Vision Systems

Keyence OP-87930 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CA-LH50P Keyence

$1,154.45

Only 3 units left

Specifications

Model				CA-LH50P
Focal point				50 mm 1.97"
F-stop range (aperture)				F2.8/4/8/16^*1
Minimum WD				0.2 m 0.7'
Filter size				27.0 mm 1.06" P0.5
Mount				C-mount
Max. compatible image sensor size				2/3"
Resolving power				100 cycles/mm at center, 80 cycles/mm on periphery
TV distortion				-0.03％ (-0.01％)^*2
Enclosure rating				IP64 (objective lens, water repellent coating specifications)^*3
Ambient temperature/humidity range				0 to +50°C 32 to 122°F, 80% RH or less (No condensation)
Weight				Approx. 85 g
^1 The f-stop (aperture) is changed by replacing the diaphragm plate. When this product is shipped, the OPEN diaphragm plate is attached to the lens, so replace it with one of the other included diaphragm plates (F4, F8, or F16) as necessary. To use the f-stop (aperture) in the OPEN mode, use the lens without removing the OPEN aperture. ^2 This indicates the value with the maximum supported image size. The value in parentheses applies to a 1/3" image sensor size. ^*3 When connected to a KEYENCE environmentally resistant camera (excluding when the close-up ring and filter are attached)

Keyence HC-50 Keyence

$2,644.67

Only 8 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SV2-C10CG Keyence

$0.00

Sold Out

Specifications

Model				SV2-C10CG
Type				Motor power cable, Hi-flex robotic cable
Length				10 m 32.8'
Note				for 750 W motor

Keyence EH-416 Keyence

$225.17

In stock, 54 units

Specifications

Model		EH-416
Type		Standard , Non-shielded , Cylindrical and threaded
Detectable object		Ferrous metals (see Characteristics for nonferrous metals)
Standard target (iron, t=1 mm 0.04")		20 x 20 mm 0.79" x 0.79"
Stable detecting range		0 to 6 mm0.24"
Maximum detecting distance		13 mm0.51"
Hysteresis		0.05 mm0.002"
Repeatability		0.012 mm0.0005"
Temperature characteristics		±10% max. of detecting distance at 23°C 73.4°F, within -10 to +60°C 14 to 140°F
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 72 g (including nuts and 3-m 9.8' cable)

Keyence BL-180S0 Keyence

$920.93

Only 3 units left

Buy the Keyence BL-180S0 - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence BL-180S0 is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence OP-51625 Keyence

$0.00

Sold Out

Specifications

Model				OP-51625
Overview				Bottom-mounting bracket for the MS2-H50. This is used when directly fastening the main unit with screws.
Applicable product				MS2-H50
Weight				Approx. 79 g

