MP-FR10 Keyence

Specifications

Model		MP-FR10
Type		Single model
Connection bore diameter		Rc3/8" (10 A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─
	Filtration degree
	Drainage cup capacity
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

Est. delivery between and

$622.25

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: MP-FR10-Sealed

Sold out

$0.00

Never Used Surplus

SKU: MP-FR10

2 verified stock

$622.25

Used

SKU: MP-FR10-Used

Sold out

$0.00

Variant

Quantity:

Need More?

Specifications

Model		MP-FR10
Type		Single model
Connection bore diameter		Rc3/8" (10 A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─
	Filtration degree
	Drainage cup capacity
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

Model		MP-FR10
Type		Single model
Connection bore diameter		Rc3/8" (10 A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─
	Filtration degree
	Drainage cup capacity
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator