Machine Vision Systems

$453.27

Only 4 units left

Specifications

Model		PR-M51P3
Type		Thrubeam
Output		PNP
Shape		Mini-slim
Cable connection		3 m cable
Detection distance		1.2 m
Number of control outputs		2 outputs
Output operation	Output 1	Dark-ON
	Output 2	Light-ON
Response time	Output 1	0.5 ms
	Output 2	ON→OFF: 2.7 ms, OFF→ON: 0.5 ms
Sensitivity adjustment		None
Spot diameter		-
Light source		4 element, point light source, red LED (650 nm)
Mutual interference prevention function		-
Indicator lamp		Output indicator (orange), stable operation indicator (green), thrubeam type transmitter: power supply indicator (green)
Control output		30 VDC or lower, 50 mA or lower Leakage current: When 3 kΩ load resistance, 0.3 mA or lower. When 1 kΩ load resistance, 0.5 mA or lower. When 0.2 kΩ load resistance, 1.5 mA or lower Residual voltage: When 10 mA or lower, 1.0 V or lower. When 10 to 30 mA, 1.5 V or lower. When 30 to 50 mA, 2.0 V or lower.
Protection circuit		Power supply reverse connection protection, output overcurrent protection, output surge protection, power supply surge protection
Rating	Power voltage	10 to 30 VDC, including Ripple (P-P) 10 %
	Current consumption	Transmitter: 11 mA, Receiver: 16 mA
Environmental resistance	Enclosure rating	IP67 (IEC60529), IP69K (DIN40050-9), 4X, 6P, 13 (NEMA250)
	Insulation resistance	20 MΩ or higher (500 VDC)
	Ambient light	Incandescent lamp: 5,000 lux or lower, Sunlight: 20,000 lux or lower
	Ambient temperature	-25 to +55 °C -13 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-25 to +75 °C -13 to 167 °F
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: SUS316L, indicator cover/lens cover: polysulfone, cord protector: polymethylpentene, filler: polyester-based resin
Accessories		Instruction manual
Weight		Approx. 90 g

Keyence FD-MZ10ATKP Keyence

$2,555.90

Only 3 units left

Specifications

Model		FD-MZ10ATKP^*1
Type		Vertical
Shape		Built-in amplifier
Rated flow range		0.14 - 2.60 G/min (0.50 - 10 L/min)^*1
Possible display range		0.14 - 6.35 G/min (0.50 - 30 L/min)^*2
Possible ranges to set		0 - 6.35 G/min (0 - 30 L/min)
Connection port		NPT3/8 (10 A)
Detectable fluids		Water or non-corrosive liquid
Conductivity of detection fluids		5 µS/cm or higher
Detection fluid temperature		0 to +85°C 32 to 185 °F (No freezing)
Pressure loss		Max. 1.45 PSI (0.01 MPa)
Display method		Dual row display with 4-digit, 7 segment LED, bar display (2 colors), output indicators, flow indicator
Display resolution		0.01/0.1 (G/min, L/min) selectable
Repeatability		0.5 s : ±5% of F.S., 1 s : ±3.5% of F.S., 2.5 s : ±2.5% of F.S., 5 s : ±1.6% of F.S., 10 s : ±1% of F.S., 30 s : ±0.8% of F.S., 60 s : ±0.6% of F.S.^*3
Hysteresis		Variable
Response time (chatter prevention feature)		0.5 s/1 s/2.5 s/5 s/10 s/30 s/60 s variable
Accumulated flow unit		0.01/0.1/1/10/100 (G, L) selectable
Integration data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length : 10 years or longer, Data read/write frequency : 1 million times or more)
Control output/Accumulation pulse output/ Error alarm output		PNP open collector, max. 100 mA/ch^*4 30 V or less, residual voltage 1 V or less, 3 outputs (N.O./N.C. switchable)
Analog output		4-20 mA, max. load resistance 260 Ω Analog output range can be set to any value
Integration reset/bank switch input/flow zero function input		Input time : 20 ms or greater,Select either the accumulation output or the accumulation pulse by setting the mode
Minimum flow volume		0.14 G/min (0.50 L/min)^*5
Power consumption (Current consumption)		Normal : 1700 mW (70 mA), Power save : 1000 mW (40 mA)
Rating	Power voltage	24 VDC, Ripple (P-P) 10 % or less, Class 2
Environmental resistance	Enclosure rating	IP65
	Pressure resistance	290 PSI (2.0 MPa)
	Applied pressure range	Max. 145 PSI (1.0 MPa)
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material	Liquid end materials	Bore : SCS13, Measurement pipe : PPS, O ring : fluoro-rubber (FKM)
	Other materials	Plastic case areas : PPS, Metal case areas : SUS430, Cable : PVC
Accessory		Instruction Manual, Connector cable (2.7 m 106.3")
Weight		Approx. 865 g
^1 The rated flow range indicates recommended operating range. ^2 Can be used within the display range as well as within the rated flow range. ^3 The repeatability for FD-MZ10ATK (P)/YK (P) in the range of 5.20 to 7.50 G/min (20 to 30 L/min) is the double of the value listed in the table. The repeatability is the error of the detection point when fluids flow repeatedly under the same conditions. ^4 Maximum 20 mA for alarm output. ^*5 Durchfluss unterhalb des Mindest-Durchflusses wird als 0 l/min angezeigt.

