Machine Vision Systems

$3,265.99

Only 1 unit left

Specifications

Model		NR-X100W
Main unit buffer memory capacity		50M data^*1
Expansion memory		SD card (SD/SDHC)^*2
PC interface	USB	USB mini-B connector, USB 2.0 High-speed–compliant, Simultaneous USB connection from one PC to up to four units (switchable by ID switch)
	Ethernet	RJ45 connector, 100Base-TX (AUTO MDI/MDIX supported) ^*3
	Wireless LAN	Connection via NR-XW1 wireless LAN unit, IEEE 802.11b/g/n ^*3
Network function		FTP client function, FTP server function, SNTP client function
Display/operation		Operation via NR-XCP30 control panel, or via WAVE LOGGER X with PC connection
Expansion remote unit connection		Dedicated remote connection connector × 2 (Remote OUT A port, B port) Unit expansion possible by connecting up to eight NR-XR01 remote units (connected by remote unit cable)
Number of connectable measurement units	Master data collection unit group	Max. 8 units^*4
	Total with remote units connected	Max. 72 units^*5
Continuous acquisition speed	Master data collection unit group	Max. 100 kHz for all acquisition channels ^*6
	Total with remote units connected	Max. 500 kHz for all acquisition channels ^6^7
Inter-unit synchronization	Between measurement units in the master data collection unit group	±1 μs or less ^*8
	Between the master data collection unit and each remote unit / environment-resistant measurement unit
Time axis accuracy		±50 ppm (23°C ±3°C 73.4°F ±5.4°F); Same time used for all remote groups, SNTP server time synchronization possible
Synchronous trigger input (SYNC input)	Performance specifications	• Use as external trigger input (normal mode) or synchronous acquisition input (logging mode) • Non-voltage (contact/non-contact)/voltage input, Falling edge input • Not insulated from system bus
	Input specifications	• For non-voltage input: ON voltage 1.0 V or lower (short circuit current: 1 mA typ.), OFF current 0.1 mA or lower • For voltage input: ON voltage (Lo) 1.0 V or lower, OFF voltage (Hi) 2.4 V or more, Max. input voltage: 6 V
Control input	Common specifications	• Input type: Bidirectional voltage input • Maximum rating: 30 VDC, Minimum ON voltage: 10 VDC, Maximum OFF current: 0.2 mA • Insulation between input and system bus (500 VDC/1 minute)
	Individual specifications	• External trigger input (TRG IN): Edge input • Acquisition start/stop input (START IN): Level input (only enabled in external control mode) • Auto-balance input (BAL): Edge input (only enabled in external control mode) • Program selection input 0 to 3 (PROG IN0 to 3): Level input (only enabled in external control mode)
Control output	Common specifications	• Output format: Photo MOS relay output • Maximum rating: 36 VDC, Output current: 50 mA or less (9-point total: 300 mA or less) • Leak current at OFF: 0.1 mA or less, Residual voltage when ON: 1 V or less • Insulation between output and system bus (500 VDC/1 minute)
	Individual specifications	• Trigger output (TRG OUT): N.O. output, one-shot output • System error output (SYS ERR): N.C. output • Alarm output (ALARM): N.O. output • Judgment output 1 to 4 (OUT1 to 4): N.O. output • Ready output (READY): N.O. output
Power supply		• NR-XU1 AC adapter, or 9 to 36 VDC (including ripple) / Max. 72 W (when connected to DC terminal block; at 9 V: 8.0 A or less; at 24 V: 3.0 A or less; at 36 V: 2.0 A or less) • Battery operation possible when connected to the NR-XU15 Series battery power supply unit
Power supply	Power consumption	8.4 W or less (excluding connected units)
Environmental resistance	Ambient temperature	0 to +40°C 32°F to 104°F
	Relative humidity	10 to 85% RH (no condensation)
Weight		Approx. 490 g 17.30 oz (including approx. 10 g 0.35 oz for the OP-88512 (NR-X100W I/O terminal block))
^1 Data is not backed up when the power is turned off. The available data buffer memory per NR-X100W and NR-XR01 group is limited to 25M. ^2 Use only products recommended by KEYENCE (CA-SD4G: 4 GB, CA-SD16G: 16 GB). Using a product not recommended by KEYENCE may result in data not being saved to the SD card during continuous acquisition. ^3 Wired LAN and wireless LAN cannot be used at the same time. When acquiring data from a PC (using WAVE LOGGER X software), use a wired local connection only between the NR-X100W and the PC. Using an onsite local network connection or wireless LAN connection may cause acquisition to stop due to a decrease in transfer speeds caused by network load or wireless LAN communication conditions. The main unit’s automatic saving function allows data to be saved to an SD card in the main unit even if acquisition by PC stops. ^4 Use is permitted only if the total power consumption of all connected measurement units is 20 W or less. ^5 Use is permitted only if the total power consumption of all measurement units, remote units, and environment-resistant measurement units used in the system is 50 W or less when remote units are not connected to an AC adapter. ^6 Acquisition from a PC may not be possible in some PC environments. [Tested conditions] OS: Windows 10 Pro (64 bit), CPU: 3.70 GHz, RAM: 16.0 GB, USB connections: One NR-X100W (no other USB devices), Ethernet connection: One-to-one connection between NR-X100W and PC; Using normal mode and saving in the standard format with a pre-installed OS and running only WAVE LOGGER X. Windows is a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. ^7 Each master data collection unit group and remote unit group is limited to 100 kHz for all acquisition channels. When using 5 or more remote units, each remote unit group can have up to 50 kHz per acquisition channel. ^8 The sampling cycle and sampling timing vary depending on the connected measurement unit. When using the NR‑CA04 in combination with other unit types, a sampling delay may occur between the NR-CA04 and the other units with some setting configurations.

