Keyence

NR-XTH08T Keyence

Specifications

Model				NR-XTH08T
Input method				Insulated single-end input, channels insulated from each other, input channels insulated from the case and other units (system)
Number of input channels				8^*1
Input connector type				Miniature thermocouple connector (Universal type)
Measurement cycle				Maximum sampling cycle: 10 ms (100 Hz) to 1 h
A/D converting system				Delta-sigma method
A/D resolution				24 bits
A/D integration time (noise filter)				AUTO (Automatic configuration according to sampling cycle), 2.5 ms (400 Hz), 16.7 ms (60 Hz), 20 ms (50 Hz), 100 ms (10 Hz)
Input type				Thermocouple: K, J, E, T, R, S, B, N, C
Low pass filter				PASS / 200 Hz / 20 Hz
Averaging				Switchable between ON/OFF, Averaging rate: 2 to 128 (moving average)
Reference contact compensation				Switchable between internal and external
Reference contact compensation accuracy				±0.5°C ±0.9°F (23°C ±3°C 73.4°F ±5.4°F at input terminal temperature equilibrium)
Maximum input rating				±30 V^*2
Maximum allowable input ground voltage				Dry locations: 30 VAC and 42.4 Vpeak, or 60 VDC Wet locations: 16 VAC and 22.6 Vpeak, or 35 VDC
Withstand voltage				Between measurement input terminal and case/other units (system): 1000 VAC (50 Hz / 60 Hz) for 1 minute Between measurement input terminals: 1000 VAC (50 Hz / 60 Hz) for 1 minute
Input impedance				10 MΩ or more
Input signal source resistance				2 kΩ or less
Thermocouple burnout detection				Switchable between ON/OFF, When ON: Approx. 10 μA current detection^*3
Measurable range				K: −100 to +1372°C -148°F to +2501.6°F, −200 to −100°C -328°F to -148°F J: −100 to +1200°C -148°F to +2192°F, −200 to −100°C -328°F to -148°F E: −100 to +1000°C -148°F to +1832°F, −200 to −100°C -328°F to -148°F T: −100 to +400°C -148°F to +752°F, −200 to −100°C -328°F to -148°F N: −100 to +1300°C -148°F to +2372°F, −200 to −100°C -328°F to -148°F C: 1500 to 2315°C 2732°F to 4199°F, 0 to 1500°C 32°F to 2732°F R: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F S: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F B: 400 to 600°C 752°F to 1112°F, 600 to 1820°C 1112°F to 3308°F
Measurement accuracy				K: ±0.04% of rdg ±0.4°C ±0.7°F, ±0.43% of rdg ±0.1°C ±0.2°F J: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.30% of rdg ±0.1°C ±0.2°F E: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.27% of rdg ±0.1°C ±0.2°F T: ±0.4°C ±0.7°F, ±0.34% of rdg ±0.1°C ±0.2°F N: ±0.02% of rdg ±0.6°C ±2.1°F, ±0.63% of rdg ±0.1°C ±0.2°F C: ±0.10% of rdg ±0.2°C ±0.4°F, ±0.04% of rdg ±0.8°C ±1.4°F R: ±0.01% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F S: ±0.02% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F B: ±2.2°C ±4.0°F, ±1.6°C ±2.9°F ^*4
Display resolution				K: 0.05°C 0.09°F J: 0.05°C 0.09°F E: 0.05°C 0.09°F T: 0.01°C 0.02°F N: 0.05°C 0.09°F C: 0.05°C 0.09°F R: 0.05°C 0.09°F S: 0.05°C 0.09°F B: 0.05°C 0.09°F
Buffer memory				16M data^*5
Warm up time				30 minutes or more
Common mode noise reduction ratio				135 dB or more (up to 60 Hz DC) (typ.) ^*4
Remote connection				Dedicated environment-resistant remote unit input port × 1 (Remote IN), output port × 1 (Remote OUT) Connection to NR-X100W master data collection unit or other NR-XR01 remote units using environment-resistant unit cable Connectable to multiple environment-resistant measurement units^*6
Synchronization accuracy between remote connection units				±1 μs^*7
Power supply				Supplied from NR-X100W master unit
Power consumption				5.0 W max.
Surrounding air temperature				−40 to +85°C -40°F to +185°F^*8
Operating ambient humidity				Max. 100% RH^*9
Vibration resistance				100 m/s² 328.1 ft/s²; 5 to 2000 Hz; 2 hours in each of the X, Y, and Z directions (IEC 60068-2-6)^*10 Equivalent to JIS D1601 Stage 45 (Class 1, Class 2, and Class 3; equivalent to Class B) automotive vibration standard
Shock resistance				1000 m/s² 3280.8 ft/s²; 3 times in each of the X, Y, and Z directions (18 times in total) (IEC 60068-2-27)
Enclosure rating				IP65/IP67 (IEC 60529) Enclosure Type 4X (UL 50E, CSA C22.2 No. 94.2, NEMA 250) Indoor/outdoor use
Material				Main unit case: Aluminum die-casting (coated) / PBT+PC / PC, Display: Reinforced glass, Connectors: Brass (chromate processing), Connector protection cap: PBT+PC
Weight				Approx. 660 g 23.30 oz
^1 Max. expansion: 64 ch (with 8 units connected, using NR-X100W) ^2 Protection rating against temporary overvoltage. Do not apply voltage directly from an external source. ^3 The time until detection is confirmed varies depending on the acquisition setting and the input signal source resistance. Detection may be disabled depending on the low-pass filter and sampling cycle settings. For details, see P. 5–29. ^4 Does not include reference junction compensation accuracy. Specified with an A/D integration time of 20 ms (50 Hz) / 16.7 ms (60 Hz), the low-pass filter set to PASS, averaging set to 2 times, and after the warm-up time has passed and the temperature has stabilized (23°C ±3°C 73.4°F ±5.4°F). ^5 The buffer memory that can be used by the entire system is limited by the NR-X100W buffer memory. ^6 Environment-resistant unit cables can be extended by connecting an environment-resistant unit extension cable. The total length of cables used in the system should be no more than 100 m 32.8'. The distance between the NR-X100W (or NR-XR01) and environment-resistant measurement units or between environment-resistant remote measurement units should be no more than 60 m 196.9'. ^7 The sampling cycle and timing vary depending on the various measurement units used in the system. ^8 Install the product on the specified mounting sheet metal (OP-88613) for use with ambient temperatures of 80°C 176°F or higher. ^9 Use the product under the condition that the absolute humidity is 85°C 185°F with 90% RH or less. Avoid sudden temperature and humidity changes to prevent significant condensation and freezing. ^10 Testing with a 50 mm 1.97" p-p displacement limit used for 5 to 10 Hz.

