Sensors & Detection

$933.03

In stock, 11 units

Specifications

Model		LR-ZH490CB^*1
Type		U.C.D. Function Distance based laser sensor
Appearance		M18 Threaded mount
Output		NPN/PNP selectable
Cable connection		M12 connector, 4-pin
Detectable distance		25 to 490 mm 0.98" to 19.29" (465 to 0)^*2
Standard detectable deviation		25 to 170 mm 0.98" to 6.69": 9 mm 0.35" 170 to 290 mm 6.69" to 11.42": 25 mm 0.98" 290 to 390 mm 11.42" to 15.35": 40 mm 1.57" 390 to 490 mm 15.35" to 19.29": 50 mm 1.97"
Display resolution		1 to 5 (1 to 5 mm 0.04" to 0.20")
Spot size		Approx. ø3 mm ø0.12"
Response time		1.5 ms / 10 ms / 50 ms selectable
Light source	Type	Red laser (660 nm)
	Laser class	Class 2 laser product (IEC60825-1) Class II Laser product (FDA(CDRH) Part1040.10)
Function	Indicator	3-digit 7-segment display (white), output indicator (yellow), DATUM indicator (orange), 1 spot indicator (green)
	Timer	OFF/ON delay/OFF delay/One-shot
Specifications	Power voltage	10 to 30 VDC, including 10% ripple (P-P), Class 2 or LPS
	Power consumption	450 mW or less (18 mA or less at 24 V, 34 mA or less at 12 V)
	Control output	NPN open collector/PNP Open collector selectable, Applied voltage 30 VDC or less, Control current 100 mA or less, Residual voltage 1.2 V or less at 10 mA or less, 2 V or less at 10 to 100 mA
	Protection circuit	Protection against reverse power connection, output overcurrent, output surge, reverse output connection
	Output operation	Light-ON / Dark-ON selectable
	External input	Input time calibration: 35 ms or more ON, 35 ms or more OFF Laser emission stop: 2 ms or more ON, 20 ms or more OFF Short-circuit current NPN: 1 mA or less/PNP: 2 mA or less
Environmental resistance	Enclosure rating	IP68 (IEC60529), IP69K (DIN40050-9), NEMA 4X, 6P, 13 (NEMA250), ECOLAB^3, Diversey^3
	Insulation resistance	20 MΩ or more (500 VDC)
	Ambient light	Incandescent lamp: 10,000 lux or less Sunlight: 20,000 lux or less at 240 mm 9.45"^4 Incandescent lamp: 2,000 lux or less Sunlight: 4,000 lux or less at 490 mm 19.29"^4
	Ambient temperature	-10 to +50 °C 14 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-25 to +75 °C -13 to 167 °F (No freezing)
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: SUS316L, Display: PES, Lens cover: PMMA with scratch-resistant coating, Packing/Connector ring: FKM, Nut: SUS316L, Lock washer: SUS304
Accompanying items		Instruction Manual, FDA warning/certification/identification label, Laser warning/explanation labels
Weight		Approx. 75 g
^1 IO-Link specification v.1.1/COM2 (38.4 kbps) is supported. (LR-ZH490CB : Only when PNP output is selected.) You can download a setup file from the KEYENCE website. If using the product in an environment in which downloading files over the internet is not possible, contact your nearest KEYENCE office. ^2 Display readings can be used as a guide for the detecting distance. When the setting value is tuned, the readout shifts. When the value exceeds "-99", "-FF" is displayed. ^3 Have passed resistance tests with cleaning agents from multiple manufactures. ^4 When the response time is 10 ms

