LJ-G5001 Keyence

Specifications

Model		LJ-G5001
Head compatibility		Measuring units are interchangeable without factory recalibration.
Number of connectable sensors		Maximum of 2 units
Display	Minimum display unit	0.1 µm ^*1, 0.001 mm₂, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)
	Maximum display range	±99999.9 mm, ±999999 mm₂, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)
Input terminal block	Laser remote interlock input	Non-voltage or voltage input ^*2.
	Trigger input	For sensor head A, non-voltage input
	Timing 1 input	Non-voltage input
	Auto-zero 1 input
	Reset input
Output terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Total judgment output	NPN open-collector output
	Error output	NPN open-collector output (N.C.)
	Process output	NPN open-collector output
	Trigger input enable output	For sensor head A, NPN open-collector output
	Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
	Auto-zero 2 input
	Trigger input	For sensor head B, non-voltage input
	Program switching input	Non-voltage input, 4 inputs
	Memory card save input	Non-voltage input
	Laser-Off input	For sensor head A/B, non-voltage input
	Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output^*3
	Strobe output	NPN open-collector output
	Trigger input enable output	For sensor head B, NPN open-collector output
	Adjusted error output
Analog RGB monitor output		SVGA (800 × 600 pixels)
RS-232C interface		Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface		Supports USB 2.0 Hi-Speed (compatible with USB 1.1 Full Speed)
Ethernet interface		100BASE-TX/10BASE-T^*4
Memory card		Compatible with NR-M1G (1 GB). (with FAT32)
Major functions		Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 1,050 g
^1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. ^2 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^3 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current) ^4 This is dedicated for connection with IV-series sensor.

Est. delivery between and

€2.876,95

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: LJ-G5001-Sealed

Sold out

€0,00

Never Used Surplus

SKU: LJ-G5001

5 verified stock

€2.876,95

Used

SKU: LJ-G5001-Used

4 verified stock

€847,95

Variant

Quantity:

Need More?

Specifications

Model		LJ-G5001
Head compatibility		Measuring units are interchangeable without factory recalibration.
Number of connectable sensors		Maximum of 2 units
Display	Minimum display unit	0.1 µm ^*1, 0.001 mm₂, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)
	Maximum display range	±99999.9 mm, ±999999 mm₂, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)
Input terminal block	Laser remote interlock input	Non-voltage or voltage input ^*2.
	Trigger input	For sensor head A, non-voltage input
	Timing 1 input	Non-voltage input
	Auto-zero 1 input
	Reset input
Output terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Total judgment output	NPN open-collector output
	Error output	NPN open-collector output (N.C.)
	Process output	NPN open-collector output
	Trigger input enable output	For sensor head A, NPN open-collector output
	Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
	Auto-zero 2 input
	Trigger input	For sensor head B, non-voltage input
	Program switching input	Non-voltage input, 4 inputs
	Memory card save input	Non-voltage input
	Laser-Off input	For sensor head A/B, non-voltage input
	Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output^*3
	Strobe output	NPN open-collector output
	Trigger input enable output	For sensor head B, NPN open-collector output
	Adjusted error output
Analog RGB monitor output		SVGA (800 × 600 pixels)
RS-232C interface		Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface		Supports USB 2.0 Hi-Speed (compatible with USB 1.1 Full Speed)
Ethernet interface		100BASE-TX/10BASE-T^*4
Memory card		Compatible with NR-M1G (1 GB). (with FAT32)
Major functions		Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 1,050 g
^1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. ^2 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^3 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current) ^4 This is dedicated for connection with IV-series sensor.

Model		LJ-G5001
Head compatibility		Measuring units are interchangeable without factory recalibration.
Number of connectable sensors		Maximum of 2 units
Display	Minimum display unit	0.1 µm ^*1, 0.001 mm₂, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)
	Maximum display range	±99999.9 mm, ±999999 mm₂, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)
Input terminal block	Laser remote interlock input	Non-voltage or voltage input ^*2.
	Trigger input	For sensor head A, non-voltage input
	Timing 1 input	Non-voltage input
	Auto-zero 1 input
	Reset input
Output terminal block	Analog voltage output	±10 V x 2 outputs, output impedance: 100 Ω
	Total judgment output	NPN open-collector output
	Error output	NPN open-collector output (N.C.)
	Process output	NPN open-collector output
	Trigger input enable output	For sensor head A, NPN open-collector output
	Adjusted error output
Expansion connector	Timing 2 input	Non-voltage input
	Auto-zero 2 input
	Trigger input	For sensor head B, non-voltage input
	Program switching input	Non-voltage input, 4 inputs
	Memory card save input	Non-voltage input
	Laser-Off input	For sensor head A/B, non-voltage input
	Judgment/Binary output	3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output^*3
	Strobe output	NPN open-collector output
	Trigger input enable output	For sensor head B, NPN open-collector output
	Adjusted error output
Analog RGB monitor output		SVGA (800 × 600 pixels)
RS-232C interface		Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface		Supports USB 2.0 Hi-Speed (compatible with USB 1.1 Full Speed)
Ethernet interface		100BASE-TX/10BASE-T^*4
Memory card		Compatible with NR-M1G (1 GB). (with FAT32)
Major functions		Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.
Rating	Power voltage	24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	800 mA or less with 1 sensor head/1 A or less with two sensor heads
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 1,050 g
^1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm. ^2 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^3 Time-sharing output of judgment results or binary measured data. The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current) The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less OFF current) ^4 This is dedicated for connection with IV-series sensor.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator