Sensors & Detection

Omron R7M-A40030-S1 Omron

$4,544.00

Only 6 units left

AC Motor Servomotor, 3000 RPM, 400W, Incremental, 230VAC

Keyence LV-N11P Keyence

$293.70

Only 9 units left

Specifications

Model		LV-N11P
Type		2 output
Output		PNP
Cable/connector		Cable
Main/Expansion unit		Main unit
I/O	Control outputs	2 output
	External input	1 input
	Monitor output	None
Output selection		LIGHT-ON/DARK-ON (switch-selectable)
Timer function		Timer OFF/OFF-delay timer/ON-delay timer/One-shot timer, Timer duration selectable: 1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.
Control outputs		PNP open collector 30 V, Residual voltage 1.2 V or less (Output current: 10 mA or less) / 2.2 V or less (Output current: 10 to 100 mA) (Stand-alone) 1 output max: 100 mA or less, 2 output total: 100 mA or less (Multiple connections) 1 output max: 20 mA or less
Response time		80 µs (HIGH SPEED)/250 µs (FINE)/500 µs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA) ^*1
Monitor output		-
External input		Input time 2 ms (ON)/20 ms (OFF) or more^*2
Number of interference prevention units		Connected to other than LV-S31: 0 for HIGH SPEED; 2 for FINE/TURBO/SUPER; 4 for ULTRA/MEGA, Connected to LV-S31: 2 for FINE; 4 for TURBO/SUPER/ULTRA/MEGA^*3
Case size		H 32.6 mm 1.28" × W 9.8 mm 0.39" × L 78.7 mm 3.1"
Unit expansion		Up to 17 units can be connected in total (two-output type is treated as two units)
Protection circuit		Reverse polarity protection, Over-current protection, Surge absorber
Rating	Power voltage	24 VDC (operating voltage 10 to 30 VDC (with ripple)), Ripple (P-P) 10 % or less, Class 2 or LPS^4^5
	Power consumption	Normal: 950 mW or less (at 30 V. 33 mA at 24 V, 60 mA or less at 12 V)^6 Eco on mode: 815 mW or less (at 30 V. 29 mA at 24 V, 52 mA or less at 12 V)^6 Eco Full mode: 650 mW or less (at 30 V. 24 mA at 24 V, 40 mA or less at 12 V) ^*7
Environmental resistance	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)^*8
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material	Cable	PVC
	Case	Main unit and cover material: Polycarbonate
Weight		Approx. 75 g
^1 80 µs cannot be selected when the LV-S31/S62/S63 is connected ^2 Input time is 25 ms (ON)/25 ms (OFF) when external calibration time is selected. ^3 These numbers double when "DOUBLE" is selected. ^4 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^5 To connect more than 9 units, the power voltage must be 20 V or more. ^6 Increases 30 mW (1 mA) for HIGH SPEED mode. ^7 It increases by 15% when connected to the LV-NH100/NH110/NH300. It does not include the power consumption of the load. Power consumption when expansion units are connected is the total power consumption of each amplifier unit. Example: When one main unit (LV-N11N) is connected to 2 expansion units (LV-N12N) and they are used with LV-NH100 heads in HIGH SPEED mode. (1.15 × 860 mW × 1) + (1.15 × 860 mW × 2) = 2967 mW max. ^8 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less for a unit. One or two more units connected: -20 to +55 °C -4 to 131 °F; 3 to 10 more units connected: -20 to +50 °C -4 to 122 °F; 11 to 16 more units connected: -20 to +45 °C -4 to 113 °F. When using 2-outputs, one unit is counted as two units.

Keyence LK-G5001 Keyence

$1,872.36

Only 10 units left

Specifications

Model		LK-G5001
Type		Separate type Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	0.001 µm
	Display range	±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle	Approx 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω^*1
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω^*1
	No. of analog outputs	2^*1
	TIMING 1 input	Non-voltage input^*2
	RESET 1 input
	Auto-zero 1 input
	Laser remote input	Non-voltage input^*1
	Alarm output	NPN open-collector output^*1
	General comparator output
Expansion connector	TIMING input	Non-voltage input^*1
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output^*1
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9600 to 115200 bps Data length: 8 bits Stop bit length: 1 bit Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*3
Ethernet interface		100Base-TX/10Base-T^*4
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*5
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10%
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^2 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. This input is applied to all of the synchronized OUT. ^3 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^4 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*5 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Keyence FS-N18N Keyence

$130.56

In stock, 43 units

Keyence FS-N18N Digital Fiber Optic Sensor, Fiber Amplifier

Omron NJ501-1400 Omron

$2,878.08

Only 7 units left

Sysmac NJ5 CPU 20MB memory built-in EtherCAT (32 servo axes in total 192 EtherCAT nodes) and EtherNet/IP