Keyence CB-B5E Keyence

$1,311.21

Only 2 units left

Specifications

Model		CB-B5E^*1
Type		Head extension cable
Cable min. bending R		22 mm 0.87"
Cable length		5 m 16.4'
Environmental resistance	Enclosure rating	IP67 (IEC60529)^*2
Material		PVC
Weight		Approx. 400 g
^1 Regarding cable extension between the head and controller: Up to 2 cables can be connected with the CB-BxxE, and these cables should be kept to a total length of 30 m 98.4' or less. ^2 This value is from a case in which the sensor head has been connected. However, the controller side connector is not included.

Keyence FU-39 Keyence

$0.00

Sold Out

Specifications

Model		FU-39
Type		Small diameter
Standard detection object		30² mm 1.181" x 1.181" white mat paper (FS2-60, FS2-62), 10² mm 0.393" x 0.393" white mat paper (FS-65)
Fibre unit length		90 mm3.543"
Minimum bend radius		R10 mm0.394"
Minimum detectable object		Gold wire with a diameter of 0.01 mm0.0004"
Hysteresis (of detecting distance)		20% max.
Environmental resistance	Ambient temperature	-30 to +100 °C -22 to 212 °F
	Relative humidity	35 to 85 % RH
Material		Glass
Weight		Approx. 2 g

Keyence CA-LHR50 Keyence

$1,387.36

Only 7 units left

Specifications

Model				CA-LHR50
Focal point				50 mm 1.97"
F-stop range (aperture)				F2.8 to F16
Minimum WD				0.1 m 0.3'
Mount				C-mount
Filter size				30.5 mm 1.20" P0.5
Compatible image sensor size				2/3"
TV distortion				-0.02 % (0.02 %)^*1
Resolving power				200 cycles/mm at center, 140 cycles/mm on periphery
Ambient temperature/humidity range				0 to +50°C 32 to 122°F, 80% RH or less (No condensation)
Lens coating				WIDE, BAND MULTICOATING
Weight				Approx. 170 g
^*1 Indicates specification for compatible image sensor size. Value in parenthesis applies to 1/3" image sensor size.

