your OS. ^2 Editions supported: Home, Pro, Enterprise. ^3 Editions supported: Home Premium, Professional, Ultimate. ^4 Editions supported: Ultimate, Business, Home Premium, Home Basic. ^5 Supports Professional and Home Edition. ^6 Does not support connection via a USB hub. ^*7 Does not support connection via private LANs or routers. Use in a 1:1 or local connection.

Keyence SI-H1 Keyence

$0.00

Sold Out

Specifications

Model				SI-H1^*1
Type				Configuration Software for the SI Series
Operating System				Windows 11 Pro Windows 10^2 Windows 7 (SP1 or later)^3 Windows Vista (SP2 or later)^4 Windows XP (SP3 or later)^5
CPU				Pentium III 1 GHz or higher (1.7 GHz or higher recommended)
Memory capacity				256 MB or more (1 GB or more recommended)
Available hard disk space				1 GB or more
Display				1024 x 768 pixels, 24-bit full color or better
PC interface				The PC must be equipped with one of these interfaces: USB: Revision 2.0 HighSpeed (USB1.1 compatible full speed)^6 LAN: 100BASE-TX, 10BASE-T^7 RS-232C (serial port)
^1 Use under an environment that exceeds the recommended environment of the your OS. ^2 Editions supported: Home, Pro, Enterprise. ^3 Editions supported: Home Premium, Professional, Ultimate. ^4 Editions supported: Ultimate, Business, Home Premium, Home Basic. ^5 Supports Professional and Home Edition. ^6 Does not support connection via a USB hub. ^*7 Does not support connection via private LANs or routers. Use in a 1:1 or local connection.

Keyence SI-F80U3 Keyence

$1,847.96

Only 1 unit left

Specifications

Model		SI-F80U3
Measurement range		0.05 to 1.1 mm 0.002" to 0.04" ^*1 (Possible detection distance : 80 to 81.1 mm 3.15" to 3.19")
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 The thickness measurement type sensor head displays the measurement range for the distance between plates of glass. Ensure that the measurement target is within the possible detection distance range. ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained by measuring the gap between two glass plates with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence SI-F80U Keyence

$0.00

Sold Out

Specifications

Model		SI-F80U
Type		Thickness measurement type Spectrum unit
Measurement range		0.05 to 1.1 mm 0.002" to 0.04" ^*1 (Possible detection distance : 80 to 81.1 mm 3.15" to 3.19")
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø20 µm ø0.000787"^*3
Linearity		±0.2 µm ±0.000008" ^*4
Resolution		0.001 µm ^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	-
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 The thickness measurement type sensor head displays the measurement range for the distance between plates of glass. Ensure that the measurement target is within the possible detection distance range. ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained by measuring the gap between two glass plates with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a 0.3 mm 0.01" thick glass target within the possible detection distance with the number of averaging measurements set to 4,096.

Keyence SI-F10U3 Keyence

$0.00

Sold Out

Specifications

Model		SI-F10U3
Measurement range		11.3 to 12.35 mm 0.04" to 0.49" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø40 µm ø0.001575"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 650 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	35 to 80 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Weight		Approx. 1 kg
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Previous Page 23 / 30Next

Filters

In stock (386)
Out of stock (658)