Machine Vision Systems

$427.26

Only 3 units left

Specifications

Model			KV-NC8ER
Expansion output unit	External connectionmethod		Relay
	External connection method		European terminal block
	Rated load		250 VAC/30 VDC, 2 A
	Leakage current (when output is OFF)		−
	Residual voltage (at ON)
	ON resistance		50 mΩ or less
	Common method		4 points/1 common (4 terminals) ^*1
	Response time	OFF to ON	10 ms or less
		ON to OFF
	Relay life		Electrical: 100000 cycles or more (20 cycles/minute) Mechanical: 20000000 cycles or more
	Relay replacement		Impossible
Internal current consumption			70 mA or less
Weight			Approx. 130 g
^*1 The KV-NC8ER has four terminals for each of C0 and C1 respectively, which are shorted internally. (C0 and C1 are independent.)

Keyence OP-87225 Keyence

$178.62

In stock, 11 units

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87685 Keyence

$228.27

Only 6 units left

Specifications

Model				OP-87685
Overview				The bracket for IV series.You can attach IV to Φ12mm pipe by using it.
Applicable product				IV series
Weight				Approx. 150 g

Keyence GC-1000R Keyence

$1,170.25

In stock, 17 units

Specifications

Model		GC-1000R
Input/output points	Safety inputs	14
	Safety outputs	4
	Safety relay output	1 (3a)
	AUX outputs	4
	Test outputs
Maximum number of connectable expansion units		-
Maximum number of connectable remote I/O modules
GC-Link ports		2 ports
Safety input specifications	Input device	Contact output device or PNP output device
	Input type	Type3
	ON level (voltage/current)	Min. 11 V/2 mA
	OFF level (voltage/current)	Max. 5 V/1.5 mA
	Short-circuit current	Si 0 to 3: Approx. 5 mA Si 4 to 13: Approx. 3 mA
	Protection circuit	Surge protection circuit, wrong wiring protection circuit
	Maximum cable length	Max. 100 m 328.1'
Safety output specifications	Output type	PNP transistor output (DC-13, Type 0.5, Protected outputs)^*1
	Maximum load current	500 mA
	Residual voltage (during ON)	Max. 2.0 V
	Leakage current (during OFF)	Max. 0.5mA
	Maximum capacitive load	0.5 µF
	Load wiring resistance	Max. 2.5Ω
	Protection circuit	Overcurrent protection circuit, reverse connection protection circuit
	Maximum cable length	Max. 30 m 98.4'
Safety relay output specifications	Output type	Relay (3a) (Externally-protected outputs)^*2
	Rated load (resistance load)	250 VAC 6A / 30 VDC 6A^*3
	Rated load (inductive load)	240 VAC 2A (AC-15) / 24 VDC 1A (DC-13)
	Relay output mechanical life	Resistance load (250 VAC 6A/30 VDC 6A): Min. 100,000 times Resistance load (250 VAC 1A/30 VDC 1 A): Min. 500,000 times Inductive load (AC-15: 240 VAC 2 A): Min. 100,000 times (cosø = 0.3) Inductive load (DC-13: 24 VDC 1 A): Min. 100,000 times (L/R = 48 ms)
	Maximum cable length	Max. 100 m 328.1'
	B10d	With rated load: 400,000 times With low load: 2,000,000 times
Test output specifications	Output type	PNP transistor output^*4
	Maximum load current	100 mA
	Protection circuit	Overcurrent protection circuit, reverse connection protection circuit
	Maximum cable length	Max. 100 m 328.1'^*5
AUX output specifications	Output type	Transistor output (PNP/NPN selectable by wiring) PNP output (DC-13, Type 0.1, Protected outputs)^1^4
	Maximum load current	PNP: 100 mA, NPN: 20 mA
	Residual voltage (during ON)	Max. 2.0 V
	Leakage current (during OFF)	Max. 0.5 mA
	Protection circuit	Overcurrent protection circuit, reverse connection protection circuit
	Maximum cable length	Max. 30 m 98.4'
Communication interface	USB	USB2.0
	Ethernet	-
Network functionality
Others	LCD display	1.77-inch color LCD
	Display buttons	4 points (3 operation keys + 1 BACK key)
Applicable standards	EMC	EMS: IEC 61131-2/-6, EN61131-2/-6 EMI: IEC 61131-2, FCC Part15B Class A, ICES-003, Class A
	Safety	IEC 61508, EN 61508 SIL3 IEC62061 SIL CL3 ISO/EN13849-1:2015 Cat. 4, PL e, UL1998
Dimensions		85×95×90 mm 3.35"×3.74"×3.54" (W×D×H)
Power supply	Power voltage	24 VDC (-20 to +20%) Class 2
	Power consumption	Max. 200 mA
Environmental resistance	Ambient temperature	−10 to +55 °C 14 to 131 °F (No freezing)
	Relative humidity	5 to 85% (No condensation)
	Storage temperature	−25 to +70 °C -13 to 158 °F (No freezing)
	Operating altitude	Max. 2000 m 6561.7'
	Overvoltage category	II III (relay output part of GC-1000R and GC-S1R)
	Pollution degree	2
	Vibration resistance	Frequency: 5 to 9 Hz, Half amplitude: 3.5 mm 0.14" Frequency: 9 to 150 Hz, Acceleration: 10 m/s² 10 times each in X, Y, Z directions
	Shock resistance	Acceleration: 150 m/s², Operating time: 11 ms, 3 times each in X, Y, Z directions
Material		Polycarbonate
Weight		Approx. 360 g
^1 Paragraph 6.4.6 Temporary overload of IEC 61131-2 supports up to 1.2 times the maximum load current. ^2 To comply with the requirements of IEC61131-2, connect 10 A fast blow fuse (IEC 60217) in series to each contact. ^3 Check the derating characteristics described later. ^4 AUX outputs (NPN output) and test outputs do not comply with paragraph 6.4.6 of IEC 61131-2. ^*5 When the test output is branched and connected to multiple safety input devices, the total branched cable length must not exceed 400 m 1312.3'.

