keyence

Showing 6385 - 6408 of 6950 products

$0.00

Sold Out

Specifications

Model				SV3-020L2
General specifications	Capacity			200 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 0.8 kg 28.22 oz
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single-phase 200 V/DC 270 V
	Max. applicable motor capacity			200 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 0.5 kVA Single-phase 200 V: 0.6 kVA DC 270 V: 0.5 kVA
	Output current	Continuous		1.6 Arms
		Max.		5.9 Arms
	Main circuit power loss			Three-phase 200 V: 11.9 W Single-phase 200 V: 12.1 W DC 270 V: 9.8 W
	Regenerative resistor power loss			―
	Control circuit power loss			12 W
	Total power loss			Three-phase 200 V: 23.9 W Single-phase 200 V: 24.1 W DC 270 V: 21.8 W
	Rated input current	Main circuit		Three-phase 200 V: 1.3 Arms Single-phase 200 V: 2.4 Arms DC 270 V: 1.5 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		29 A ^*3
		Control circuit		34 A ^*3
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-040L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-040L2
General specifications	Capacity			400 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 1.1 kg 2.43 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single-phase 200 V/DC 270 V
	Max. applicable motor capacity			400 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 1.0kVA Single-phase 200 V: 1.2kVA DC 270 V: 1.0kVA
	Output current	Continuous		2.8 Arms
		Max.		9.3 Arms
	Main circuit power loss			Three-phase 200 V: 22.5 W Single-phase 200 V: 23.7 W DC 270 V: 17.5 W
	Regenerative resistor power loss			―
	Control circuit power loss			12 W
	Total power loss			Three-phase 200 V: 34.5 W Single-phase 200 V: 35.7 W DC 270 V: 29.5 W
	Rated input current	Main circuit		Three-phase 200 V: 2.5 Arms Single-phase 200 V: 5.0 Arms DC 270 V: 3 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		29 A ^*3
		Control circuit		34 A ^*3
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-075L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-075L2
General specifications	Capacity			750 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 1.6 kg 3.53 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single-phase 200 V/DC 270 V
	Max. applicable motor capacity			750 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 1.6 kVA Single-phase 200 V: 1.9 kVA DC 270 V: 1.6 kVA
	Output current	Continuous		5.5 Arms
		Max.		16.9 Arms
	Main circuit power loss			Three-phase 200 V: 38.9 W Single-phase 200 V: 39.2 W DC 270 V: 30.7 W
	Regenerative resistor power loss			Three-phase 200 V: 15 W Single-phase 200 V: 15 W DC 270 V: ―
	Control circuit power loss			14 W
	Total power loss			Three-phase 200 V: 52.9 W Single-phase 200 V: 53.2 W DC 270 V: 44.7 W
	Rated input current	Main circuit		Three-phase 200 V: 4.1 Arms Single-phase 200 V: 8.7 Arms DC 270 V: 4.9 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A ^*3
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-100L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-100L2
General specifications	Capacity			1.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 1.6 kg 3.53 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/DC 270 V
	Max. applicable motor capacity			1.0 kW
	Power supply capacity for 1 amplifier			2.3 kVA
	Output current	Continuous		7.6 Arms
		Max.		17 Arms
	Main circuit power loss			Three-phase 200 V: 49.2 W DC 270 V: 38.7 W
	Regenerative resistor power loss			Three-phase 200 V: 15 W DC 270 V: ―
	Control circuit power loss			14 W
	Total power loss			Three-phase 200 V: 63.2 W DC 270 V: 52.7 W
	Rated input current	Main circuit		Three-phase 200 V: 5.7 Arms DC 270 V: 6.9 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A ^*3
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-150L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-150L2
General specifications	Capacity			1.5 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 2.1 kg 4.63 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/DC 270 V
	Max. applicable motor capacity			1.5 kW
	Power supply capacity for 1 amplifier			3.2 kVA
	Output current	Continuous		11.6 Arms
		Max.		28 Arms
	Main circuit power loss			Three-phase 200 V: 72.6 W DC 270 V: 55.8 W
	Regenerative resistor power loss			Three-phase 200 V: 30 W DC 270 V: ―
	Control circuit power loss			15 W
	Total power loss			Three-phase 200 V: 87.6 W DC 270 V: 70.8 W
	Rated input current	Main circuit		Three-phase 200 V: 7.3 Arms DC 270 V: 11 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A ^*3
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-200L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-200L2
General specifications	Capacity			2.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 2.8 kg 6.17 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/DC 270 V
	Max. applicable motor capacity			2.0 kW
	Power supply capacity for 1 amplifier			4.0 kVA
	Output current	Continuous		18.5 Arms
		Max.		42 Arms
	Main circuit power loss			Three-phase 200 V: 104.2 W DC 270 V: 82.7 W
	Regenerative resistor power loss			Three-phase 200 V: 30 W DC 270 V: ―
	Control circuit power loss			16 W
	Total power loss			Three-phase 200 V: 120.2 W DC 270 V: 98.7 W
	Rated input current	Main circuit		Three-phase 200 V: 10 Arms DC 270 V: 14 Arms
		Control circuit		0.25 Arms
	Rush current	Main circuit		34 A ^*3
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-300L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-300L2
General specifications	Capacity			3.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 2.8 kg 6.17 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/DC 270 V
	Max. applicable motor capacity			3.0 kW
	Power supply capacity for 1 amplifier			5.9 kVA
	Output current	Continuous		19.6 Arms
		Max.		56 Arms
	Main circuit power loss			Three-phase 200 V: 114.2 W DC 270 V: 83.5 W
	Regenerative resistor power loss			Three-phase 200 V: 30 W DC 270 V: ―
	Control circuit power loss			16 W
	Total power loss			Three-phase 200 V: 130.2 W DC 270 V: 99.5 W
	Rated input current	Main circuit		Three-phase 200 V: 15 Arms DC 270 V: 20 Arms
		Control circuit		0.25 Arms
	Rush current	Main circuit		34 A ^*3
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*4)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*5
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^5 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-500L2 Keyence

$0.00

Sold Out

Specifications

Model				SV3-500L2
General specifications	Capacity			5.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single-phase^1) 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^2
			Control circuit	Single-phase 200 to 240 VAC (-15%/+10%), 50/60 Hz, 270 to 324 VDC^*2
		Allowable frequency fluctuation	Main circuit/control circuit	±5% max.
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, Sine wave current drive system
	Feedback			Serial encoder (absolute) communication, Fully closed control serial communication, Analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20:SV3-005L2/010L2/020L2/040L2/075L2/100L2/150L2 IP10:SV3-200L2/300L2/500L2
			Pollution degree	2 (in an IP54 or higher control panel) However, the product must be used in the following environments: • No corrosive or flammable gases • No exposure to water, oil, or chemicals • No dust
		Operating ambient temperature		-5 to +60°C 23 to 140°F (No freezing) (reduced ratings at +55°C 131°F or higher)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (No freezing)
		Operating/storage ambient temperature		95% RH or less (No condensation)
		Altitude		No more than 2,000 m 6,561.7' above sea level (reduced ratings at 1,000 m 3,280.8' or higher)
		Vibration resistance		4.9 m/s² 16.1 ft/s² (Compliant with JIS C60068-2-6)
		Impact resistance		19.6 m/s² 64.3 ft/s² (Compliant with JIS C60068-2-27)
		Other		No static noise, strong electric or magnetic fields, or radiation
	Applied standard	UL/CSA standards		UL 61800-5-1, CSA 22.2 No. 274
		CE marking	Machinery Directive	EN 61800-5-1, EN 61800-5-2, EN ISO 13849-1:2015 Cat. 3 PLe, EN IEC 62061 Maximum SIL3
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Structure	Type		Base mount installation
	Safety function			STO function (STO/EN 61800-5-2)
	Safety function	Safety parameters		SIL 3 / EN 61508, Maximum SIL 3 / EN IEC 62061, PLe (Category 3) / EN ISO 13849-1:2015
		Response time		4 ms(max)
		Input		STO1, STO2: Power module base block signals Internal impedance: 5.1 kΩ Operable voltage range: +24 V, ±20% Max. delay time: 4 ms (Time from when STO1 and STO2 are turned off until motor current is interrupted)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 4 ms (Time from STO1 and STO2 change to EDM change)
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative error, etc.
	Min. insulation resistance			500 VDC 1 MΩ or more with insulation resistance meter
	Insulation withstand voltage			1,500 VAC or more (between primary side and ground) 3,000 VAC or more (between primary and secondary) 350 VAC: between secondary circuit and ground
	Weight			Approx. 4.4 kg 9.70 lb
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/DC 270 V
	Max. applicable motor capacity			5.0 kW
	Power supply capacity for 1 amplifier			7.5 kVA
	Output current	Continuous		32.9 Arms
		Max.		84 Arms
	Main circuit power loss			Three-phase 200 V: 226.6 W DC 270 V: 146.2 W
	Regenerative resistor power loss			Three-phase 200 V: 36 W DC 270 V: ―
	Control circuit power loss			19 W
	Total power loss			Three-phase 200 V: 245.6 W DC 270 V: 165.2 W
	Rated input current	Main circuit		Three-phase 200 V: 25 Arms DC 270 V: 34 Arms
		Control circuit		0.3 Arms
	Rush current	Main circuit		Three-phase 200 V: 68 A ^3 DC 270 V: 68 A ^3^*4 (External: 5 Ω)
		Control circuit		34 A ^*3
Performance specifications	Performance	Speed control range		1:5000 (Under conditions where load torque is equal to or less than rated torque)
		Speed fluctuation rate	At load fluctuation	0 to 100% load variation: ±0.01% or less (at rated rotation speed)
			At main circuit voltage change	Rated voltage ±10%: 0% (at rated rotation speed)
			At ambient temperature change	Ambient temperature 0 to +50°C 32 to 122°F: ±0.1% or less (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Velocity frequency response		3.1 kHz