Omron NX502-1300 Omron

$3,367.03

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Omron NX-SL3300 Omron

$501.98

In stock, 16 units

Safety controller 32 safety master connections up to 256 safety I/O

Omron OS32C-BP-4M Omron

$6,571.46

Only 3 units left

Safety laser scanner, safety radius 4 m, warning zone 15 m, PLd & Cat 3, 24 VDC, back location cable exit

Keyence LV-N12P Keyence

$305.76

Only 7 units left

Specifications

Model		LV-N12P
Type		2 output
Output		PNP
Cable/connector		Cable
Main/Expansion unit		Expansion unit
I/O	Control outputs	2 output
	External input	1 input
	Monitor output	None
Output selection		LIGHT-ON/DARK-ON (switch-selectable)
Timer function		Timer OFF/OFF-delay timer/ON-delay timer/One-shot timer, Timer duration selectable: 1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.
Control outputs		PNP open collector 30 V, Residual voltage 1.2 V or less (Output current: 10 mA or less) / 2.2 V or less (Output current: 10 to 100 mA) (Stand-alone) 1 output max: 100 mA or less, 2 output total: 100 mA or less (Multiple connections) 1 output max: 20 mA or less
Response time		80 µs (HIGH SPEED)/250 µs (FINE)/500 µs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA) ^*1
Monitor output		-
External input		Input time 2 ms (ON)/20 ms (OFF) or more^*2
Number of interference prevention units		Connected to other than LV-S31: 0 for HIGH SPEED; 2 for FINE/TURBO/SUPER; 4 for ULTRA/MEGA, Connected to LV-S31: 2 for FINE; 4 for TURBO/SUPER/ULTRA/MEGA^*3
Case size		H 32.6 mm 1.28" × W 9.8 mm 0.39" × L 78.7 mm 3.1"
Unit expansion		Up to 17 units can be connected in total (two-output type is treated as two units)
Protection circuit		Reverse polarity protection, Over-current protection, Surge absorber
Rating	Power voltage	24 VDC (operating voltage 10 to 30 VDC (with ripple)), Ripple (P-P) 10 % or less, Class 2 or LPS^4^5
	Power consumption	Normal: 950 mW or less (at 30 V. 33 mA at 24 V, 60 mA or less at 12 V)^6 Eco on mode: 815 mW or less (at 30 V. 29 mA at 24 V, 52 mA or less at 12 V)^6 Eco Full mode: 650 mW or less (at 30 V. 24 mA at 24 V, 40 mA or less at 12 V) ^*7
Environmental resistance	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)^*8
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material	Cable	PVC
	Case	Main unit and cover material: Polycarbonate
Weight		Approx. 65 g
^1 80 µs cannot be selected when the LV-S31/S62/S63 is connected ^2 Input time is 25 ms (ON)/25 ms (OFF) when external calibration time is selected. ^3 These numbers double when "DOUBLE" is selected. ^4 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^5 To connect more than 9 units, the power voltage must be 20 V or more. ^6 Increases 30 mW (1 mA) for HIGH SPEED mode. ^7 It increases by 15% when connected to the LV-NH100/NH110/NH300. It does not include the power consumption of the load. Power consumption when expansion units are connected is the total power consumption of each amplifier unit. Example: When one main unit (LV-N11N) is connected to 2 expansion units (LV-N12N) and they are used with LV-NH100 heads in HIGH SPEED mode. (1.15 × 860 mW × 1) + (1.15 × 860 mW × 2) = 2967 mW max. ^8 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less for a unit. One or two more units connected: -20 to +55 °C -4 to 131 °F; 3 to 10 more units connected: -20 to +50 °C -4 to 122 °F; 11 to 16 more units connected: -20 to +45 °C -4 to 113 °F. When using 2-outputs, one unit is counted as two units.