Keyence OP-87527 Keyence

$191.84

Only 8 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GL-R52H Keyence

$1,142.64

Only 9 units left

Specifications

Model			GL-R52H
Detection capability			ø0.98" ø25 mm
Total length			40.94" 1040mm
No. of beam			52
Detection height			40.16" 1020mm
Protection height			41.93" 1065mm
Beam axis spacing/Lens diameter			20 mm / ø5 0.79" / ø0.20"
Detecting distance			0.66 to 49.21' 0.2 to 15 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	10
		OFF→ON	53.9^*2
		All blocked→ON	77^*3
	Optical synchronization system (Channel A or B)	ON→OFF	14.3
		OFF→ON	60.3^*2
		All blocked→ON	94.2^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	69
		Receiver	80
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		1440 g
	Receiver		1450 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence EX-110V Keyence

$228.35

In stock, 44 units

Specifications

Model		EX-110V^*1
Type		Sensor head
Amplifier unit		NPN: EX-V02 PNP: EX-V02P
Shape		M10 x 18 mm 0.71" Threaded
Measuring range		0 to 2 mm 0 to 0.08"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		NPN open-collector or non-voltage contact (Timing input, Reset input, Auto-zero input, Comparator output disable input, Synchronous input, External setting input)/PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.) PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	-10 to +60 °C 14 to 140 °F, No freezing
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 55 g (including 3 m 9.8' cable)
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence IV-H500MA Keyence

