Machine Vision Systems

€640,95

Only 6 units left

Specifications

Model		CZ-V21
Output		NPN output
Main unit/expansion unit		Main unit
Response time		8 ms (SUPER) /4 ms (TURBO) /1 ms (FINE) /200 µs (HIGH SPEED)
Control output		NPN open-collector x 4 channels, 40 VDC max., Up to 100 mA for one output, Up to 200 mA in total of 4 outputs, Residual voltage: 1.0 V max.^*1
Protection circuit		Reverse-polarity protection, overcurrent protection, surge absorber
External calibration input		No-voltage input, input time: 20 ms or more
External shift input
Timer function		Timer OFF/OFF-delay/ON-delay/One-shot, Timer time: 1 to 1000 ms adjustable (for each bank respectively)
Unit expansion		Up to 3 units (4 units total including the main unit)^*2
Rating	Power voltage	24 VDC, Ripple (P-P) 10 % or less
	Power consumption	Normal mode: 1.5 W (62.5 mA or less), Eco-mode: 1 W (42.0 mA or less)
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*3
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material		Housing, cover: Polycarbonate
Weight		Approx. 110 g
^1 20 mA max. when several units are connected. ^2 The FS-V20 Series expansion unit cannot be connected to the CZ-V20 Series main unit. When using a combination of expansion units, connect the CZ-V20 Series expansion unit to the FS-V20 Series main unit. Also, if using multiple expansion units, make sure to connect the CZ-V20 Series to right side of the FS-V20 Series. ^*3 When several units are connected, the acceptable ambient temperature varies depending on the conditions given below. To connect several units, be sure to mount them to a DIN rail and to limit the output current to a maximum of 20 mA. When 1 or 2 units are connected: -10 to +50 °C 14 to 122 °F When 3 units are connected: -10 to +45 °C 14 to 113 °F

Keyence OP-51455 Keyence

€0,00

Sold Out

Specifications

Model				OP-51455
Overview				Front protective cover protecting detection side of light curtain.
Applicable product				SL-V23F, SL-V12H, SL-V06L, SL-C12H
Number included				1 pcs.
Length				230.3 mm 9.07"
Material				Translucent plastic: Polycarbonate (t=Approx. 1.6mm), Black plastic: ABS
Note				To install this product on both the transmitter and receiver, 2 sets are required. Use the dimming filters (sold separately) by attaching them to the front protection cover. When the front protection cover is attached, the L-shaped mounting bracket (OP-42

Keyence FS-T1P Keyence

€158,95

In stock, 12 units

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence LX2-13 Keyence

€2.710,95

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence PR-F51C3PL Keyence

€368,95

Only 5 units left

Specifications

Model		PR-F51C3PL^*1
Type		Thrubeam
Output		PNP
Shape		Flat
Cable connection		M8 connector (3 pin)
Detection distance		0.6 m
Number of control outputs		1 output
Output operation	Output 1	-
	Output 2	Light-ON
Response time	Output 1	-
	Output 2	ON→OFF: 2.7 ms, OFF→ON: 0.5 ms
Sensitivity adjustment		None
Spot diameter		-
Light source		4 element, point light source, red LED (650 nm)
Mutual interference prevention function		-
Indicator lamp		Output indicator (orange), stable operation indicator (green), thrubeam type transmitter: power supply indicator (green)
Control output		30 VDC or lower, 50 mA or lower Leakage current: When 3 kΩ load resistance, 0.3 mA or lower. When 1 kΩ load resistance, 0.5 mA or lower. When 0.2 kΩ load resistance, 1.5 mA or lower Residual voltage: When 10 mA or lower, 1.0 V or lower. When 10 to 30 mA, 1.5 V or lower. When 30 to 50 mA, 2.0 V or lower.
Protection circuit		Power supply reverse connection protection, output overcurrent protection, output surge protection, power supply surge protection
Rating	Power voltage	10 to 30 VDC, including 10 % ripple (P-P)
	Current consumption	Transmitter: 11 mA, Receiver: 16 mA
Environmental resistance	Enclosure rating	IP67 (IEC60529), 4X, 6P, 13 (NEMA250)
	Insulation resistance	20 MΩ or higher (500 VDC)
	Ambient light	Incandescent lamp: 5,000 lux or lower, Sunlight: 20,000 lux or lower
	Ambient temperature	-25 to +55 °C -13 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-25 to +75 °C -13 to 167 °F
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: SUS316L, indicator cover/lens cover: polysulfone, cord protector: polymethylpentene, filler: polyester-based resin
Accessories		Instruction Manual
Weight		Approx. 20 g
^*1 The M8 connector (3 pin) type has 1 control output. If "D" is at the end of the part number, the sensor is equipped with a Dark-ON output. If "L" is at the end of the part number, the sensor is equipped with a Light-ON output. Example: The PR-M51C3PL has a Light-ON output.