Keyence KV-10R Keyence

$480.88

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-42106 Keyence

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence ER-GL12TPC Keyence

$0.00

Sold Out

Specifications

Model		ER-GL12TPC ^1 ^2
Type		General-purpose all-metal shielded type Screw type M12 Connector (M12 4-pin) PNP output Long-Range
Power supply cable length		― ^*3
No. of control outputs		2
Output mode	Output 1	N.O.
	Output 2	N.C.
Button		None
Button	Function	―
Detecting distance		7 mm 0.28" ±10% ^*4
Response frequency		100 Hz ^5 ^6
Hysteresis distance		15% or less of detecting distance
Detectable object		Magnetic metal, Non-magnetic metal ^*7
Standard detectable object (Iron, t = 1 mm 0.04")		21 × 21 mm 0.83" × 0.83"
Temperature characteristics		±10% or less of detecting distance at +25°C +77°F (-25 to +55°C -13°F to +131°F) ±15% or less of detecting distance at +25°C +77°F (+55 to +70°C 131°F to 158°F)
Control output		Open-collector, 30 VDC or less; 50 mA or less for 1 output; 50 mA or less in total for 2 outputs
Control output	Residual voltage	PNP output: 2.2 V or less (Output current: 10 mA or less) / 2.3 V or less (Output current: 10 to 50 mA) ^*8
Power supply	Power voltage	16 to 30 VDC (including 10% or less ripple (P-P)), Class 2
	Power consumption (excluding load current)	1000 mW or less (42 mA or less at 24 V, 63 mA or less at 16 V) ^*9
Protection circuit		Protection against reverse power connections, output short-circuits, and reverse output connections
Environmental resistance	Enclosure rating	IP67 (IEC60529), IP67G (JIS C 0920)
	Ambient temperature	-25 to +70°C -13°F to +158°F (no freezing) ^*10
	Relative humidity	Up to 95% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	1000 m/s² 3280.8 ft/s² (100 G), 10 times in each of the X, Y, and Z directions
Material		Detecting surface: SUS303, Mounting screw: SUS303 (M30: SUS304), Case resin: PBT, Nut: SUS304, Toothed lock washer: SUS304 [Connector] Indicator: PBT (M8: LCP), Connector: PBT (M8: LCP), Case: SUS303 [Connector with pigtail] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC, Connector resin: TPU, Connector metal: Nickel-plated brass [Cable] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC
Accessories		Nut ×2, Toothed lock washer ×1
Weight		Approx. 35 g 1.24 oz
^1 Supports IO-Link specification v1.1/COM2 (38.4 kbps). ^2 Long-body type. See “Dimensions” for details. ^3 Ensure the power cable is no longer than 30 m 98.4' for connector and connector with pigtail types and no longer than 20 m 65.6' with IO-Link connections. ^4 The distance at which a standard detectable object can be detected when the unit is mounted without being affected by surrounding metal. ^5 Value when a standard detectable object is used, the distance between detectable objects is twice the standard detectable object, and the distance to the detectable object is 1/2 the detecting distance. ^6 The response frequency varies depending on the operating temperature. The response frequency at temperatures of +55°C +131°F or higher is 50% of that at +25°C +77°F. ^7 Detecting distance varies according to the material and size. See the characteristic diagrams for details. ^8 Residual voltage is for when a 2 m 6.6' cable is used. ^9 For IO-Linkcompatible devices listed under 1, power consumption is as follows. M8 type: 840 mW or less (35 mA or less at 24 V, 53 mA or less at 16 V) M12 type: 1090 mW or less (46 mA or less at 24 V, 69 mA or less at 16 V) M18, M30 type: 1250 mW or less (53 mA or less at 24 V, 79 mA or less at 16 V) ^*10 The upper limit of the UL temperature rating is +55℃ +131℉.

Keyence KV-C64TA Keyence

$666.57

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-83206 Keyence

$0.00

Sold Out

Specifications

Model				OP-83206
Overview				Front protective cover protecting detection side of light curtain.
Applicable product				SL-V104H, SL-V52L
Number included				1 pcs.
Length				2,070.2 mm 81.5"
Material				Translucent plastic: Polycarbonate Black plastic: ABS
Note				To install this product on both the transmitter and receiver, 2 sets are required. Use the dimming filters (sold separately) by attaching them to the front protection cover. When the front protection cover is attached, the L-shaped mounting bracket (OP-42

