Measurement Sensors

Showing 313 - 336 of 719 products

€2.178,95

Only 7 units left

Specifications

Model			LJ-G030
Mounting			Diffuse reflective
Reference distance			30 mm 1.18"
Measuring range	Z-axis (Height)		±10 mm ±0.39"
	X-axis (Width)	Near	20 mm 0.79"
		Reference distance	22 mm 0.87"
		Far	25 mm 0.98"
Light source	Type		Red semiconductor laser
	Wavelength		655nm (Visible light), Class 2 laser product (JIS C6802)
	Output		0.95 mW
	Laser Class		Class II Laser Product (FDA (CDRH) 21CFR PART1040.10), Class 2 Laser Product (IEC 60825-1)
Spot shape (at reference distance)			Approx 40 µm x 25 mm 0.001575" x 0.98"
Repeatability	Z-axis (Height)		1 µm 0.000040"^*1
	X-axis (Width)		5 µm 0.000197"^*2
Linearity Z-axis (Height)			±0.1% of F.S.^*3
Sampling cycle (trigger interval)			3.8 ms^*4
Temperature characteristics			0.02% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529)
	Ambient light		Incandescent lamp or fluorescent lamp: 5,000 lux max.^*5
	Ambient temperature		0 to +50 °C 32 to 122 °F
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material			Aluminum
Weight			Approx. 290 g
^1 The value obtained after 64 times averaging at the reference distance.The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^2 The value obtained after 64 times averaging at the reference distance.The target is ø10 mm ø0.39" pin gauge. The value is the edge in the Position mode after 16 times of the Smoothing. ^3 The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^4 With initial setting, minimum measuring range, and single smoothing processing ^*5 The illumination on the receiver of the sensor head when targeting an illuminated white paper.

Keyence LJ-S160 Keyence

€0,00

Sold Out

Specifications

Model			LJ-S160
Reference distance			211 mm 8.31"^*1
Measurement range	Z-axis (height)		±50 mm ±1.97" (F.S.=100 mm 3.94")
	X-axis (width)	NEAR side	124 mm 4.88"
		Reference distance	143 mm 5.63"
		FAR side	160 mm 6.30"
	Y-axis	Reference distance
XY data interval			50 μm 0.0020"
Number of XY data points			3200×3200
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		3 μm 0.000118"^*4
	XY (distance)		5 μm 0.000197"^*5
Linearity	Standard area		±0.02% of F.S.^*6
	High-accuracy area		—
Imaging time			Min. 0.3 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 5.5 A (at 19.2 V), 4.4 A (at 24 V)^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 3600 g 7.94 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-G015K Keyence

€11.575,95

Only 4 units left

Specifications

Model			LJ-G015K
Mounting			Specular reflective
Reference distance			15 mm 0.59"
Measuring range	Z-axis (Height)		±2.3 mm ±0.09"
	X-axis (Width)	Near	6.5 mm 0.26"
		Reference distance	7.0 mm 0.28"
		Far	7.5 mm 0.30"
Light source	Type		Red semiconductor laser
	Wavelength		655nm (Visible light), Class 2 laser product (JIS C6802)
	Output		0.95 mW
	Laser Class		Class II Laser Product (FDA (CDRH) 21CFR PART1040.10), Class 2 Laser Product (IEC 60825-1)
Spot shape (at reference distance)			Approx 32 µm x 12 mm 0.001260" x 0.47"
Repeatability	Z-axis (Height)		0.2 µm 0.000008"^*1
	X-axis (Width)		2.5 µm 0.000099"^*2
Linearity Z-axis (Height)			±0.1% of F.S.^*3
Sampling cycle (trigger interval)			3.8 ms^*4
Temperature characteristics			0.02% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529)
	Ambient light		Incandescent lamp or fluorescent lamp: 5,000 lux max.^*5
	Ambient temperature		0 to +50 °C 32 to 122 °F
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material			Aluminum
Weight			Approx. 260 g
^1 The value obtained after 64 times averaging at the reference distance.The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^2 The value obtained after 64 times averaging at the reference distance.The target is ø10 mm ø0.39" pin gauge. The value is the edge in the Position mode after 16 times of the Smoothing. ^3 The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^4 With initial setting, minimum measuring range, and single smoothing processing ^*5 The illumination on the receiver of the sensor head when targeting an illuminated white paper.