Keyence SV-C5F Keyence

$0.00

Sold Out

Specifications

Model				SV-C5F
Type				Motor power cable, Standard
Length				5 m 16.4'
Note				for 3 kW / 5 kW motor

Keyence OP-83202 Keyence

$0.00

Sold Out

Specifications

Model				OP-83202
Overview				Front protective cover protecting detection side of light curtain.
Applicable product				SL-V88H, SL-V44L
Number included				1 pcs.
Length				1,750.2 mm 68.91"
Material				Translucent plastic: Polycarbonate Black plastic: ABS
Note				To install this product on both the transmitter and receiver, 2 sets are required. Use the dimming filters (sold separately) by attaching them to the front protection cover. When the front protection cover is attached, the L-shaped mounting bracket (OP-42

Keyence OP-84298 Keyence

$0.00

Sold Out

Specifications

Model				OP-84298
Type				exchange central supports
Applicable product				SJ-H

Keyence CL-PT010N Keyence

$0.00

Sold Out

Specifications

Model				CL-PT010N
Type				Optical unit
Head				CL-PT010 ^*1
Reference distance				10 mm 0.39"
Reference measurement range	Measurement range			±0.3 mm ±0.01"
	Linearity			±0.22 μm ±0.000009" ^*2
High precision measurement range	Measurement range			±0.15 mm ±0.01"
	Linearity			±0.2 μm ±0.000008" ^*2
Resolution				0.25 μm 0.000010" ^*3
Spot diameter				ø3.5 μm ø0.000138"
Laser class	Optical unit			Class I
Sampling cycle				100/200/500/1000 μs (Adjustable 4-stage)
Environmental resistance	Enclosure rating	Head		IP64 (IEC60529)
	Ambient light			Target surface illuminance: 30000 lux (Incandescent lamp)
	Operating ambient temperature	Head		0 to 50°C 32 to 122°F
		Optical unit
	Relative humidity			85% RH or less (no condensation)
	Vibration resistance	Head		10 to 57 Hz, double amplitude 0.45 mm 0.02" 2 hours each for X, Y, and Z axes
		Optical unit		10 to 57 Hz, double amplitude 0.3 mm 0.01"; 2 hours each for X, Y, and Z axes
	Shock resistance			15 G, 6 ms
	Vacuum			None
	Explosion-proof	performance	Head
			Optical unit
		Zone/Division	Head
			Optical unit
		Ambient temperature	Head
			Optical unit
		Certification number
Temperature characteristic	Head			0.1% of F.S./°C ^*4
	Optical unit			0.015% of F.S./°C
Material	Head			Front: SUS, Rear: Aluminum
	Optical unit			Polycarbonate
Weight	Head			Approx. 1100 g 2.43 lb
	Optical unit			Approx. 1600 g 3.53 lb
^1 Sensor head and optical unit are a matched pair. Not cross compatible. ^2 Value measured in displacement mode with KEYENCE reference workpiece (mirrored surface). ^3 Value measured using 16,384 average cycles with KEYENCE reference workpiece (mirrored surface). ^4 These figures are based on the case where a jig made of SUS303 (or SUS304) is fixed between the head and the object.