	Dynamic brake			Operates at main circuit power off, servo alarm, servo off, limit switch detection (LSP/LSN), and forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: Disabled at 50 to 400 W Enabled at 750 W to 5.0 kW External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW^*5)
	Display Function	Panel function		7-segment LED Two rotary switches (16 ch)
		Communication status indicator LED		EtherCAT® communication: L/A × 2 EtherCAT® communication status: RUN×1 EtherCAT® error status: ERR×1
	Servo functions	Tuning		Auto-tuning, notch filter, vibration suppression, damping control, model tracking, friction compensation, load inertia moment ratio variation compensation, deviation reduction, low-frequency vibration suppression, etc.
		Monitor		Lifespan prediction, vibration, load factor, power consumption, temperature, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed inputs, 4 general-purpose inputs)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Max. OFF current/voltage		High-speed input: 0.1 mA, General-purpose input: 0.3 mA
		Common point mode		7 points/1 common (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.4 mA, General-purpose input: 4.5 mA
		Input impedance		Approx. 5.1 kΩ
		Assignable input signals		All signal assignment, Logic settable forced stop (FSTOP), Probe 1 latch input (PROBE1), Probe 2 latch input (PROBE2), Home switch input (HOME), Forward side limit switch (LSP), Reverse side limit switch (LSN), Forward side torque limit selection (PTL), Reverse side torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC/50 mA
		Leakage current when OFF		0.5 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Assignment of each signal except ALARM signal, Logic setting available alarm (ALARM), In-position (INPOS), Velocity matching (VCMP), Zero speed detection (ZSP), Ready to run (RDY), Torque limiting (TLM), Velocity limiting (VLM), Electromagnetic brake timing (BRAKE), Warning (WARN), Near positioning (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±12 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		A-phase (A+/A-), B-phase B (B+/B-), Z-phase (Z+/Z-): Differential line driver output
		Line driver		SN75ALS174 (T.I.) equivalent
		Output frequency		1.6 Mpps (at 2-phase quadruplication, equivalent to 6.4 MHz)^*6
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (Linearity effective range: ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	EtherCAT® communication	Applicable communication standards		IEC 61158 Type12, IEC 61800-7 CiA402 Drive Profile
		Physical layer		100 BASE-TX(IEEE802.3)
		Cable		Category 5 STP, 2 pair Automatic cable identification is performed by the AUTO MDI/MDI-X function.
		Mailbox		Emergency messages, SDO requests, SDO responses
		Distributed clocks		Free-run, DC mode (switchable), Supported DC cycles (62.5 μs to 4 ms, in 62.5 μs increments)
		Max. distance between stations		50 m 164.0'
	USB communication	Connected device		PC
		Communication standard		USB 2.0–compliant
		Function		Status display, Parameter settings, Tuning, etc.
^1 Single-phase input can only be used with the SV3-005L2, SV3-010L2, SV3-020L2, SV3-040L2, and SV3-075L2. ^2 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^3 The inrush current duration is 20 ms or less when used at the above current levels. ^4 When using the SV3-500L2 with DC power input, connect an external inrush current protection circuit and design it so that the circuit follows the power on/off sequence recommended by KEYENCE. Otherwise, the equipment may become damaged. Refer to the SV3 Series user’s manual for the power-on/off sequence. ^5 Depending on operating conditions, 2 kW, 3 kW, and 5 kW servo amplifiers can also be used. ^*6 The frequency divider ratio can be set as desired with a parameter.

