keyence

€420,95

Only 4 units left

Specifications

Model		AP-C31K
Type		Negative pressure, NPN
Rated pressure		0 to -29.9 inchHg
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 0.43" (11 mm)) Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Display resolution		Normal mode: 0.1 inchHg, Focus mode: 0.01 inchHg
Power consumption	Normal	12 V: 720 mW (60 mA) or less, 24 V: 960 mW (40 mA) or less
	Eco mode	12 V: 480 mW (40 mA) or less, 24 V: 720 mW (30 mA) or less
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of F.S.)^*1
Response time (Chattering prevention function)		2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	NPN open collector 100 mA max. (at 40 V or below) with max. residual voltage of 1 V, 2 outputs (NO or NC selectable)
Pressure port		NPT 1/8 180 ° rotation
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Pressure resistance	500 kPa
	Ambient temperature	0 to 50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate, Pressure port: Zinc die-casting
Accessories		Power supply cord (6.6' 2-m with connector)
Weight		Approx. 30 g (without cable) /Approx. 85 g (with 6.6' 2-m cable)
^*1 A standard of 0.2 % of FS applies while in focus mode.

Keyence AP-C31KP Keyence

€0,00

Sold Out

Specifications

Model		AP-C31KP
Type		Negative pressure, PNP
Rated pressure		0 to -29.9 inchHg
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 0.43" (11 mm)) Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Display resolution		Normal mode: 0.1 inchHg, Focus mode: 0.01 inchHg
Power consumption	Normal	12 V: 900 mW (75 mA) or less, 24 V: 1,320 mW (55 mA) or less
	Eco mode	12 V: 600 mW (50 mA) or less, 24 V: 960 mW (40 mA) or less
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of F.S.)^*1
Response time (Chattering prevention function)		2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	PNP open collector 100 mA max. (at 30 V or below) with max. residual voltage of 1 V, 2 outputs (NO or NC selectable)
Pressure port		NPT 1/8 180 ° rotation
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Pressure resistance	500 kPa
	Ambient temperature	0 to 50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate, Pressure port: Zinc die-casting
Accessories		Power supply cord (6.6' 2-m with connector)
Weight		Approx. 30 g (without cable) /Approx. 85 g (with 6.6' 2-m cable)
^*1 A standard of 0.2 % of FS applies while in focus mode.

Keyence AP-C31P Keyence

€269,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C31WP Keyence

€296,95

Only 3 units left

Buy the Keyence AP-C31WP - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-C31WP is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence AP-C33C Keyence

€512,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C33CP Keyence

€440,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C33K Keyence

€357,95

Only 1 unit left

Specifications

Model		AP-C33K
Type		Positive pressure, NPN
Rated pressure		0 to 145.0 Psi
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 0.43" (11 mm)) Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Display resolution		Normal mode: 0.2 Psi, Focus mode: 0.02 Psi
Power consumption	Normal	12 V: 720 mW (60 mA) or less, 24 V: 960 mW (40 mA) or less
	Eco mode	12 V: 480 mW (40 mA) or less, 24 V: 720 mW (30 mA) or less
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of F.S.)^*1
Response time (Chattering prevention function)		2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	NPN open collector 100 mA max. (at 40 V or below) with max. residual voltage of 1 V, 2 outputs (NO or NC selectable)
Pressure port		NPT 1/8 180 ° rotation
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Pressure resistance	1.5 MPa
	Ambient temperature	0 to 50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate, Pressure port: Zinc die-casting
Accessories		Power supply cord (6.6' 2-m with connector), Unit seal
Weight		Approx. 30 g (without cable) /Approx. 85 g (with 6.6' 2-m cable)
^*1 A standard of 0.2 % of FS applies while in focus mode.