Keyence KV-SH04PL Keyence

$1,112.49

Only 9 units left

Specifications

Model		KV-SH04PL
Type		High-speed positioning unit
No. of control axes		4 axes
Input		Positive (negative) direction limit switch, origin sensor, stop sensor, continuous instant starting, 1 point per axis for 4 points in total, 24 VDC input possible Forced stop input, 1 point shared by whole axes, 24 VDC input possible Z-phase input (+) (-), servo end, servo ready, drive alarm, 1 point per axis for 4 points in total, 5 VDC input possible
Output		Pulse output (differential line driver): equivalent to AM26C31 (max. 20 mA), Pulse output (open collector): rated load: 30 VDC, 0.1 A or less Drive alarm reset, servo ON, deviation counter clear, rated load: 30 VDC, 0.1 A or less
Output frequency		1 Hz to 8 MHz
Output format		Differential line driver output/open collector output (switched per axis via hardware switch) (1-pulse mode/2-pulse mode/2-phase 1-multiplication/2-phase 2-multiplication/2-phase 4-multiplication)
Control mode		Standard mode, High-speed mode
Control period		Standard mode: 500 μs, High-speed mode: 62.5 μs
Starting time		Standard mode: 500 μs or more, High-speed mode: 8 μs or more (continuous instant starting: 1 μs)
Basic operation		Standard mode: Origin return/JOG, linear interpolation (2 to 4 axes), position control (ABS/INC), speed control (+/- direction) High-speed mode: Origin return/JOG, position control (ABS/INC), speed control (+/- direction)
Function		Standard mode: Speed change, target change, stop sensor, speed override, stop at specified angle, continuous operation interrupt, forced next point, absolute position follow-up control, sync type follow-up control High-speed mode: Speed change, target change, stop sensor, continuous instant starting
Position unit		Standard mode: mm, deg (angle), PLS (pulse count), decimal place 0 to 9, unit conversion function High-speed mode: PLS (pulse count)
Positioning control	Position setting range	-2147483648 to 2147483647
	Acceleration/deceleration curve	Standard mode: Linear, SIN High-speed mode: Linear
	Acceleration/deceleration rate	Acceleration/deceleration individual setting
	Acceleration/deceleration time	Standard mode: 0 to 65535 ms
	M-code	0 to 65000, WITH/AFTER mode
	Number of points	100 points/axis
Origin return	Origin return method	Dog type (“With Z phase” or “Without Z phase” can be selected by pushing the button), Dog type inching (“With Z phase” or “Without Z phase”)^*1, origin sensor (edge/midpoint/Z-phase), limit switch edge, immediate Z-phase origin return, data set type
JOG/inching		Inching (number of pulses can be specified)^*1, JOG
Teaching		Current coordinate teaching
24 V power input (I/O)		24 VDC (-15%/+20%)
5 V power output		5 VDC (±10%), 200 mA or less
Others		Multi-axis simultaneous starting based on unit interrupt/inter-unit synchronization
Internal current consumption		200 mA or less, external I/O: 260 mA or less
Weight		Approx. 230 g
^*1 High-speed mode cannot be set.

Keyence OP-66848 Keyence

$0.00

Sold Out

Specifications

Model				OP-66848
Overview				Expansion cable for transmitter side of thrubeam unit.
Applicable product				LV-S Series thrubeam
Cable end				Loose wire
Length				20 m 65.62' roll

Keyence SZ-VU32NC Keyence

$0.00

Sold Out

Specifications

Model				SZ-VU32NC
Type				CIP Safety™ type
Weight				Approx. 600 g

Keyence OP-88350 Keyence

$191.84

Only 10 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence MU-CC4 Keyence

$0.00

Sold Out

Specifications

Model				MU-CC4
Type				Power cable
Applicable product				MU-N Series
Cable end				Cable end: M12 4-pin straight, Controller side: Connector
Length				0.3 m 0.98'
Material				PVC (Polyvinyl chloride)
Note				Main unit
Weight				Approx. 30 g