$3,549.99

1-year warranty

FREE WORDWIDE SHIPPING

Est. delivery between and

Condition:

Sealed Surplus

SKU: NR-XTH08T-Sealed

Sold out

$0.00

Never Used Surplus

SKU: NR-XTH08T

1 verified stock

$3,549.99

Used

SKU: NR-XTH08T-Used

Sold out

$0.00

Variant

Quantity:

Need More?

Specifications

Model				NR-XTH08T
Input method				Insulated single-end input, channels insulated from each other, input channels insulated from the case and other units (system)
Number of input channels				8^*1
Input connector type				Miniature thermocouple connector (Universal type)
Measurement cycle				Maximum sampling cycle: 10 ms (100 Hz) to 1 h
A/D converting system				Delta-sigma method
A/D resolution				24 bits
A/D integration time (noise filter)				AUTO (Automatic configuration according to sampling cycle), 2.5 ms (400 Hz), 16.7 ms (60 Hz), 20 ms (50 Hz), 100 ms (10 Hz)
Input type				Thermocouple: K, J, E, T, R, S, B, N, C
Low pass filter				PASS / 200 Hz / 20 Hz
Averaging				Switchable between ON/OFF, Averaging rate: 2 to 128 (moving average)
Reference contact compensation				Switchable between internal and external
Reference contact compensation accuracy				±0.5°C ±0.9°F (23°C ±3°C 73.4°F ±5.4°F at input terminal temperature equilibrium)
Maximum input rating				±30 V^*2
Maximum allowable input ground voltage				Dry locations: 30 VAC and 42.4 Vpeak, or 60 VDC Wet locations: 16 VAC and 22.6 Vpeak, or 35 VDC
Withstand voltage				Between measurement input terminal and case/other units (system): 1000 VAC (50 Hz / 60 Hz) for 1 minute Between measurement input terminals: 1000 VAC (50 Hz / 60 Hz) for 1 minute
Input impedance				10 MΩ or more
Input signal source resistance				2 kΩ or less
Thermocouple burnout detection				Switchable between ON/OFF, When ON: Approx. 10 μA current detection^*3
Measurable range				K: −100 to +1372°C -148°F to +2501.6°F, −200 to −100°C -328°F to -148°F J: −100 to +1200°C -148°F to +2192°F, −200 to −100°C -328°F to -148°F E: −100 to +1000°C -148°F to +1832°F, −200 to −100°C -328°F to -148°F T: −100 to +400°C -148°F to +752°F, −200 to −100°C -328°F to -148°F N: −100 to +1300°C -148°F to +2372°F, −200 to −100°C -328°F to -148°F C: 1500 to 2315°C 2732°F to 4199°F, 0 to 1500°C 32°F to 2732°F R: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F S: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F B: 400 to 600°C 752°F to 1112°F, 600 to 1820°C 1112°F to 3308°F
Measurement accuracy				K: ±0.04% of rdg ±0.4°C ±0.7°F, ±0.43% of rdg ±0.1°C ±0.2°F J: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.30% of rdg ±0.1°C ±0.2°F E: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.27% of rdg ±0.1°C ±0.2°F T: ±0.4°C ±0.7°F, ±0.34% of rdg ±0.1°C ±0.2°F N: ±0.02% of rdg ±0.6°C ±2.1°F, ±0.63% of rdg ±0.1°C ±0.2°F C: ±0.10% of rdg ±0.2°C ±0.4°F, ±0.04% of rdg ±0.8°C ±1.4°F R: ±0.01% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F S: ±0.02% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F B: ±2.2°C ±4.0°F, ±1.6°C ±2.9°F ^*4
Display resolution				K: 0.05°C 0.09°F J: 0.05°C 0.09°F E: 0.05°C 0.09°F T: 0.01°C 0.02°F N: 0.05°C 0.09°F C: 0.05°C 0.09°F R: 0.05°C 0.09°F S: 0.05°C 0.09°F B: 0.05°C 0.09°F
