Machine Vision Systems

$0.00

Sold Out

Specifications

Model				CA-DZR5
LED color				red
Power consumption				2.5 W
Weight				Approx 240 g

Keyence AP-41M Keyence

$0.00

Sold Out

Specifications

Model		AP-41M
Application		Gauge pressure
Type		Negative pressure
Rated pressure		0 to -101.3 kPa
Fluid type		Air, non-corrosive gasses
Temperature characteristics		±2 % of F.S. (When the temperature varies from 25 °C 77 °F)
Pressure port		M3 male threaded
Environmental resistance	Pressure resistance	500 kPa
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 4 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 10 times in each of X, Y and Z directions, total of 60 times
Material		Case: PBT, Screw: SUS303, Cable: PVC
Weight		Approx. 68 g (including cable)

Keyence CA-HL08MX Keyence

$3,244.44

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence EM-014A Keyence

$0.00

Sold Out

Specifications

Model		EM-014A^*1
Type		Shielded
Shape		M14 Threaded
Detecting distance		4.0 mm 0.16" ±10%
Detectable object		Ferrous metals (see Characteristics for non-ferrous metals)
Standard target (iron, t=1 mm 0.04")		15 x 15 mm 0.59" x 0.59"
Hysteresis		10% max. of detecting distance
Response frequency		1.2 kHz
Operation mode		N.O.
Temperature characteristics		±10% max. of detecting distance at +23°C 73.4°F, within -10 to +70°C 14 to 158°F
Display indicator		Red LED
Control output		NPN: 200 mA (40 V) max., Residual voltage: 1 V max.
Housing		Cr-plated brass
Rating	Power voltage	10.8 to 30 VDC, Ripple (P-P) 10 % or less^*2
	Current consumption	12 mA or less
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +80 °C -13 to 176 °F (No freezing)
	Relative humidity	35 to 95 % RH (No condensation)
Weight		Approx. 60 g (including nuts and 2-m 6.6' cable)
^1 The alternate-frequency type of EM-014 ^2 Make sure that the power voltage stays within 10.8 V to 30 V even if it is affected by ripple effects.

Keyence GL-VCC5 Keyence

$0.00

Sold Out

Specifications

Model				GL-VCC5
Type				Extension cable
Number included				1 pc.
Cable end				Female side: M12 connector 5 pin Male side: M12 connector 5 pin
Number of cores				5
Length				5 m 16.4'
Material				connector: PVC/Nickel-plated brass cable: PVC
Weight				300 g

