Modules

634 products

Showing 577 - 600 of 634 products

Showing 577 - 600 of 634 products
View
ABE9C1280C23 Schneider
Schneider ABE9C1280C23 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Advantys ABE9
Product or Component Type IP67 passive splitter box
Number of channels 8
Electrical connection 1 male connector M23 19 pins
8 female connectors M12 5 pins
Status LED Without

Complementary

Characteristic Value(s)
Number of ways 16 ways
[Ue] rated operational voltage 24 V DC
Current per channel 4 A
Insulation group Category 3 VDE 0110
Operating position Any position
Fixing Mode M4 screw fixing
Contact resistance 5000 µOhm
Current of common 16 A 0.002 in² (1 mm²)
12 A 0.001 in² (0.75 mm²)
Separation of commons Without
Product Weight 0.31 lb(US) (0.14 kg)
ABE9C1280L10 Schneider
Schneider ABE9C1280L10 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Advantys ABE9
Product or Component Type IP67 passive splitter box
Number of channels 8
Electrical connection 1 pre-wired cable connector, 32.8 ft (10 m)
8 female connectors M12 5 pins
Status LED Without

Complementary

Characteristic Value(s)
Number of ways 16 ways
[Ue] rated operational voltage 24 V DC
Current per channel 4 A
Insulation group Category 3 VDE 0110
Operating position Any position
Fixing Mode M4 screw fixing
Contact resistance 5000 µOhm
Current of common 16 A 0.002 in² (1 mm²)
12 A 0.001 in² (0.75 mm²)
Separation of commons Without or with
Product Weight 6.75 lb(US) (3.06 kg)
ABE9C1280M Schneider
Schneider ABE9C1280M Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Advantys ABE9
Product or Component Type IP67 passive splitter box
Number of channels 8
Electrical connection 1 male plug-in connector
8 female connectors M12 5 pins
Status LED Without

Complementary

Characteristic Value(s)
Number of ways 16 ways
[Ue] rated operational voltage 24 V DC
Current per channel 4 A
Insulation group Category 3 VDE 0110
Operating position Any position
Fixing Mode M4 screw fixing
Contact resistance 5000 µOhm
Current of common 16 A 0.002 in² (1 mm²)
12 A 0.001 in² (0.75 mm²)
Separation of commons Without or with
Product Weight 0.2 lb(US) (0.1 kg)
ABE9C1281C23 Schneider
Schneider ABE9C1281C23 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Advantys ABE9
Product or Component Type IP67 passive splitter box
Number of channels 8
Electrical connection 1 male connector M23 19 pins
8 female connectors M12 5 pins
Status LED 1 LED (Green) power ON
1 LED per channel (Yellow) channel status

Complementary

Characteristic Value(s)
Number of ways 16 ways
[Ue] rated operational voltage 24 V DC
Current per channel 4 A
Insulation group Category 3 VDE 0110
Operating position Any position
Fixing Mode M4 screw fixing
Contact resistance 5000 µOhm
Current of common 16 A 0.002 in² (1 mm²)
12 A 0.001 in² (0.75 mm²)
Separation of commons Without
Product Weight 0.31 lb(US) (0.14 kg)
ABE7S16S2B0 Schneider
Schneider ABE7S16S2B0 Schneider
$1,074.68
Only 4 units left

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Solid state output relay sub-base
[Us] rated supply voltage 24 V DC PLC end
24 V DC preactuator end
Number of channels 16
Number of terminal per channel 2
Relay Type Soldered solid state relay