Keyence AP-C33KP Keyence

€388,95

Only 6 units left

Specifications

Model		AP-C33KP
Type		Positive pressure, PNP
Rated pressure		0 to 145.0 Psi
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 0.43" (11 mm)) Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Display resolution		Normal mode: 0.2 Psi, Focus mode: 0.02 Psi
Power consumption	Normal	12 V: 900 mW (75 mA) or less, 24 V: 1,320 mW (55 mA) or less
	Eco mode	12 V: 600 mW (50 mA) or less, 24 V: 960 mW (40 mA) or less
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of F.S.)^*1
Response time (Chattering prevention function)		2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	PNP open collector 100 mA max. (at 30 V or below) with max. residual voltage of 1 V, 2 outputs (NO or NC selectable)
Pressure port		NPT 1/8 180 ° rotation
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Pressure resistance	1.5 MPa
	Ambient temperature	0 to 50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate, Pressure port: Zinc die-casting
Accessories		Power supply cord (6.6' 2-m with connector), Unit seal
Weight		Approx. 30 g (without cable) /Approx. 85 g (with 6.6' 2-m cable)
^*1 A standard of 0.2 % of FS applies while in focus mode.

Keyence AP-C33P Keyence

€361,95

Only 5 units left

Buy the Keyence AP-C33P - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-C33P is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence AP-C33PFAST Keyence

€279,95

Only 5 units left

Buy the Keyence AP-C33PFAST - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-C33PFAST is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence AP-C33W Keyence

€0,00

Sold Out

Buy the Keyence AP-C33W - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-C33W is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence AP-C33WP Keyence

€354,95

Only 8 units left

Buy the Keyence AP-C33WP - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-C33WP is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence AP-C35 Keyence

€377,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C40P Keyence

€323,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C40W Keyence

€269,95

Only 1 unit left

Specifications

Model		AP-C40W
Type		Amplifier Unit, NPN
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Set and display range		-15 to +110 % of F.S.^*1
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 11 mm 0.43"), Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 780 mW (65 mA) max., 24 V: 1,080 mW (45 mA) max.
	Eco mode	12 V: 540 mW (45 mA) max., 24 V: 840 mW (35 mA) max.
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of FS; high-resolution/focus mode: 0.1 % of F.S.)
Response time (Chattering prevention function)		1 (in high-speed mode only), 2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	NPN open collector 100 mA max. (at 40 V or below) with max., residual voltage of 1 V, 2 outputs (NO or NC selectable)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate
Accessories		Power supply code (2-m 6.6' cable with connector), Head connector, and Unit seal
Weight		Approx. 74 g (with 2-m 6.6' cable)
^*1 The focus range applies while in focus mode only.

Keyence AP-C40WP Keyence

€295,95

Only 3 units left

Specifications

Model		AP-C40WP
Type		Amplifier Unit, PNP
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Set and display range		-15 to +110 % of F.S.^*1
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 11 mm 0.43"), Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 960 mW (80 mA) max., 24 V: 1,400 mW (60 mA) max.
	Eco mode	12 V: 660 mW (55 mA) max., 24 V: 1,080 mW (45 mA) max.
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of FS; high-resolution/focus mode: 0.1 % of F.S.)
Response time (Chattering prevention function)		1 (in high-speed mode only), 2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	PNP open collector 100 mA max. (at 30 V or below) with max., residual voltage of 1 V, 2 outputs (NO or NC selectable)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate
Accessories		Power supply code (2-m 6.6' cable with connector), Head connector, and Unit seal
Weight		Approx. 74 g (with 2-m 6.6' cable)
^*1 The focus range applies while in focus mode only.

Keyence AP-N10 Keyence

€458,95

Only 1 unit left

Specifications

Model		AP-N10
Type		Single output type
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44, AP-48
Configuration/Display range		-15 to +110 % of F.S.
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44/48: Standard mode 0.1 kPa, High resolution mode 0.01 kPa AP-43: Standard mode 0.001 MPa, High resolution mode 0.1 kPa
Power consumption	Normal	770 mW or less (at 24 V, 32 mA or less/at 12 V, 54 mA or less)
	Eco mode	560 mW or less (at 24 V, 23 mA or less/at 12 V, 37 mA or less)
Expansion units		Max. 16 units (Dual output type is counted as 2 units.)^*1
Control output(s)		1^*2
Display temperature characteristic		±1 % of F.S. (When the temperature varies from 25 °C 77 °F)
Response time (Chattering prevention function)		1 ms/2.5 ms/5 ms/100 ms/500 ms/1,000 ms/5,000 ms selectable
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % max. Class2
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material		Main unit and cover: Polycarbonate
Weight		Approx. 20 g
^1 Can connect to other N-bus sensor amplifiers. N-bus represents the wire-saving system for KEYENCE-manufactured sensor amplifiers. ^2 Number of outputs when connected to the communication unit NU Series. There are no control output wires. ^*3 11 to 16 units connected: 0 to +45 °C 32 to 113 °F (When the sensor amplifier is installed on DIN rail on a metal plate)

Keyence AP-N10D Keyence

€0,00

Sold Out

Specifications

Model		AP-N10D
Type		Dual output type
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44, AP-48
Configuration/Display range		-15 to +110 % of F.S.
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44/48: Standard mode 0.1 kPa, High resolution mode 0.01 kPa AP-43: Standard mode 0.001 MPa, High resolution mode 0.1 kPa
Power consumption	Normal	770 mW or less (at 24 V, 32 mA or less/at 12 V, 54 mA or less)
	Eco mode	560 mW or less (at 24 V, 23 mA or less/at 12 V, 37 mA or less)
Expansion units		Max. 16 units (Dual output type is counted as 2 units.)^*1
Control output(s)		2^*2
Display temperature characteristic		±1 % of F.S. (When the temperature varies from 25 °C 77 °F)
Response time (Chattering prevention function)		1 ms/2.5 ms/5 ms/100 ms/500 ms/1,000 ms/5,000 ms selectable
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % max. Class2
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material		Main unit and cover: Polycarbonate
Weight		Approx. 20 g
^1 Can connect to other N-bus sensor amplifiers. N-bus represents the wire-saving system for KEYENCE-manufactured sensor amplifiers. ^2 Number of outputs when connected to the communication unit NU Series. There are no control output wires. ^*3 11 to 16 units connected: 0 to +45 °C 32 to 113 °F (When the sensor amplifier is installed on DIN rail on a metal plate)

Keyence AP-V41A Keyence

€708,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-V41AW Keyence

€0,00

Sold Out

Specifications

Model		AP-V41AW
Type		Amplifier Unit, NPN
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Set and display range		-15 to +110 % of F.S.^*1
Display		4 1/2-digit, 2-color, 7-segment LED (Character height: 4.5 mm 0.18"), AI indicator (green), Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 720 mW (60 mA) max., 24 V: 960 mW (40 mA) max.
	Eco mode	12 V: 480 mW (40 mA) max., 24 V: 720 mW (30 mA) max.
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of FS; high-resolution/focus mode: 0.1 % of F.S.)
Response time (Chattering prevention function)		1 (in high-speed mode only), 2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	NPN open collector 100 mA max. (at 40 V or below) with max., residual voltage of 1 V, 2 outputs (NO or NC selectable)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Accessories		Mounting bracket, Head connector
Weight		Approx. 80 g (with 2-m 6.6' cable)
^*1 The focus range applies while in focus mode only.