Keyence ER-GM12P03C Keyence

$0.00

Sold Out

Specifications

Model		ER-GM12P03C
Type		General-purpose all-metal shielded type Screw type M12 Connector with pigtail (M12 4-pin) PNP output Mid-Range
Power supply cable length		0.3 m 1.0' ^*1
No. of control outputs		2
Output mode	Output 1	N.O.
	Output 2	N.C.
Button		None
Button	Function	―
Detecting distance		4 mm 0.16" ±10% ^*2
Response frequency		150 Hz ^3 ^4
Hysteresis distance		15% or less of detecting distance
Detectable object		Magnetic metal, Non-magnetic metal ^*5
Standard detectable object (Iron, t = 1 mm 0.04")		12 × 12 mm 0.47" × 0.47"
Temperature characteristics		±10% or less of detecting distance at +25°C +77°F (-25 to +55°C -13°F to +131°F) ±15% or less of detecting distance at +25°C +77°F (+55 to +70°C 131°F to 158°F)
Control output		Open-collector, 30 VDC or less; 50 mA or less for 1 output; 50 mA or less in total for 2 outputs
Control output	Residual voltage	PNP output: 2.2 V or less (Output current: 10 mA or less) / 2.3 V or less (Output current: 10 to 50 mA) ^*6
Power supply	Power voltage	16 to 30 VDC (including 10% or less ripple (P-P)), Class 2
	Power consumption (excluding load current)	1000 mW or less (42 mA or less at 24 V, 63 mA or less at 16 V)
Protection circuit		Protection against reverse power connections, output short-circuits, and reverse output connections
Environmental resistance	Enclosure rating	IP67 (IEC60529), IP67G (JIS C 0920)
	Ambient temperature	-25 to +70°C -13°F to +158°F (no freezing) ^*7
	Relative humidity	Up to 95% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	1000 m/s² 3280.8 ft/s² (100 G), 10 times in each of the X, Y, and Z directions
Material		Detecting surface: SUS303, Mounting screw: SUS303, Case resin: PBT, Nut: SUS304, Toothed lock washer: SUS304 [Connector] Indicator: PBT (M8: LCP), Connector: PBT (M8: LCP), Case: SUS303 [Connector with pigtail] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC, Connector resin: TPU, Connector metal: Nickel-plated brass [Cable] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC
Accessories		Nut ×2, Toothed lock washer ×1
Weight		Approx. 50 g 1.77 oz
^1 Ensure the power cable is no longer than 30 m 98.4' for connector and connector with pigtail types. ^2 The distance at which a standard detectable object can be detected when the unit is mounted without being affected by surrounding metal. ^3 Value when a standard detectable object is used, the distance between detectable objects is twice the standard detectable object, and the distance to the detectable object is 1/2 the detecting distance. ^4 The response frequency varies depending on the operating temperature. The response frequency at temperatures of +55°C +131°F or higher is 50% of that at +25°C +77°F. ^5 Detecting distance varies according to the material and size. See the characteristic diagrams for details. ^6 Residual voltage is for when a 2 m 6.6' cable is used. ^*7 The upper limit of the UL temperature rating is +55℃ +131℉.

Keyence OP-91127 Keyence

$0.00

Sold Out

Specifications

Model				OP-91127
Type				Mounting Fittings
Overview				Dedicated mounting bracket for PQ. Transmitter/receiver setup.
Applicable product				PQ-01, PQ-02
Number included				2 pcs.
Material				Steel (Black chromate)

Keyence OP-88150 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CL-V020G Keyence

$0.00

Sold Out

Specifications

Model				CL-V020G
Type				Optical unit
Head				CL-V020 ^*1
Reference distance				20 mm 0.79"
Reference measurement range	Measurement range			±1.3 mm ±0.05"
	Linearity			±0.3 μm ±0.000012" ^*2
High precision measurement range	Measurement range			±0.5 mm ±0.02"
	Linearity			±0.23 μm ±0.000009" ^*2
Resolution				0.01 μm ^*3
Spot diameter				ø20 μm ø0.0008"
Laser class	Optical unit			Class I
Sampling cycle				100/200/500/1000 μs (Adjustable 4-stage)
Environmental resistance	Enclosure rating	Head		IP40 degassed structure for vacuum environments ^*4
	Ambient light			Target surface illuminance: 30000 lux (Incandescent lamp)
	Operating ambient temperature	Head		-20 to 200°C -4 to 392°F
		Optical unit		0 to 50°C 32 to 122°F
	Relative humidity			85% RH or less (no condensation)
	Vibration resistance	Head		10 to 57 Hz, double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
		Optical unit		10 to 57 Hz, double amplitude 0.3 mm 0.01"; 2 hours each for X, Y, and Z axes
	Shock resistance			15 G, 6 ms
	Vacuum			Ultra-high-vacuum environments ^*5
	Explosion-proof	performance	Head	None
			Optical unit
		Zone/Division	Head
			Optical unit
		Ambient temperature	Head
			Optical unit
		Certification number
Temperature characteristic	Head			0.013% of F.S./°C ^*6
	Optical unit			0.015% of F.S./°C
Material	Head			SUS304
	Optical unit			Polycarbonate
Weight	Head			Approx. 100 g 3.53 oz
	Optical unit			Approx. 1600 g 3.53 lb
^1 Sensor head and optical unit are a matched pair. Not cross compatible. ^2 Value measured in displacement mode with KEYENCE reference workpiece (mirrored surface). ^3 Value measured using 16,384 average cycles with KEYENCE reference workpiece (mirrored surface). ^4 The enclosure rating is equivalent to IP50 when the included sticker is attached. ^5 Operation verification has been performed in environments of 10^-6 Pa. ^6 These figures are based on the case where a jig made of SUS303 (or SUS304) is fixed between the head and the object.