Complementary

Characteristic Value(s)
Terminal block type Removable
Isolation PLC/operative part No
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Current state 0 guaranteed 0.4 mA PLC end)
Voltage state 0 guaranteed 3.4 V PLC end
Current state 1 guaranteed 3.1 mA PLC end)
Voltage state 1 guaranteed 16.9 V PLC end
Maximum current per output common 8 A
Current per channel 0.5 A preactuator end
Minimum switching current 1 mA
Drop-out voltage 0.6 V preactuator end)
Maximum switching current 500 mA DC-12
500 mA DC-13
Maximum tungsten load <10 W DC-6
Maximum residual current 0.3 mA preactuator end
Fault type Overload
Short-circuit
Fault indication Yes
Switchable inductive energy L/R <= 400(U.I) ms
Maximum circuit breaker threshold 0.75 A
Response time <= 0.02 ms from state 1 to 0
<= 0.1 ms from state 0 to 1
Switching frequency < 0.6/LI² Hz
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Width 8.1 in (206 mm)
Product Weight 0.893 lb(US) (0.405 kg)
ABE7P16T334_Schneider
Schneider ABE7P16T334 Schneider
$928.88
Only 1 unit left

ABE7P16T334 SCHNEIDER ELECTRIC.
ABE9C1240M Schneider
Schneider ABE9C1240M Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Advantys ABE9
Product or Component Type IP67 passive splitter box
Number of channels 4
Electrical connection 1 male plug-in connector
4 female connectors M12 5 pins
Status LED Without

Complementary

Characteristic Value(s)
Number of ways 8 ways
[Ue] rated operational voltage 24 V DC
Current per channel 4 A
Insulation group Category 3 VDE 0110
Operating position Any position
Fixing Mode M4 screw fixing
Contact resistance 5000 µOhm
Current of common 16 A 0.002 in² (1 mm²)
12 A 0.001 in² (0.75 mm²)
Separation of commons Without or with
Product Weight 0.13 lb(US) (0.06 kg)
ABE7R16T212 Schneider
Schneider ABE7R16T212 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Sub-base with plug-in electromechanical relay
Sub-base type Output sub-base
[Us] rated supply voltage 19...30 V IEC 61131-2
Number of channels 16

Complementary

Characteristic Value(s)
supply voltage type DC
Product Compatibility ABR7S21
Contacts type and composition 1 NO
Status LED 1 LED per channel (Green) channel status
1 LED (Green) power ON
Polarity distribution Polarity distribution contact common per 2 groups of 8 channels
Short-circuit protection 1 A internal fuse, 5 x 20 mm, fast blow PLC end)
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1 A
Voltage drop on power supply fuse 0.3 V
[Ui] rated insulation voltage 2000 V terminals/mounting rails
300 V coil circuit/contact circuits IEC 60947-1
[Uimp] rated impulse withstand voltage 2.5 kV
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Product Weight 1.61 lb(US) (0.73 kg)
ABE7H34E200_Schneider
Schneider ABE7H34E200 Schneider
$0.00
Sold Out

"This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system." "This is a kit containing two sub-bases and a 2meter long Y-cordset." "Sub-bases provide 2x16 modularity input/output channels with 1 terminal per channel. Y-cordset is equipped with 1x 40-way FCN, and 2x HE10 20-way connectors." "This product is designed to simplify I/O connection to a PLC within a control panel, and connects to channels with HE 10 and SUB-D connectors." "It is a sub base with a maximum supply current of 1.8A and a rated supply voltage of 19V to 30V" "It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product." "This kit weighs 0.725kg." "It is suitable for all types of industrial applications managed with Modicon X80 I/O modules or Modicon M340 controllers." "This kit is certified by GL, CSA, DNV, BV, LROS, UL, GL and EAC." "This kit is compatible with Modicon X80 I/O modules or Modicon M340 controllers." "The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit)." "Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment." "Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors."