Keyence FS-V31P Keyence

$146.33

In stock, 12 units

Specifications

Model		FS-V31P
Type		1-output with cable
Output		PNP
Main unit/Expansion unit		Main unit
Control output		1 output
Monitor output (1 to 5 V)		N/A
External input
Connector		―
Light source LED		Red, 4-element LED (Wavelength: 640 nm)
Response time		33 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER TURBO) /4 ms (ULTRA TURBO) /16 ms (MEGA TURBO)
Output selection		LIGHT-ON/DARK-ON (switch-selectable)
Display indicator		Operation indicator: Red LED/Dual digital monitor: Dual 7-segment display, Preset Value (4-digit green LED indicator) and Current Value (4-digit red LED indicator) illuminated together. Current Value range: 0 to 64,512; Excess gain: 0P to 999P, Hold function: Possible to display both peak and bottom hold values, Selectable from 5 variations Bar LED monitor: Excess gain displayed (85% to 115% in 7 steps), Scaling display
Size		30.3 mm (H) x 9.8 mm (W) x 71.8 mm (D) 1.19" (H) x 0.39" (W) x 2.83" (D)
Detection mode		Light intensity (area detection possible, automatic sensitivity-tracking function provided)
Timer function		OFF-delay timer/ON-delay timer/One-shot timer/ON-delay timer + OFF-delay timer/ON-delay timer + One-shot timer, selectable Timer duration selectable: 0.1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.
Control output		PNP open-collector 24 V, 100 mA max.^*1 (main unit only)/20 mA max. (when the expansion unit(s) is connected), Residual voltage: 1 V max.
External inputy		Input time: 2 ms (ON)/20 ms (OFF) min.^*2
Unit expansion		Up to 16 expansion units can be connected (a total of 17 units). Note that the 2-output type should be counted as two units.
Number of interference prevention units	Normal operation	HIGHSPEED：0 FINE：4 TURBO/SUPER/ULTRA/MEGA：8台
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Power consumption	Normal: 750 mW max. (Using 24 V, 31 mA max., using 12 V, 40 mA max.)/ Power saving 580 mW max. (Using 24 V, 24 mA max., using 12 V, 28 mA max.)^*3
Environmental resistance	Ambient light	Incandescent lamp: 20,000 lux max., Sunlight: 30,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*4
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Accessories		N/A
Weight		Approx. 80 g
^1 Total current of two outputs should be less than 100 mA. ^2 Only available on certain models. ^3 When using the HIGH SPEED mode, the power consumption increases by 160 mW (7 mA). ^4 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less. 1 to 2 Units: -10 to +55 °C 14 to 131 °F, 3 to 10 Units: -10 to +50 °C 14 to 122 °F, 11 to 16 Units: -10 to +45 °C 14 to 113 °F

Keyence FD-Q32C Keyence

$629.16

In stock, 14 units

Specifications

Model		FD-Q32C
Supported pipe diameter		1" (25 A), ø28 to ø37 (mm) 1 1/4" (32 A), ø37 to ø44 (mm)
Supported pipe materials		Metal pipe/Resin pipe^*1
Supported fluids		Various liquid [i.e. water (including DI), oils, chemicals, etc.]^*1
Supported fluid temperature		0 to 85°C 32 to 185°F (No freezing on the pipe surface)^*2
Maximum rated flow		1" (25 A): 200 L/min, 52.8 G/min 1 1/4" (32 A): 300 L/min, 79.3 G/min
Zero cut flow rate		5 L/min (Default)^*3
Display method		Status indicator, output indicator, dual row display with 4-digit, 7 segment LED, stability level indicator
Display update cycle		Approx. 3 Hz
Display resolution		0.1/ 1 (Default :1) (L/min)
Response time		0.5 s / 1.0 s / 2.5 s / 5 s / 10 s / 30 s / 60 s
Protection circuit		Power supply reverse connection protection, power supply surge protection, each output short-circuit protection, each output surge protection
Repeatability		0.5 s : ±2.0%, 1 s:±1.5%, 2.5 s : ±1.0%, 5 s : ±0.5%, 10 s : ±0.35%, 30 s : ±0.2%, 60 s : ±0.15% (/F.S.^*4(Specific to selected response time))
Hysteresis		Variable
Integrated flow unit display		1/ 10/ 100/ 1000/ 10000 (Default : 1) (L)
Integrated flow data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length: 10 years or longer, Data read/write frequency: 1 million times or more)
Power I/O connector		M12 4-pin connector
Input/Output (Selectable)	Output (ch.1/ch.2)	Control output/ Pulse output/ Error output (Selectable, Default : ch.1 control output/ ch.2 not used), NPN/PNP setting switchable,open collector output 30 V or less, max. 100 mA/ch., residual voltage 2.5 V or less^*5
	Analog output (ch.2)	4 to 20 mA / 0 to 20 mA (Selectable, Default: not used), load resistance 500 Ω or less^*5
	External input (ch.2)	Integrated flow reset input/ Flow rate zero input/ Origin adjustment input (Selectable, Default: not used), short-circuit current 1.5 mA or less, input time 20 ms or more^*5
Power supply	Power voltage	20 to 30 VDC , ripple (P-P) 10% max, Class2/LPS
	Current consumption	130 mA or less (Load current excluded)^*6
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	100 m/s², 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Sensor main unit	PPS/PES/PBT/SUS303/SUS304/SUSXM7
	Sensor surface	Rubber
	Mounting bracket	SUS304/PA/POM/SUSXM7
Weight		Approx. 530 g (including mounting bracket)
^1 Liquid must allow for the passage of an ultrasonic pulse, as well as not contain large air pockets or excessive bubbles. Detection may be unstable on certain non-standard pipes (i.e. lined pipes) ^2 Contact KEYENCE when the temperature of the pipe is greater than 85°C 185°F ^3 The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate. ^4 This specification is valid when the flow velocity distribution is stable. This value does not take into account the effects of pulsation or fluctuations in flow velocity distribution due to facility factors. Convert the F.S. (full scale) listed in the table according to the rated flow range. ^5 IO-Link: Compatible with Specification v1.1 / COM2 (38.4 kbps) The setting file can be downloaded from the KEYENCE website. If using the unit in the environment where downloading the file is not possible via internet, contact your nearest KEYENCE office. IO-Link is either registered trademarks or trademarks of PROFIBUS Nutzerorganisation e.V. (PNO) ^6 When including the loads, please add 200 mA to this value.