Keyence OP-87667 Keyence

$0.00

Sold Out

Specifications

Model				OP-87667
Type				Plate nut for flat
Applicable product				PR-F Series
Number included				2 pcs.
Material				SUS316L
Weight				Approx. 1 g

Keyence KL-8BLX Keyence

$553.50

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FU-32 Keyence

$163.85

Only 9 units left

Specifications

Model		FU-32^*1
Optical axis diameter (Standard target to be detected)		ø0.6 mm0.024"
Beam emitting direction		Side
Fibre unit length		1 m39.37" free-cut
Fibre unit diameter		ø1.3
Minimum bend radius		R25 mm0.984"
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +70 °C -40 to 158 °F
Weight		Approx. 5 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence OP-87908 Keyence

$203.99

Only 6 units left

Specifications

Model				OP-87908
Type				Vertical mounting bracket
Weight				Approx. 20 g

Keyence S-P12 Keyence

$0.00

Sold Out

Specifications

Model				S-P12
Type				Tough mounting bracket
Applicable product				PZ2 Series
Number included				1 unit

Keyence GL-VP2 Keyence

$0.00

Sold Out

Specifications

Model				GL-VP2
Type				Main unit connection cable
Number included				1 pc.
Cable end				Female side: M12 connector 5 pin Male side: Strand wire, 5-core
Number of cores				5
Length				2 m 6.6'
Material				connector: PVC/Nickel-plated brass cable: PVC
Weight				130 g

Keyence DL-EC1A Keyence

$374.06

Only 10 units left

Specifications

Model		DL-EC1A
Ethernet specifications	Compliant standards	IEEE802.3u (100BASE-TX)
	Transmission speed	100 Mbps (100BASE-TX)
	Transmission interface	Category 5e or higher STP cable
	Distance between nodes	100 m 3937.01'
	Communication port	RJ-45 x 2
EtherCAT communication specifications	Compatible functions	Process data object communication (cyclic communication) Mailbox communication (message communication) CoE compatible Explicit Device Identification
	Conformance test version	Complies with V2.0.42
Sensor connection specifications	Connectable sensors	Sensor amplifiers with D-bus support^*1
	Number of connectable sensor units	15 units max.^*2
Indicator lamps		Power indicator (PWR): Green LED RUN indicator (RUN): Green LED ERR indicator (ERR): Red LED Sensor communication indicator (D-bus): 2-color (green/red) LED Link/activity indicator: Green LED
Power voltage		20 to 30 VDC, including ripple (p-p) of 10 % supplied from the connected sensor amplifiers
Power consumption		2,100 mW or less (at 30 V, 70 mA max.)
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit: Polycarbonate
Weight		Approx. 70 g (including connectors)
^1 D-bus is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^2 This varies depending on the connected sensor amplifiers.

Keyence GL-VM06LN Keyence

$0.00

Sold Out

Specifications

Model			GL-VM06LN
Beam axis spacing/Lens diameter			40 mm 1.57": ø5 ø0.197"
Number of beam axes			6
Total length			240 mm 9.45"
Detection height			200 mm 7.87"
Protection height			285 mm 11.22"
Minimum detectable object size			ø45 mm ø1.77" ^*1
Detecting distance			0.3 to 15 m 1.0' to 49.2' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	4.1
		OFF→ON	45.7 ^*3
		All blocked→ON	51.2 ^*4
	With channel A or B	ON→OFF	10.0
		OFF→ON	54.9 ^*3
		All blocked→ON	68.2 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	60 ^*5
		Receiver	73 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	48 ^*5
		Receiver	56 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		170 g 6.00 oz
	Receiver
	Total		340 g 12.00 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence CA-DQR15 Keyence