Keyence ER-N12 Keyence

$0.00

Sold Out

Specifications

Model		ER-N12
Type		Separate amplifier Amplifier unit Expansion unit (cable type)
No. of control outputs		2
No. of external inputs		1
Temperature characteristics		±8% or less of detecting distance at +25°C +77°F (-25 to +55°C -13°F to +131°F) ^*1
Response time		150 μs ^2/ 300 μs ^2/ 1 ms / 4 ms / 16 ms / 64 ms (switchable)
Network compatibility		NU Series
Function	Operation mode	Normal / Magnetic metal / Non-magnetic metal / Hybrid
	Timer function	Timer OFF / Off Delay / On Delay / One Shot / On-Off Delay / On-Delay One Shot
I/O	Control output	Open-collector, 30 VDC or less, PNP/NPN switchable When used as a solitary unit: 100 mA or less for 1 output; 100 mA or less in total for 2 outputs / When used as an expansion unit: 50 mA or less in total for 2 outputs Residual voltage: 1.7 V or less (Output current: 10 mA or less) / 2.4 V or less (Output current: 10 to 100 mA)
	External input	Tuning / Detection stop / Zero shift / Hold value reset (switchable) Short-circuit current: 1.5 mA or less; Input time: 3 ms or more ON, 20 ms or more OFF (When tuning is selected: 25 ms or more ON, 25 ms or more OFF)
Additional expansion units		Up to 8 units (9 units connected in total including the main unit); Up to 16 units when connecting an ER-N10 to an NU Series device
Protection circuit		Protection against reverse power connection, output overcurrent, output surge, and reverse output connection
No. of mutual interference prevention units		OFF / 4 units / 8 units (selectable) ^*3
Power supply	Power voltage	18 to 30 VDC ^*4 (including 10% or less ripple (P-P)), Class 2
	Power consumption (excluding load current)	1110 mW or less (47 mA or less at 24 V, 62 mA or less at 18 V)
Environmental resistance	Ambient temperature	Operation: -25 to +55°C -13°F to +131°F ^*5, Storage: -30 to 70°C -22°F to +158°F (no freezing)
	Relative humidity	Operation/storage: Up to 85% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	500 m/s² 1640.4 ft/s² (50 G), 10 times in each of the X, Y, and Z directions
Case material		Main unit and cover: Polycarbonate, FG terminal: Copper/iron, Sheet metal: Aluminum alloy, M8 connector metal: Nickel-plated brass
Accessories		Instruction manual
Weight		Approx. 90 g 3.18 oz
^1 The value when the operation mode is set to “Normal”, using the 2-point adjust function at a distance of 25% of the stable detection range with no detectable object, and a standard detectable object is placed at a distance of 50% of the stable detection range. ^2 150 μs and 300 μs are selectable only when the operation mode is set to “Normal”. ^3 The response time changes as follows when 4 or 8 units are selected as the number of interference prevention units. When set to 4 units: 5 ms / 10 ms / 40 ms / 170 ms / 700 ms (switchable), When set to 8 units: 10 ms / 20 ms / 70 ms / 300 ms / 1.2 s (switchable) ^4 Use a power voltage of 20 V or more when connecting 4 or more expansion units. ^*5 When 1 or 2 units are added: -25 to +55°C -13°F to +131°F; when 3 to 10 units are added: -25 to +50°C -13°F to +122°F; when 11 to 16 units are added: -25 to +45°C -13°F to +113°F. When using two outputs, one unit is counted as two units. The prescribed values for the operating ambient temperature assume the sensor amplifier is mounted on a DIN rail installed on a metal surface. Exercise special care when installing the product in an airtight space.

Keyence FL-CP160 Keyence

$0.00

Sold Out

Specifications

Model				FL-CP160
Total length (at 25 °C)				1613
Measurement range (dead zone excluded)				1,557 (1,537)^*1
Weight				Approx. 880 g
^*1 Values for water. For oil

Keyence EH-108 Keyence

$146.33

In stock, 36 units

Specifications

Model		EH-108
Type		Oil-resistant, Shielded, Threaded^*1
Detectable object		Ferrous metals (see Characteristics for nonferrous metals)
Standard target (iron, t=1 mm 0.04")		10 x 10 mm 0.39" x 0.39"
Stable detecting range		0 to 1.5 mm0.06"
Maximum detecting distance		2.5 mm0.10"
Hysteresis		0.07 mm0.003"
Repeatability		0.005 mm0.0002"
Temperature characteristics		±10% max. of detecting distance at 23°C 73.4°F, within -10 to +60°C 14 to 140°F
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 51 g (including nuts and 3-m 9.8' cable)
^*1 Not designed for immersed use.

Keyence OP-51464 Keyence

$0.00

Sold Out

Specifications

Model				OP-51464
Overview				Front protective cover protecting detection side of light curtain.
Applicable product				SL-V95F, SL-V48H, SL-V24L, SL-C48H, SL-C24L
Number included				1 pcs.
Length				950.3 mm 37.41"
Material				Translucent plastic: Polycarbonate (t=Approx. 1.15mm), Black plastic: ABS
Note				To install this product on both the transmitter and receiver, 2 sets are required. Use the dimming filters (sold separately) by attaching them to the front protection cover. When the front protection cover is attached, the L-shaped mounting bracket (OP-42

Keyence AG-410 Keyence

$1,290.22

Only 4 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence LV-NH47 Keyence

$565.76

Only 1 unit left

Specifications

Model		LV-NH47
Type		Definite-reflective
FDA (CDRH) Part 1040.10		Class 1
IEC 60825-1
Light source		Visible semiconductor laser, Wavelength: 660 nm
Detecting distance	MEGA	55 to 85 mm 2.17" to 3.35"
	ULTRA
	SUPER
	TURBO
	FINE
	HSP
Environmental resistance	Ambient temperature	-10 to +55°C 14°F to 131°F (No freezing)
	Relative humidity	35 to 85% RH (No condensation)
Material	Case	Glass-reinforced plastic
	Lens cover	Transmitter: Glass Receiver: Polyarylate
Weight		Approx. 70 g 2.47 oz

