Measurement Sensors

Filters

In stock (386)
Out of stock (658)

Showing 289 - 312 of 719 products

$0.00

Sold Out

Specifications

Model				WI-C10L
Type				Sensor head connecting cable, Standard
Cable end				L-shaped
Length				10 m 32.81'

Keyence WI-C10 Keyence

$0.00

Sold Out

Specifications

Model				WI-C10
Type				Sensor head connecting cable, Standard
Cable end				Straight
Length				10 m 32.81'

Keyence WI-010 Keyence

$36,967.75

Only 4 units left

Specifications

Model		WI-010^1^2^*3
Reference distance		18 mm 0.71"
Measurement range	Z	1.4 mm 0.06" (Standard Mode), 0.7 mm 0.03" (High Speed Mode)
	XY	10 × 10 mm 0.39" × 0.39"
Minimum detection area		40 × 40 µm 0.001575" × 0.001575"
Repeatability (height difference)		0.1 µm 0.000004"^*4
Linearity (height difference)		±2.8 µm 0.000110"(±0.2% of F.S., F.S. = 1.4 mm 0.06", +20 to +30°C +68 to +86°F)^*5
Light source for measurement	Type	Infrared SLD
	Center wavelength	830 nm
	Laser class (IEC60825-1)	Class 3R
	Output	3.6 mW
Guide light source	Type	Red semiconductor laser
	Wavelength	660 nm
	Laser class (IEC60825-1)	Class 1
	Output	0.15 mW
Sampling frequency	Internal Trigger	133 ms (High Speed Mode), 266 ms (Standard Mode)
	External Trigger	266 ms max. (High Speed Mode), 532 ms max. (Standard Mode)^*6
Environmental resistance	Ambient light	Incandescent lamp/fluorescent lamp: 5,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	20 to 85 % RH (No condensation)
Weight		Approx. 3,000 g
^1 The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice.The resolution of the height (distance from head reference plane to measurement workpiece) is 1 µm(2). ^2 This is ±3 σ value (Auto Maintenance Mode is OFF) when the average height of a single rectangular area(3) has been measured for 30 seconds using a KEYENCE standard target. ^3 The rectangular size is WI-001 : 0.3 mm × 0.9 mm 0.01" × 0.04", WI-004 : 1.1 mm × 3.7 mm 0.04" × 0.15", WI-010 : 3 mm × 9 mm 0.12" × 0.35". ^4 This is σ value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured for 30 seconds using a KEYENCE standard target. ^5 This is the value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured using a KEYENCE standard target. ^6 The workpiece stopping time at capturing is 120 ms (High Speed Mode) or 240 ms (Standard Mode).

Keyence WI-004 Keyence

$0.00

Sold Out

Specifications

Model		WI-004^1^2^*3
Reference distance		18 mm 0.71"
Measurement range	Z	1.4 mm 0.06" (Standard Mode), 0.7 mm 0.03" (High Speed Mode)
	XY	4 × 4 mm 0.16" × 0.16"
Minimum detection area		15 × 15 µm 0.000591" × 0.000591"
Repeatability (height difference)		0.1 µm 0.000004"^*4
Linearity (height difference)		±2.8 µm 0.000110"(±0.2% of F.S., F.S. = 1.4 mm 0.06", +20 to +30°C +68 to +86°F)^*5
Light source for measurement	Type	Infrared SLD
	Center wavelength	830 nm
	Laser class (IEC60825-1)	Class 3R
	Output	3.6 mW
Guide light source	Type	Red semiconductor laser
	Wavelength	660 nm
	Laser class (IEC60825-1)	Class 1
	Output	0.15 mW
Sampling frequency	Internal Trigger	133 ms (High Speed Mode), 266 ms (Standard Mode)
	External Trigger	266 ms max. (High Speed Mode), 532 ms max. (Standard Mode)^*6
Environmental resistance	Ambient light	Incandescent lamp/fluorescent lamp: 5,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	20 to 85 % RH (No condensation)
Weight		Approx. 3,000 g
^1 The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice.The resolution of the height (distance from head reference plane to measurement workpiece) is 1 µm(2). ^2 This is ±3 σ value (Auto Maintenance Mode is OFF) when the average height of a single rectangular area(3) has been measured for 30 seconds using a KEYENCE standard target. ^3 The rectangular size is WI-001 : 0.3 mm × 0.9 mm 0.01" × 0.04", WI-004 : 1.1 mm × 3.7 mm 0.04" × 0.15", WI-010 : 3 mm × 9 mm 0.12" × 0.35". ^4 This is σ value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured for 30 seconds using a KEYENCE standard target. ^5 This is the value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured using a KEYENCE standard target. ^6 The workpiece stopping time at capturing is 120 ms (High Speed Mode) or 240 ms (Standard Mode).