$908.91

In stock, 11 units

Specifications

Model		IV-H500MA
Type		Standard distance
Installed distance		50 to 500 mm 1.97" to 19.69"
View		Installed distance 50 mm 1.97": 25 (H) × 18 (V) mm 0.98" (H) × 0.71" (V) to installed distance 500 mm 19.69": 210 (H) × 157 (V) mm 8.27" (H) × 6.18" (V)
Image sensor	Type	1/3 inch monochrome CMOS
	Pixel	752 (H) x 480 (V) 29.61" (H) x 18.90" (V)
Focus adjustment		Auto^*1
Exposure time		1/10 to 1/25,000
Lights	Illumination	Red LED
	Lighting method	Pulse lighting/DC lighting is switchable
Tools	Type	Shape Detection, Color Area^2, Area^3, Edge Pixels, Width/Height, Diameter, Edge Presence, Pitch, Position Adjustment, High Speed Position Adjustment (1-Axis/2-Axis Adjustment)
	Number	Detection tools: 16 tools, position adjustment tool: 1 tool^*4
Switch settings (programs)		32 programs
Image history	Numbers	300 images^5^6
	Condition	NG only/All is selectable^*6
Analysis information		OFF/Statistics/Histograms/Matching rate list is switchable Statistics: Processing time (latest value, MAX, MIN, AVE), number of OKs, number of NGs, trigger numbers, trigger errors, judgment results list by tools Histograms: Histogram, matching degree (latest value, MAX, MIN, AVE), numbers of OKs, numbers of NGs Matching rate list: Judgment results list by tools, matching rate list by tools, judgment bar list by tools^*7
Other functions		HDR, HighGain, Color filters^2, Digital zoom^8, Brightness correction, Tilt correction, White balance^2, Mask function, Color histogram, Test run, ToolAutoTune, Input monitor, Output test, Security settings, Simulator^9, Sensor date/time information addition, Scaling function, Failing sensor list, Failure hold
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT
Input	Type	Non-voltage input/voltage input is switchable For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Inputs	6 inputs (IN1 to IN6)
	Function	IN1: External trigger, IN2 to IN6: Enable by assigning the optional functions Assignable functions: Program switching, Clear error, External master image registration
Output	Type	Open collector output NPN/PNP is switchable, N.O./N.C. is switchable For open collector NPN output: Maximum rating 26.4 V 50 mA, remaining voltage 1.5 V or lower For open collector PNP output: Maximum rating 26.4 V 50 mA, remaining voltage 2 V or lower
	Outputs	4 outputs (OUT1 to OUT4)
	Function	Enable by assigning the optional functions Assignable functions: Total judge result, RUN, BUSY, Error, Position adjustment result, Judge result of each tool, Result of the logical operation of each tool
Ethernet	Standard	100BASE-TX/10BASE-T^*10
	Connector	M12 4pin connector^*10
Network function		FTP client, EtherNet/IP™, PROFINET
Rating	Power voltage	24 VDC ±10 % (including ripple)
	Current consumption	0.6 A or less
Environmental resistance	Enclosure rating	IP67^*11
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions^*12
	Shock resistance	500 m/s², 3 times in each of 6 directions^*12
Material		Main unit case: Aluminium die-casting, Packing: NBR, Front cover: Acrylic, Mounting adapter: POM
Weight		Approx. 270 g
^1 The focusing position can be automatically adjusted at the time of installation. Deactivated during the operation. Focusing position can be registered by program. ^2 Color type only ^3 Possible with both the Color type and monochrome type ^4 Tools can be installed by programs. ^5 When using the FTP client function: 210 pictures ^6 Saves to the memory in the sensor. The images saved in the sensor can be backed up to the USB memory installed to the intelligent monitor (IV-M30) or to the PC by the software for IV (IV-H1). ^7 This can be displayed on the intelligent monitor (IV-M30) or by software for IV (IV-H1). ^8 Possible with both the color type and monochrome type ^9 Simulator can be used with the IV software (IV-H1). ^10 This is for connection with the intelligent monitor (IV-M30) or software for IV (IV-H1). ^11 Except when polarized filter attachment (OP-87436/OP-87437) is mounted ^12 Except when IV-G dome attachment (IV-D10) is mounted

Keyence OP-77679 Keyence

$130.04

Only 8 units left

Specifications

Model				OP-77679
Applicable product				GT Series/GT2 Series
Note				This is a flat-plate-type contact (sold separately). This contact can be used to perform detections using the peaks of the bumps of the target.

