Distance & Measurement Sensors

$2,416.16

Only 1 unit left

Specifications

Model		LK-CC100
Type		CC-Link communication unit dedicated to LK-G5000 Series
Network connection	Supported CCLink version	Ver. 1.10 (Extended cyclic setting: Single) Ver. 2.00 (Extended cyclic setting: Double or more)^1^2
	Master unit	CLPA-certified master unit (CC-Link Ver. 2.00/Ver. 1.10)
	No. of occupied stations	1 to 4
	Communication speed	156kbps、625kbps、2.5Mbps、5Mbps、10Mbps
	Connection cable	Dedicated CC-Link cable supporting Ver. 1.10 (Shielded 3-core twisted-pair cable: OP-79426, OP-79427)
	Maximum total cable extension length	156kbps…1200m、 625kbps…900m、 2.5Mbps…400m、 5Mbps…160m、 10Mbps…100m
	Station type	Remote device station
Power supply	Power supply voltage	24 VDC ±10 % (supplied from controller)
	Maximum current consumption	200mA or less
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 300 g
^1 The LK-G5000 Series supports the "extended cyclic transmission" and "station-to-station cable length relaxation" of CC-Link Ver. 2.00. ^2 CC-Link is a registered trademark of Mitsubishi Electric Corporation.

Keyence LK-G32 Keyence

$1,491.33

In stock, 24 units

Specifications

Model		LK-G32
Reference distance		Diffused reflection: 30 mm 1.18", Specular reflection: 23.5 mm 0.93"
Measuring range		Diffused reflection: ±5 mm ±0.2", Specular reflection: ±4.5 mm ±0.18"^1^2
Light source	Type	Red semiconductor laser
	Wavelength	655 nm (visible light)
	Laser Class	Class II (FDA CDRH 21CFR PART1040.10)
	Output	0.95 mW
Spot diameter (at reference distance)		Approx. ø30 µm ø0.0012"
Linearity		±0.05 % of F.S. (F.S.= ±5 mm ±0.2")^*3
Repeatability		0.05 µm^*4
Sampling frequency		20 / 50 / 100 / 200 / 500 / 1,000 µs (Selectable from 6 levels)
LED display		Near the center of the measurement: Green lights Within the measurement area: Orange lights Outside the measurement area: Orange flashing
Temperature characteristics		0.01 % of F.S./°C (F.S.= ±5 mm ±0.2")
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Aluminum die-cast
Weight		Approx. 280 g (including the cable)
^1 The range is obtained by measuring KEYENCE's standard target (ceramic). ^2 When the sampling rate is 20 µs, the range becomes +1.8 mm +0.07" (FAR side) to -5 mm -0.20" (NEAR side) for Diffused reflection, and +1.6 mm +0.06" (FAR side) to -4.5 mm -0.18" (NEAR side) ^3 The range is obtained by measuring KEYENCE's standard target (ceramic) with the Standard mode. ^4 The range is obtained by measuring KEYENCE's standard (SUS) with 4,096 times of averaging at the reference distance.

Keyence LK-63001P Keyence

$909.71

Only 3 units left

Buy the Keyence LK-63001P - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence LK-63001P is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence LR-X100 Keyence