Buffer memory				16M data^*5
Warm up time				30 minutes or more
Common mode noise reduction ratio				135 dB or more (up to 60 Hz DC) (typ.) ^*4
Remote connection				Dedicated environment-resistant remote unit input port × 1 (Remote IN), output port × 1 (Remote OUT) Connection to NR-X100W master data collection unit or other NR-XR01 remote units using environment-resistant unit cable Connectable to multiple environment-resistant measurement units^*6
Synchronization accuracy between remote connection units				±1 μs^*7
Power supply				Supplied from NR-X100W master unit
Power consumption				5.0 W max.
Surrounding air temperature				−40 to +85°C -40°F to +185°F^*8
Operating ambient humidity				Max. 100% RH^*9
Vibration resistance				100 m/s² 328.1 ft/s²; 5 to 2000 Hz; 2 hours in each of the X, Y, and Z directions (IEC 60068-2-6)^*10 Equivalent to JIS D1601 Stage 45 (Class 1, Class 2, and Class 3; equivalent to Class B) automotive vibration standard
Shock resistance				1000 m/s² 3280.8 ft/s²; 3 times in each of the X, Y, and Z directions (18 times in total) (IEC 60068-2-27)
Enclosure rating				IP65/IP67 (IEC 60529) Enclosure Type 4X (UL 50E, CSA C22.2 No. 94.2, NEMA 250) Indoor/outdoor use
Material				Main unit case: Aluminum die-casting (coated) / PBT+PC / PC, Display: Reinforced glass, Connectors: Brass (chromate processing), Connector protection cap: PBT+PC
Weight				Approx. 660 g 23.30 oz
^1 Max. expansion: 64 ch (with 8 units connected, using NR-X100W) ^2 Protection rating against temporary overvoltage. Do not apply voltage directly from an external source. ^3 The time until detection is confirmed varies depending on the acquisition setting and the input signal source resistance. Detection may be disabled depending on the low-pass filter and sampling cycle settings. For details, see P. 5–29. ^4 Does not include reference junction compensation accuracy. Specified with an A/D integration time of 20 ms (50 Hz) / 16.7 ms (60 Hz), the low-pass filter set to PASS, averaging set to 2 times, and after the warm-up time has passed and the temperature has stabilized (23°C ±3°C 73.4°F ±5.4°F). ^5 The buffer memory that can be used by the entire system is limited by the NR-X100W buffer memory. ^6 Environment-resistant unit cables can be extended by connecting an environment-resistant unit extension cable. The total length of cables used in the system should be no more than 100 m 32.8'. The distance between the NR-X100W (or NR-XR01) and environment-resistant measurement units or between environment-resistant remote measurement units should be no more than 60 m 196.9'. ^7 The sampling cycle and timing vary depending on the various measurement units used in the system. ^8 Install the product on the specified mounting sheet metal (OP-88613) for use with ambient temperatures of 80°C 176°F or higher. ^9 Use the product under the condition that the absolute humidity is 85°C 185°F with 90% RH or less. Avoid sudden temperature and humidity changes to prevent significant condensation and freezing. ^10 Testing with a 50 mm 1.97" p-p displacement limit used for 5 to 10 Hz.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Specifications