Keyence LC-2400A Keyence

$17,330.63

Only 7 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SV2-D20B Keyence

$0.00

Sold Out

Specifications

Model				SV2-D20B
Type				Motor power cable, Standard cable with electromagnetic brake
Length				20 m 65.6'
Note				for 200 W / 400 W motor

Keyence XM-H5C Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence NR-EN16 Keyence

$2,307.66

Only 5 units left

Specifications

Model				NR-EN16 ^*1
Connection target devices				DL-EN1 (Connected sensor: GT2 Series, GT Series, IL Series, IG Series, IB Series, IX Series, SK Series)^2 NQ-EP4L (Connected sensor: FD-Q Series,FD-R Series, FD-X Series, FD-G Series, LR-T Series, FL Series, GP-M Series, FD-H Series, FD-EP Series, FD-EC Series, FI-1000, FI-T Series)^2; LK-G5000 Series, CL-3000 Series, LJ-V7000 Series, LJ‑X8000 Series, LS-9000 Series; Connection of one of the above devices per NR-EN16 allowed
Connection target device identification				Automatic identification or manual identification by specifying the IP address
Communication protocols				Ethernet TCP/UDP communication, BOOTP/DHCP client supported (compatible with the above connection target devices)
Interface				Ethernet 100Base-TX (AUTO-MDI/MDIX-compatible), 1 port^*3
Number of channels				16 ch max. (varies depending on connected devices)
Collection period				Maximum sampling cycle: 1 ms (1 kHz) to 60 s With effective rate display function for communication between connected sensors^*4
Buffer memory				8M data^*5
Sensor power output function				• Output from power supply output connector (4-pole terminal block) (switchable between output ON and OFF) • Output voltage: 24 VDC ±10% • Rated current: Max. 0.6 A (switchable between 0.3 A and 0.6 A) • Built-in overcurrent protection function: Automatic recovery, switchable between 0.35 A (typ.) and 0.70 A (typ.) protection current • Class 2 power supply (CSA C22.2 No. 223 / UL 1310 compliant) • Sensor power supply not insulated from system bus
Power consumption				1.6 W or less^*6
Surrounding air temperature				0 to +40°C 32°F to 104°F
Operating ambient humidity				10 to 85% RH (no condensation)
Weight				Approx. 150 g 5.30 oz (including approx. 10 g 0.35 oz for the OP-88513 (NR-EN16 power supply terminal block))
^1 For NR-EN16 units, connect the Ethernet cable directly to the target device. Operation with hubs is not guaranteed. ^2 Multiple sensors can be connected to each DL-EN1/NQ-EP4L. The number of connectable sensors depends on the DL-EN1/NQ-EP4L. ^3 Max. expansion: 18 ports (with 18 units connected, using NR-X100W), 4 ports (with 4 units connected, using NR-500). Up to 4 units can be connected for each NR-X100W and NR-XR01 group when using the NR-X100W, with up to 18 units for all groups. ^4 The effective rate may vary depending on the connected sensor and the communication conditions. ^5 Limited by the NR-X100W buffer memory when using the NR‑X100W. ^6 When using the power supply output function, the unit power consumption is calculated as follows regardless of the actual power output (load). Set to 0.3 A output = 10.0 W; Set to 0.6 A output = 20.0 W. The power supply output function can be set using a switch on the unit body.

Keyence OP-88289 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence KV-N16ER Keyence

$1,238.46

Only 5 units left

Specifications

Model			KV-N16ER
Expansion output unit	Output Points		16 points
	External connectionmethod		Relay
	External connection method		Terminal block
	Rated load		250 VAC/30 VDC, 2 A
	Leakage current (when output is OFF)		−
	Residual voltage (at ON)
	ON resistance		50 mΩ or less
	Common method		4 points/1 common (8 terminals) ^*1
	Response time	OFF to ON	10 ms or less
		ON to OFF
	Relay life		Electrical: 100000 cycles or more (20 cycles/minute) Mechanical: 20000000 cycles or more
	Relay replacement		Impossible
Internal current consumption			100 mA or less
Weight			Approx. 260 g
^*1 The KV-N16ER has two terminals for each of C0, C1, C2, and C3 respectively, which are shorted internally. (C0, C1, C2, and C3 are independent.)

Keyence FD-XS8 Keyence

$1,089.12

Only 10 units left

Specifications

Model				FD-XS8
Supported pipe materials				Metal pipes, Plastic pipes (soft/hard) ^*1
Supported fluids				Liquids (water, oil, adhesive, grease, chemical solutions, etc.) ^*1
Supported fluid temperature				0 °C (no freezing on the pipe surface) to 100 °C 32 to 212 °F (Pipe surface temperature)
Clamp set model	Plastic pipe/tube attachment			FD-XC8R1, FD-XC8R2, FD-XC8R3
	Metal pipe attachment			FD-XC8M^*2
Maximum rated flow rate				Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : 0 to 3000 mL/min Outer diameter of pipe ø 8 0.31 ": 0 to 8000 mL/min
Zero cut flow rate				40 mL/min^*3 (variable, default)
Display resolution	Instantaneous flow rate			0.1/1/10 mL/min (Displayed on controller)
	Shot amount			0.001/0.01/0.1/1 mL (Displayed on controller)
Repeatability	Plastic pipe/tube attachment	Response time: 50 ms	F.S.	± 0.1 %^4^5
			Instantaneous flow rate	Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : ±3 mL/min Outer diameter of pipe ø 8 0.31 ": ±8 mL/min^4^5
		Response time: 500 ms		Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : ±1.0 mL/min Outer diameter of pipe ø 8 0.31 ": ±2.6 mL/min^*4
	Metal pipe attachment	Response time: 50 ms	F.S.	Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : ±0.3 % Outer diameter of pipe ø 8 0.31 ": ±0.15 %^4^5
			Instantaneous flow rate	Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : ±9 mL/min Outer diameter of pipe ø 8 0.31 ": ±12 mL/min^4^5
		Response time: 500 ms		Outer diameter of pipe ø 6 0.24 ", 1/4 " (6.35 mm) : ±2.9 mL/min Outer diameter of pipe ø 8 0.31 ": ±3.8 mL/min^*4
Hysteresis				Variable
Integrated unit display				0.1/1/10/100/1000/10000 mL (displayed on controller)
Display method				Status indicator
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529) , IP68G (JIS C0920) ^*6
	Ambient temperature			-10 to 60 °C (No freezing) 14 to 140 °F
	Relative humidity			35 % to 85 %RH (No condensation)
	Vibration resistance			10 to 55 Hz, double amplitude 1.5 mm 0.06 ", 2 hours each for X,Y,Z direction
	Shock resistance			50 G 11 ms 3 times each for X,Y,Z direction
Material	Sensor head			Head body: PPS/PPSU, in-cable amplifier: PPS, cable: PVC, controller connector: PPS/PBT/POM
	Clamp set	For plastic pipe		Body, fixing screw: PPS, detection surface: special rubber, pipe support rubber: FKM, sensor head fixing screw: SUSXM7
		For metal pipe		Metal: SUS304/SUSXM7, detection surface: special rubber, clamp support rubber: FKM, sensor head fixing screw: SUSXM7
Weight				Approx. 250 g
^1 Liquid must allow for the passage of an ultrasonic pulse, as well as not contain large air pockets or excessive bubbles. Readings may become unstable depending on the type of pipe. ^2 When using stainless steel or iron pipes, the ideal pipe wall thickness is as follows, FD-XS1: approx. 0.5 mm 0.02", FD-XS8: approx. 1 mm 0.04", FD-XS20: approx. 1 0.04" to 2 mm 0.08". FD-X signal strength and stability will decrease as the thickness of the pipe wall increases or decreases from the suggested size. ^3 The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate. ^4 This specification is valid when the flow velocity distribution is stable. This value does not take into account the effects of pulsation or fluctuations in flow velocity distribution due to facility factors. Convert the F.S. (full scale value) listed in the table according to the rated flow range. ^5 The longer the response time is set, the more repeatability is improved. As a guideline, use √ (50 ms/response time) times. ^6 The connector part of the sensor head cable is IP65/IP67.