Keyence OP-87443 Keyence

$112.76

Only 9 units left

Specifications

Model				OP-87443
Type				Monitor power cable
Cable end				M8 4-pin / Strand wire
Length				2 m 6.6'

Keyence OP-87450 Keyence

$487.34

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence IV2-G30F Keyence

$1,181.79

In stock, 15 units

Specifications

Model		IV2-G30F
Type		Learning/standard type
Tools	Available modes	Learning mode / Standard mode
	Standard mode built-in tools	Outline, Color area^1, Area^2, Edge pixels, Color average^1, Brightness average^2, Width, Diameter, Edge presence, Pitch, OCR, Color/brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge)
	Number of tools	Detection tools: 16 tools, position adjustment tool: 1 tool^*3
Switch settings (programs)		128 programs (when using SD card) / 32 programs (when not using SD card)
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT, SD
Image history	Number of storable images	1000 images ^*4
	Save conditions	Selectable between NG only, NG and OK near threshold^5, and All ^4
Image data transfer	Transfer destination	Selectable between SD card and FTP server
	Transfer format	Selectable between bmp, jpeg, iv2p, and txt
	Transfer conditions	Selectable between NG only, NG and OK near threshold^*5, and All
Analysis information	RUN display	Tools list (Judgment results, degree of similarity, or degree of similarity bar display) ^*6
	RUN information	Switchable between OFF, histogram, processing time, count, and output monitor Histograms: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGs Processing time: Processing time (latest, Max., Min., Ave.), Image capture interval (latest, Max., Min., Ave.) Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errors, Strobe errors Output monitor: ON/OFF status by output
Other functions	Image capture function	Image buffer, Image capture range, Digital zoom (2×, 4×), HDR, High gain, Color filter^1, White balance^1, Brightness correction
	Tool functions	Learning mode: Additional learning Standard mode: Mask outline, Masking function, Color extraction/exclusion^1, Color histogram function^1, Monochrome histogram function^*2, Scaling function
	Utilities	Failing sensor list, Failure hold, Test run, I/O monitor, Security settings, Simulator^*7
Input	Type	Switchable between non-voltage input and voltage input For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs	8 (IN1 to IN8)
	Function	IN1: External trigger, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Clear error, External master image registration, SD card save cancel
Output	Type	Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA, residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA, residual voltage of 2 V or less
	Number of outputs	8 (OUT1 to OUT8)
	Function	Enable by assigning optional functions Assignable functions: Total judgment (OK/NG), Run, Busy, Ready, Strobe, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card error
Ethernet	Standard	100BASE-TX/10BASE-T
	Connector	RJ45 8-pin connector
Network function		FTP client, SNTP client
Interface compatibility	Built-in Ethernet	EtherNet/IP™, PROFINET, TCP/IP non-procedure communication
	Communication unit	EtherCAT^Ⓡ, CC-Link, DeviceNet^Ⓡ, PROFIBUS, RS-232C^*8
Expanded memory		SD card (SD/SDHC) ^*9
Rating	Power voltage	24 VDC ±10% (including ripple)
	Current consumption	1.8 A or less (including communication unit and output load)
Environmental resistance	Ambient temperature	0 to +50°C 32 to 122°F (No freezing)
	Relative humidity	35 to 85% RH (No condensation)
Material		Main unit case: PC, Power connector: PA/POM, I/O connector: PA, Sensor head connector: Zinc + Ni plating/PA, Ethernet connector: Copper alloy + Ni plating, Main unit rear heat sink: Aluminum, Main unit rear DIN rail fixing tab: POM, Nameplate: PC
Weight		Approx. 330 g
^1 Color type only. ^2 Monochrome type only. ^3 Tools can be installed by programs. ^4 Saves to the sensor amplifier’s internal memory. The images saved to the sensor amplifier can be backed up to a USB memory stick inserted into the control panel (IV2-CP50) or to the PC where the software for the IV2 Series (IV2-H1) is being used. ^5 Learning mode only. ^6 Can also be displayed on the control panel (IV2-CP50) or the software for the IV2 Series (IV2-H1). ^7 Usable on the software for the IV2 Series (IV2-H1). ^8 When a communication unit (DL Series) is connected. ^*9 Use only products recommended by KEYENCE.