Main

Characteristic Value(s)
Range of product Modicon ABE7
Product or component type Passive discrete I/O sub-base
Sub-base type Low cost sub-base
[Us] rated supply voltage 19...30 V conforming to IEC 61131-2
Number of channels 16
Number of terminal per channel 1
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² (AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² (AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² (AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² (AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² (AWG 24...AWG 14) solid

Complementary

Characteristic Value(s)
supply voltage type DC
Number of horizontal rows 2
Product compatibility Modicon Premium PLC
Modicon TSX Micro PLC
Status LED 1 LED per channel (green) channel status
1 LED (green) power ON
Short-circuit protection 2 A internal fuse, 5 x 20 mm, fast blow (PLC end)
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1.8 A
Current per channel 0.5 A
Maximum current per output common 1.8 A
Voltage drop on power supply fuse 0.3 V
[Ui] rated insulation voltage 2000 V terminals/mounting rails
Installation category II conforming to IEC 60664-1
Tightening torque 0.6 N.m with flat Ø 3.5 mm screwdriver
Product weight 0.41 kg
ABE7S16E2B1 Schneider
Schneider ABE7S16E2B1 Schneider
$1,474.26
Only 2 units left

This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system. The sub-base with soldered solid state output relay, provides 16 channels. It has 2 terminals per channel. This product enables rapid connection of I/O modules. It is a relay sub base with a supply voltage of 19V to 30V DC and a current of 0.012A per channel. It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product. It weighs 0.37kg. It is suitable for all types of industrial applications. This product is certified by GL, CSA, DNV, BV, LROS and UL. The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit). Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment. Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors.

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Solid state input relay sub-base
[Us] rated supply voltage 24 V DC PLC end)
24 V DC sensor end)
Number of channels 16
Number of terminal per channel 2
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm², 0.0001…0.002 in² (0.09…1.5 mm²) AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm², 0.0002…0.004 in² (0.14…2.5 mm²) AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm², 0.0002…0.004 in² (0.14…2.5 mm²) AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm², 0.0001…0.001 in² (0.09…0.75 mm²) AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm², 0.0003…0.004 in² (0.2…2.5 mm²) AWG 24...AWG 14) solid

Complementary

Characteristic Value(s)
Terminal block type Removable
Supply voltage limits 19…30 V DC PLC end)IEC 61131-2
Isolation PLC/operative part Yes
Protection type Internal fuse 1 A 5 x 20 mm fast blow PLC end
Adjustable by external fuse fast blow sensor end
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Current per channel 0.012 A
Current state 1 guaranteed >= 2 mA sensor end)
Voltage state 1 guaranteed >= 15 V sensor end
Maximum switching current 15 mA PLC end)
Minimum switching current 1 mA for PLC end
Response time <= 0.05 ms from state 0 to 1
<= 0.4 ms from state 1 to 0
Switching frequency <= 1000 Hz 50 %
[Uimp] rated impulse withstand voltage 2.5 kV IEC 60947-1
[Ui] Rated Insulation Voltage 2000 V
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Product Weight 0.82 lb(US) (0.37 kg)
ABE7H20E100 Schneider
Schneider ABE7H20E100 Schneider
$0.00
Sold Out

passive connection sub-base ABE7 - 16 inputs or outputs - Micro/Premium cable 1m
ABE7R08S210 Schneider
Schneider ABE7R08S210 Schneider
$1,055.85
Only 1 unit left

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Electromechanical output relay sub-base
[Us] rated supply voltage 24 V DC PLC end
Number of channels 8
Number of terminal per channel 2