Keyence FU-66Z Keyence

€119,95

Only 7 units left

Specifications

Model		FU-66Z^*1
Size		M4
Detection arrangement		Parallel
Fibre unit length		2 m78.74" free-cut
Fibre unit diameter		ø1.3×2
Shape		Straight
Minimum bend radius		R2 mm0.079" Tough-Flex
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 10 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence GL-VM08HN Keyence

€0,00

Sold Out

Specifications

Model			GL-VM08HN
Beam axis spacing/Lens diameter			20 mm 0.79": ø5 ø0.197"
Number of beam axes			8
Total length			160 mm 6.30"
Detection height			140 mm 5.51"
Protection height			185 mm 7.28"
Minimum detectable object size			ø25 mm ø0.98" ^*1
Detecting distance			0.3 to 15 m 1.0' to 49.2' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	4.1
		OFF→ON	45.7 ^*3
		All blocked→ON	51.2 ^*4
	With channel A or B	ON→OFF	10.3
		OFF→ON	57.1 ^*3
		All blocked→ON	70.8 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	56 ^*5
		Receiver	68 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	49 ^*5
		Receiver	56 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		120 g 4.23 oz
	Receiver
	Total		240 g 8.47 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence IV4-G600MA Keyence

€4.015,95

Only 1 unit left

Specifications

Model		IV4-G600MA
Type		Wide field of view model
Installed distance		From 50 mm 1.97"
Field of view		Installation distance 50 mm 1.97": 51 (H) × 38 (V) mm to Installation distance 3000 mm 118.11": 2730 (H) × 2044 (V) mm (reference value)
Image receiving element	Type	1/2.9 inch monochrome CMOS
	Number of pixels	1280 (H) × 960 (V)
Focus adjustment		Auto ^*1
Exposure time		12 μs to 9 ms ^2 ^3
Lights	Illumination	Infrared LED
	Lighting method	Pulse lighting
Indicators		2 indicators (both displaying same content)
Power supply	Average power consumption	2.5 W (without AI imaging illumination unit installed) 6.6 W (with AI imaging illumination unit installed)
Environmental resistance	Enclosure rating	IP67 ^*4
	Ambient temperature	0 to +50°C 32 to +122°F (no freezing) ^*5
	Relative humidity	85% RH or less (no condensation)
	Vibration resistance	Frequency: 10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y and Z directions
	Shock resistance	500 m/s² 1640.4 ft/s² 3 times in each of 6 directions
Material		Main unit case: Zinc die-casting. Front cover: Acrylic. Operation indicator cover: TPU ^*6
Weight		Approx. 75 g 2.65 oz (no AI imaging illumination unit) Approx. 225 g 7.94 oz (with AI imaging illumination unit)
^1 Focus position can be automatically adjusted during installation. It cannot be adjusted while running. Focus position can be registered separately for each program. ^2 With an AI imaging illumination unit installed, exposure time is up to 6.25 ms. ^3 Maximum exposure time is 500 ms only when lighting is set to OFF. ^4 Except when polarizing filters (OP-88642/OP-88643/OP-88646/OP-88647) are installed. ^5 When the operating ambient temperature exceeds 40°C 104°F, install in accordance with KEYENCE instructions, taking appropriate measures for heat dissipation to ensure that the case temperature does not exceed the rated 65°C 149°F. For the case temperature, measure the side with the “IV4 series” label. ^6 ESD safe and IEC61340-5-1 compliant.