$0.00

Sold Out

Specifications

Model				CA-DQR15
Type				Square Lights (Direct)
LED color				red
Diffusion plate				OP-87042^*1
Power consumption				14.4 W^*2
Weight				Approx 520 g
^1 The models listed on the left are for a single bar. Four sets are required for the whole square. ^2 Total value of four bars

Keyence GL-R08L Keyence

$809.99

Only 6 units left

Specifications

Model			GL-R08L
Detection capability			ø1.77" ø45 mm
Total length			12.60" 320mm
No. of beam			8
Detection height			11.02" 280mm
Protection height			14.37" 365mm
Beam axis spacing/Lens diameter			40 mm / ø5 1.57" / ø0.20"
Detecting distance			0.66 to 49.21' 0.2 to 15 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	6.6
		OFF→ON	48.7^*2
		All blocked→ON	63.1^*3
	Optical synchronization system (Channel A or B)	ON→OFF	6.9
		OFF→ON	49.1^*2
		All blocked→ON	64.2^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	41
		Receiver	68
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		430 g
	Receiver		440 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence FU-1346 Keyence

$0.00

Sold Out

Buy the Keyence FU-1346 - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence FU-1346 is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence GL-VM191FP Keyence

$0.00

Sold Out

Specifications

Model			GL-VM191FP
Beam axis spacing/Lens diameter			10 mm 0.39": ø4 ø0.16"
Number of beam axes			191
Total length			1920 mm 75.59"
Detection height			1900 mm 74.80"
Protection height			1924 mm 75.75"
Minimum detectable object size			ø14 mm ø0.55" ^*1
Detecting distance			0.3 to 12 m 1.0' to 39.4' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	11.9
		OFF→ON	61.3 ^*3
		All blocked→ON	78.4 ^*4
	With channel A or B	ON→OFF	41.1
		OFF→ON	118.8 ^*3
		All blocked→ON	178.6 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	187 ^*5
		Receiver	213 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	66 ^*5
		Receiver	80 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		1250 g 44.12 oz
	Receiver		1260 g 44.47 oz
	Total		2510 g 88.60 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence CL-P030G Keyence

$0.00

Sold Out

Specifications

Model			CL-P030G
Type			Optical unit
Head			CL-P030 ^*1
Reference distance			30 mm 1.18"
Reference measurement range	Measurement range		±3.7 mm ±0.15"
	Linearity		±0.81 μm ±0.000032" ^*2
High precision measurement range	Measurement range		±1.0 mm ±0.04"
	Linearity		±0.59 μm ±0.000023" ^*2
Resolution			0.015 μm 0.000001" ^*3
Spot diameter			ø38 μm ø0.0015"
Laser class	Optical unit		Class I
Sampling cycle			100/200/500/1000 μs (Adjustable 4-stage)
Environmental resistance	Enclosure rating	Head	IP67 (IEC60529)
	Ambient light		Target surface illuminance: 30000 lux (Incandescent lamp)
	Ambient temperature		0 to 50°C 32 to 122°F
	Relative humidity		85% RH or less (no condensation)
	Vibration resistance	Head	10 to 57 Hz, double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
		Optical unit	10 to 57 Hz, double amplitude 0.3 mm 0.01"; 2 hours each for X, Y, and Z axes
	Shock resistance		15 G, 6 ms
Temperature characteristic	Head		0.005% of F.S./°C
	Optical unit		0.015% of F.S./°C
Material	Head		Front: SUS, Rear: Aluminum
	Optical unit		Polycarbonate
Weight	Head		Approx. 200 g 7.06 oz
	Optical unit		Approx. 1600 g 3.53 lb
^1 Sensor head and optical unit are a matched pair. Not cross compatible. ^2 Value measured in displacement mode with KEYENCE reference workpiece (mirrored surface) . ^*3 Value measured using 16,384 average cycles with KEYENCE reference workpiece (mirrored surface).