$462.57

In stock, 12 units

Specifications

Model		LR-X100
Type		Cable Type
Detecting Distance		25.0 to 100.0 mm 0.98" to 3.94"
Standard Detectable Deviation		1.0 mm 0.04"
Display Resolution		0.1 mm 0.004"
Spot Size		Approx. 0.3 mm × 2 mm 0.012" × 0.08" (at a detecting distance of 100 mm 3.94")
Response Time		500 µs^*1/1 ms/3 ms/10 ms/200 ms Selectable
Light Source	Type	Green laser (505 nm)
	Laser Class	Class 1 Laser Product (IEC60825-1, FDA (CDRH), Part1040.10^*2)
IO-Link		Specification v1.1/COM2 (38.4 kbps)
Functions	Timer Function	Timer OFF/Off-delay/On-delay/One-shot/On-Off delay/On-delay One-shot
I/O	Control Output	NPN open collector/PNP open collector, N.O./N.C selectable.　　^*3 30 VDC or lower, 50 mA or lower, Residual voltage 2 V or lower
	External Input	External Set/Laser OFF/Zero Shift/Hold Reset/Gyro Alert RST selectable　　^*3 Short circuit current - NPN: 1 mA or lower, PNP: 2 mA or lower Input time 3 ms or more ON, 20 ms or more OFF (25 ms or more ON, 25 ms or more OFF when External Set is selected only)
Protection Circuit		Protection against reverse power connection, protection against output overcurrent, protection against output surge, protection against reverse output connection
Power supply	Power voltage	16 to 30 VDC (including 10% ripple (P-P) or less), class 2
	Power consumption	During normal operation: 970 mW (38 mA or lower at 24 V, 53 mA or lower at 16 V) (Excluding Load Current) ECO ON/ALL: 821 mW (32 mA or lower at 24 V, 44 mA or lower at 16 V) (Excluding Load Current)
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient light	Incandescent lamp: 16000 lux or less Sunlight: 16000 lux or less
	Ambient temperature	-10°C to +50°C 14°F to + 122°F (no freezing)
	Relative humidity	35 to 85% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power Spectral Density: 0.816 G²/Hz for X, Y and Z axes
	Shock resistance	1000 m/s² (100G) 6 times each for X, Y, and Z axes
Material		Head Case: SUS316L; Head Lens Cover: PSU Head Gasket: FKM (lens cover), EVM (cable) Cable: PVC Amplifier Case: PBT; Amplifier Display, Indicator: PAR; Amplifier Gasket: NBR; Button: POM
Accessories		Instruction manual, laser warning label
Weight		Approx. 90 g
^1 If 500 µs is selected, the following limitations apply. · Only 2-point calibration can be performed. · The detection range masking is set during calibration. (Manual setting of the masking range is not supported.) · Output 2 is limited to an alarm output for errors and gyro issues, and standard/area cannot be used. ^2 Classification performed based on IEC60825-1 standards in accordance with FDA (CDRH) Laser Notice. ^*3 The I/O can be selected from the following combinations. Control output × 2, Control output + External input

Keyence LK-G3000P Keyence

$1,630.22

Only 5 units left

Buy the Keyence LK-G3000P - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence LK-G3000P is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence LK-G5001PV Keyence

$2,507.38

Only 6 units left

Specifications

Model		LK-G5001PV^1^2
Separate type		LK-G5001P/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	PNP open-collector output
	General comparator output
Expansion connector	TIMING input	Voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	PNP open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 PNP open-collector output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Keyence LK-G507 Keyence

$3,450.54

Only 5 units left

Specifications

Model		LK-G507
Reference distance		Diffused reflection: 500 mm 19.69", Specular reflection: 497.5 mm 19.59"
Measuring range		Diffused reflection: -250 to +500 mm -9.84" to 19.69", Specular reflection: -249 to +498 mm -9.80" to 19.61"^1^2
Light source	Type	Red semiconductor laser
	Wavelength	655 nm (visible light)
	Laser Class	Class II (FDA CDRH 21CFR PART1040.10)
	Output	0.95 mW
Spot diameter (at reference distance)		Approx. 300 x 9,500 µm 0.0118" x 0.3740"
Linearity		±0.05 % of F.S. (±250 µm ±0.0098")^3^4 -250 to +250 mm -9.84" to +9.84" High-accuracy range: ±0.02 % of F.S. (±100 µm ±0.0039") -250 to -50 mm -9.84" to -1.97" Long range: ±0.1 % of F.S. (±500 µm ±0.0197") -250 to +500 mm -9.84" to +19.69" (F.S. = ±250 mm ±9.84")^*5
Repeatability		2 µm 0.000079"^*6
Sampling frequency		20 / 50 / 100 / 200 / 500 / 1,000 µs (Selectable from 6 levels)
LED display		Near the center of the measurement: Green lights Within the measurement area: Orange lights Outside the measurement area: Orange flashing
Temperature characteristics		0.01 % of F.S./°C (F.S.= ±250 mm ±9.84")
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient light	Incandescent lamp or Fluorescent lamp: 5,000 lux max.
	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Aluminum die-cast
Weight		Approx. 380 g (including the cable)
^1 The range is obtained by measuring KEYENCE's standard target (ceramic). ^2 When the sampling rate is 20 µs, the range becomes -230 mm -9.06" (NEAR side) to -250 mm -9.84" (NEAR side) for Diffused reflection. When the sampling rate is 20 µs, the range becomes -230 mm -9.06" (NEAR side) to -249 mm -9.80" (NEAR side) for specular reflection. When the sampling rate is 50 µs, the range becomes -125 mm -4.92" (NEAR side) to -250 mm -9.84" (NEAR side) for Diffused reflection. When the sampling rate is 50 µs, the range becomes -125 mm -4.92" (NEAR side) to -249 mm -9.80" (NEAR side) for specular reflection. ^3 All are calculated at F.S. = ±250 mm ±9.84". ^4 "High accuracy range" and "long range" refer to the linearity when those ranges are used. ^5 The range is obtained by measuring KEYENCE's standard target (ceramic) with the Standard mode. ^6 The range is obtained by measuring KEYENCE's standard (SUS) with 4,096 times of averaging at the reference distance.