Keyence SJ-H228C Keyence

$0.00

Sold Out

Specifications

Model		SJ-H228C
Type		HC
Ion generation method		Corona discharge
Structure		Shock-proof, resistance-coupled
Voltage application method/applied voltage		Pulse AC method/±7000 V
Ion balance control method		Dual I.C.C. method
Ion balance		±30 V ^*1
Cleanliness		ISO 14644-1 Class 2 ^*2
Operating distance		50 to 2000 mm 1.97" to 78.74"
Control input		NPN open collector or non-voltage contact signal
Control output		NPN type photorelay, 100 mA max. (at 40 V max.)
Major functions		Condition alarm output, ion level alarm output, alarm output
Air purge connection port		Rc 1/8
Air purge supplied pressure		0.5 MPa or less ^*3
Effective length		2280 mm 89.76" ^*4
No. ofelectrodes		36
Static elimination bar length		2240 mm 88.19"
Rating	Power voltage	24 VDC-36 V±10%
	Current consumption	500 mA (at 24 VDC)/350 mA (at 36 VDC)
	Overvoltage category	I
	Pollution degree	2
Environmental resistance	Ambient temperature	0 to +40°C 32.0°F to 104.0°F
	Relative humidity	35 to 85% RH (No condensation)
Material	Electrode probe	Silicon
	Main unit	ABS resin/PC
Weight	Static elimination bar	2350 g 82.89 oz
^1 Value measured under the following conditions: Operating distance: 300 mm 11.81" Air supply pressure: 0.2 MPa Frequency: 68 Hz Ambient operating temperature: 0 to +40°C 32.0°F to 104.0°F Ambient operating humidity: 35 to 65%RH Measurement position: Center of bar Under a 0.3 m/s 1.0 ft/s downflow ^2 Contact KEYENCE for detailed conditions. ^3 Contact KEYENCE when using the air purge function with intermittent air supply. ^*4 Effective length is for static elimination range when installation distance is 50 mm 1.97".

Keyence CV-L35 Keyence

$0.00

Sold Out

Specifications

Model				CV-L35
Focal point				35 mm 1.38"
F-stop range (aperture)				F1.6 to F16
Minimum WD				0.3 m 1.0'
Mount				C-mount
Filter size				30.5 mm 1.20" P0.5
Compatible image sensor size				2/3"
TV distortion				-0.2 % (-0.08 %)^*1
Resolving power				100 cycles/mm at center, 40 cycles/mm on periphery
Ambient temperature/humidity range				0 to +50 °C 32 to 122°F, 35 to 80 % RH (No condensation)
Polarizing filter				OP-54030
Protective filter				CA-LF30
Weight				Approx. 85 g
^*1 Indicates specification for compatible image sensor size. Value in parenthesis applies to 1/3" image sensor size.

Keyence RB-500 Keyence

$5,380.80

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence BZ-H5XZ Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence KV-FL20 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CA-LH50G Keyence

$942.69

Only 3 units left

Specifications

Model		CA-LH50G
Type		Vibration-resistant models
Compatible image sensor size		2/3"
Focal point		50 mm 1.97"
F-stop range (aperture)		F2.8/4/8/16^*1
Minimum WD		0.2 m 0.7'^*2
Resolving power		100 cycles/mm (center), 80 cycles/mm (periphery)
Filter size		27.0 mm 1.06" P0.5
TV distortion		-0.03 % (-0.01 %)^*3
Mount		C-mount
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 80 % RH (No condensation)
Weight		Approx. 76 g
^1 The vibration-resistant types are designed to have their apertures replaced. When shipped, the OPEN aperture is attached to the lens, so replace this with one of the other included apertures (F4, F8, or F16) as necessary. To use the f-stop (aperture) in the OPEN mode, use the lens without removing the OPEN aperture. ^2 Installing the lens at a distance from the target shorter than the minimum working distance listed in the specifications makes it very likely that the lens will drop out due to vibrations. If the lens is installed in such a position, implement separate countermeasures to prevent the lens from dropping out. ^*3 This indicates the specification for the compatible image sensor size. The value in parentheses applies to a 1/3" image sensor size.