Keyence SZ-V32NCX Keyence

$4,970.00

Only 6 units left

Specifications

Model				SZ-V32NCX ^*1
Type				Network Type (CIP Safety)
Detection capability	Minimum detectable object size			Diameter 20, 30, 40, 50, 70, 150 mm 0.79", 1.18", 1.57", 1.97", 2.76", 5.91" (depends on the setting) Reflectance 1.8% min., Speed 1.6 m/s 5.25 ft/s max. ^*2
	Detectable angle			190° ( -5° to 185° )
	Response time (ON to OFF)	Standard Mode	Scan Cycle A	160 ms (2scans) to 1280 ms (16scans) ^3 ^4
			Scan Cycle B	168 ms (2scans) to 1344 ms (16scans) ^3 ^4
			Scan Cycle C	176 ms (2scans) to 1408 ms (16scans) ^3 ^4
		High Speed Mode	Scan Cycle A	80 ms (2scans) to 640 ms (16scans) ^3 ^4
			Scan Cycle B	84 ms (2scans) to 672 ms (16scans) ^3 ^4
			Scan Cycle C	88 ms (2scans) to 704 ms (16scans) ^3 ^4
	Response time (OFF to ON)			Response time (ON to OFF) + 150 ms
	Protection zone	Minimum detectable object size: 70 / 150 mm 2.76" / 5.91"		8.4 m 27.56' (Standard Mode) 5.7 m 18.70' (High Speed Mode)
		Minimum detectable object size: 50 mm 1.97"		5.6 m 18.37' (Standard Mode) 3.8 m 12.47' (High Speed Mode)
		Minimum detectable object size: 40 mm 1.57"		4.3 m 14.11' (Standard Mode) 2.9 m 9.51' (High Speed Mode)
		Minimum detectable object size: 30 mm 1.18"		2.9 m 9.51' (Standard Mode) 2.0 m 6.56' (High Speed Mode)
		Minimum detectable object size: 20 mm 0.79"		1.6 m 5.25' (Standard Mode) 1.1 m 3.61' (High Speed Mode)
	Warning zone	Minimum detectable object size: 70 / 150 mm 2.76" / 5.91"		26 m 85.30' (Standard Mode) 23 m 75.46' (High Speed Mode) ^*5
		Minimum detectable object size: 50 mm 1.97"		25 m 82.02' (Standard Mode) 21 m 68.90' (High Speed Mode) ^*5
		Minimum detectable object size: 40 mm 1.57"		24 m 78.74' (Standard Mode) 20 m 65.62’ (High Speed Mode) ^*5
		Minimum detectable object size: 30 mm 1.18"		23 m 75.46' (Standard Mode) 18 m 59.06' (High Speed Mode) ^*5
		Minimum detectable object size: 20 mm 0.79"		21 m 68.90' (Standard Mode) 15 m 49.21' (High Speed Mode) ^*5
	Additional safety distance			100 mm 3.94" ^*6
	Maximum measurement distance			60 m 196.85' ^*7
Maximum number of banks				Max.16 banks
Multiple scanner heads				Max. 3 scanner heads
Camera monitoring area				Monitor area: over 190° (-5° to 185°) ^*8
Display				QVGA 2.2inch color LCD
Light source	Type, wavelength			Infrared laser diode, 905 nm
	Laser Class	IEC		Class1 IEC/EN60825-1
		FDA		Class1 FDA 21CFR 1040.10, 1040.11 (Laser Notice) ^*9
		JIS		Class1 JIS C6802
Control output (OSSD)	Output			-
	Number of outputs
	Max. load current
	Residual voltage (during ON)
	OFF-state voltage
	Leakage current
	Max. capacitive load
	Load wiring resistance
Inputs	PNP
	NPN
Non-safety related output (AUX output)	Output type
	Number of outputs
	Max. load current
	Residual voltage (during ON)
	Muting lamp
Interface	USB			USB2.0
	Ethernet	Standard		IEEE802.3u (100 BASE-TX)
		Transmission rate		100 Mbps
		Cable		STP(Shielded Twisted Pair) cable or UTP(Unshielded Twisted Pair) cable. Category5 or higher.