Omron CIMR-AC4A0072AAA Omron

$2,248.52

Only 2 units left

A1000 inverter: 3~ 400 V, HD: 30 kW 60 A, ND: 37 kW 72 A

Omron NX-TS3101 Omron

$570.57

Only 7 units left

Controllers NX 4Pt Thermocouple

Omron NX-DA3203 Omron

$399.08

Only 6 units left

Controllers NX 4Pt D/A 4-20m 1/8k 250us/pt

Keyence FD-Q10C Keyence

$544.13

In stock, 11 units

Specifications

Model		FD-Q10C
Supported pipe diameter		1/4" (8 A), ø13 to ø16 (mm) 3/8" (10 A), ø16 to ø18 (mm)
Supported pipe materials		Metal pipe/Resin pipe^*1
Supported fluids		Various liquid [i.e. water (including DI), oils, chemicals, etc.]^*1
Supported fluid temperature		0 to 85°C 32 to 185°F (No freezing on the pipe surface)^*2
Maximum rated flow		1/4" (8 A): 20 L/min, 5.2 G/min 3/8" (10 A): 30 L/min, 7.9 G/min
Zero cut flow rate		1.0 L/min (Default)^*3
Display method		Status indicator, output indicator, dual row display with 4-digit, 7 segment LED, stability level indicator
Display update cycle		Approx. 3 Hz
Display resolution		0.01/0.1/1 (Default : 0.1) (L/min)
Response time		0.5 s / 1.0 s / 2.5 s / 5 s / 10 s / 30 s / 60 s
Protection circuit		Power supply reverse connection protection, power supply surge protection, each output short-circuit protection, each output surge protection
Repeatability		0.5 s : ±2.0%, 1 s:±1.5%, 2.5 s : ±1.0%, 5 s : ±0.5%, 10 s : ±0.35%, 30 s : ±0.2%, 60 s : ±0.15% (/F.S.^*4(Specific to selected response time))
Hysteresis		Variable
Integrated flow unit display		0.1/ 1/ 10/ 100/ 1000 (Default : 1) (L)
Integrated flow data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length: 10 years or longer, Data read/write frequency: 1 million times or more)
Power I/O connector		M12 4-pin connector
Input/Output (Selectable)	Output (ch.1/ch.2)	Control output/ Pulse output/ Error output (Selectable, Default : ch.1 control output/ ch.2 not used), NPN/PNP setting switchable,open collector output 30 V or less, max. 100 mA/ch., residual voltage 2.5 V or less^*5
	Analog output (ch.2)	4 to 20 mA / 0 to 20 mA (Selectable, Default: not used), load resistance 500 Ω or less^*5
	External input (ch.2)	Integrated flow reset input/ Flow rate zero input/ Origin adjustment input (Selectable, Default: not used), short-circuit current 1.5 mA or less, input time 20 ms or more^*5
Power supply	Power voltage	20 to 30 VDC , ripple (P-P) 10% max, Class2/LPS
	Current consumption	100 mA or less (Load current excluded)^*6
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	100 m/s², 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Sensor main unit	PPS/PES/PBT/SUS303/SUS304/SUSXM7
	Sensor surface	Rubber
	Mounting bracket	SUS304/PA/SUSXM7
Weight		Approx. 340 g (including mounting bracket)
^1 Liquid must allow for the passage of an ultrasonic pulse, as well as not contain large air pockets or excessive bubbles. Detection may be unstable on certain non-standard pipes (i.e. lined pipes) ^2 Contact KEYENCE when the temperature of the pipe is greater than 85°C 185°F ^3 The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate. ^4 This specification is valid when the flow velocity distribution is stable. This value does not take into account the effects of pulsation or fluctuations in flow velocity distribution due to facility factors. Convert the F.S. (full scale) listed in the table according to the rated flow range. ^5 IO-Link: Compatible with Specification v1.1 / COM2 (38.4 kbps) The setting file can be downloaded from the KEYENCE website. If using the unit in the environment where downloading the file is not possible via internet, contact your nearest KEYENCE office. IO-Link is either registered trademarks or trademarks of PROFIBUS Nutzerorganisation e.V. (PNO) ^6 When including the loads, please add 200 mA to this value.

Keyence FS-V31CP Keyence

$246.18

In stock, 64 units

Specifications

Model		FS-V31CP
Type		1-output + 1-input with M8 connector
Output		PNP
Main unit/Expansion unit		Main unit
Control output		1 output
Monitor output (1 to 5 V)		N/A
External input		1 input
Connector		M8
Light source LED		Red, 4-element LED (Wavelength: 640 nm)
Response time		33 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER TURBO) /4 ms (ULTRA TURBO) /16 ms (MEGA TURBO)
Output selection		LIGHT-ON/DARK-ON (switch-selectable)
Display indicator		Operation indicator: Red LED/Dual digital monitor: Dual 7-segment display, Preset Value (4-digit green LED indicator) and Current Value (4-digit red LED indicator) illuminated together. Current Value range: 0 to 64,512; Excess gain: 0P to 999P, Hold function: Possible to display both peak and bottom hold values, Selectable from 5 variations Bar LED monitor: Excess gain displayed (85% to 115% in 7 steps), Scaling display
Size		30.3 mm (H) x 9.8 mm (W) x 71.8 mm (D) 1.19" (H) x 0.39" (W) x 2.83" (D)
Detection mode		Light intensity (area detection possible, automatic sensitivity-tracking function provided)
Timer function		OFF-delay timer/ON-delay timer/One-shot timer/ON-delay timer + OFF-delay timer/ON-delay timer + One-shot timer, selectable Timer duration selectable: 0.1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.
Control output		PNP open-collector 24 V, 100 mA max.^*1 (main unit only)/20 mA max. (when the expansion unit(s) is connected), Residual voltage: 1 V max.
External inputy		Input time: 2 ms (ON)/20 ms (OFF) min.^*2
Unit expansion		Up to 16 expansion units can be connected (a total of 17 units). Note that the 2-output type should be counted as two units.
Number of interference prevention units	Normal operation	HIGHSPEED：0 FINE：4 TURBO/SUPER/ULTRA/MEGA：8台
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Power consumption	Normal: 750 mW max. (Using 24 V, 31 mA max., using 12 V, 40 mA max.)/ Power saving 580 mW max. (Using 24 V, 24 mA max., using 12 V, 28 mA max.)^*3
Environmental resistance	Ambient light	Incandescent lamp: 20,000 lux max., Sunlight: 30,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*4
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Accessories		N/A
Weight		Approx. 80 g
^1 Total current of two outputs should be less than 100 mA. ^2 Only available on certain models. ^3 When using the HIGH SPEED mode, the power consumption increases by 160 mW (7 mA). ^4 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less. 1 to 2 Units: -10 to +55 °C 14 to 131 °F, 3 to 10 Units: -10 to +50 °C 14 to 122 °F, 11 to 16 Units: -10 to +45 °C 14 to 113 °F