Keyence EM-080P Keyence

€444,95

Only 4 units left

Specifications

Model		EM-080P
Type		Shielded
Shape		8 mm 0.31" dia Cylindrical.
Detecting distance		2.0 mm 0.08" ±10%
Detectable object		Ferrous metals (see Characteristics for non-ferrous metals)
Standard target (iron, t=1 mm 0.04")		10 x 10 mm 0.39" x 0.39"
Hysteresis		10% max. of detecting distance
Response frequency		1.2 kHz
Operation mode		N.O.
Temperature characteristics		±10% max. of detecting distance at +23°C 73.4°F, within -10 to +70°C 14 to 158°F
Display indicator		Red LED
Output		PNP
Control output		PNP: 200 mA (30 V) max., Residual voltage: 1 V max.
Housing		Stainless steel
Rating	Power voltage	10.8 to 30 VDC, Ripple (P-P) 10 % or less^*1
	Current consumption	20 mA or less
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +80 °C -13 to 176 °F (No freezing)
	Relative humidity	35 to 95 % RH (No condensation)
Weight		Approx. 42 g (including nuts and 2-m 6.6' cable)
^*1 Make sure that the power voltage stays within 10.8 V to 30 V even if it is affected by ripple effects.

Keyence GL-R20HG Keyence

€3.106,95

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence XG-8702LP Keyence

€29.166,95

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AP-C31K Keyence

€420,95

Only 4 units left

Specifications

Model		AP-C31K
Type		Negative pressure, NPN
Rated pressure		0 to -29.9 inchHg
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 0.43" (11 mm)) Display cycle: 10 times/s
Operation indicator		Red LED x 2 (corresponding to control output 1 and 2)
Display resolution		Normal mode: 0.1 inchHg, Focus mode: 0.01 inchHg
Power consumption	Normal	12 V: 720 mW (60 mA) or less, 24 V: 960 mW (40 mA) or less
	Eco mode	12 V: 480 mW (40 mA) or less, 24 V: 720 mW (30 mA) or less
Display temperature characteristic		±1 % of F.S. max.
Hysteresis		Variable (Standard: 0.5 % of F.S.)^*1
Response time (Chattering prevention function)		2.5, 5, 100, or 500 ms (selectable)
I/O	Analog output	1 to 5 V with load impedance of 1 kΩ max. (or zero-shift input selectable)
	Zero-shift input	Input time: 2 ms or more. (or analog output selectable)
	Control output	NPN open collector 100 mA max. (at 40 V or below) with max. residual voltage of 1 V, 2 outputs (NO or NC selectable)
Pressure port		NPT 1/8 180 ° rotation
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
Environmental resistance	Pressure resistance	500 kPa
	Ambient temperature	0 to 50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polysulfone, Rear housing: PBT, Front seat: Polycarbonate, Pressure port: Zinc die-casting
Accessories		Power supply cord (6.6' 2-m with connector)
Weight		Approx. 30 g (without cable) /Approx. 85 g (with 6.6' 2-m cable)
^*1 A standard of 0.2 % of FS applies while in focus mode.

Keyence OP-88761 Keyence

€0,00

Sold Out

Specifications

Model				OP-88761
Type				M12 8-pin to M12 4-pin adapter cable, PVC
Length				5 m 16.4'

Keyence XG-X2700 Keyence

€3.136,95

In stock, 14 units

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence AS-440-05U (AS-440-05) Keyence

€0,00

Sold Out

Specifications

Model			AS-440-05U
Type			General-use amplifier unit
Sensor head			AH-416
Shape			Cylindrical and threaded, diameter: 14.5
Measuring range			0 to 5 mm 0.20"
Analog output voltage	Output voltage		0 to 5 V
	Impedance		100 Ω
	Resolution		0.1% of F.S.
	Linearity		±1% of F.S.
	Response		3.3 kHz (-3 dB)
Temperature fluctuation	Sensor head		0.03% of F.S./°C^*1
Temperature characteristics	Amplifier unit		0.05% of F.S./°C^*1
Rating	Power voltage		110/120/220/240 VAC ±10 %, 50/60 Hz
	Power consumption		5VA
Environmentalresistance	Enclosure rating	Sensor head	IP67
	Operating ambient temperature		-10 to +60°C 14 to 140°F, No freezing
		Amplifier unit	0 to +50°C 32 to 122°F
Environmental resistance	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight	Sensor head		Approx 75 g
Weight (including cord)	Amplifier unit		Approx 320g
^*1 When the distance between the sensor head and the target is within 50% of the measurement range.