Keyence WI-001 Keyence

$0.00

Sold Out

Specifications

Model		WI-001^1^2^*3
Reference distance		18 mm 0.71"
Measurement range	Z	1.4 mm 0.06" (Standard Mode), 0.7 mm 0.03" (High Speed Mode)
	XY	1 × 1 mm 0.04" × 0.04"
Minimum detection area		4 × 4 µm 0.000157" × 0.000157"
Repeatability (height difference)		0.1 µm 0.000004"^*4
Linearity (height difference)		±2.8 µm 0.000110"(±0.2% of F.S., F.S. = 1.4 mm 0.06", +20 to +30°C +68 to +86°F)^*5
Light source for measurement	Type	Infrared SLD
	Center wavelength	830 nm
	Laser class (IEC60825-1)	Class 3R
	Output	3.6 mW
Guide light source	Type	Red semiconductor laser
	Wavelength	660 nm
	Laser class (IEC60825-1)	Class 1
	Output	0.15 mW
Sampling frequency	Internal Trigger	133 ms (High Speed Mode), 266 ms (Standard Mode)
	External Trigger	266 ms max. (High Speed Mode), 532 ms max. (Standard Mode)^*6
Environmental resistance	Ambient light	Incandescent lamp/fluorescent lamp: 5,000 lux max.
	Ambient temperature	0 to +35 °C 32 to 95 °F
	Relative humidity	20 to 85 % RH (No condensation)
Weight		Approx. 3,000 g
^1 The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice.The resolution of the height (distance from head reference plane to measurement workpiece) is 1 µm(2). ^2 This is ±3 σ value (Auto Maintenance Mode is OFF) when the average height of a single rectangular area(3) has been measured for 30 seconds using a KEYENCE standard target. ^3 The rectangular size is WI-001 : 0.3 mm × 0.9 mm 0.01" × 0.04", WI-004 : 1.1 mm × 3.7 mm 0.04" × 0.15", WI-010 : 3 mm × 9 mm 0.12" × 0.35". ^4 This is σ value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured for 30 seconds using a KEYENCE standard target. ^5 This is the value (Auto Maintenance Mode is OFF, Capture Timing is “Prioritize Accuracy”) when the average height difference of two rectangular areas(3) has been measured using a KEYENCE standard target. ^6 The workpiece stopping time at capturing is 120 ms (High Speed Mode) or 240 ms (Standard Mode).

Keyence CA-E300LJ Keyence

$0.00

Sold Out

Specifications

Model		CA-E300LJ
Controller		XG-X2902LJ
Head input		2 points ^*1
Supported heads		LJ-S015/LJ-S025/LJ-S040/LJ-S080/LJ-S160/LJ-S320/LJ-S640
Power supply		Supplied from controller
Environmental resistance	Ambient temperature	0 to +45°C 32 to 113°F (DIN rail mount) / 0 to +40°C 32 to 104°F (base surface mount)
	Relative humidity	85% RH or less (no condensation)
Weight		Approx. 560 g 19.77 oz
^*1 When two input units are connected, one head can be connected to each unit. In such configurations, the heads can be different models.