Keyence SV3-B005AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-B005AK ^*1
General specifications	Applicable servo amplifier			SV3-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*2
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0537 ×10^-4 kg·m²
	Rated power rating			4.70 kW/s
	Rated angle acceleration			29,600 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.6 kg 21.16 oz
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.159 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence SV3-B005AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B005AS ^*1
General specifications	Applicable servo amplifier			SV3-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*2
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0537 ×10^-4 kg·m²
	Rated power rating			4.70 kW/s
	Rated angle acceleration			29,600 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.6 kg 21.16 oz
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.159 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence SV3-B010AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-B010AK ^*1
General specifications	Applicable servo amplifier			SV3-010L2
	Rated output			100 W
	Rated torque			0.318 N·m ^*2
	Instant maximum torque			1.11 N·m
	Rated current			0.85 Arms
	Instant maximum current			3.1 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.413 N·m/Arms
	Rotor moment of inertia			0.0785 ×10^-4 kg·m²
	Rated power rating			12.8 kW/s
	Rated angle acceleration			40,500 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.7 kg 24.69 oz
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.318 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence SV3-B010AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B010AS ^*1
General specifications	Applicable servo amplifier			SV3-010L2
	Rated output			100 W
	Rated torque			0.318 N·m ^*2
	Instant maximum torque			1.11 N·m
	Rated current			0.85 Arms
	Instant maximum current			3.1 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.413 N·m/Arms
	Rotor moment of inertia			0.0785 ×10^-4 kg·m²
	Rated power rating			12.8 kW/s
	Rated angle acceleration			40,500 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.7 kg 24.69 oz
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.318 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence SV3-B020AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-B020AK ^*1
General specifications	Applicable servo amplifier			SV3-020L2
	Rated output			200 W
	Rated torque			0.637 N·m ^*2
	Instant maximum torque			2.23 N·m
	Rated current			1.6 Arms
	Instant maximum current			5.8 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.444 N·m/Arms
	Rotor moment of inertia			0.327 ×10^-4 kg·m²
	Rated power rating			12.4 kW/s
	Rated angle acceleration			19,400 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			15×^*3
	Approx. weight			1.4 kg 3.09 lb
Electromagnetic brake specifications	Capacity			6 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.25 A
	Holding torque			0.637 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B020AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B020AS ^*1
General specifications	Applicable servo amplifier			SV3-020L2
	Rated output			200 W
	Rated torque			0.637 N·m ^*2
	Instant maximum torque			2.23 N·m
	Rated current			1.6 Arms
	Instant maximum current			5.8 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.444 N·m/Arms
	Rotor moment of inertia			0.327 ×10^-4 kg·m²
	Rated power rating			12.4 kW/s
	Rated angle acceleration			19,400 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			15×^*3
	Approx. weight			1.4 kg 3.09 lb
Electromagnetic brake specifications	Capacity			6 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.25 A
	Holding torque			0.637 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B040AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-B040AK ^*1
