Distance & Measurement Sensors

$301.16

Only 6 units left

Specifications

Model		LR-XN11N
Type		NPN Output
Cable/Connector		Cable
Main Unit/Expansion Unit		Main Unit
No. of Control Outputs		2
No. of External Inputs		1
Response Time		500 µs^*1/1 ms/3 ms/10 ms/200 ms Selectable
IO-Link		—
Functions	Timer Function	Timer OFF/Off-delay/On-delay/One-shot/On-Off delay/On-delay One-shot
I/O	Control Output	Open collector, 30 VDC or lower, N.O./N.C. When used as a solitary unit: 100 mA or lower for 1 output; 100 mA or lower in total for 2 outputs; When expanding with multiple units: 50 mA or lower for 1 output Residual voltage NPN: 1.4 V or lower (output current: 10 mA or lower)/2 V or lower (output current: 10 to 100 mA)
	External Input	External Set/Laser OFF/Zero Shift/Hold Reset/Gyro Alert RST selectable Short circuit current - NPN: 1 mA or lower Input time: 3 ms or more ON, 20 ms or more OFF (25 ms or more ON, 25 ms or more OFF only when External Set is selected)
Unit Expansion		Up to 8 expansion units possible (including main unit, a total of 9 units connected) However, up to 16-unit expansion is possible when the LR-XN10 is used for expansion with the NU Series.
Protection Circuit		Protection against reverse power connection, protection against output overcurrent, protection against output surge, protection against reverse output connection
Number of Interference Prevention Devices		OFF/4 units/8 units selectable^*2
Power supply	Power voltage	16 to 30 VDC^*3 (including 10% ripple (P-P) or less), class 2
	Power consumption	During normal operation: 1060 mW (44 mA or lower at 24 V, 61 mA or lower at 16 V), ECO ON/ALL: 895 mW (37 mA or lower at 24 V, 50 mA or lower at 16 V) (excluding Load Current)
Environmental resistance	Ambient temperature	−20 to +55°C -4°F to 131°F (no freezing)^*4
	Relative humidity	35 to 85% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power Spectral Density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	500 m/s² (50G); 3 times each for X, Y, and Z axes
Case Material		Main Unit and Cover: Polycarbonate
Accessories		Instruction manual
Weight		Approx. 80 g
^1 If 500 µs is selected, the following limitations apply. · Only 2-point calibration can be performed. · The detection range masking is set during calibration. (Manual setting of the masking range is not supported.) · Output 2 is limited to an alarm output for errors and gyro issues, and standard/area cannot be used. · The interference prevention function is not supported ^2 Selecting four or eight interference prevention units causes the response time to change as follows: 4 Units selected: 6 ms/18 ms/60 ms/1.2 s selectable; 8 Units selected: 12 ms/36 ms/120 ms/2.4 s selectable. ^3 When expanding the system with 4 or more expansion units, use a power voltage of 20 V or higher. ^4 Expansion by 1 or 2 units: −20 to +55°C -4°F to 131°F; Expansion by 3 to 10 units: -20 to +50°C -4°F to 122°F, Expansion by 11 to 16 units: -20 to +45°C -4°F to 113°F

Keyence LJ-X8400 Keyence

$14,272.94

Only 5 units left

Specifications

Model			LJ-X8400
Reference distance			380 mm 14.96"
Measurement range	Z-axis (height)		±60 mm ±2.36" (+95 to -220 mm +3.74" to -8.66" ^*1) (F.S.=315 mm 12.40")
	X-axis (width)	NEAR side	180 mm 7.09" (163 mm 6.42" ^*1)
		Reference distance	210 mm 8.27"
		FAR side	240 mm 9.45" (320 mm 12.60" ^*1)
Light source			Blue semiconductor laser
Light source	Wavelength		405 nm (visible light)
	Laser class		Class 2M laser product (IEC60825-1, FDA (CDRH) Part 1040.10 ^2) ^3
	Output		10 mW
Spot size			Approx. 275 mm × 249 μm 10.83" × 0.0098" (reference distance)
Repeatability	Z-axis (height)		5 μm 0.000197" ^4^5
	X-axis (width)		10 μm 0.0004" ^4^6
Linearity	Z-axis (height)		Reference distance: ±60 mm ±2.36" ±0.025% of F.S. (±0.003%) Total range: ±0.035% of F.S. (±0.005%) ^*7
Profile data interval	X-axis (width)		75 μm 0.0030" (50 μm 0.0020"~) 100 μm 0.0039" (50 μm 0.0020"~) ^1 ^8
Profile data count			3200 points
HDR (high dynamic range)			Single-shot HDR ^*9
Laser irradiation position confirmation function	Light source		Blue LED (405 nm)
Temperature characteristic			0.01% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10,000 lux or less ^*11
	Ambient temperature		0 to +45°C 32 to +113°F ^*12
	Relative humidity		85% RH or less (no condensation)
	Vibration resistance		10 to 57 Hz, double amplitude 1.5 mm 0.06"; 3 hours each for X, Y, and Z axes
	Shock resistance		15 G / 6 msec
Material			Aluminum
Weight			Approx. 1300 g 2.87 lb
^1 When range is extended. ^2 Classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^3 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^4 Values measured by averaging 4096 times at the reference distance. ^5 The measured target is a KEYENCE standard target. Value when the average height of the default setting area is measured with height and position tools. All other settings are default values. ^6 The measured target is a pin gauge. Value when the point of intersection for the pin gauge rounded surface and edge level is measured using height and position tools. All other settings are default values. ^7 The measured target is a KEYENCE standard target. Profile data when measured by smoothing 64 times and averaging 8 times. All other settings are default values. Values inside parentheses are representative examples of averages for all profile data. ^8 The profile data interval can be changed. If changed, the measurement range in the X direction will also change. ^9 A characteristic that allows for stable, high-precision measurement with a single capture (exposure) at all levels of reflectance, from black (low) to glossy surfaces (high). ^10 The value when a head cable (CB-B) or extension cable (CB-BE) is connected. Does not include CB-B*L connection. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^*12 The head needs to be mounted to a metal plate to be used.