Keyence CV-X250FP Keyence

$3,010.77

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence LV-21AP Keyence

$238.20

Only 10 units left

Specifications

Model		LV-21AP
Type		PNP output
Main unit/expansion unit		Main unit
Control output		PNP open-collector x 2 channels, 30 VDC max., max. 100 mA, residual voltage (1.0 V max.)
Response speed		FINE : 80 µs , TURBO : 500 µs , SUPER , TURBO : 4 ms
Number of interference preventive units		FINE : None , TURBO : 2 units , SUPER : 4 units
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Unit expansion		Up to 7 additional expansion units can be installed (8 units including the main unit),
Rating	Power voltage	12 to 24 VDC, Ripple (P-P) 10 % or less
	Power consumption	1.5 W max. (125 mA max. for 12 V, 62.5 mA max. for 24 V)
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing) ^*1
	Relative humidity	35 to 85 % RH (No condensation)
Material	Main unit	Polycarbonate
	Case
Weight		Approx. 75 g
^*1 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 2 to 5 units: -10 to +50 °C 14 to 122 °F When 6 to 7 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA.

Keyence FS-N41N Keyence

$198.89

In stock, 24 units

Specifications

Model		FS-N41N
Type		Cable
Output		NPN
Main unit/expansion unit		Main unit
Response time		23 µs (S-HSPD^1) /50 µs (HSPD^2) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER) /4 ms (ULTRA) /16 ms (MEGA) /64 ms (TERA)
Number of control outputs		1
Number of external inputs		―
Light source LED		Transmitter side: Red, four-element LED (wavelength: 660 nm)
Control output		Open-collector, 30 V or less 100 mA or less per output, 100 mA or less total for 2 outputs (when used as a solitary unit) /20 mA or less (when used as an expansion unit) Residual voltage: 1.4 V or less (output current: 10 mA or less) /2 V or less (output current: 10 to 100 mA)
External input		Input time: 2 ms (ON) /20 ms (OFF) or longer^*3
Unit expansion		Up to 16 units (17 units connected in total including the main unit) . However, each dual output type will be treated as two expansion units.
Protection circuit		Protection against reverse power connection, output overcurrent, output surge, and reverse output connection
Mutual interference prevention		S-HSPD/HSPD: 0 units, FINE: 4 units, TURBO/SUPER/ULTRA/MEGA/TERA: 8 units (The mutual interference prevention values are twice those shown here when Double is set.)
Power supply	Power voltage	10 to 30 VDC (including 10 % ripple (P-P) or less) , class 2 or LPS^*4
	Power consumption	During normal operation: 870 mW or less (34 mA or less at 24 V/62 mA or less at 12 V) ECO ON: 800 mW or less (31 mA or less at 24 V/56 mA or less at 12 V) ECO FULL: 710 mW or less (28 mA or less at 24 V/49 mA or less at 12 V)^*5
Environmental resistance	Ambient light	Incandescent lamp: 20,000 lx or less, sunlight: 30,000 lx or less
	Ambient temperature	-20 °C -4 °F to +55 °C +131 °F (no freezing)^*6
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
	Shock resistance	500 m/s²; 3 times each for X, Y, and Z axes
Case material		Main unit and cover: polycarbonate
Weight		Approx. 78 g
^1 Restrictions when S-HSPD is selected Area detection, Area % Mode, DATUM, Rising edge, and Falling edge cannot be selected for Detection Mode. Output timer, Limit Detection, and Display Gain cannot be used. FULL cannot be selected for the ECO function. ^2 Restrictions when HSPD is selected Display Gain cannot be used. ^3 The input time becomes 25 ms (ON)/25 ms (OFF) when external calibration input is selected. ^4 When expanding the system to 9 or more units, use a power supply voltage of 12 V or higher. ^5 The load current is excluded. The power consumption including the load when the maximum number of units are connected is 38 W max. ^6 When expanded by 1 to 2 units: -20°C -4°F to +55°C +131°F. When expanded by 3 to 10 units: -20°C -4°F to +50°C +122°F. When expanded by 11 to 16 units: -20°C -4°F to +45°C +113°F. When using 2 outputs, 1 unit is counted as 2 units. The prescribed values for the ambient temperature assume that the sensor amplifi er has been mounted on a DIN rail installed on a metal surface. Exercise special care when installing the product in an airtight space.

Sick VS/VE18-3P3212THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-4N3740THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE12-2P430 THROUGH-BEAM SENS. Sick

$515.07

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-4P3212THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick ICR803-B0201 Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-2T2430 THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-3P3240THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-3P3740THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Sick VS/VE18-3F3440THROUGH-BEAM SENS. Sick

$0.00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.