Machine Vision Systems

€377,95

Only 5 units left

Specifications

Model		PR-G51CBD
Type		Thrubeam
Shape		Threaded mount type
Output		NPN+PNP
Cable connection		M12 connector (4 pin)
Detecting distance		30 m 98.43'
Number of control outputs		2 (NPN+PNP)
Output operation	Output 1	Dark-ON
	Output 2	Light-ON^*1
Response time		1 ms
Sensitivity adjustment		One-turn trimmer (230°)
Spot diameter		―
Light source		4 elements, Red LED (631 nm)
Light interference prevention function		―
Indicator lamp		Transmitter: power supply indicator (green) Receiver: output indicator (yellow), Stable operation indicator (green)
Control output		NPN + PNP open collector 30 VDC or less, 100 mA or less Residual voltage: 1.2 V or less at less than 10 mA, 2 V or less at 10 to 100 mA
Stop emission input		Non-voltage input Input time ON: 1 ms or more, OFF: 20 ms or more
Protection circuit		Protection against reverse power connection, power supply surge, output overcurrent, output surge, and reverse output connection
Rating	Power voltage	10 to 30 VDC, including Ripple (P-P) 10 %
	Power consumption	Transmitter: 450 mW max. (15 mA max. at 24 V, 15 mA max. at 12 V) Receiver: 360 mW max. (12 mA max. at 24 V, 15 mA max. at 12 V)
Environmental resistance	Enclosure rating	IP68 (IEC60529), IP69K (DIN40050-9), 4, 6, 13 (NEMA250)^*2
	Insulation resistance	20 MΩ or more (500 VDC)
	Ambient light	Incandescent lamp: 5,000 lux or less, Sunlight: 20,000 lux or less
	Ambient temperature	-20 to +70 °C -4 to 158 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-20 to +70 °C -4 to 158 °F
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Accessories		Instruction Manual, M18 nut, Lock washer
Weight		Approx. 85 g
^1 Output 2 is not available on the threaded mount type or M8 3-pin type. ^2 For the connector type, the enclosure rating varies depending on the cable that is used. ^*3 When the ambient temperature is 60 °C 140 °F or higher, the device should be powered with no more than 24 VDC and 50 mA.

Keyence FD-XC8R1 Keyence

€642,95

Only 5 units left

Specifications

Model				FD-XC8R1
Supported diameter				Outer diameter of pipe: ø 6 0.24 " Attachable range: ø 5.5 to 6.5 0.22 " to 0.26 "
Weight				Approx. 55 g

Keyence FR-SB31A Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GS-Y11 Keyence

€916,95

Only 2 units left

Specifications

Model				GS-Y11
Weight				Approx.50 g 1.76 oz

Keyence SJ-E252L Keyence

€0,00

Sold Out

Specifications

Model		SJ-E252L
Ion generation method		Corona discharge method
Structure		Shockless resistive coupling type
Voltage application method / Applied voltage		Pulse AC method/±8000 V
Ion balance control method		Hi-Power I.C.C. method
Ion balance		±30 V^*1
Installation distance		50 to 2000 mm 1.97" to 78.74"
Control input	Static elimination stop input	NPN open collector or contact point signal without voltage
Control output	Ion level warning, condition warning, alarm output	NPN open collector, Maximum 100 mA (40 VDC or less)
	Condition alarm output
	Alarm output
Communication function		Remote control communication
Major functions		Condition alarm, ion level alarm, alarm output
Air connection port		Rc 1/8
Air supply pressure		0.1 MPa to 0.5 MPa^*2 (recommended air pressure of 0.2 MPa)
Effective length		2600 mm 102.36"^*3
Total length		2480 mm 97.64"
No. ofelectrodes		41
Rating	Power voltage	24 VDC to 36 VDC ±10%
	Current consumption	700 mA (at 24 V), 500 mA (at 36 V)
	Overvoltage category	I
	Pollution degree	2
Environmental resistance	Ambient temperature	0 to +40°C 32 to 104°F
	Relative humidity	35 to 85% RH (no condensation)
Material	Electrode probe	Tungsten
	Main body	ABS/PBT/PP/LCP/PPS/SPS/SUS
Weight		2500 g 88.19oz
^1 Measured under the following conditions. Installation distance: 300 mm 11.81" or more, Air supply pressure: 0.2 Mpa, Frequency: The highest device driving frequency, Operating ambient temperature: 0 to +40°C 32 to 104°F, Operating ambient humidity: 35 to 65% RH ^2 Contact KEYENCE when using the air purge function with intermittent air supply. ^*3 Effective length is for static elimination range when installation distance is 50 mm 1.97".