Model				NR-XTH08T
Input method				Insulated single-end input, channels insulated from each other, input channels insulated from the case and other units (system)
Number of input channels				8^*1
Input connector type				Miniature thermocouple connector (Universal type)
Measurement cycle				Maximum sampling cycle: 10 ms (100 Hz) to 1 h
A/D converting system				Delta-sigma method
A/D resolution				24 bits
A/D integration time (noise filter)				AUTO (Automatic configuration according to sampling cycle), 2.5 ms (400 Hz), 16.7 ms (60 Hz), 20 ms (50 Hz), 100 ms (10 Hz)
Input type				Thermocouple: K, J, E, T, R, S, B, N, C
Low pass filter				PASS / 200 Hz / 20 Hz
Averaging				Switchable between ON/OFF, Averaging rate: 2 to 128 (moving average)
Reference contact compensation				Switchable between internal and external
Reference contact compensation accuracy				±0.5°C ±0.9°F (23°C ±3°C 73.4°F ±5.4°F at input terminal temperature equilibrium)
Maximum input rating				±30 V^*2
Maximum allowable input ground voltage				Dry locations: 30 VAC and 42.4 Vpeak, or 60 VDC Wet locations: 16 VAC and 22.6 Vpeak, or 35 VDC
Withstand voltage				Between measurement input terminal and case/other units (system): 1000 VAC (50 Hz / 60 Hz) for 1 minute Between measurement input terminals: 1000 VAC (50 Hz / 60 Hz) for 1 minute
Input impedance				10 MΩ or more
Input signal source resistance				2 kΩ or less
Thermocouple burnout detection				Switchable between ON/OFF, When ON: Approx. 10 μA current detection^*3
Measurable range				K: −100 to +1372°C -148°F to +2501.6°F, −200 to −100°C -328°F to -148°F J: −100 to +1200°C -148°F to +2192°F, −200 to −100°C -328°F to -148°F E: −100 to +1000°C -148°F to +1832°F, −200 to −100°C -328°F to -148°F T: −100 to +400°C -148°F to +752°F, −200 to −100°C -328°F to -148°F N: −100 to +1300°C -148°F to +2372°F, −200 to −100°C -328°F to -148°F C: 1500 to 2315°C 2732°F to 4199°F, 0 to 1500°C 32°F to 2732°F R: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F S: 300 to 1768°C 572°F to 3214.4°F, 0 to 300°C 32°F to 572°F B: 400 to 600°C 752°F to 1112°F, 600 to 1820°C 1112°F to 3308°F
Measurement accuracy				K: ±0.04% of rdg ±0.4°C ±0.7°F, ±0.43% of rdg ±0.1°C ±0.2°F J: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.30% of rdg ±0.1°C ±0.2°F E: ±0.03% of rdg ±0.3°C ±0.5°F, ±0.27% of rdg ±0.1°C ±0.2°F T: ±0.4°C ±0.7°F, ±0.34% of rdg ±0.1°C ±0.2°F N: ±0.02% of rdg ±0.6°C ±2.1°F, ±0.63% of rdg ±0.1°C ±0.2°F C: ±0.10% of rdg ±0.2°C ±0.4°F, ±0.04% of rdg ±0.8°C ±1.4°F R: ±0.01% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F S: ±0.02% of rdg ±1.2°C ±2.2°F, ±2.0°C ±3.6°F B: ±2.2°C ±4.0°F, ±1.6°C ±2.9°F ^*4
Display resolution				K: 0.05°C 0.09°F J: 0.05°C 0.09°F E: 0.05°C 0.09°F T: 0.01°C 0.02°F N: 0.05°C 0.09°F C: 0.05°C 0.09°F R: 0.05°C 0.09°F S: 0.05°C 0.09°F B: 0.05°C 0.09°F
Buffer memory				16M data^*5
Warm up time				30 minutes or more
Common mode noise reduction ratio				135 dB or more (up to 60 Hz DC) (typ.) ^*4