Keyence LJ-S080 Keyence

€0,00

Sold Out

Specifications

Model			LJ-S080
Reference distance			160 mm 6.30" ^*1
Measurement range	Z-axis (height)		±23 mm ±0.91" (F.S.=46 mm 1.81")
	X-axis (width)	NEAR side	66 mm 2.60"
		Reference distance	72 mm 2.83"
		FAR side	78 mm 3.07"
	Y-axis	Reference distance	160 mm 6.30"
XY data interval			25 μm 0.0010"
Number of XY data points			3200 × 6400
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		1 μm 0.000039" ^*4
	XY (distance)		3 μm 0.000118" ^*5
Linearity	Standard area		±0.055% of F.S. ^*6
	High-accuracy area		±0.03% of F.S. ^*6
Imaging time			Min. 0.2 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 4.0 A (at 19.2 V), 3.2 A (at 24 V) ^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 2600 g 5.73 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-G015 Keyence

€1.228,95

Only 6 units left

Specifications

Model			LJ-G015
Mounting			Diffuse reflective
Reference distance			15 mm 0.59"
Measuring range	Z-axis (Height)		±2.6 mm ±0.1"
	X-axis (Width)	Near	6.5 mm 0.26"
		Reference distance	7.0 mm 0.28"
		Far	7.5 mm 0.30"
Light source	Type		Red semiconductor laser
	Wavelength		655nm (Visible light), Class 2 laser product (JIS C6802)
	Output		0.95 mW
	Laser Class		Class II Laser Product (FDA (CDRH) 21CFR PART1040.10), Class 2 Laser Product (IEC 60825-1)
Spot shape (at reference distance)			Approx 32 µm x 12 mm 0.001260" x 0.47"
Repeatability	Z-axis (Height)		0.2 µm 0.000008"^*1
	X-axis (Width)		2.5 µm 0.000099"^*2
Linearity Z-axis (Height)			±0.1% of F.S.^*3
Sampling cycle (trigger interval)			3.8 ms^*4
Temperature characteristics			0.02% of F.S./°C
Environmental resistance	Enclosure rating		IP67 (IEC60529)
	Ambient light		Incandescent lamp or fluorescent lamp: 5,000 lux max.^*5
	Ambient temperature		0 to +50 °C 32 to 122 °F
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material			Aluminum
Weight			Approx. 260 g
^1 The value obtained after 64 times averaging at the reference distance.The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^2 The value obtained after 64 times averaging at the reference distance.The target is ø10 mm ø0.39" pin gauge. The value is the edge in the Position mode after 16 times of the Smoothing. ^3 The target is KEYENCE standard object. The value is the average of the widths in the Height mode. ^4 With initial setting, minimum measuring range, and single smoothing processing ^*5 The illumination on the receiver of the sensor head when targeting an illuminated white paper.

Keyence LJ-S040 Keyence

€33.115,95

Only 1 unit left

Specifications

Model			LJ-S040
Reference distance			70 mm 2.76" ^*1
Measurement range	Z-axis (height)		±18 mm ±0.71" (F.S.=36 mm 1.42")
	X-axis (width)	NEAR side	31 mm 1.22"
		Reference distance	35 mm 1.38"
		FAR side	39 mm 1.54"
	Y-axis	Reference distance	80 mm 3.15"
XY data interval			12.5 μm 0.0005"
Number of XY data points			3200 × 6400
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		0.5 μm 0.000020" ^*4
	XY (distance)		1 μm 0.000039" ^*5
Linearity	Standard area		±0.02% of F.S. ^*6
	High-accuracy area		—
Imaging time			Min. 0.2 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 4.0 A (at 19.2 V), 3.2 A (at 24 V) ^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 2600 g 5.73 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-G5001P Keyence