Keyence FD-MH50A Keyence

€714,95

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-42143 Keyence

€0,00

Sold Out

Specifications

Model				OP-42143
Type				CPU Direct Connection Cable
Applicable product				KV-D30
Length				5 m 16.40'

Keyence GL-R16L Keyence

€1.510,95

Only 6 units left

Specifications

Model			GL-R16L
Detection capability			ø1.77" ø45 mm
Total length			25.20" 640mm
No. of beam			16
Detection height			23.62" 600mm
Protection height			26.97" 685mm
Beam axis spacing/Lens diameter			40 mm / ø5 1.57" / ø0.20"
Detecting distance			0.66 to 49.21' 0.2 to 15 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	6.6
		OFF→ON	48.7^*2
		All blocked→ON	63.1^*3
	Optical synchronization system (Channel A or B)	ON→OFF	8.1
		OFF→ON	50.9^*2
		All blocked→ON	69.1^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	50
		Receiver	72
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		880 g
	Receiver		890 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence MD-F3220 Keyence

€0,00

Sold Out

Specifications

Model		MD-F3220
Type		Marking unit (Controller + Head) 30 W, Wide area
Console (sold separately)		MC-P1
Marking method		XYZ 3-axis simultaneous scanning method
Marking laser	Type	Yb: Fiber laser (Class 4 laser product; IEC/EN60825-1, JIS C6802, FDA (CDRH) Part 1040.10^*1, GB7247.1)
	Wavelength	1090 nm
	Output	30 W
Applicable regulations		EU directive (EMC directive, machinery directive, RoHS directive), EN standard (EN 55011, EN ISO 11553-1, EN 60204-1, EN 60825-1, EN 61000-6-2, EN 50581), CSA and UL standards (CAN/CSA C22.2 No. 61010-1-12, UL 61010-1), North America regulations (FCC Part 15B, ICES-001 Class A), China RoHS
Pulse frequency		60 to 120 kHz
Guide laser/Working distance pointer		Semiconductor laser, Wavelength: 655 nm, Output: 1.0 mW (Class 2 laser product; IEC/EN60825-1, JIS C6802, FDA (CDRH) Part 1040.10^*1, GB7247.1)
Marking area		300 × 300 × 42 mm 11.81" × 11.81" × 1.65"
Standard working distance (±variable width)		300 mm (±21 mm) 11.81" (±0.83")
Marking resolution		5 µm 0.20 Mil
Scan speed		Max. 8000 mm/s 314.96"/s
Character type	Font	KEYENCE original font (numbers, letters, katakana, hiragana, kanji), User fonts, True Type fonts
	Barcode	CODE39, ITF, 2of5, NW7 (CODABAR), JAN, CODE128, EAN, UPC-A, UPC-E, CODE93
	2D code	QR code, Micro QR code/DataMatrix (ECC200/GS1 DataMatrix)
	GS1 DataBar	GS1 DataBar, GS1 DataBar CC-A, GS1 DataBar Stacked, GS1 DataBar Stacked CC-A, GS1 DataBar Limited, GS1 DataBar Limited CC-A, GS1 DataBar Truncated, GS1 DataBar Truncated CC-A
	Logo image	Custom character font and logo CAD data, BMP/JPEG/PNG/TIFF
Marking conditions	Workpiece style	Stationary/moving marking (constant speed/encoder)
	Character size (marking height/width)	0.1 to 300 mm 0.004" to 11.81"
	No. of registered programs	Max. 2000 programs
	No. of program blocks	256 blocks
I/O (Input/output)		Terminal block I/O, MIL connector I/O
Interface		RS-232C, USB 2.0, Ethernet (100BASE-TX/10BASE-T)^*2
Head installation direction		All directions
Head cable length		4.0 m 13.1'
Cooling method		Controller: Forced air cooling, Head: Natural air cooling
Rated voltage and power consumption		100 to 120 VAC or 200 to 240 VAC ± 10 %, 50/60 Hz, Max. 550 VA
Environmental resistance	Enclosure rating	IP64 (Head)
	Pollution degree	2
	Overvoltage category	II
	Ambient temperature for storage	-10 to +60 °C 14 to 140 °F (No freezing)
	Ambient temperature	0 to +40 °C 32 to 104 °F
	Ambient humidity for storage	30 to 85 % RH (No condensation)
	Relative humidity
Weight		Controller: 24.4 kg Head: 6.7 kg Console: 2.0 kg
^1 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^2 The USB port is designed for use with USB memory sticks, barcode readers, mouses (A connector), and Marking Builder 3 (ActiveX) (B connector). The Ethernet port supports communication with Marking Builder 3 (ActiveX), TCP/IP communication, PROFINET connection, and EtherNet/IP™ connection.