		Connector		RJ45 (IP65) 2 ports
Network function				CIP Safety, EtherNet/IP™, UDP
Cable length	Power and I/O cable			30 m 98.43' or less ^*10
	Between scanner head and display unitc			20 m 65.62' or less each ^*11
	Ethernet cable			100 m 328.08' or less ^*12
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1 (Type 3 ESPE)
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 3 ESPE), IEC61496-3, EN61496-3 (Type 3 AOPDDR), IEC61508, EN61508, EN ISO13849-1, 2015 (PLd, Category3), UL508, UL1998, CSA C22.2 No.14, CSA C22.2 No.0.8
Rating	Power consumption			13.4 W
	Power voltage			24 VDC ±10% (Ripple P-P 10% or less): When using a converter power supply, 24 VDC +20%/-30%: When using a battery
Environmental resistance	Enclosure rating			IP65(IEC60529)
	Ambient light			Incandescent lamp: 1500 lux or less ^*13
	Operating ambient temperature			-10 to +50°C 14 to 122°F (No freezing)
	Operating relative humidity			35% to 85% RH (No condensation)
	Storage temperature			-25 to +60°C -13 to +140°F (No freezing)
	Storage relative humidity			35% to 95% RH
	Vibration resistance			10 to 55 Hz, 0.7 mm 0.03" compound amplitude, 20 sweeps each in X, Y, and Z directions
	Shock resistance			100 m/s² 328.08 ft/s² (Approx. 10 G) 16 ms pulse, in X, Y, Z directions 1000 times each axis
Material	Scanner head	Main unit case		Magnesium
		Window		Polycarbonate, PEI
		Indicator part		Aluminum, PES
	Display unit	Case		Magnesium, PPS, Polycarbonate
	System memory			Aluminum, PPE
Weight				Approx. 2300 g
^1 Integrated models include display unit, scanner head, system memory and a connection cable (SZ-VS005). ^2 If the object to be detected moves parallel to the detection plane, SZ-V cannot detect the object moving at speed over 1.6 m/s 5.25 ft/s, regardless of the encoder setting. ^3 The response time, protection zone, and warning zone are affected by the operation mode. ^4 When using PROFIsafe, 6 ms is added to the response time. When using CIP Safety, 10ms is added to the response time. ^5 20% or more reflectance is necessary for the minimum detectable object in the warning zone. ^6 If there is a highly reflective background within 1.5 m 4.92' from the boundary of the protection zone, 200 mm 7.87" must be added as supplementary necessary distance to the protection zone when calculating the minimum safety distance. ^7 Even when using the network data output, the maximum measured output distance is 60 m 196.85'. ^8 Only applicable for the type with a camera. ^9 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^10 10 m 32.81' or less when supplying power from a battery. ^11 When supplying power from a battery, the length of each connection cable should be 10 m 32.81' or less when using two scanner heads, and 5 m 16.40' or less when using three scanner heads. ^12 Distance between SZ-V and Ethernet switch. ^*13 An ambient light source should not be located within ±5° of the detection plane.