General specifications	Applicable servo amplifier			SV3-040L2
	Rated output			400 W
	Rated torque			1.27 N·m ^*2
	Instant maximum torque			4.46 N·m
	Rated current			2.5 Arms
	Instant maximum current			9.3 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.544 N·m/Arms
	Rotor moment of inertia			0.550 ×10^-4 kg·m²
	Rated power rating			29.3 kW/s
	Rated angle acceleration			23,000 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			10×^*3
	Approx. weight			1.7 kg 3.75 lb
Electromagnetic brake specifications	Capacity			6 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.25 A
	Holding torque			1.27 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B040AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B040AS ^*1
General specifications	Applicable servo amplifier			SV3-040L2
	Rated output			400 W
	Rated torque			1.27 N·m ^*2
	Instant maximum torque			4.46 N·m
	Rated current			2.5 Arms
	Instant maximum current			9.3 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.544 N·m/Arms
	Rotor moment of inertia			0.550 ×10^-4 kg·m²
	Rated power rating			29.3 kW/s
	Rated angle acceleration			23,000 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			10×^*3
	Approx. weight			1.7 kg 3.75 lb
Electromagnetic brake specifications	Capacity			6 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.25 A
	Holding torque			1.27 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B075AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-B075AK ^*1
General specifications	Applicable servo amplifier			SV3-075L2
	Rated output			750 W
	Rated torque			2.39 N·m ^*2
	Instant maximum torque			8.36 N·m
	Rated current			4.4 Arms
	Instant maximum current			16.9 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.584 N·m/Arms
	Rotor moment of inertia			1.76 ×10^-4 kg·m²
	Rated power rating			32.4 kW/s
	Rated angle acceleration			13,500 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			12×^*3
	Approx. weight			2.8 kg 6.17 lb
Electromagnetic brake specifications	Capacity			6.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.27 A
	Holding torque			2.39 N·m
	Release time			80 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B075AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B075AS ^*1
General specifications	Applicable servo amplifier			SV3-075L2
	Rated output			750 W
	Rated torque			2.39 N·m ^*2
	Instant maximum torque			8.36 N·m
	Rated current			4.4 Arms
	Instant maximum current			16.9 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.584 N·m/Arms
	Rotor moment of inertia			1.76 ×10^-4 kg·m²
	Rated power rating			32.4 kW/s
	Rated angle acceleration			13,500 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			12×^*3
	Approx. weight			2.8 kg 6.17 lb
Electromagnetic brake specifications	Capacity			6.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.27 A
	Holding torque			2.39 N·m
	Release time			80 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence SV3-B100AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B100AS ^*1
General specifications	Applicable servo amplifier			SV3-100L2
	Rated output			0.85k W
	Rated torque			5.39 N·m ^*2
	Instant maximum torque			14.2 N·m
	Rated current			6.9 Arms
	Instant maximum current			17 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.859 N·m/Arms
	Rotor moment of inertia			16.0 ×10^-4 kg·m²
	Rated power rating			18.2 kW/s
	Rated angle acceleration			3,370 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			5×^*3
	Approx. weight			7.5 kg 16.53 lb
Electromagnetic brake specifications	Capacity			10 W
	Rated voltage			24 VDC (−0%/+10%)
	Rated current (@20°C 68°F)			0.41 A
	Holding torque			12.7 N·m
	Release time			100 ms
	Operating time			80 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 3,000 min-1. At 4,000 min-1, 1 kW becomes 2×, 1.5 kW becomes 2×, 3 kW (with the SV3-300L2 connected) becomes 2.2×, 3 kW (with the SV3-500L2 connected) becomes 4×, and 5 kW becomes 2.4×.