Sick GTB6-N1211 SICK

$91.11

In stock, 12 units

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick YM2X18-100EG1MRJA8 PUR/4*2*0,14/GN/SH Sick

$189.02

Only 7 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Omron CQM1-OD214 Omron

$289.58

Only 8 units left

OUTPUT MODULE, 5-24VDC, 16POINTS

Omron C200H-OC226N Omron

$908.61

Only 1 unit left

OUTPUT/INPUT MODULE, SYSMAC C200, 16 POINT CONTACT , MDL, 16X RELAY OUTPUTS, 2 AMP, 24 VDC/250 VAC, 50/60 HZ

Omron S8VK-C48024 Omron

$158.97

Only 10 units left

Book type power supply, Lite, 480 W, 24VDC, 20A, DIN rail mounting

Omron CQM1-OC222 Omron

$204.71

Only 10 units left

Omron CQM1-OC222 RELAY OUTPUT MODULE - 16 RELAY OUTPUTS 24 VDC/250 VAC

Omron 3G3MX2-AB004-E Omron

$0.00

Sold Out

MX inverter drive, 0.4/0.55 kW (HD/ND), 3.0/3.5 A (HD/ND), 200 VAC, 1~ input, sensorless vector

Keyence LR-W70C Keyence

$474.65

Only 9 units left

Specifications

Model		LR-W70C
Type		Small/Dual Spot Type M12 connector 4-pin type
Detecting distance		30 to 70 mm 1.18" to 2.76"
Min. spot diameter		Approx. 1.6 x 2.9mm at 50 mm 0.06" × 0.11" at 1.97"
Light source		White LED
Mutual interference reduction function		Up to 2 units when alternate frequencies set
Timer		OFF/ON delay/OFF delay/One-shot
Response time		1-Spot Mode: 200 µs, 1 ms, 10 ms, 100 ms, 500 ms selectable 2-Spot Mode, Difference Monitoring: 500 µs, 2.5 ms, 20 ms, 200 ms, 999 ms selectable 2-Spot Mode, 2-Point Matching: 400 µs, 2 ms, 20 ms, 200 ms, 999 ms selectable^*1
I/O	Control output	NPN open collector/PNP open collector selectable 30 VDC or less, 50 mA or less, remaining voltage: 2 V or less N.O./N.C. selectable ^*2
	External input	Tuning /Transmission OFF selectable Short circuit current: 1 mA or less for NPN/2 mA or less for PNP For the applied voltage, see the wiring diagrams in the instruction manual. For the input times, see the time charts in the instruction manual. ^*2
Protection circuit		Protection against reverse power connection, power supply surge, output overcurrent, output surge, and reverse output connection
Power supply	Power voltage	10 to 30 VDC, including 10% ripple (P-P), Class 2 or LPS
	Current consumption	60 mA or less (without load) at 24 VDC; 110 mA or less (without load) at 12 VDC)^*3
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient light	Incandescent lamp: 10,000 lux or less, Sunlight: 20,000 lux or less
	Ambient temperature	-20 to +50 °C -4 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: Zinc die cast (Nickel chrome plating), Indicator cover: PPSU, Buttons: PES, Lens cover and display: PMMA (scratch-resistant coating), Connector ring: PMP, Connector socket: PEI
Weight		Approx. 75 g
^1 When alternate frequencies are set, the response time increases by approximately 20%. ^2 IO-Link: Specification v.1.1/COM2 (38.4 kbps) is supported. The setup file can be downloaded from KEYENCE website (http://www.keyence.com). If you are using the product in an environment in which you cannot download files over the Internet, contact your nearest KEYENCE office. ^*3 180 mA or less (at 10 V, with load)