€5.727,95

Only 9 units left

Specifications

Model		LJ-G5001P
Head compatibility		Compatible
Number of connectable sensors		2 units max.
Display	Minimum display unit	0.1 µm ^*1, 0.001 mm₂, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)
	Maximum display range	±99999.9 mm, ±999999 mm₂, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)
Input terminal block	Laser remote interlock input	Non-voltage input
	Trigger input	For sensor head A, voltage input
	Timing 1 input	Voltage input
	Auto-zero 1 input
	Reset input
Output terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Total judgment output	PNP open-collector output
	Error output	PNP open-collector output (N.C.)
	Process output	PNP open-collector output
	Trigger input enable output	For sensor head A, PNP open-collector output
	Adjusted error output
Expansion connector	Timing 2 input	Voltage input
	Auto-zero 2 input
	Trigger input	For sensor head B, voltage input
	Program switching input	Voltage input, 4 inputs
	Memory card save input	Voltage input
	Laser-Off input	For sensor head A/B, voltage input
	Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) PNP open-collector output^*2
	Strobe output	PNP open-collector output
	Trigger input enable output	For sensor head B, PNP open-collector output
	Adjusted error output
Analog RGB monitor output		SVGA (800 x 600 pixels)
RS-232C interface		Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface		In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface		100BASE-TX/10BASE-T
Memory card		Compatible with NR-M1G (1 GB). (with FAT32)
Major functions		Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 1,050 g
^1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. ^2 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current)

Keyence LJ-S025 Keyence

€0,00

Sold Out

Specifications

Model			LJ-S025
Reference distance			68.5 mm 2.70" ^*1
Measurement range	Z-axis (height)		±9 mm ±0.35" (F.S.=18 mm 0.71")
	X-axis (width)	NEAR side	21 mm 0.83"
		Reference distance	23 mm 0.91"
		FAR side	25 mm 0.98"
	Y-axis	Reference distance	51.2 mm 2.02"
XY data interval			8 μm 0.000315"
Number of XY data points			3200 × 6400
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		0.4 μm 0.000016" ^*4
	XY (distance)		0.7 μm 0.000028" ^*5
Linearity	Standard area		±0.03% of F.S. ^*6
	High-accuracy area		—
Imaging time			Min. 0.2 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 4.0 A (at 19.2 V), 3.2 A (at 24 V) ^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 2100 g 4.63 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-G5001 Keyence

€2.876,95

Only 9 units left

Specifications

Model		LJ-G5001
Head compatibility		Measuring units are interchangeable without factory recalibration.
Number of connectable sensors		Maximum of 2 units
Display	Minimum display unit	0.1 µm ^*1, 0.001 mm₂, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)
	Maximum display range	±99999.9 mm, ±999999 mm₂, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)
Input terminal block	Laser remote interlock input	Non-voltage or voltage input ^*2.
	Trigger input	For sensor head A, non-voltage input
	Timing 1 input	Non-voltage input
	Auto-zero 1 input
	Reset input
Output terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Total judgment output	NPN open-collector output
	Error output	NPN open-collector output (N.C.)
	Process output	NPN open-collector output
	Trigger input enable output	For sensor head A, NPN open-collector output
	Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
	Auto-zero 2 input
	Trigger input	For sensor head B, non-voltage input
	Program switching input	Non-voltage input, 4 inputs
	Memory card save input	Non-voltage input
	Laser-Off input	For sensor head A/B, non-voltage input
	Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output^*3
	Strobe output	NPN open-collector output
	Trigger input enable output	For sensor head B, NPN open-collector output
	Adjusted error output
Analog RGB monitor output		SVGA (800 × 600 pixels)
RS-232C interface		Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface		Supports USB 2.0 Hi-Speed (compatible with USB 1.1 Full Speed)
Ethernet interface		100BASE-TX/10BASE-T^*4
Memory card		Compatible with NR-M1G (1 GB). (with FAT32)
Major functions		Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 1,050 g
^1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. ^2 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^3 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current) ^4 This is dedicated for connection with IV-series sensor.