Complementary

Characteristic Value(s)
Terminal block type Removable
Polarity distribution Volt-free
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum current per output common 10 A
Current per channel 5 A preactuator end
Minimum switching current 10 mA >= 5 V
Drop-out voltage 2.4 V 68 °F (20 °C) PLC end)
Switching frequency <= 0.5 Hz
<= 10 Hz
Threshold tripping voltage 19.7 V 104 °F (40 °C)
Drop-out current 1 mA 68 °F (20 °C)
Maximum power dissipation per channel in W 0.36 W PLC end)
Contacts type and composition 1 NO preactuator end
Maximum switching voltage 250 V AC 50/60 Hz IEC 60947-5-1
30 V DC IEC 60947-5-1
Electrical durability 500000 cycles 600 mA 24 V DC-13 10 ms preactuator end)
500000 cycles 1500 mA 230 V AC-12 preactuator end)
500000 cycles 1500 mA 24 V DC-12 preactuator end)
500000 cycles 900 mA 230 V AC-15 preactuator end)
Electrical reliability 1e-008
Operating time <= 10 ms coil energisation and NO closing
<= 5 ms coil de-energisation and NO opening
Contact bounce time <= 5 ms 1 NO
Operating rate in Hz 10 Hz no load
0.5 Hz at Ie
Mechanical durability 20000000 cycles
[Uimp] rated impulse withstand voltage 2.5 kV IEC 60947-1
[Ui] Rated Insulation Voltage 2000 V
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Width 4.9 in (125 mm)
Product Weight 0.988 lb(US) (0.448 kg)
ABE7S16S1B2 Schneider
Schneider ABE7S16S1B2 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Solid state output relay sub-base
[Us] rated supply voltage 24 V DC PLC end
24 V DC preactuator end
Number of channels 16
Relay Type Soldered solid state relay

Complementary

Characteristic Value(s)
Terminal block type Removable
Isolation PLC/operative part No
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Current state 0 guaranteed 0.4 mA PLC end)
Voltage state 0 guaranteed 3.4 V PLC end
Current state 1 guaranteed 3.1 mA PLC end)
Voltage state 1 guaranteed 16.9 V PLC end
Maximum current per output common 9 A
Current per channel 0.5 A preactuator end
Minimum switching current 1 mA
Drop-out voltage 0.3 V preactuator end)
Maximum switching current 700 mA DC-12
700 mA DC-13
Maximum tungsten load <10 W DC-6
Maximum residual current 0.5 mA preactuator end
Fault type Short-circuit
Overload
Fault indication Without
Switchable inductive energy L/R <= 400(U.I) ms
Maximum circuit breaker threshold 0.75 A
Response time <= 0.1 ms from state 1 to 0
<= 0.2 ms from state 0 to 1
Switching frequency < 0.6/LI² Hz
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Width 4.9 in (125 mm)
Product Weight 0.9 lb(US) (0.4 kg)
ABE7ACC10 Schneider
Schneider ABE7ACC10 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Accessory / separate part designation Redundant output sub-base
Accessory / separate part destination PLC
Accessory / separate part category Connection accessories
Accessory / Separate Part Type Splitter sub-base
Range of Product Modicon ABE7
Sub-base type Redundant output sub-base
Number of channels 16
Quantity per Set Set of 1

Complementary

Characteristic Value(s)
Channel splitting 2 x 16
Product Weight 0.165 lb(US) (0.075 kg)
ABE7H34E100_Schneider
Schneider ABE7H34E100 Schneider
$0.00
Sold Out

"This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system." "This is a kit containing two sub-bases and a 1meter long Y-cordset." "Sub-bases provide 2x16 modularity input/output channels with 1 terminal per channel. Y-cordset is equipped with 1x 40-way FCN, and 2x HE10 20-way connectors." "This product is designed to simplify I/O connection to a PLC within a control panel, and connects to channels with HE 10 and SUB-D connectors." "It is a sub base with a maximum supply current of 1.8A with 0.5A per channel, and a rated supply voltage of 19V to 30V." "It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product." "This kit weighs 0.582kg." "It is suitable for all types of industrial applications managed with Modicon X80 I/O modules or Modicon M340 controllers." "This kit is certified by GL, CSA, DNV, BV, LROS, UL, GL and EAC." "This kit is compatible with Modicon X80 I/O modules or Modicon M340 controllers." "The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit)." "Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment." "Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors."