Keyence CA-DLR7 Keyence

€819,95

Only 5 units left

Specifications

Model				CA-DLR7
Type				Low Angle Light
LED color				Red
Power consumption				2 W
Input voltage				12 VDC
Weight				Approx. 40 g

Keyence FKV-B16R Keyence

€608,95

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GL-VM127FP Keyence

€1.853,95

Only 10 units left

Specifications

Model			GL-VM127FP
Beam axis spacing/Lens diameter			10 mm 0.39": ø4 ø0.16"
Number of beam axes			127
Total length			1280 mm 50.39"
Detection height			1260 mm 49.61"
Protection height			1284 mm 50.55"
Minimum detectable object size			ø14 mm ø0.55" ^*1
Detecting distance			0.3 to 12 m 1.0' to 39.4' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	9.2
		OFF→ON	54.9 ^*3
		All blocked→ON	68.0 ^*4
	With channel A or B	ON→OFF	30.3
		OFF→ON	86.5 ^*3
		All blocked→ON	130.2 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	146 ^*5
		Receiver	163 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	64 ^*5
		Receiver	71 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		840 g 29.65 oz
	Receiver		850 g 30.00 oz
	Total		1690 g 59.65 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence GL-R96H Keyence

€1.792,95

Only 9 units left

Specifications

Model			GL-R96H
Detection capability			ø0.98" ø25 mm
Total length			75.59" 1920mm
No. of beam			96
Detection height			74.80" 1900mm
Protection height			76.57" 1945mm
Beam axis spacing/Lens diameter			20 mm / ø5 0.79" / ø0.20"
Detecting distance			0.66 to 49.21' 0.2 to 15 m^*1
Effective aperture angle			Max. ±2.5° (When operating distance is 9.84' 3 m or more)
Light source			Infrared LED (870 nm)
Response time (OSSD) (ms)	Wire synchronization, One-line or Optical synchronization system (Channel 0)	ON→OFF	14.8
		OFF→ON	61^*2
		All blocked→ON	96^*3
	Optical synchronization system (Channel A or B)	ON→OFF	22
		OFF→ON	71.8^*2
		All blocked→ON	124.8^*3
Detection mode			Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver			Optical synchronization or Wire synchronization (Determined by wiring)
Light interference prevention function			Prevents mutual interference in up to two GL-R systems. Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output		2 transistor outputs. (PNP or NPN is determined by the cable type)
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 16.40' 5 m)
	OFF state voltage		Max. 2.0 V (with a cable length of 16.40' 5 m)
	Leakage current		Max. 200 µA
	Max. capacitive load		2.2 µF
	Load wiring resistance		Max. 2.5 Ω
Supplemental output (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of 16.40' 5 m)
	Error output
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	When using a PNP output cable	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V OFF voltage: Open or 0 to 3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	Power voltage		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption (Max.) (mA)	Transmitter	81
		Receiver	91
Protection circuit			Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety		IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1:2015 (Category 4, PLe) UL508 UL1998
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Overvoltage category		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		15 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum
	Upper case/lower case		Nylon (GF 30%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		2680 g
	Receiver		2690 g
^1 When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by 1.64' 0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by 3.28' 1.0 m. ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4 When the GL-R is used under surrounding air temperatures between 50 to 55°C 122°F to 131°F, the Maximum load current should not exceed 350 mA.