Keyence AP-V41AWP Keyence

€357,95

Only 2 units left

Specifications

Model		AP-V41AWP
Type		Amplifier Unit, PNP
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Set and display range		-15 to +110 % of F.S.^*1
Display		4 1/2-digit, 2-color, 7-segment LED (Character height: 4.5 mm 0.18"), AI indicator (green), Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Repeatability		±0.2 % of F.S.
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 720 mW (60 mA) max., 24 V: 960 mW (40 mA) max.
	Eco mode	12 V: 480 mW (40 mA) max., 24 V: 720 mW (30 mA) max.
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of FS; high-resolution/focus mode: 0.1 % of F.S.)
Response time (Chattering prevention function)		1 (in high-speed mode only), 2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	PNP open collector 100 mA max. (at 30 V or below) with max., residual voltage of 1 V, 2 outputs (NO or NC selectable)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Accessories		Mounting bracket, Head connector
Weight		Approx. 80 g (with 2-m 6.6' cable)
^*1 The focus range applies while in focus mode only.

Keyence AP-V41W Keyence

€438,95

Only 3 units left

Specifications

Model		AP-V41W
Type		Amplifier Unit, NPN
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Display		4 1/2-digit, 2-color, 7-segment LED (Character height: 4.5 mm 0.18"), AI indicator (green) Display cycle: 10 times/s
Operation indicator		Red LED × 2 (corresponding to control output 1 and control output 2)
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 720 mW (60 mA) max., 24 V: 960 mW (40 mA) max.
	Eco mode	12 V: 480 mW (40 mA) max., 24 V: 720 mW (30 mA) max.
Display temperature characteristic		±1 % of F.S. or less
Hysteresis		Standard mode: 0.5 % of F.S., high-resolution mode: 0.1 % of F.S., hysteresis variable mode (F-2): variable
Response time (Chattering prevention function)		1/2.5/5/100/500 ms (selectable; 1 ms is used when high-speed mode is selected)
I/O	Analog output	1 to 5 V, output impedance: 1 kΩ or less (switchable with zero shift input)
	Zero-shift input	Input time: 2 ms or more (switchable with analog output)
	Control output	Maximum NPN open-collector output: 100 mA (40 V or less), residual voltage: 1 V or less, 2 outputs (N.O./N.C. switchable)^*1
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Accessories		Mounting bracket, head connection connector
Weight		Approx. 80 g (with 2 m cable)
^*1 20 mA or less when extended

Keyence AP-V41WP Keyence

€809,95

Only 2 units left

Specifications

Model		AP-V41WP
Type		Amplifier Unit, PNP
Applicable sensor head		AP-41M, AP-41, AP-43, AP-44
Display		4 1/2-digit, 2-color, 7-segment LED (Character height: 4.5 mm 0.18"), AI indicator (green) Display cycle: 10 times/s
Operation indicator		Red LED × 2 (corresponding to control output 1 and control output 2)
Display resolution		AP-41M/41/44: Standard mode 0.1 inchHg, High-resolution/Focus mode 0.01 inchHg AP-43: Standard mode 0.01 kgf/cm², High-resolution/Focus mode 0.02 Psi
Power consumption	Normal	12 V: 840 mW (70 mA) max., 24 V: 1,200 mW (50 mA) max.
	Eco mode	12 V: 600 mW (50 mA) max., 24 V: 960 mW (40 mA) max.
Display temperature characteristic		±1 % of F.S. or less
Hysteresis		Standard mode: 0.5 % of F.S., high-resolution mode: 0.1 % of F.S., hysteresis variable mode (F-2): variable
Response time (Chattering prevention function)		1/2.5/5/100/500 ms (selectable; 1 ms is used when high-speed mode is selected)
I/O	Analog output	1 to 5 V, output impedance: 1 kΩ or less (switchable with zero shift input)
	Zero-shift input	Input time: 2 ms or more (switchable with analog output)
	Control output	Maximum PNP open-collector output: 100 mA (30 V or less), residual voltage: 1 V or less, 2 outputs (N.O./N.C. switchable)^*1
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Polycarbonate
Accessories		Mounting bracket, head connection connector
Weight		Approx. 80 g (with 2 m cable)
^*1 20 mA or less when extended

Keyence AP-V42A Keyence

€0,00

Sold Out

Buy the Keyence AP-V42A - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence AP-V42A is a direct drop-in replacement for existing installations and ships ready for integration.