Keyence GL-SA20S Keyence

$0.00

Sold Out

Specifications

Model				GL-SA20S
Type				Protection cover Slim type for 20 beam axes
Overview				This protective case protects the main unit from impacts.
Applicable product				GL-S20SH
Number included				1
Length				422.6 mm 16.64"
Material				aluminum
Note				2 each of the following are included: hexagon socket head cap screw (width across flats: 3 mm), washer, and special hexagon socket head cap screw (M4, length: 13 mm, width across flats: 3 mm).
Weight				140 g

Keyence SH-302 Keyence

$546.59

Only 2 units left

Specifications

Model		SH-302^*1
Type		Standard Shielded Cylindrical
Shape		ø2.8×12 Cylindrical
Detectable object		Ferrous metal (see Characteristics for nonferrous metals)
Standard target (iron, t=1 mm 0.04")		5 x 5 mm 0.20"^*2
Stable detecting range		0 to 0.6 mm 0.02"
Maximum detecting distance		1.6 mm 0.06"
Repeatability		0.001 mm 0.00004"^*2
Hysteresis		0.03 mm 0.001"^*2
Temperature characteristics		0.3%/°C^*2
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 30 g
^1 The SH-302 cannot be used in combination with the EG-547. ^2 Above values obtained when the detecting distance is set at 50% of the maximum stable detecting distance.

Keyence FU-21 Keyence

$0.00

Sold Out

Specifications

Model		FU-21
Detecting method		Diffuse Reflective
Size		M3
Detection arrangement		Coaxial
Fibre unit length		50 cm19.685" cannot be cut
Shape		Straight
Minimum bend radius		R25 mm0.984"
Detection distance		7 mm0.276"^*1
Environmental resistance	Ambient temperature	-40 to +70 °C -40 to 158 °F
Weight		Approx. 4 g
^*1 The detecting distance is a value for white mat paper (the standard detection object) detections.

Keyence SC-S11 Keyence

$902.09

Only 7 units left

Specifications

Model			SC-S11
Response time			25 ms (safety output ON to OFF, IEC/EN60204-1 stop category 0), 70 ms (safety output OFF to ON)
Safety output (S-OUTPUT)	Output		Two PNP outputs
	Max. load current		500 mA
	Residual voltage (when ON)		2.5 V maximum (with a load current of 500 mA)
	Leakage current		1.2 mA maximum
	Max. capacitive load		2.2 µF (with a load resistance of 100 Ω)
	Load wiring length		30 m maximum
Safety input (S-INPUT, enable input)	Input type		Contact output device connection or PNP output device connection
	Short-circuit current		Approx 5mA
	ON/OFF voltage		Voltage when product turned on: 19 V or more, voltage when product turned off: 5 V or less
	Wiring length		30 m maximum
Safety related input	Input type		Non-voltage contact input (EDM input, reset input)
	Short-circuit current		EDM input: Approx. 10 mA, Reset input: Approx. 5 mA (EDM input, reset input)
	Wiring length		30 m max. (EDM input, reset input)
Non-safety output	Output		PNP/NPN totem pole output (auxiliary output, lockout output)
	Max. load current		50mA (auxiliary output, lockout output)
	Load wiring length		10 m maximum (auxiliary output, lockout output)
Non-safety input	Input type		No-voltage contact input or PNP or NPN open-collector input (external off input)
	Short-circuit current		Approx 5mA (external off input)
	ON/OFF voltage		Voltage when product turned on: 5 V or less or 19 V or more, voltage when product turned off: open or 9 V to 15 V (external off input)
	Wiring length		10 m maximum (external off input)
Protection circuit			Power supply reverse polarity protection, overcurrent protection for each output, short-circuit protection , surge protection
Approved standards	EMC	EMS	IEC 61496-1, EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part 15 Class A, ICES-003 Issue 4 Class A
	Safety		ISO13849-1:2015 (category 4, PLe), UL1998, IEC/EN61496-1, UL508,^*1
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		1.3 A (at maximum load)
Environmental resistance	Enclosure rating		IP20 (IEC60529) Must be installed within a control panel rated at IP54 or higher.
	Pollution degree		2 (IEC60664/EN50178)
	Overvoltage category		2 (IEC60664, EN50178)
	Insulation resistance		100 MΩ or more (tested with a 500 VDC megger) between the internal circuit and the external case
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		35 to 85 % RH (No condensation)
	Storage temperature		-20 to +65 °C -4 to 149 °F (No freezing)
	Storage relative humidity		35 to 85 % RH
	Withstand voltage		1,500 VAC, 50/60 Hz for 1 minute between the internal circuit and the external case
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Polycarbonate (UL94-V2)
Weight			160 g or less
^*1 The following mark is displayed on the ratings indication label on the side of the main unit to identify it as a UL508-certified product.