Keyence FD-XA1 Keyence

$544.13

In stock, 11 units

Specifications

Model		FD-XA1
Type		DIN rail type, main unit
Display method		Output indicator, 4-digit 7 segment display, OLED, Stability level display
Display refresh frequency		Instantaneous flow: approx. 5 times/second, Discharge amount/Accumulated flow approx. 30 times/second
Response time		50 ms/100 ms/500 ms/1 s/2.5 s/5 s/10 s/30 s/60 s (selectable, default: 500 ms)
Integration data storage interval		Written to the memory every 10 seconds
Memory back up		EEPROM (data storage period: more than 10 years, number of data rewritable times: 1 million times or more) ^*1
Detection mode	ch.1	Instantaneous flow rate mode/Area mode/Pulse output (+) mode/Integrated flow mode/Shot mode (selectable)
	ch.2	Instantaneous flow rate mode/Area mode/Pulse output (-) mode/Shot mode/Error output mode/Bubble alert mode/Error + bubble alert mode (selectable)
Input/output	Output	NPN/PNP setting switch Open collector output: 30 V or lower, main unit: 50 mA or lower/ch.^*2/expansion unit: 20 mA or lower/ch., residual voltage: 2 V or lower
	Analog output	4-20 mA/0-20 mA (selectable) load resistance: 500 ohms or lower
	External input	Flow rate zero input/shot sampling input/integrated flow reset input/zero shift input (selectable) Short circuit current: NPN 1 mA or lower/PNP 2 mA or lower, input time: 20 ms or longer
Network support		IO-Link^*3
Unit expansion		Up to 7^*4 per main unit
Protection circuit		Power supply reverse connection protection, power surge protection, output short circuit protection, output surge protection
Power supply	Power voltage	20 to 30 VDC including 10 % ripple (P-P) , Class 2
	Power consumption	195 mA or lower (including the sensor head, excluding the load current)
Environmental resistance	Ambient temperature	-10 to +50 °C (No freezing) 14 to 122 °F
	Relative humidity	35 % to 85 %RH (No condensation)
	Vibration resistance	10 - 55 Hz, double amplitude 1.5 mm 0.06 ", 2 hours each for X,Y,Z direction
	Shock resistance	100 m/s² (approx. 10 G) 16 ms pulse, 1000 times each for X,Y,Z direction
Material		Main body case/front sheet: PC, Key top: POM, Cable: PVC
Weight		Approx. 210 g
^1 Internal data from full time recording can be read via USB (Ver.2.0) communication. ^2 20 mA or lower/ch when adding expansion units. ^3 IO-Link: Specification v1.1/COM2 (38.4 kbps) is supported. If the end of the cable needs to be an M12 connector when supporting IO-Link communication, connect an M12 conversion connector (OP-88296) to the cable. ^4 Refer to the Instruction Manual for the number of connected units to N-bus devices.