Main

Characteristic Value(s)
Range of product Modicon ABE7
Product or component type Passive discrete I/O sub-base
Sub-base type Low cost sub-base
[Us] rated supply voltage 19...30 V conforming to IEC 61131-2
Number of channels 16
Number of terminal per channel 1
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² (AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² (AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² (AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² (AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² (AWG 24...AWG 14) solid

Complementary

Characteristic Value(s)
supply voltage type DC
Number of horizontal rows 2
Product compatibility Modicon TSX Micro PLC
Modicon Premium PLC
Status LED 1 LED (green) power ON
1 LED (amber) APP1
Short-circuit protection 2 A internal fuse, 5 x 20 mm, fast blow (PLC end)
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1.8 A
Current per channel 0.5 A
Maximum current per output common 1.8 A
Voltage drop on power supply fuse 0.3 V
[Ui] rated insulation voltage 2000 V terminals/mounting rails
Installation category II conforming to IEC 60664-1
Tightening torque 0.6 N.m with flat Ø 3.5 mm screwdriver
Product weight 0.33 kg
ABE7P16T111 Schneider
Schneider ABE7P16T111 Schneider
$0.00
Sold Out

sub-base for plug-in relay ABE7 - 16 channels - relay 5 mm
ABE7P16T214 Schneider
Schneider ABE7P16T214 Schneider
$0.00
Sold Out

This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system. This sub-base for plug-in relay, provides 16 channels. It has 1 switch disconnector per channel. This product enables rapid connection of I/O modules. It is a relay sub base with a supply voltage of 19V to 30V DC and a maximum supply current of 1A. It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product. It weighs 0.675kg. It is suitable for all types of industrial applications. This product is certified by GL, CSA, DNV, BV, LROS and UL. This sub-base is suitable for use with ABR7S2, ABS7SA2, ABS7SC2 and ABE7ACC20 connection sub-base accessory. The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit). Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment. Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors.

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Sub-base for plug-in relay
Sub-base type Output sub-base
[Us] rated supply voltage 19...30 V IEC 61131-2
Number of channels 16
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 24...AWG 14) solid
Channel additional information 1 switch disconnector per channel

Complementary

Characteristic Value(s)
supply voltage type DC
Product Compatibility ABR7S2.
ABS7SA2.
ABS7SC2.
ABE7ACC20
Status LED 1 LED per channel (Green) channel status
1 LED (Green) power ON
Polarity distribution Volt-free
Short-circuit protection 1 A internal fuse, 5 x 20 mm, fast blow PLC end)
0.5 A fuse per channel, 5 x 20 mm, fast blow output circuit)
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1 A
Voltage drop on power supply fuse 0.3 V
Maximum current per output common 16 A
[Ui] rated insulation voltage 300 V coil circuit/contact circuits IEC 60947-1
2000 V terminals/mounting rails
[Uimp] rated impulse withstand voltage 2.5 kV
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Product Weight 1.488 lb(US) (0.675 kg)
ABE7P16F310 Schneider
Schneider ABE7P16F310 Schneider
$937.50
Only 3 units left

sub-base for plug-in relay ABE7 - 16 channels - relay 12.5 mm
ABE7H16C11 Schneider
Schneider ABE7H16C11 Schneider
$0.00
Sold Out

passive connection sub-base ABE7 - 16 inputs or outputs - Led
ABE7H16C31 Schneider
Schneider ABE7H16C31 Schneider
$0.00
Sold Out

passive connection sub-base ABE7 - 16 inputs or outputs - Led
ABE7H16S43 Schneider
Schneider ABE7H16S43 Schneider
$487.50
Only 1 unit left

This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system. This passive discrete I/O sub-base offers 1 switch disconnector per channel. It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product. The width of this product is 206mm. It weighs 0.64kg. It is suitable for all types of industrial applications. This product is certified by GL, CSA, DNV, BV, LROS, UL, GL and EAC. The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit). Modicon ABE7 means greater simplicity to rationalize wiring in your automation system equipment. Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors.