Keyence KV-NC32ETP Keyence

$1,110.65

Only 2 units left

Specifications

Model			KV-NC32ETP
Expansion output unit	External connectionmethod		MOSFET (With overcurrent protection function)^1^2
	External connection method		Connector
	Rated load		30 VDC. 0.2 A ^*3
	Leakage current (when output is OFF)		100 μA or less
	Residual voltage (at ON)		0.6 VDC or less
	ON resistance		−
	Common method		32 points/1 common (2 terminals)^4^5
	Response time	OFF to ON	100 μs or less (with a load of 1 mA or more)
		ON to OFF	200 μs or less (with a load of 1 mA or more)
	Relay life		−
	Relay replacement
Internal current consumption			50 mA or less
Weight			Approx. 110 g
^1 If even a single overcurrent is detected, the protection operation (output turned OFF) and automatic recovery are repeated for all outputs within the shared common (The outputs within the shared common that are protected when an overcurrent is detected are outputs 000 to 015 or 100 to 115 for the KV-NC32ET(P).) , until the cause of the problem is removed. ^2 MOSFET (N-ch) output for the sink output type; and MOSFET (P-ch) output for the source output type. ^3 The rated load per common terminal is 1.6 A for the KV-NC16ET(P) or KV-NC32ET(P) and 3.2 A for the KV-NC16ET(P)E. ^4 The COM terminals of the KV-NC16ET(P), KV-NC16ET(P)E and KV-NC32ET(P) are shorted internally. ^*5 The outputs within the shared common that are protected when an overcurrent is detected are outputs 000 to 015 or 100 to 115 for the KV-NC32ET(P).

Keyence SJ-F2000 Keyence

$10,799.99

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GL-R44HG Keyence

$4,490.54

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence LV-11SA Keyence

$257.51

Only 9 units left

Specifications

Model			LV-11SA
Type			Main unit
Main unit/expansion unit
Applicable model			LV-S61/S41/S41L/S31/S71/S72
Control output			NPN open-collector × 2 channels, 40 VDC maximum, 100 mA or less per output
Response time	ExceptLV-S31	ULTRA	4 ms
		SUPER	2 ms
		TURBO	500 µs
		FINE	250 µs
		HSP	80 µs
	LV-S31standard mode		500 µs
	LV-S31standard mode	SPED2	2 ms
		SPED3	8 ms
		SPED4	32 ms
	LV-S31High-speed mode		250 µs
Control input			Light emission stop input, external calibration, set value bank selection input, or received light intensity shift input
Number of interference prevention units	ULTRA		―
	SUPER
	TURBO
	FINE
	HSP
Unit expansion
Rating	Power voltage		12 to 24 VDC, Ripple (P-P) 10 % or less, Class2^*1
	Power consumption	Normal	1.5 W or less (62.5 mA or less at 24 V)
		Eco-Half Eco-All	1.35 W or less (57.3 mA or less at 24 V)
Environmental resistance	Ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)^*2
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Main unit		Main body, cover: Polycarbonate
Weight			Approx. 80 g (including 2 m 6.6' cable)
^1 When more than 8 units connected, be sure to use supply voltage 24 VDC Ripple (P-P) 10 % or less ^2 To connect several units they must be mounted on a METAL DIN rail. Ensure that the output current is 20 mA max. With several units connected, the allowable ambient temperature range varies as follows: 1 to 2 units connected: -10 to +55 °C 14 to 131°F, 3 to 10 units connected: -10 to +50 °C 14 to 122°F, 11 to 16 units connected: -10 to +45 °C 14 to 113°F