Remote connection				Dedicated environment-resistant remote unit input port × 1 (Remote IN), output port × 1 (Remote OUT) Connection to NR-X100W master data collection unit or other NR-XR01 remote units using environment-resistant unit cable Connectable to multiple environment-resistant measurement units^*6
Synchronization accuracy between remote connection units				±1 μs^*7
Power supply				Supplied from NR-X100W master unit
Power consumption				5.0 W max.
Surrounding air temperature				−40 to +85°C -40°F to +185°F^*8
Operating ambient humidity				Max. 100% RH^*9
Vibration resistance				100 m/s² 328.1 ft/s²; 5 to 2000 Hz; 2 hours in each of the X, Y, and Z directions (IEC 60068-2-6)^*10 Equivalent to JIS D1601 Stage 45 (Class 1, Class 2, and Class 3; equivalent to Class B) automotive vibration standard
Shock resistance				1000 m/s² 3280.8 ft/s²; 3 times in each of the X, Y, and Z directions (18 times in total) (IEC 60068-2-27)
Enclosure rating				IP65/IP67 (IEC 60529) Enclosure Type 4X (UL 50E, CSA C22.2 No. 94.2, NEMA 250) Indoor/outdoor use
Material				Main unit case: Aluminum die-casting (coated) / PBT+PC / PC, Display: Reinforced glass, Connectors: Brass (chromate processing), Connector protection cap: PBT+PC
Weight				Approx. 660 g 23.30 oz
^1 Max. expansion: 64 ch (with 8 units connected, using NR-X100W) ^2 Protection rating against temporary overvoltage. Do not apply voltage directly from an external source. ^3 The time until detection is confirmed varies depending on the acquisition setting and the input signal source resistance. Detection may be disabled depending on the low-pass filter and sampling cycle settings. For details, see P. 5–29. ^4 Does not include reference junction compensation accuracy. Specified with an A/D integration time of 20 ms (50 Hz) / 16.7 ms (60 Hz), the low-pass filter set to PASS, averaging set to 2 times, and after the warm-up time has passed and the temperature has stabilized (23°C ±3°C 73.4°F ±5.4°F). ^5 The buffer memory that can be used by the entire system is limited by the NR-X100W buffer memory. ^6 Environment-resistant unit cables can be extended by connecting an environment-resistant unit extension cable. The total length of cables used in the system should be no more than 100 m 32.8'. The distance between the NR-X100W (or NR-XR01) and environment-resistant measurement units or between environment-resistant remote measurement units should be no more than 60 m 196.9'. ^7 The sampling cycle and timing vary depending on the various measurement units used in the system. ^8 Install the product on the specified mounting sheet metal (OP-88613) for use with ambient temperatures of 80°C 176°F or higher. ^9 Use the product under the condition that the absolute humidity is 85°C 185°F with 90% RH or less. Avoid sudden temperature and humidity changes to prevent significant condensation and freezing. ^10 Testing with a 50 mm 1.97" p-p displacement limit used for 5 to 10 Hz.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

NR-XTH08T Keyence

Specifications

Specifications

Specifications