Keyence SV3-M005AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-M005AK
General specifications	Applicable servo amplifier			SV3-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*1
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0457 ×10^-4 kg·m²
	Rated power rating			5.53 kW/s
	Rated angle acceleration			34,700 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.3 kg 10.58 oz
^*1 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence GL-R32H Keyence

$817.61

In stock, 12 units

Specifications

Model			GL-R32H
Detection capability			ø0.98" ø25 mm
Total length			25.20" 640mm
No. of beam			32
Detection height			24.41" 620mm
Protection height			26.18" 665mm
Beam axis spacing/Lens diameter			20 mm / ø5 0.79" / ø0.20"
Detecting distance			0.66 to 49.21' 0.2 to 15 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	7.9
		OFF→ON	50.6^*2
		All blocked→ON	68.3^*3
	Optical synchronization system (Channel A or B)	ON→OFF	10.9
		OFF→ON	55.1^*2
		All blocked→ON	80.2^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	61
		Receiver	74
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		880 g
	Receiver		890 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence MD-V9900WA Keyence

$4,559.98

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SZ-V32NC Keyence

$2,899.99

Only 5 units left

Specifications

Model				SZ-V32NC ^*1
Type				Network Type (CIP Safety)
Detection capability	Minimum detectable object size			Diameter 20, 30, 40, 50, 70, 150 mm 0.79", 1.18", 1.57", 1.97", 2.76", 5.91" (depends on the setting) Reflectance 1.8% min., Speed 1.6 m/s 5.25 ft/s max. ^*2
	Detectable angle			190° ( -5° to 185° )
	Response time (ON to OFF)	Standard Mode	Scan Cycle A	160 ms (2scans) to 1280 ms (16scans) ^3 ^4
			Scan Cycle B	168 ms (2scans) to 1344 ms (16scans) ^3 ^4
			Scan Cycle C	176 ms (2scans) to 1408 ms (16scans) ^3 ^4
		High Speed Mode	Scan Cycle A	80 ms (2scans) to 640 ms (16scans) ^3 ^4
			Scan Cycle B	84 ms (2scans) to 672 ms (16scans) ^3 ^4
			Scan Cycle C	88 ms (2scans) to 704 ms (16scans) ^3 ^4
	Response time (OFF to ON)			Response time (ON to OFF) + 150 ms
	Protection zone	Minimum detectable object size: 70 / 150 mm 2.76" / 5.91"		8.4 m 27.56' (Standard Mode) 5.7 m 18.70' (High Speed Mode)
		Minimum detectable object size: 50 mm 1.97"		5.6 m 18.37' (Standard Mode) 3.8 m 12.47' (High Speed Mode)
		Minimum detectable object size: 40 mm 1.57"		4.3 m 14.11' (Standard Mode) 2.9 m 9.51' (High Speed Mode)
		Minimum detectable object size: 30 mm 1.18"		2.9 m 9.51' (Standard Mode) 2.0 m 6.56' (High Speed Mode)
		Minimum detectable object size: 20 mm 0.79"		1.6 m 5.25' (Standard Mode) 1.1 m 3.61' (High Speed Mode)
	Warning zone	Minimum detectable object size: 70 / 150 mm 2.76" / 5.91"		26 m 85.30' (Standard Mode) 23 m 75.46' (High Speed Mode) ^*5
		Minimum detectable object size: 50 mm 1.97"		25 m 82.02' (Standard Mode) 21 m 68.90' (High Speed Mode) ^*5
		Minimum detectable object size: 40 mm 1.57"		24 m 78.74' (Standard Mode) 20 m 65.62’ (High Speed Mode) ^*5
		Minimum detectable object size: 30 mm 1.18"		23 m 75.46' (Standard Mode) 18 m 59.06' (High Speed Mode) ^*5
		Minimum detectable object size: 20 mm 0.79"		21 m 68.90' (Standard Mode) 15 m 49.21' (High Speed Mode) ^*5
	Additional safety distance			100 mm 3.94" ^*6
	Maximum measurement distance			60 m 196.85' ^*7
Maximum number of banks				Max.16 banks
Multiple scanner heads				Max. 3 scanner heads
Camera monitoring area				Monitor area: over 190° (-5° to 185°) ^*8
Display				QVGA 2.2inch color LCD
Light source	Type, wavelength			Infrared laser diode, 905 nm