Keyence LJ-S015 Keyence

€0,00

Sold Out

Specifications

Model			LJ-S015
Reference distance			56.5 mm 2.22" ^*1
Measurement range	Z-axis (height)		±4 mm ±0.16" (F.S.=8 mm 0.31")
	X-axis (width)	NEAR side	14 mm 0.55"
		Reference distance	15 mm 0.59"
		FAR side	16 mm 0.63"
	Y-axis	Reference distance	25 mm 0.98"
XY data interval			5 μm 0.000197"
Number of XY data points			3200 × 5000
Light source	Laser light source		405 nm (visible light) wavelength blue semiconductor laser
	Laser class		Class 2M laser product^2 (IEC 60825-1, FDA (CDRH) Part 1040.10^3)
	Output		10 mW
Repeatability	Z-axis (height)		0.3 μm 0.000012" ^*4
	XY (distance)		0.5 μm 0.000020" ^*5
Linearity	Standard area		±0.035% of F.S. ^*6
	High-accuracy area		—
Imaging time			Min. 0.2 sec ^*7
I/F	Ethernet		1000BASE-T, 100BASE-TX
	Input		LASER_ON, TRG, MEM_CLEAR ^*8
	Output		READY, EXPOSURE_BUSY, ERROR ^*8
Ratings	Power voltage		24 VDC +25%, -20%
	Current consumption / Power		Max. 4.0 A (at 19.2 V), 3.2 A (at 24 V) ^*9 / Typ. 17 W
Environmental resistance	Enclosure rating		IP65 (IEC60529) ^*10
	Ambient light		Incandescent lamp: 10000 lux or less ^*11
	Ambient temperature		0 to +45°C 32.0°F to +113.0°F ^*12
	Relative humidity		85% RH or below (no condensation)
	Vibration resistance		10 to 500 Hz; Power spectral density: 0.033 G2/Hz; X, Y, and Z directions (IEC 60068-2-64)
	Shock resistance		15 G (IEC 60068-2-27)
Material			Aluminum
Weight			Approx. 2300 g 5.07 lb
^1 The reference distance is the distance from the bottom edge of the head to the measurement center of the Z-axis (height). See the Dimensions section for the installation reference plane. ^2 Do not view the beam directly using optical instruments (such as eye loupes, magnifiers, microscopes, telescopes, or binoculars). Observing the laser output using optical instruments is dangerous and may damage the eyes. ^3 Laser classification performed based on IEC60825-1 in accordance with FDA (CDRH) Laser Notice. ^4 The measured target is a KEYENCE standard target. Sigma value when the average height of 200 × 200 points in the center of the field of view is measured using the height tool with reciprocating imaging OFF. ^5 The measured target is a KEYENCE standard target. Sigma value when the distance between two circles of 500 points in diameter set 1000 points apart at the center of the field of view on a grayscale image is measured using the circle and circle distance tool with reciprocating imaging OFF. ^6 The measured target is a KEYENCE standard target. Value when the average height of 200 × 200 points is measured using the height tool with reciprocating imaging OFF. See the Dimensions section for the high-accuracy area reference plane. ^7 With YZ range minimum and Y skipping maximum. ^8 Laser ON input is enabled only when connected to a controller. ^9 The maximum value may be exceeded when extreme acceleration is applied. ^10 With an OP cable connected. ^11 When measuring white paper, illuminance on the sensor head receiving surface when light is applied to white paper. ^12 The head needs to be mounted to a metal plate to be used.