Keyence PR-MB30C3PL Keyence

€282,95

Only 5 units left

Specifications

Model		PR-MB30C3PL^*1
Type		Reflective (Background suppression)
Output		PNP
Shape		Mini-slim
Cable connection		M8 connector (3 pin)
Detection distance		1 to 30 mm 0.039" to 1.181"
Number of control outputs		1 output
Output operation	Output 1	-
	Output 2	Light-ON
Response time	Output 1	-
	Output 2	ON→OFF: 2.7 ms, OFF→ON: 0.5 ms
Sensitivity adjustment		None
Spot diameter		Approx. ø5.5 mm (at 30 mm)
Light source		4 element, point light source, red LED (650 nm)
Mutual interference prevention function		4 sensors
Indicator lamp		Output indicator (orange), stable operation indicator (green), thrubeam type transmitter: power supply indicator (green)
Control output		30 VDC or lower, 50 mA or lower Leakage current: When 3 kΩ load resistance, 0.3 mA or lower. When 1 kΩ load resistance, 0.5 mA or lower. When 0.2 kΩ load resistance, 1.5 mA or lower Residual voltage: When 10 mA or lower, 1.0 V or lower. When 10 to 30 mA, 1.5 V or lower. When 30 to 50 mA, 2.0 V or lower.
Protection circuit		Power supply reverse connection protection, output overcurrent protection, output surge protection, power supply surge protection
Rating	Power voltage	10 to 30 VDC, including 10 % ripple (P-P)
	Current consumption	19 mA
Environmental resistance	Enclosure rating	IP67 (IEC60529), 4X, 6P, 13 (NEMA250)
	Insulation resistance	20 MΩ or higher (500 VDC)
	Ambient light	Incandescent lamp: 5,000 lux or lower, Sunlight: 20,000 lux or lower
	Ambient temperature	-25 to +55 °C -13 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Storage temperature	-25 to +75 °C -13 to 167 °F
	Withstand voltage	1,000 VAC, 50/60 Hz, 1 min
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case: SUS316L, indicator cover/lens cover: polysulfone, cord protector: polymethylpentene, filler: polyester-based resin
Accessories		Instruction Manual
Weight		Approx. 13 g
^*1 The M8 connector (3 pin) type has 1 control output. If "D" is at the end of the part number, the sensor is equipped with a Dark-ON output. If "L" is at the end of the part number, the sensor is equipped with a Light-ON output. Example: The PR-M51C3PL has a Light-ON output.

Keyence OP-88950 Keyence

€0,00

Sold Out

Specifications

Model				OP-88950
Length				5 m 16.4'

Keyence CZ-H35S Keyence

€278,95

Only 9 units left

Specifications

Model		CZ-H35S
Type		Luster cancel
Detecting area		28 to 52 mm 1.10" to 2.05" (Reco mmended: 40 mm 1.57")
Smallest spot diameter		4.5 mm 0.18"dia. at reference distance of 40 mm 1.57"
Light source		Red LED (665 nm)/Green LED (520 nm)/Blue LED (465 nm)
Minimum bend radius of fi ber		25 mm 0.98"
Environmental resistance	Enclosure rating	IP40
	Ambient light	Incandescent lamp: 10,000 lux max., Sunlight: 20,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material		Housing：Triacetate, Polyarylate (Metal section: TYPE 304 stainless steel) , Lens cover：Fiberglass reinforced plastic
Weight		Approx. 40 g

Keyence FD-GD32B Keyence

€0,00

Sold Out

Specifications

Model				FD-GD32B
Pipe size/Outer diameter				1 1/4" (32 A) ø41 to ø45 mm ø1.61" to ø1.77"
Lmin				387 mm 15.24"
Lmax				1100 mm 43.31"
Length x quantity in pack				245 9.65" × 1
Weight				Approx. 0.3 kg