	Laser Class	IEC		Class1 IEC/EN60825-1
		FDA		Class1 FDA 21CFR 1040.10, 1040.11 (Laser Notice) ^*9
		JIS		Class1 JIS C6802
Control output (OSSD)	Output			-
	Number of outputs
	Max. load current
	Residual voltage (during ON)
	OFF-state voltage
	Leakage current
	Max. capacitive load
	Load wiring resistance
Inputs	PNP
	NPN
Non-safety related output (AUX output)	Output type
	Number of outputs
	Max. load current
	Residual voltage (during ON)
	Muting lamp
Interface	USB			USB2.0
	Ethernet	Standard		IEEE802.3u (100 BASE-TX)
		Transmission rate		100 Mbps
		Cable		STP(Shielded Twisted Pair) cable or UTP(Unshielded Twisted Pair) cable. Category5 or higher.
		Connector		RJ45 (IP65) 2 ports
Network function				CIP Safety, EtherNet/IP™, UDP
Cable length	Power and I/O cable			30 m 98.43' or less ^*10
	Between scanner head and display unitc			20 m 65.62' or less each ^*11
	Ethernet cable			100 m 328.08' or less ^*12
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1 (Type 3 ESPE)
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 3 ESPE), IEC61496-3, EN61496-3 (Type 3 AOPDDR), IEC61508, EN61508, EN ISO13849-1, 2015 (PLd, Category3), UL508, UL1998, CSA C22.2 No.14, CSA C22.2 No.0.8
Rating	Power consumption			13.4 W
	Power voltage			24 VDC ±10% (Ripple P-P 10% or less): When using a converter power supply, 24 VDC +20%/-30%: When using a battery
Environmental resistance	Enclosure rating			IP65(IEC60529)
	Ambient light			Incandescent lamp: 1500 lux or less ^*13
	Operating ambient temperature			-10 to +50°C 14 to 122°F (No freezing)
	Operating relative humidity			35% to 85% RH (No condensation)
	Storage temperature			-25 to +60°C -13 to +140°F (No freezing)
	Storage relative humidity			35% to 95% RH
	Vibration resistance			10 to 55 Hz, 0.7 mm 0.03" compound amplitude, 20 sweeps each in X, Y, and Z directions
	Shock resistance			100 m/s² 328.08 ft/s² (Approx. 10 G) 16 ms pulse, in X, Y, Z directions 1000 times each axis
Material	Scanner head	Main unit case		Magnesium
		Window		Polycarbonate, PEI
		Indicator part		Aluminum, PES
	Display unit	Case		Magnesium, PPS, Polycarbonate
	System memory			Aluminum, PPE
Weight				Approx. 2300 g
^1 Integrated models include display unit, scanner head, system memory and a connection cable (SZ-VS005). ^2 If the object to be detected moves parallel to the detection plane, SZ-V cannot detect the object moving at speed over 1.6 m/s 5.25 ft/s, regardless of the encoder setting. ^3 The response time, protection zone, and warning zone are affected by the operation mode. ^4 When using PROFIsafe, 6 ms is added to the response time. When using CIP Safety, 10ms is added to the response time. ^5 20% or more reflectance is necessary for the minimum detectable object in the warning zone. ^6 If there is a highly reflective background within 1.5 m 4.92' from the boundary of the protection zone, 200 mm 7.87" must be added as supplementary necessary distance to the protection zone when calculating the minimum safety distance. ^7 Even when using the network data output, the maximum measured output distance is 60 m 196.85'. ^8 Only applicable for the type with a camera. ^9 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^10 10 m 32.81' or less when supplying power from a battery. ^11 When supplying power from a battery, the length of each connection cable should be 10 m 32.81' or less when using two scanner heads, and 5 m 16.40' or less when using three scanner heads. ^12 Distance between SZ-V and Ethernet switch. ^*13 An ambient light source should not be located within ±5° of the detection plane.