Keyence LJ-S8002 Keyence

€0,00

Sold Out

Specifications

Model		LJ-S8002
Head input		Up to two LJ-S8000 Series head units * When using two units, heads A and B must be the same model.
Number of registered inspection settings		Up to 1000 settings (depending on SD card capacity and setting contents) for each of SD card 1 and SD card 2; External switching possible
Master profile / number of reference images		Up to 400 per setting (depending on SD card capacity)
Memory card		• SD card slot × 2 • Supports OP-87133 (512 MB), CA-SD1G (1 GB), CA-SD4G (4 GB; Equipped as standard for SD1 slot), and CA-SD16G (16 GB)
Number of tools		Up to 100 per setting
Interface	Control input	20 points (Input terminal block: 5 points, Parallel I/O: 15 points)
	Control output	• 28 points (Output terminal block: 6 points, Parallel I/O: 22 points) • Photo MOSFET^*1
	RS-232C	• Numerical value output and control I/O (When in use, PLC Link using the RS-232C port cannot be used) • Supports baud rates of up to 230400 bps
	PLC link	• Numerical value output and control I/O using Ethernet or RS-232C ports (Cannot be used with EtherNet/IP™; When using an RS-232C port, cannot be used with RS-232C no-procedure communication)
	Ethernet	• Numerical value output and control I/O • In addition to the functions above, uploading/downloading inspection settings, performing various simulations, and sending/receiving images and other data, and using remote desktop connections are possible via KEYENCE PC application software. • Supports FTP client, FTP server, VNC server (for non-PC clients, only monitor screen display is supported), and BOOTP functions supported • 1000BASE-T/100BASE-TX/10BASE-T • Supports jumbo frames
	USB	• In addition to numerical value output, uploading/downloading inspection settings, performing various simulations, and sending/receiving images and other data, and using remote desktop connections are possible via KEYENCE PC application software. • USB 2.0 only
	EtherNet/IP^TM	• Numerical value I/O and control I/O using the Ethernet port or optional EtherNet/IP™ unit CB-NEP20E (Cannot be used with PLC Link, PROFINET, or EtherCAT®) • Supports cyclic communication (max. 1436 bytes) and message communication • Maximum number of connections: 32 (Ethernet port) / 1: Exclusive Owner, 4: Input Only (CB-NEP20E) • Complies with Version CT19.1 (Ethernet port) / CT19.1 (CB-NEP20E) conformance tests
	PROFINET	• Can input/output numerical values and perform control I/O using the Ethernet port or the optional PROFINET unit CB-NPN20EA (Cannot be used with PLC Link, EtherNet/IP™, and EtherCAT®) • Supports cyclic communication (max. 1408 bytes) (Ethernet port) / 1252 bytes (CB-NPN20EA) • Supports acyclic communication (recorded data) • Complies with Conformance Class A (Ethernet port) / C (CB-NPN20EA)
	EtherCAT^®	• Numerical value output and control I/O using optional EtherCAT® unit CB-NEC20E (Cannot be used with PLC Link, EtherNet/IP™, or PROFINET) • Supports cyclic communication (process data object communication) (Input: Max. 536 bytes / Output: Max. 532 bytes) • Supports acyclic communication (mailbox communication) • Supports CoE • Explicit device identification • Complies with Version 2.5.0 conformance test
	Mouse	Various menus can be controlled using the dedicated mouse (included with the controller)
	SNTP	Automatic correction of controller date and time when connected to an SNTP server
	USB HDD	Images and other data can be output by connecting an HDD (2 TB max.) to the dedicated USB port (USB 3.0-compliant, bus-powered, rated output: 900 mA)
	Monitor output	Analog RGB output, XGA 1024 × 768 (24-bit color, 60 Hz)
Cooling fan		Available
Language		Switchable between English, Japanese, and Chinese (Simplified)
Ratings	Power voltage	24 VDC ±10%
	Maximum current consumption	Max. 2.5 A (Typ. 28 W)
Environmental resistance	Ambient temperature	0 to 45°C 32.0°F to 113.0°F (DIN rail mounting) / 0 to 40°C 32.0°F to 104.0°F (Base surface mounting)
	Relative humidity	85% RH or less (no condensation)
Weight		Approx. 2200 g 4.85 lb
^*1 Positive common connection for NPN input devices and negative common connection for PNP input devices supported.