Keyence OP-88962 Keyence

€0,00

Sold Out

Specifications

Model				OP-88962
Length				2 m 6.6'

Keyence OP-88045 Keyence

€394,95

Only 2 units left

Specifications

Model				OP-88045
Length				10 m 32.81'
Note				This cable is used for connecting between sensor and PC or Ethernet switch. When using IV Series as UL approved product, use Ethernet cable supporting NFPA79.

Keyence CA-HS035CH Keyence

€0,00

Sold Out

Specifications

Model		CA-HS035CH
Image element		Color CMOS, 7× high-speed reading using square-pixel
Unit cell size		7.4 µm × 7.4 µm 0.29 Mil × 0.29 Mil
Valid pixel count		0.31 megapixel mode: 640 (H) × 480 (V), 0.24 megapixel mode: 512 (H) × 480 (V)
Image size		Equivalent to 1/3"
Scanning system		Progressive 4.5 ms
Pixel transfer frequency		86 MHz (43 MHz × 2)
Transfer system		Digital serial transfer
Electronic shutter		Can be set to 0.05 to 100 msec by specifying the following numerical inputs: 1/15, 1/30, 1/60, 1/120, 1/240, 1/500, 1/1000, 1/2000, 1/5000, 1/10000, 1/20000
Lens mount		Special mount (M10.5 P0.5 male)
Environmental resistance	Ambient temperature	0 to 40°C 32 to 104°F
	Relative humidity	85% RH or less
Weight		Approx. 135 g (cable included, lens not included)

Keyence CV-H1X Keyence

€394,95

Only 10 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence LS-9500 Keyence

€4.444,95

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CV-2600 Keyence

€6.502,95

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GL-VM47FP Keyence

€790,95

Only 9 units left

Specifications

Model			GL-VM47FP
Beam axis spacing/Lens diameter			10 mm 0.39": ø4 ø0.16"
Number of beam axes			47
Total length			480 mm 18.90"
Detection height			460 mm 18.11"
Protection height			484 mm 19.06"
Minimum detectable object size			ø14 mm ø0.55" ^*1
Detecting distance			0.3 to 12 m 1.0' to 39.4' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	5.8
		OFF→ON	48.2 ^*3
		All blocked→ON	56.2 ^*4
	With channel A or B	ON→OFF	16.9
		OFF→ON	69.1 ^*3
		All blocked→ON	92.7 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	86 ^*5
		Receiver	96 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	57 ^*5
		Receiver	61 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		320 g 11.29 oz
	Receiver
	Total		640 g 22.59 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence CA-CN5R Keyence

€983,95

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CA-DBW5 Keyence

€225,95

Only 9 units left

Specifications

Model				CA-DBW5
Type				Bar Light
LED color				White
Diffusion plate				OP-42283
Polarizing plate				OP-42281
Power consumption				2.9 W
Input voltage				12 VDC
Weight				Approx. 40 g

Keyence SV3-M100AS Keyence

€0,00

Sold Out

Specifications

Model				SV3-M100AS
General specifications	Applicable servo amplifier			SV3-100L2
	Rated output			0.85k W
	Rated torque			5.39 N·m ^*1
	Instant maximum torque			14.2 N·m
	Rated current			6.9 Arms
	Instant maximum current			17 Arms
	Rated rotation speed			1,500 min^-1
	High rotation speed			4,000 min^-1
	Torque constant			0.859 N·m/Arms
	Rotor moment of inertia			13.9 ×10^-4 kg·m²
	Rated power rating			20.9 kW/s
	Rated angle acceleration			3,880 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4 ft/s² (forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			Class F
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			5×^*2
	Approx. weight			5.5 kg 12.13 lb
^1 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^2 This is the value at 3,000 min-1. At 4,000 min-1, 1 kW becomes 2×, 1.5 kW becomes 2×, 3 kW (with the SV3-300L2 connected) becomes 2.2×, 3 kW (with the SV3-500L2 connected) becomes 4×, and 5 kW becomes 2.4×.

Keyence OP-89081 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.