Keyence SV3-B150AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B150AS ^*1
General specifications	Applicable servo amplifier			SV3-150L2
	Rated output			1.3k W
	Rated torque			8.34 N·m ^*2
	Instant maximum torque			23.3 N·m
	Rated current			10.7 Arms
	Instant maximum current			28 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.891 N·m/Arms
	Rotor moment of inertia			22.0 ×10^-4 kg·m²
	Rated power rating			31.6 kW/s
	Rated angle acceleration			3,790 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			5×^*3
	Approx. weight			9.0 kg 19.84 lb
Electromagnetic brake specifications	Capacity			10 W
	Rated voltage			24 VDC (−0%/+10%)
	Rated current (@20°C 68°F)			0.41 A
	Holding torque			19.6 N·m
	Release time			100 ms
	Operating time			80 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 3,000 min-1. At 4,000 min-1, 1 kW becomes 2×, 1.5 kW becomes 2×, 3 kW (with the SV3-300L2 connected) becomes 2.2×, 3 kW (with the SV3-500L2 connected) becomes 4×, and 5 kW becomes 2.4×.

Keyence SV3-B200AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B200AS ^*1
General specifications	Applicable servo amplifier			SV3-200L2
	Rated output			1.8k W
	Rated torque			11.5 N·m ^*2
	Instant maximum torque			28.7 N·m
	Rated current			16.7 Arms
	Instant maximum current			42 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.748 N·m/Arms
	Rotor moment of inertia			28.1 ×10^-4 kg·m²
	Rated power rating			47.1 kW/s
	Rated angle acceleration			4,090 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			5×
	Approx. weight			11.0 kg 24.25 lb
Electromagnetic brake specifications	Capacity			10 W
	Rated voltage			24 VDC (−0%/+10%)
	Rated current (@20°C 68°F)			0.41 A
	Holding torque			19.6 N·m
	Release time			100 ms
	Operating time			80 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence SV3-B300AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B300AS ^*1
General specifications	Applicable servo amplifier			SV3-300L2, SV3-500L2
	Rated output			SV3-300L2: 2.4k W SV3-500L2: 2.9k W
	Rated torque			SV3-300L2: 15.1 N·m SV3-500L2: 18.6 N·m ^*2
	Instant maximum torque			SV3-300L2: 45.1 N·m SV3-500L2: 54.0 N·m
	Rated current			SV3-300L2: 19.6 Arms SV3-500L2: 23.8 Arms
	Instant maximum current			SV3-300L2: 56 Arms SV3-500L2: 70 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.826 N·m/Arms
	Rotor moment of inertia			53.9 ×10^-4 kg·m²
	Rated power rating			SV3-300L2: 42.3 kW/s SV3-500L2: 64.2 kW/s
	Rated angle acceleration			SV3-300L2: 2,800 rad/s² SV3-500L2: 3,450 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			SV3-300L2: 3× SV3-500L2: 5× ^*3
	Approx. weight			19.5 kg 42.99 lb
Electromagnetic brake specifications	Capacity			18.5 W
	Rated voltage			24 VDC (−0%/+10%)
	Rated current (@20°C 68°F)			0.77 A
	Holding torque			43.1 N·m
	Release time			170 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 3,000 min-1. At 4,000 min-1, 1 kW becomes 2×, 1.5 kW becomes 2×, 3 kW (with the SV3-300L2 connected) becomes 2.2×, 3 kW (with the SV3-500L2 connected) becomes 4×, and 5 kW becomes 2.4×.

Keyence SV3-B500AS Keyence

$0.00

Sold Out

Specifications

Model				SV3-B500AS ^*1
General specifications	Applicable servo amplifier			SV3-500L2
	Rated output			4.4k W
	Rated torque			28.4 N·m ^*2
	Instant maximum torque			71.6 N·m
	Rated current			32.8 Arms
	Instant maximum current			84 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.932 N·m/Arms
	Rotor moment of inertia			75.4 ×10^-4 kg·m²
	Rated power rating			107 kW/s
	Rated angle acceleration			3,770 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			5×^*3
	Approx. weight			23.5 kg 51.81 lb
Electromagnetic brake specifications	Capacity			18.5 W
	Rated voltage			24 VDC (−0%/+10%)
	Rated current (@20°C 68°F)			0.77 A
	Holding torque			43.1 N·m
	Release time			170 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 3,000 min-1. At 4,000 min-1, 1 kW becomes 2×, 1.5 kW becomes 2×, 3 kW (with the SV3-300L2 connected) becomes 2.2×, 3 kW (with the SV3-500L2 connected) becomes 4×, and 5 kW becomes 2.4×.

Keyence SV3-M005AK Keyence

$0.00

Sold Out

Specifications

Model				SV3-M005AK
General specifications	Applicable servo amplifier			SV3-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*1
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0457 ×10^-4 kg·m²
	Rated power rating			5.53 kW/s
	Rated angle acceleration			34,700 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.3 kg 10.58 oz
^*1 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Previous Page 267 / 290Next