Schneider XS8C4A1PCG13 Schneider

$127.62

Only 7 units left

inductive sensor XS8 40x40x117 - PBT - Sn20 mm - 12..48VDC - terminals

Omron CQM1-DA022 Omron

$1,082.58

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Omron NX-OD6121-5 Omron

$476.81

Only 1 unit left

Controllers 32 NPN Outputs MIL Cntr

Keyence GT2-H12 Keyence

$522.89

In stock, 15 units

Specifications

Model		GT2-H12
Detection system		Quartz glass scale, CMOS image sensor projection system, Absolute type (without tracking error)
Measuring range		12 mm 0.47"
Resolution		0.5 μm 0.02 Mil
Indicated accuracy		2 µm 0.08 Mil (p-p)^*1
Measuring force	Downward mounting	1.0 N^*2
	Side mounting	0.9 N^*2
	Upward mounting	0.8 N^*2
Sampling cycle		1 ms
Mechanical response		10 Hz^*1
Operation indicator light		2-color LED (red, green)
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s² (IEC60068-2-27)
Materials	Main body	Main body cast: Zinc die-casting, Indicator: Polyarylate, Dust boot: NBR
	Dust boot	NBR
	Contact	TYPE304, 440C Stainless steel^*3
Sensor head cable		Optional (connect to the M8 connector)
Weight		Approx. 95 g (excluding cable)
^1 Value when the ambient temperature is 20 °C 68 °F. ^2 Value at center of measuring range. Please note that the measurement force changes depending on the installation state of the dust boots. ^*3 The contact is included with the sensor.

Omron NX-DA3603 Omron

$433.38

Only 7 units left

Controllers NX 4Pt D/A +-10 1/8k 250us/pt

Omron C200H-MC221 Omron

$17,593.48

Only 1 unit left

Motion control unit, 2 axis, analog output, circular interpolation

Keyence LV-N11CP Keyence

$269.57

In stock, 11 units

Specifications

Model		LV-N11CP
Type		1 output
Output		PNP
Cable/connector		M8 connector
Main/Expansion unit		Main unit
I/O	Control outputs	1 output
	External input	1 input
	Monitor output	None
Output selection		LIGHT-ON/DARK-ON (switch-selectable)
Timer function		Timer OFF/OFF-delay timer/ON-delay timer/One-shot timer, Timer duration selectable: 1 ms to 9,999 ms, Maximum error against the setting value: ±10% max.
Control outputs		PNP open collector 30 V, Residual voltage 1.2 V or less (Output current: 10 mA or less) / 2.2 V or less (Output current: 10 to 100 mA) (Stand-alone) 1 output max: 100 mA or less, 2 output total: 100 mA or less (Multiple connections) 1 output max: 20 mA or less
Response time		80 µs (HIGH SPEED)/250 µs (FINE)/500 µs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA) ^*1
Monitor output		-
External input		Input time 2 ms (ON)/20 ms (OFF) or more^*2
Number of interference prevention units		Connected to other than LV-S31: 0 for HIGH SPEED; 2 for FINE/TURBO/SUPER; 4 for ULTRA/MEGA, Connected to LV-S31: 2 for FINE; 4 for TURBO/SUPER/ULTRA/MEGA^*3
Case size		H 32.6 mm 1.28" × W 9.8 mm 0.39" × L 78.7 mm 3.1"
Unit expansion		Up to 17 units can be connected in total (two-output type is treated as two units)
Protection circuit		Reverse polarity protection, Over-current protection, Surge absorber
Rating	Power voltage	24 VDC (operating voltage 10 to 30 VDC (with ripple)), Ripple (P-P) 10 % or less, Class 2 or LPS^4^5
	Power consumption	Normal: 950 mW or less (at 30 V. 33 mA at 24 V, 60 mA or less at 12 V)^6 Eco on mode: 815 mW or less (at 30 V. 29 mA at 24 V, 52 mA or less at 12 V)^6 Eco Full mode: 650 mW or less (at 30 V. 24 mA at 24 V, 40 mA or less at 12 V) ^*7
Environmental resistance	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)^*8
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material	Cable	PVC
	Case	Main unit and cover material: Polycarbonate
Weight		Approx. 20 g
^1 80 µs cannot be selected when the LV-S31/S62/S63 is connected ^2 Input time is 25 ms (ON)/25 ms (OFF) when external calibration time is selected. ^3 These numbers double when "DOUBLE" is selected. ^4 Use with the over current protection device which is rated 30 V or more and not more than 1 A. ^5 To connect more than 9 units, the power voltage must be 20 V or more. ^6 Increases 30 mW (1 mA) for HIGH SPEED mode. ^7 It increases by 15% when connected to the LV-NH100/NH110/NH300. It does not include the power consumption of the load. Power consumption when expansion units are connected is the total power consumption of each amplifier unit. Example: When one main unit (LV-N11N) is connected to 2 expansion units (LV-N12N) and they are used with LV-NH100 heads in HIGH SPEED mode. (1.15 × 860 mW × 1) + (1.15 × 860 mW × 2) = 2967 mW max. ^8 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less for a unit. One or two more units connected: -20 to +55 °C -4 to 131 °F; 3 to 10 more units connected: -20 to +50 °C -4 to 122 °F; 11 to 16 more units connected: -20 to +45 °C -4 to 113 °F. When using 2-outputs, one unit is counted as two units.