Keyence SV-C5E Keyence

$0.00

Sold Out

Specifications

Model				SV-C5E
Type				Motor power cable, Standard
Length				5 m 16.4'
Note				for 2 kW motor

Keyence CA-DBB5 Keyence

$442.89

Only 5 units left

Specifications

Model				CA-DBB5
Type				Bar Light
LED color				Blue
Diffusion plate				OP-42283
Polarizing plate				OP-42281
Power consumption				2.9 W
Input voltage				12 VDC
Weight				Approx. 40 g

Keyence NR-HA08 Keyence

$2,560.29

Only 9 units left

Specifications

Model		NR-HA08 ^*1
Type		High-speed analog measurement unit
Input method		Single-ended input / Balanced differential input selection Channels not insulated from each other, input channels insulated from other units (PC)
Number of channels		Single-end: 8 ch^2 (Differential: 4 ch) / Current: 4 ch^3
Measurement cycle		Maximum sampling cycle: 1 μs (1 MHz) to 60 s
A/D converting system		Successive approximation
A/D resolution		14 bit
Input frequency band		250 kHz (−3 dB typ.)
Input impedance	Voltage	1 MΩ ±1%
	Current	250 Ω ±1%
Withstand voltage	Input to system bus	300 VAC (50/60 Hz), 1 minute
Input type	Voltage	±10 V, ±5 V, ±2.5 V, ±1 V, ±0.5 V, ±0.25 V
	Current	±20 mA
Maximum input rating	Voltage range	±30 V
	Current range	±30 mA
Measurable range		±10 V: −11.000 to +11.000 V ±5 V: −5.500 to +5.500 V ±2.5 V: −2.7500 to +2.7500 V ±1 V: −1.1000 to +1.1000 V ±0.5 V: −550.0 to +550.0 mV ±0.25 V: −275.00 to +275.00 mV ±20 mA: −22.000 to +22.000 mA
Measurement accuracy	Zero-point accuracy	±0.03% of F.S.
	DC amplitude accuracy	±0.1% of F.S. (10 V/5 V/2.5 V/20 mA range at 16 averages, 1 V/0.5 V/0.25 V range at 128 averages)
Display resolution		±10 V: 1 mV ±5 V: 1 mV ±2.5 V: 0.1 mV ±1 V: 0.1 mV ±0.5 V: 0.1 mV ±0.25 V: 0.01 mV ±20 mA: 1 μA
Buffer memory		4M data^*4
Warm up time		15 minutes or more
Rating	Power consumption	3.3 W or less
Environmental resistance	Ambient temperature	0 to +40°C 32°F to 104°F
	Relative humidity	10 to 85% RH (no condensation)
Weight		Approx. 150 g 5.30 oz
^1 The above specifications are the values when zero point adjustment is performed after the warm-up period in an environment with a temperature of 23°C ±3°C 73.4°F ±5.4°F. ^2 Voltage input is 4 ch max. when current input is used. ^3 Max. expansion: 432 ch (with 54 units connected, using NR-X100W), 48 ch (with 6 units connected, using NR-500) ^4 Limited by the NR-X100W buffer memory when using the NR-X100W.

Keyence OP-87640 Keyence

$585.26

Only 5 units left

Specifications

Model				OP-87640
Applicable product				M12 connector sensor
Number included				1
Cable end				Sensor side: M12 4-pin L-shape, Cable end: Loose wires
Length				2 m 6.56'
Material				PUR (Polyurethane)
Weight				Approx. 70 g

Keyence SV-T1 Keyence

$0.00

Sold Out

Specifications

Model				SV-T1
Type				Terminal kit
Note				For 2/3 kW