Keyence OP-88837 Keyence

$1,418.61

Only 1 unit left

Specifications

Model				OP-88837
Length				10 m 32.8'

Keyence WI-5000 Keyence

$36,967.75

Only 4 units left

Specifications

Model		WI-5000
No. of connectable sensor heads		1
No. of registration settings		Up to 1000 settings on SD Card 1 and SD Card 2 individually (depending on the capacity and configuration of the SD Card),external switching possible
No. of measurement tools		100 tools/setting (20 are intended for position adjustment)
Measurement mode	Height	Height Measurement, Height Difference Measurement, Arranged Multi-Point Height Measurement, Free Multi-Point Height Measurement, Profile Measurement, and Continuous Height Measurement
	Dimension measurement	Measure Distance, Measure Width, Line/Angle, Detect Circle, and Detect Point
	Auxiliary function	Calculation, Image Region Generator, Line Display, Circle Display, Point Display, and Scale Display
Interface	Control input	20 (Input terminal: 5, Parallel I/O: 15)
	Control output	28 (Output terminal block: 6, Parallel I/O: 22) Photo MOSFET^*1
	RS-232C	Value output and control I/O (cannot be used when PLC link using the RS-232C port is in use)
	PLC-Link	Value output and control I/O using the Ethernet port or RS-232C port (cannot be used when EtherNet/IP™ is in use. RS-232C No-protocol communication cannot be used when the RS-232C port is in use)
	Ethernet	Value output and control I/O In addition to the functions above, uploading/downloading inspection settings, various simulations, and transmission/reception/remote connection of image and other data are possible when KEYENCE's PC application software is connected. FTP client/server function supported, VNC server function (supporting monitor screen display only on clients other than a PC), and　BOOTP function supported 1000BASE-T/100BASE-TX/10BASE-T
	USB	In addition to value output and control I/O, uploading/downloading inspection settings, various simulations, and transmission/reception/remote connection of image and other data are possible when KEYENCE's PC application software is connected. Dedicated USB 2.0
	EtherNet/IP™	Value I/O and control I/O using the Ethernet port (cannot be used when PLC-Link is in use) Cyclic communication supported (up to 1436 bytes), message communication supported Max. number of connections: 32 Conforms to Conformance test Version CT12.
	Mouse	Menus can be operated with the optional dedicated mouse (OP-87506, included with the controller).
	USB HDD	Image and other data can be output when a HDD (2 TB max.) is connected to the dedicated USB port (conforms to USB3.0, bus power supported: rated output 900 mA)
	Monitor output	Analog RGB output XGA 1024 × 768 (24-bit color, 60 Hz)
Minimum display unit		0.1 µm, 0.001°, 0.0001 mm², 0.00001 mm³
Display language		English/Japanese/Chinese (simplified)/Chinese (traditional)/Korean selectable (Initial language should be determined during the initial startup.)
Rating	Maximum current consumption	2.7 A
	Power voltage	24 VDC ±10 %
Environmental resistance	Ambient temperature	0 to +45 °C 32 to 113 °F (DIN rail mounting), 0 to +40 °C 32 to 104 °F (bottom mounting)
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 2,000 g
^*1 Either positive common connecting which is compatible with NPN input devices, or negative common connecting which is compatible with PNP input devices is feasible.

Keyence OP-88836 Keyence

$358.50

Only 2 units left

Specifications

Model				OP-88836
Length				5 m 16.4'

Keyence OP-88835 Keyence

$37,597.50

Only 3 units left

Specifications

Model				OP-88835
Length				2 m 6.6'

Keyence GR-M256 Keyence

$0.00

Sold Out

Specifications

Model				GR-M256
Type				CF Memory
Applicable product				GR-7000 Series, GR-3500 Series, NR-600 Series
Memory capacity				256 MB

Keyence OP-88826 Keyence

$0.00

Sold Out

Specifications

Model				OP-88826
Length				L-shaped/0.2 m 0.7'

Keyence OP-88825 Keyence

$0.00

Sold Out

Specifications

Model				OP-88825
Length				L-shaped/0.2 m 0.7'

Keyence LJ-GC5 Keyence

$662.67

Only 3 units left

Specifications

Model				LJ-GC5
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				5 m 16.40'
Weight				Approx. 400 g

Keyence LJ-GC30 Keyence

$0.00

Sold Out

Specifications

Model				LJ-GC30
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				30 m 98.42'
Weight				Approx. 2,000 g