Keyence OP-88507 Keyence

$0.00

Sold Out

Specifications

Model				OP-88507
Type				High-flex
Sensor Side				M8 4-Pin Straight
Cable Connector				Loose wires
Length				10 m 32.8'
Material				Cable: PVC, Connector: Nickel-plated brass
Weight				Approx. 370 g

Keyence OP-87287 Keyence

$0.00

Sold Out

Specifications

Model				OP-87287
Overview				O-ring used between the sensor main body of GP-M Series and the adapter.
Applicable product				GP-M001/M010/M025
Number included				1 pcs.
Material				FKM

Keyence OP-89057 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SI-F1001 Keyence

$0.00

Sold Out

Specifications

Model			SI-F1001^*1
Type			Main Controller Separate type^*2
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec.
Terminal block	Laser remote interlock input		Non-voltage input^*3
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*3
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*3
	Alarm output		NPN open-collector output (N.C.)^*3
	General comparator output		NPN open-collector output^*3
Expansion connector	TIMING2 input		Non-voltage input^*3
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*3
	Alarm output		NPN open-collector output (N.C.)^*3
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*3
		Strobe output	NPN open-collector output^*3
		Binary selection output
		Binary selection input	Non-voltage input^*3
RS-232C interface			Measured data output and control input/output (Baud rate selectable to 115,200 bps max.)
USB interface			USB 2.0 high speed compliant (USB 1.1 Full-SPEED compatible)
Ethernet interface			100Base-TX/10Base-T
Major functions			12 Out simultaneous measurement calculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory, interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*4
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 The SI-F1003 can be used independently, The measured value display and setting change can be done with the display panel(SI-FD500) and setup support software(SI-H3). ^2 The SI-F1001 can be used independently. The measured value display and setting change can be done with the display panel (SI-FD500) and setup support software (SI-H1). ^3 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^4 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence GL-SA32F Keyence

$0.00

Sold Out

Specifications

Model				GL-SA32F
Type				Protection cover Flat type for 32 beam axes
Overview				This protective case protects the main unit from impacts.
Applicable product				GL-S32FH
Number included				1
Length				662.6 mm 26.09"
Material				aluminum
Note				2 each of the following are included: hexagon socket head cap screw (width across flats: 3 mm), washer, and special hexagon socket head cap screw (M4, length: 13 mm, width across flats: 3 mm).
Weight				210 g

Keyence OP-82488 Keyence

$0.00

Sold Out

Specifications

Model				OP-82488
Type				Power cable
Applicable product				FT Series
Length				2 m 6.56'
Note				Included with amplifier
Weight				Approx. 55 g

Keyence OP-88651 Keyence

$0.00

Sold Out

Specifications

Model				OP-88651
Type				M12/M12 Ethernet cable
Length				2 m 6.6'
Weight				約 160 g

Keyence OP-84296 Keyence

$0.00

Sold Out

Specifications

Model				OP-84296
Type				Relay Box

Keyence GL-R23F Keyence

$750.80

Only 8 units left

Specifications

Model			GL-R23F
Detection capability			ø0.55" ø14 mm
Total length			9.45" 240mm
No. of beam			23
Detection height			8.66" 220mm
Protection height			9.61" 244mm
Beam axis spacing/Lens diameter			10 mm 0.39" / ø4 ø0.16"
Detecting distance			0.66 to 32.81' 0.2 to 10 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	6.9
		OFF→ON	49.2^*2
		All blocked→ON	64.4^*3
	Optical synchronization system (Channel A or B)	ON→OFF	9.3
		OFF→ON	52.7^*2
		All blocked→ON	74^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	50
		Receiver	70
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		320 g
	Receiver		330 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence FU-48 Keyence

$159.62

Only 9 units left

Specifications

Model		FU-48^*1
Size		ø3 mm0.118"
Fibre unit length		2 m78.74" free-cut
Fibre unit diameter		ø1.0×2
Minimum bend radius		R4 mm0.157" high-flex
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +70 °C -40 to 158 °F
Weight		Approx. 7 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.