Keyence LJ-S040 Keyence

$37,597.50

Only 1 unit left

Specifications

Model			LJ-S040
Reference distance			70 mm 2.76" ^*1
Measurement range	Z-axis (height)		±18 mm ±0.71" (F.S.=36 mm 1.42")
	X-axis (width)	NEAR side	31 mm 1.22"
		Reference distance	35 mm 1.38"
		FAR side	39 mm 1.54"
	Y-axis	Reference distance	80 mm 3.15"
XY data interval			12.5 μm 0.0005"
Number of XY data points			3200 × 6400
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		0.5 μm 0.000020" ^*4
	XY (distance)		1 μm 0.000039" ^*5
Linearity	Standard area		±0.02% of F.S. ^*6
	High-accuracy area		—
Imaging time			Min. 0.2 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 4.0 A (at 19.2 V), 3.2 A (at 24 V) ^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 2600 g 5.73 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-GC30 Keyence

$0.00

Sold Out

Specifications

Model				LJ-GC30
Type				Cable between the head and controller
Applicable product				LK-G3000 series
Number included				1
Cable end				Straight
Length				30 m 98.42'
Weight				Approx. 2,000 g

Keyence LR-ZH500C3P Keyence

$414.33

Only 8 units left

Specifications

Model		LR-ZH500C3P^1^2
Type		U.C.D. Function Distance based laser sensor
Appearance		Rectangular
Output		PNP
Cable connection		M8 connector, 3-pin
Detectable distance		35 to 500 mm 1.38" to 19.69"(465 to 0)^*3
Standard detectable deviation		35 to 180 mm 1.38" to 7.09": 9 mm 0.35" 180 to 300 mm 7.09" to 11.81": 25 mm 0.98" 300 to 400 mm 11.81" to 15.75": 40 mm 1.57" 400 to 500 mm 15.75" to 19.69": 50 mm 1.97"
Display resolution		1 to 5 (1 to 5 mm 0.04" to 0.20")
Spot size		Approx. ø3 mm ø0.12"
Response time		1.5 ms / 10 ms / 50 ms selectable
Light source	Type	Red laser (660 nm)
	Laser class	Class 2 laser product (IEC60825-1) Class II Laser product (FDA(CDRH) Part1040.10)
Function	Indicator	3-digit 7-segment display (white), output indicator (yellow), DATUM indicator (orange), 1 spot indicator (green)
	Timer	OFF/ON delay/OFF delay/One-shot
Specifications	Power voltage	10 to 30 VDC, including 10% ripple (P-P), Class 2 or LPS
	Power consumption	450 mW or less (18 mA or less at 24 V, 34 mA or less at 12 V)
	Control output	PNP Open collector, Applied voltage 30 VDC or less, Control current 100 mA or less, Residual voltage 1.2 V or less at 10 mA or less, 2 V or less at 10 to 100 mA
	Protection circuit	Protection against reverse power connection, output overcurrent, output surge, reverse output connection
	Output operation	Light-ON / Dark-ON selectable
Environmental resistance	Enclosure rating	IP68 (IEC60529), IP69K (DIN40050-9), NEMA 4X, 6P, 13 (NEMA250), ECOLAB^4, Diversey^4
	Insulation resistance	20 MΩ or more (500 VDC)
	Ambient light	Incandescent lamp: 10,000 lux or less Sunlight: 20,000 lux or less at 250 mm 9.84"^5 Incandescent lamp: 2,000 lux or less Sunlight: 4,000 lux or less at 500 mm 19.69"^5
	Ambient temperature	-10 to +50 °C 14 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-25 to +75 °C -13 to 167 °F (No freezing)
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: SUS316L, Display: PES, Lens cover: PMMA with scratch-resistant coating, Packing/Connector ring: FKM
Accompanying items		Instruction Manual, FDA warning/certification/identification label, Laser warning/explanation labels
Weight		Approx. 55 g
^1 IO-Link specification v.1.1/COM2 (38.4 kbps) is supported. You can download a setup file from the KEYENCE website. If using the product in an environment in which downloading files over the internet is not possible, contact your nearest KEYENCE office. ^2 M8 connector (3-pin) type does not include the external input function. ^3 Display readings can be used as a guide for the detecting distance. When the setting value is tuned, the readout shifts. When the value exceeds "-99", "-FF" is displayed. ^4 Have passed resistance tests with cleaning agents from multiple manufactures. ^*5 When the response time is 10 ms

Keyence LR-X50C Keyence

$495.53

Only 9 units left

Specifications

Model		LR-X50C
Type		M8 Connector Type^*1
Detecting Distance		25.0 to 50.0 mm 0.98" to 1.97"
Standard Detectable Deviation		0.5 mm 0.02"
Display Resolution		0.1 mm 0.004"
Spot Size		Approx. 0.2 mm × 1.5 mm 0.008" × 0.06" (at a detecting distance of 50 mm 1.97")
Response Time		500 µs^*2/1 ms/3 ms/10 ms/200 ms Selectable
Light Source	Type	Green laser (505 nm)
	Laser Class	Class 1 Laser Product (IEC60825-1, FDA (CDRH), Part1040.10^*3)
IO-Link		Specification v1.1/COM2 (38.4 kbps)
Functions	Timer Function	Timer OFF/Off-delay/On-delay/One-shot/On-Off delay/On-delay One-shot
I/O	Control Output	NPN open collector/PNP open collector, N.O./N.C selectable.　　^*4 30 VDC or lower, 50 mA or lower, Residual voltage 2 V or lower
	External Input	External Set/Laser OFF/Zero Shift/Hold Reset/Gyro Alert RST selectable　　^*4 Short circuit current - NPN: 1 mA or lower, PNP: 2 mA or lower Input time 3 ms or more ON, 20 ms or more OFF (25 ms or more ON, 25 ms or more OFF when External Set is selected only)
Protection Circuit		Protection against reverse power connection, protection against output overcurrent, protection against output surge, protection against reverse output connection
Power supply	Power voltage	16 to 30 VDC (including 10% ripple (P-P) or less), class 2
	Power consumption	During normal operation: 970 mW (38 mA or lower at 24 V, 53 mA or lower at 16 V) (Excluding Load Current) ECO ON/ALL: 821 mW (32 mA or lower at 24 V, 44 mA or lower at 16 V) (Excluding Load Current)
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient light	Incandescent lamp: 16000 lux or less Sunlight: 16000 lux or less
	Ambient temperature	-10°C to +50°C 14°F to + 122°F (no freezing)
	Relative humidity	35 to 85% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power Spectral Density: 0.816 G²/Hz for X, Y and Z axes
	Shock resistance	1000 m/s² (100G) 6 times each for X, Y, and Z axes
Material		Head Case: SUS316L; Head Lens Cover: PSU Head Gasket: FKM (lens cover), EVM (cable) Cable: PVC Amplifier Case: PBT; Amplifier Display, Indicator: PAR; Amplifier Gasket: NBR; Button: POM Amplifier M8 Connector: SUS303
Accessories		Instruction manual, laser warning label
Weight		Approx. 35 g
^1 Ensure the cable length is 30 m 98.4' or less for the M8 connector type. Ensure the cable length is 20 m 65.6' or less when connecting via IO-Link. ^2 If 500 µs is selected, the following limitations apply. · Only 2-point calibration can be performed. · The detection range masking is set during calibration. (Manual setting of the masking range is not supported.) · Output 2 is limited to an alarm output for errors and gyro issues, and standard/area cannot be used. ^3 Classification performed based on IEC60825-1 standards in accordance with FDA (CDRH) Laser Notice. ^4 The I/O can be selected from the following combinations. Control output × 2, Control output + External input