Keyence LJ-GC20 Keyence

$426.83

Only 1 unit left

Specifications

Model				LJ-GC20
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				20 m 65.62'
Weight				Approx. 1,400 g

Keyence LJ-GC2 Keyence

$798.20

Only 5 units left

Specifications

Model				LJ-GC2
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				2 m 6.56'
Weight				Approx. 200 g

Keyence CA-U5 Keyence

$644.99

Only 6 units left

Specifications

Model		CA-U5
Input conditions	Rated input voltage	85 to 264 VAC 47 to 63 Hz, 110 to 370 VDC ^*1
Inputconditions	Efficiency	82% (100 VAC) /85% (200 VAC) typ. (at 100% load)
Input conditions	Rated input current	3.9 A max. (100 VAC)/ 1.8 A max. (200 VAC)
Output conditions	Rated output voltage	24 VDC
	Rated output current	12.5 A
Protection	Overvoltage protection	15.6 A or more ^*2
		Activates at 26.4 V or more. Voltage interruption method, recovers when input is applied again. ^*3
Applicable standards	Safety standards	UL: UL508, UL60950-1 C-UL: CSA C22.2 No.14, CSA C22.2 No.60950-1 EN: EN62368-1, EN50178 IEC: IEC62368-1
	EMC standard	FCC Part15B ClassA, EN55011 ClassA, EN61000-6-2
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)
	Relative humidity	85%RH or less (No condensation)
	Storage temperature	-20 to +70 °C -4 to +158 °F (No freezing)
Weight		Approx. 1540 g 3.40 lb
^1 When applying for safety standards, the rated input voltage was 100 to 240 VAC and the rated frequency was 50/60 Hz. ^2 Constant current drop method, automatic recovery. ^*3 To recover, turn off the input power supply, leave it off for 1 minute or more, and then turn it on again.

Keyence LJ-GC10 Keyence

$525.00

Only 2 units left

Specifications

Model				LJ-GC10
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				10 m 32.81'
Weight				Approx. 750 g

Keyence LJ-H1W Keyence

$0.00

Sold Out

Specifications

Model				LJ-H1W
Type				Setup Support Software
Operating System				Windows 11 Pro Windows 10 ^1 Windows 7 (SP1 or later)^2 Windows Vista (SP2 or later)^3 Windows XP (SP3 or later)^4
CPU				Pentium III 400 MHz or higher
Memory capacity				128 MB or more
Available hard disk space				30 MB or more
Display				XGA (1024 x 768 pixels) or greater, 256 colors or greater
PC interface				Includes one of the following^5: USB 2.0/1.1^6, Ethernet^*7, RS-232C (Serial port)
^1 Home, Pro, and Enterprise editions each are supported. ^2 Home Premium, Professional, and Ultimate editions each are supported. ^3 Ultimate, Business, Home Premium, and Home Basic editions each are supported. ^4 Professional and Home Edition editions each are supported. ^5 Select one for communication. Multiple interfaces cannot be used for communication at the same time. ^6 Operations are not guaranteed when connected through a USB hub. ^*7 Operations are not guaranteed when connected through a router or a LAN connection.

Keyence LJ-G200 Keyence

$2,945.29

Only 9 units left

Specifications

Model			LJ-G200
Mounting			Diffuse reflective
Reference distance			200 mm 7.87"
Measuring range	Z-axis (Height)		±48 mm ±1.89"
	X-axis (Width)	Near	51 mm 2.01"
		Reference distance	62 mm 2.44"
		Far	73 mm 2.87"
Light source	Type		Red semiconductor laser
	Wavelength		655nm (Visible light), Class 2 laser product (JIS C6802)
	Output		0.95 mW
	Laser Class		Class II Laser Product (FDA (CDRH) 21CFR PART1040.10), Class 2 Laser Product (IEC 60825-1)
Spot shape (at reference distance)			Approx 180 µm x 70 mm 0.007087" x 2.76"
Repeatability	Z-axis (Height)		2 µm 0.000079"^*1
	X-axis (Width)		20 µm 0.000788"^*2
Linearity Z-axis (Height)			±0.1% of F.S.^*3
Sampling cycle (trigger interval)			3.8 ms^*4
Temperature characteristics			0.02% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529)
	Ambient light		Incandescent lamp or fluorescent lamp: 5,000 lux max.^*5
	Ambient temperature		0 to +50 °C 32 to 122 °F
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material			Aluminum
Weight			Approx. 480 g
^1 The value obtained after 64 times averaging at the reference distance.The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^2 The value obtained after 64 times averaging at the reference distance.The target is ø10 mm ø0.39" pin gauge. The value is the edge in the Position mode after 16 times of the Smoothing. ^3 The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^4 With initial setting, minimum measuring range, and single smoothing processing ^*5 The illumination on the receiver of the sensor head when targeting an illuminated white paper.

