Remote I/O

Showing 1369 - 1374 of 1374 products

Pepperl+Fuchs VBA-2E-GH11-IU Pepperl+Fuchs

$0.00

Sold Out

Pepperl+Fuchs AS-Interface Component (P/N: VBA-2E-GH11-I/U). AS-Interface gateway, module, or power supply for distributed I/O with single flat-cable connectivity.

Pepperl+Fuchs KFA6-STR-1244 Pepperl+Fuchs

$668.32

Only 2 units left

Pepperl+Fuchs K-System Safety Barrier (P/N: KFA6-STR-1.24.4). Isolated safety barrier for analog/digital signals in hazardous areas with SIL certification.

Pepperl+Fuchs VBA-1E1A-G10-ZAL Pepperl+Fuchs

$187.50

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Pepperl+Fuchs VBA-4E4A-KE-ZE Pepperl+Fuchs

$275.96

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Pepperl+Fuchs VBA-4E3A-KE-ZEJQ Pepperl+Fuchs

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Pepperl+Fuchs KCD2-RR-EX1 Pepperl+Fuchs

$220.23

In stock, 11 units

Pepperl+Fuchs K-System Safety Barrier (P/N: KCD2-RR-EX1 |). Isolated safety barrier for analog/digital signals in hazardous areas with SIL certification.

Previous Page 58 / 58

Remote I/O systems are distributed field-interface hardware that connect a central PLC or DCS controller to sensors, actuators, and other field devices over an industrial network, eliminating long point-to-point cable runs from the control panel to the field. PLC Direct supplies remote I/O hardware as an independent supplier, carrying surplus sealed, refurbished, and used equipment for maintenance and replacement in installed distributed control architectures.

Where Are Remote I/O Used in Industrial Environments?

Remote I/O systems are used wherever field devices are physically distant from the central controller, and routing individual signal cables back to the control room is impractical, expensive, or unreliable over long distances. These systems place I/O hardware close to the field devices they interface with, reducing wiring costs and cabinet footprint while maintaining deterministic communication back to the controller over a single network cable or fiber run.

Facilities and operations that depend on remote I/O include:

Large-scale process plants and refineries where field instruments and actuators are distributed across multiple process units, each requiring local I/O nodes connected to a central DCS or PLC over PROFIBUS or EtherNet/IP.
Water and wastewater treatment facilities managing pump stations, lift stations, and remote treatment sites across distributed geographic locations with a single SCADA-connected controller architecture.
Automotive and discrete manufacturing plants positioning remote I/O drops at each workstation or machine cell along an assembly line to reduce inter-panel wiring.
Food and beverage processing facilities using distributed I/O nodes in washdown or sealed enclosures close to filling, conveyor, and packaging equipment.
Mining and materials-handling operations with conveyor systems, crusher stations, and transfer points spread across large sites requiring field-mounted I/O hardware rated for harsh environments.

Replacement remote I/O hardware, including drop adaptors, I/O modules, and communication interface units, is a routine maintenance requirement in aging distributed control installations.

Which Brands of Remote I/O Does PLC Direct Stock?

PLC Direct stocks remote I/O hardware across the major distributed I/O platforms deployed in installed automation systems worldwide.

Schneider Electric Modicon Momentum and Modicon X80: 170-series Modicon Momentum discrete and analog distributed I/O modules with communication adaptors for Interbus and other fieldbus protocols, alongside BMXCRA and BMECRA series Ethernet RIO drop adaptors for Modicon M340 and M580 X80 platforms, and 140CRA-series Ethernet RIO drop adaptors for Modicon Quantum systems.
Siemens SIMATIC ET 200SP: Distributed I/O station hardware including IM 155-6 PROFINET and PROFIBUS interface modules, digital and analog peripheral modules, and server modules for remote I/O station assembly in installed SIMATIC S7 and ET 200 architectures.
Beckhoff EtherCAT Box modules (EPxxxx series): IP67-rated distributed I/O modules for direct field mounting without a control cabinet, covering digital input, digital output, and analog signal types connected over EtherCAT for installed Beckhoff PC-based control systems.
ABB S500 distributed I/O: CI541-DP PROFIBUS and CI592-CS31 communication interface modules with DA501 and DA502 digital/analog I/O modules, supporting distributed field I/O in AC500-based control architectures across remote field cabinet installations.

PLC Direct carries remote I/O hardware as surplus sealed, refurbished, and used equipment, giving maintenance teams options across condition grades and budget requirements.

What Should You Know Before Ordering Remote I/O?

Hardware condition options: PLC Direct supplies remote I/O hardware in surplus sealed, refurbished, and used condition. Surplus sealed units are factory-sealed stock that has not been previously installed; refurbished hardware has been inspected and tested to confirm operational functionality; used equipment is sourced from decommissioned systems and suits facilities managing lifecycle replacements under budget constraints.

Compatibility and part identification: Remote I/O hardware is platform-specific and must match the controller's network protocol, the drop adaptor or interface module type, and the I/O module form factor for the installed station. Schneider Modicon Momentum, X80, and Quantum remote I/O components are not interchangeable across these three platforms despite sharing the Modicon brand. Confirm the platform name, drop adaptor part number, network protocol, and I/O module series from the installed system's network and hardware documentation before ordering.

Warranty: All remote I/O hardware purchased from PLC Direct carries a standard 1-year PLC Direct warranty covering defects and functionality, applicable to surplus sealed, refurbished, and used products.

PLC Direct supplies remote I/O hardware for replacement and maintenance purposes and does not provide system design, programming, or integration services.

Frequently Asked Questions

Remote I/O places signal interface hardware in field cabinets or enclosures close to the sensors and actuators it connects to, communicating back to the central controller over a single fieldbus or industrial Ethernet network rather than individual signal cables. Local I/O modules mount directly in the controller rack and communicate over the backplane; remote I/O is the preferred architecture wherever field devices are spread across distances that would make point-to-point wiring from a central panel impractical.

The most widely installed protocols in remote I/O architectures are PROFIBUS DP, PROFINET, EtherNet/IP, and EtherCAT, with legacy installations also using Modbus RTU, DeviceNet, and Interbus. The protocol used determines which drop adaptor or interface module is required at the remote station, and the controller must have a matching communication module or built-in port to support it. Siemens ET 200SP supports both PROFIBUS and PROFINET; Schneider Modicon X80 uses EtherNet/IP; Beckhoff EtherCAT Box modules require an EtherCAT master port on the controller.

A like-for-like replacement of the same part number at the same network address will typically restore operation without changes to the controller program, as the I/O data mapping is defined in the hardware configuration rather than the application logic. However, if the replacement hardware has a different firmware revision or hardware generation, the system's hardware configuration file may need to be updated before the controller recognizes the new module.

A remote I/O drop adaptor is the interface unit at a remote station that connects the fieldbus or Ethernet network to the local I/O modules in that cabinet, acting as the network node through which the controller communicates. If the drop adaptor fails, the entire remote station goes offline regardless of whether the I/O modules themselves are functional, making it one of the highest-priority replacement components in a distributed I/O architecture.

Start with the part number on the failed component's label, then cross-reference it against the installed system's hardware configuration file or network topology diagram to confirm the drop adaptor type, network protocol, and I/O module series in use at that station. For Schneider Modicon systems, the platform generation, Momentum, X80, or Quantum, determines which drop adaptor and module series apply, as these are not interchangeable across platforms.