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Passive discrete I/O sub-base
Sub-base type Input sub-base
[Us] rated supply voltage 19...30 V IEC 61131-2
Number of channels 16
Number of terminal per channel 2
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 24...AWG 14) solid
Channel additional information 1 switch disconnector per channel

Complementary

Characteristic Value(s)
supply voltage type DC
Number of horizontal rows 1
Status LED 1 LED per channel (Green) channel status
1 LED per channel (Red) blown fuse indication
1 LED (Green) power ON
Polarity distribution 24 V
Short-circuit protection 1 A internal fuse, 5 x 20 mm, fast blow PLC end)
0.125 A fuse per channel, 5 x 20 mm, fast blow output circuit)
Connector Type HE-10
Pin number 20 pins
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1.8 A
Current per channel 0.125 A
Maximum current per output common 1.8 A
Voltage drop on power supply fuse 0.3 V
Maximum voltage drop per channel 0.1 V
[Ui] Rated Insulation Voltage 2000 V
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Width 8.1 in (206 mm)
Height 3.03 in (77 mm)
Depth 2.3 in (58 mm)
Product Weight 1.41 lb(US) (0.64 kg)
ABE7H20E200 Schneider
Schneider ABE7H20E200 Schneider
$0.00
Sold Out

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Passive discrete I/O sub-base
Sub-base type Low cost sub-base
[Us] rated supply voltage 19...30 V IEC 61131-2
Number of channels 16
Number of terminal per channel 1
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 24...AWG 14) solid

Complementary

Characteristic Value(s)
supply voltage type DC
Number of horizontal rows 2
Product Compatibility Modicon Premium PLC
Modicon TSX Micro PLC
Status LED 1 LED per channel (Green) channel status
1 LED (Green) power ON
Short-circuit protection 2 A internal fuse, 5 x 20 mm, fast blow PLC end)
Fixing mode By clips (35 mm symmetrical DIN rail)
By screws (solid plate with fixing kit)
Maximum supply current 1.8 A
Current per channel 0.5 A
Maximum current per output common 1.8 A
Voltage drop on power supply fuse 0.3 V
[Ui] rated insulation voltage 2000 V terminals/mounting rails
Installation category II IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Product Weight 0.90 lb(US) (0.41 kg)
170AMM09000 Schneider
Schneider 170AMM09000 Schneider
$1,637.79
In stock, 13 units

distributed analog/discrete I/O Modicon Momentum
ABE7E16EPN20 Schneider
Schneider ABE7E16EPN20 Schneider
$727.50
Only 1 unit left

Main

Characteristic Value(s)
Range of Product Modicon ABE7
Product or Component Type Passive discrete I/O sub-base
[Us] rated supply voltage 24 V DC controller side
24 V DC sensor/controller side
Number of channels 16
Number of terminal per channel 2
Connections - terminals Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid
Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end
Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end
Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 28...AWG 16) solid
Connector destination Twido programmable controller

Complementary

Characteristic Value(s)
Supply voltage limits 19…30 V DC controller side)IEC 61131-2
20.4…26.4 V DC sensor/controller side)IEC 61131-2
Discrete input number 16
Discrete input logic Sink
Discrete output voltage 24 V
Discrete output voltage type DC
Product Compatibility TWDDDI16DK
TWDDDI32DK
Status LED 1 LED power ON
Polarity distribution 1 common/16 channels input
Short-circuit protection 2 A internal fuse, 5 x 20 mm, fast blow controller side)
Connector Type HE-10
Pin number 20 pins
Fixing mode By clips 35 mm symmetrical DIN rail IEC 60715
By screws
Maximum supply current 2 A
Switched current 15 mA input circuit
Voltage drop on power supply fuse 0.3 V
[Ui] rated insulation voltage 2000 V terminals/mounting rails
Overvoltage category II conforming to IEC 60664-1
Tightening torque 5.3 lbf.in (0.6 N.m) flat Ø 3.5 mm
Product Weight 0.95 lb(US) (0.43 kg)

Recently viewed