Keyence IG-028 Keyence

$967.65

In stock, 17 units

Specifications

Model		IG-028
Operation principle		CCD method
Light source	Wavelength	660 nm (Visible light semiconductor laser)
	FDA	Class 1^*1
	IEC/JIS	Class 1
Mounting distance		0 to 1500 mm 59.06"
Measurement range		28 mm 1.10"
Sampling cycle		980 µs (When the number of times for averaging is set to [hsp]: 490 µs)
Minimum detectable object	High sensitivity mode	ø0.1 mm ø0.003" (Setting distance: 100 mm 3.94")^*2
	Standard mode	ø0.2 mm ø0.007" (Setting distance: 50 mm 1.97" or less), ø0.5 mm ø0.02" (Setting distance: 500 mm 19.68")^*2
Repeatability		5 µm 0.20 Mil (Setting distance: 100 mm 3.94") 10 µm 0.39 Mil (Setting distance: 500 mm 19.68") 80 µm 3.15 Mil (Setting distance: 1,000 mm 39.37") 140 µm 5.51 Mil (Setting distance: 1,500 mm 59.06")^*3
Linearity		±0.1 % of F.S. (±28 µm ±1.10 Mil)^*4
Temperature characteristics		±0.01 % of F.S./°C (±3 µm ±0.12 Mil/°C)^*5
Operation indicator	Transmitter	Optical axis alignment indicator: Green LED, Power indicator: Green LED
	Receiver	Optical axis alignment indicator: Green LED, Position monitor: Dual bar LED (Red, Green)
Environmental resistance	Enclosure rating	IP67
	Ambient light	Incandescent lamp: 5,000 lux, Sunlight: 5,000 lux^*6
	Ambient temperature	-10 to +45 °C 14 to 113 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material	Case	Zinc die-cast (Lower case), PBT (Upper case), Polyarylate (PAR) (Display part), SUS304 (Metallic part)
	Lens cover	Glass
	Cable	PVC
Accessories		Transmitter × 1, Receiver × 1, Sensor head cables (2 m 6.56') × 2
Weight		Approx. 500 g (including supplied items)
^1 The classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 When the measurement target object is measured at the center position of the setting distance. When the measurement mode is set to the glass edge mode, a glass edge of C0.1 mm 0.003" or more can be detected (Setting distance: 500 mm 19.69"). ^3 When the light is shielded by half at the center position of the setting distance. Vibration width when the average number of times is set to 16 and sampling is performed for 30 seconds. (When the analog output is used, the margin of error of analog output is added.) ^4 When the setting distance is 100 mm 3.94" and light is shielded at 50 mm 1.96"position from the receiver. Margin of error to the ideal line. ^5 When the setting distance is 100 mm 3.94" and light is shielded by half at 50 mm 1.96" position from the receiver. ^6 Excluding when the average number of times is set to [hsp].

Keyence GT2-H12K Keyence

$595.28

In stock, 18 units

Specifications

Model		GT2-H12K
Detection system		Quartz glass scale, CMOS image sensor projection system, Absolute type (without tracking error)
Measuring range		12 mm 0.47"
Resolution		0.1 μm 0.004 Mil
Indicated accuracy		1 µm 0.04 Mil (p-p)^*1
Measuring force	Downward mounting	1.0 N^*2
	Side mounting	0.9 N^*2
	Upward mounting	0.8 N^*2
Sampling cycle		1 ms
Mechanical response		10 Hz^*1
Operation indicator light		2-color LED (red, green)
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s² (IEC60068-2-27)
Materials	Main body	Main body cast: Zinc die-casting, Indicator: Polyarylate, Dust boot: NBR
	Dust boot	NBR
	Contact	TYPE304 Stainless steel, super-tough tungsten alloy^*3
Sensor head cable		Optional (connect to the M8 connector)
Weight		Approx. 95 g (excluding cable)
^1 Value when the ambient temperature is 20 °C 68 °F. ^2 Value at center of measuring range. Please note that the measurement force changes depending on the installation state of the dust boots. ^*3 The contact is included with the sensor.