Balluff BNS005M Balluff

$300.38

Only 4 units left

Balluff BNS Mechanical Position Switch (P/N: BNS005M). Mechanical cam-operated position switch for precise machine positioning, tool change monitoring, and rotary table indexing. Multiple switching positions with roller plunger actuators, IP67 protection, and configurable contact configurations for machine tools, transfer lines, and packaging machinery.

Omron NX-OD5121 Omron

$136.10

In stock, 11 units

I/O Modules NX 16Pt 12-24VDC NPN Trans Out

Omron GX-JC06 Omron

$312.23

Only 10 units left

Ethernet Modules EtherCAT 6 Port Branching Unit

Omron NX-EC0222 Omron

$319.04

Only 7 units left

Controllers NX 2Pt Inc Enc 24V PNP

Omron E3Z-T86 Omron

$97.23

Only 6 units left

Through-beam type, PNP output, Sensing distance 15 m, M8 connector models

Omron S8VK-G12024 Omron

$136.10

Only 7 units left

DIN Rail Power Supplies 120W 24VDC 5A

Keyence LK-G5001V Keyence

$2,253.37

Only 5 units left

Specifications

Model		LK-G5001V^1^2
Separate type		LK-G5001/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx. 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Non-voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Non-voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	NPN open-collector output
	General comparator output
Expansion connector	TIMING input	Non-voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Keyence GT2-A50 Keyence

$1,111.83

In stock, 14 units

Specifications

Model		GT2-A50
Detection system		Quartz glass scale, CMOS image sensor projection system, Absolute type (without tracking error)
Measuring range		50 mm 1.97"
Resolution		0.5 μm 0.02 Mil
Indicated accuracy		3.5 µm 0.14 Mil (p-p)^*1
Measuring force	Downward mounting	3.2 N^*2
	Side mounting	2.8 N^*2
	Upward mounting	2.4 N^*2
Sampling cycle		1 ms
Operation indicator light		2-color LED (red, green)
Environmental resistance	Enclosure rating	IP67^*3
	Pressure resistance	1 MPa
	Applied pressure range	0.25 to 0.5 MPa
	Ambient temperature	0 to +55 °C 32 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions^*4
Materials	Main body	Main body case: Zinc die-casting; Cylinder part: Aluminium alloy; Air joint resin part: Polyacetal; Air joint metal part: Brass nickel plating; Indicator: Polyarylate
	Dust boot	NBR
	Contact	TYPE304, 440C Stainless steel^*5
Sensor head cable		Optional (connect to the M8 connector)
Weight		Approx. 405 g (excluding cable)
^1 Value when the ambient temperature is 20 °C 68 °F. ^2 Value at center of measuring range. Please note that the measurement force changes depending on the installation state of the dust boots. ^3 Make sure the air tube is connected to the air exhaust joint and that no foreign materials enter inside from the joint. ^4 In the case where a mounting bracket D is used with GT2-A32 and GT2-A50, the double amplitude becomes 0.75 mm 0.03". ^*5 The contact is included with the sensor.

Sick RT-P3221 SICK

$164.22

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Pepperl+Fuchs KFD2-SOT2-EX2 Pepperl+Fuchs

$250.65

Only 9 units left

Pepperl+Fuchs KFD2 Signal Conditioner (P/N: KFD2-SOT2-EX2). K-System isolated barrier with galvanic isolation, ATEX/IECEx certification for 4-20mA, HART, thermocouple, RTD, and NAMUR process signals. DIN-rail mounted with spring terminals.