Keyence GL-SS3 Keyence

€0,00

Sold Out

Specifications

Model				GL-SS3
Type				Standard cable
Applicable product				GL-S Series main unit
Number included				1
Cable end				Main unit connection connector - Main unit connection connector
Length				3 m 9.84'
Note				Use this with one-line systems and series connections.
Weight				100 g

Keyence OP-88513 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FD-EPH10 Keyence

€2.257,95

Only 7 units left

Specifications

Model				FD-EPH10
Pipe size	Outer diameter of pipe			ø10 0.39" ^*1
	Compatible outer diameter range	Polyurethane		10.0 ±0.15 mm 0.39" ±0.006"
		Nylon		10.0 ±0.08 mm 0.39" ±0.003"
	Pipe materials			Resin pipe connectible to a one-touch coupling
Supported gases				Air, nitrogen, argon, and non-corrosive gases^*2
Supported gas temperature				−10°C to +60°C 14 to 140°F
Pressure resistance				1 MPa
Flow rate detection principle				Ultrasonic transmission time difference method
Flow rate specifications	Rated flow rate	(volume flow rate)		150 L/min 5.30 CFM
		(20°C 68°F, atmospheric pressure conversion) * Initial display	Gas at 20°C 68°F, 0.0 MPa
			Gas at 20°C 68°F, 0.2 MPa	450 L/min 15.9 CFM
			Gas at 20°C 68°F, 0.4 MPa	750 L/min 26.5 CFM
			Gas at 20°C 68°F, 0.6 MPa	1050 L/min 37.1 CFM
	Measurement accuracy			±(2.0% of RD+1.0% of F.S.)^3^4
	Repeatability			Response time of 250 ms: ±2.5% of F.S.^3^5
Pressure specifications	Rated pressure			−100 kPa to +0.75 MPa * However, the flow rate cannot be measured in the range of −100 to −30 kPa.
	Overall accuracy			±2.0% of F.S.^*3
	Repeatability			Response time of 2.5 ms: ±0.4% of F.S.
Display resolution	Instantaneous flow			0.1/1 L/min
	Accumulated flow			0.1/1/10/100/1000 L
	Pressure			0.1/1 kPa
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Ambient temperature			−10°C to +60°C 14 to 140°F (no freezing)
	Relative humidity			35%RH to 85%RH (no condensation)
	Vibration resistance			10 to 500 Hz, power spectral concentration: 0.816 G²/Hz, XYZ axes
	Shock resistance			100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Sensor unit (parts that do not contact the gas)			PBT/PAR/iron/Brass electroless nickel plating/POM/NBR/stainless steel/aluminum
	Flow channel (parts that contact the gas)			PBT/Brass electroless nickel plating/NBR/nylon
Weight				Approx. 180 g 6.35 oz
^1 To ensure stable detection, it is recommended to use a pipe inner diameter that is at least equivalent to the inner diameter of this product. ^2 Gases that transmit ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^3 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the condition and type of pipes as well as the temperature and type of gas. ^4 This specification is valid when sufficient straight sections of pipe are provided and the flow velocity distribution is stable. This value does not take into account the effects of fluctuations in flow velocity distribution due to facility factors. ^*5 Accuracy improves with longer response times. As a rule, this is by a proportion of √(250 ms/response time)x.

Keyence SV2-C5AG Keyence

€0,00

Sold Out

Specifications

Model				SV2-C5AG
Type				Motor power cable, Hi-flex robotic cable
Length				5 m 16.4'
Note				for 50 W / 100 W motor

Keyence GL-SA24F Keyence

€0,00

Sold Out

Specifications

Model				GL-SA24F
Type				Protection cover Flat type for 24 beam axes
Overview				This protective case protects the main unit from impacts.
Applicable product				GL-S24FH
Number included				1
Length				502.6 mm 19.79"
Material				aluminum
Note				2 each of the following are included: hexagon socket head cap screw (width across flats: 3 mm), washer, and special hexagon socket head cap screw (M4, length: 13 mm, width across flats: 3 mm).
Weight				160 g