Keyence LJ-S640 Keyence

$0.00

Sold Out

Specifications

Model			LJ-S640
Reference distance			1116 mm 43.94"^*1
Measurement range	Z-axis (height)		+180/−250 mm +7.09"/−9.84" (F.S.=430 mm 16.93")
	X-axis (width)	NEAR side	579 mm 22.80"
		Reference distance	640 mm 25.20"
		FAR side
	Y-axis	Reference distance
XY data interval			200 μm 0.0079"
Number of XY data points			3200×3200
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		10 μm 0.0004"^*4
	XY (distance)		25 μm 0.0010"^*5
Linearity	Standard area		±0.058% of F.S.^*6
	High-accuracy area		±0.023% of F.S.^*6
Imaging time			Min. 0.3 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 5.5 A (at 19.2 V), 4.4 A (at 24 V)^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 4300 g 9.48 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-G080 Keyence

$967.65

In stock, 15 units

Specifications

Model			LJ-G080
Mounting			Diffuse reflective
Reference distance			80 mm 3.15"
Measuring range	Z-axis (Height)		±23 mm ±0.91"
	X-axis (Width)	Near	25 mm 0.98"
		Reference distance	32 mm 1.26"
		Far	39 mm 1.54"
Light source	Type		Red semiconductor laser
	Wavelength		655nm (Visible light), Class 2 laser product (JIS C6802)
	Output		0.95 mW
	Laser Class		Class II Laser Product (FDA (CDRH) 21CFR PART1040.10), Class 2 Laser Product (IEC 60825-1)
Spot shape (at reference distance)			Approx 80 µm x 46 mm 0.003150" x 1.81"
Repeatability	Z-axis (Height)		1 µm 0.000040"^*1
	X-axis (Width)		10 µm 0.000394"^*2
Linearity Z-axis (Height)			±0.1% of F.S.^*3
Sampling cycle (trigger interval)			3.8 ms^*4
Temperature characteristics			0.02% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529)
	Ambient light		Incandescent lamp or fluorescent lamp: 5,000 lux max.^*5
	Ambient temperature		0 to +50 °C 32 to 122 °F
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material			Aluminum
Weight			Approx. 350 g
^1 The value obtained after 64 times averaging at the reference distance.The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^2 The value obtained after 64 times averaging at the reference distance.The target is ø10 mm ø0.39" pin gauge. The value is the edge in the Position mode after 16 times of the Smoothing. ^3 The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^4 With initial setting, minimum measuring range, and single smoothing processing ^*5 The illumination on the receiver of the sensor head when targeting an illuminated white paper.

Keyence LJ-S320 Keyence

$0.00

Sold Out

Specifications

Model			LJ-S320
Reference distance			470.5 mm 18.52"^*1
Measurement range	Z-axis (height)		+100/−120 mm +3.94"/−4.72" (F.S.=220 mm 8.66")
	X-axis (width)	NEAR side	243 mm 9.57"
		Reference distance	295 mm 11.61"
		FAR side	320 mm 12.60"
	Y-axis	Reference distance
XY data interval			100 μm 0.0039"
Number of XY data points			3200×3200
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		5 μm 0.000197"^*4
	XY (distance)		10 μm 0.0004"^*5
Linearity	Standard area		±0.027% of F.S.^*6
	High-accuracy area		—
Imaging time			Min. 0.3 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 5.5 A (at 19.2 V), 4.4 A (at 24 V)^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 3700 g 8.16 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Previous Page 13 / 30Next

Filters

In stock (386)
Out of stock (658)