1 year warranty
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Altivar |
| Product or Component Type | Variable speed drive |
| Product Specific Application | Simple machine |
| Component name | ATV11 |
| Application market | Asia |
| Assembly style | With heat sink |
| EMC filter | Without EMC filter |
| Built-in fan | With |
| Phase | 3 phase |
| [Us] rated supply voltage | 200...230 V - 15...10 % |
| Supply frequency | 50...60 Hz - 5...5 % |
| Motor power kW | 1.5 kW |
| Line current | 11 A 200 V, Isc = 1 kA |
| Nominal output current | 1.4 A 230 V motor 4 kHz |
| Maximum transient current | 11.2 A 60 s |
| Power dissipation in W | 75 W at nominal load |
| Switching frequency | 2...16 kHz adjustable 4...16 kHz with derating factor |
| Braking torque | 150 % of nominal motor torque with braking resistor at high inertia 20 % of nominal motor torque without braking resistor at no load 80 % of nominal motor torque with braking resistor at no load |
| Asynchronous motor control profile | Sensorless flux vector control with PWM type motor control signal |
| Electrical connection | Terminal 1.5 mm², AWG 14 AI1, RA-RC, LI1...LI4, DO) Terminal 1.5 mm², AWG 14 L1, L2, L3, U, V, W, PA, PC) |
| Supply | Internal supply for logic inputs 15 V +/- 15 %) 100 mA overload and short-circuit protection Internal supply for reference potentiometer (2.2 to 10 kOhm) 5...5.25 VDC 10 mA overload and short-circuit protection |
| Analogue input type | Configurable current AI1 4...20 mA 250 Ohm without adding resistor Configurable voltage AI1 0...5 V 40000 Ohm only with internal supply Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 40000 Ohm |
| Sampling duration | AI1 20 ms analog LI1...LI4 20 ms discrete |
| Response time | 20 ms DO |
| Linearity error | DO +/- 1 % output AI +/- 5 % input |
| Discrete input type | Assignable Ll1 forward 5000 Ohm 15 V 24 V Assignable Ll2 reverse 5000 Ohm 15 V 24 V Assignable Ll3/Ll4 4 preset speeds 5000 Ohm 15 V 24 V |
| Discrete input logic | Positive logic (source) LI1...LI4), < 5 V, > 11 V Logic input not wired LI1...LI4), < 5 V Negative logic (source) LI1...LI4), > 11 V |
| Discrete output type | Assignable as external voltage DO 30 V max, 30 mA Assignable as open collector logic output DO 100 Ohm, 50 mA max Factory set as PWM open collector output DO at 2 kHz 10 mA max Protected relay logic RA-RC 1 NO Assignable as internal voltage DO |
| Minimum switching current | RA-RC 10 mA 24 V DC |
| Maximum switching current | 2 A 250 V AC inductive cos phi = 0.4 7 ms RA-RC 2 A 30 V DC inductive cos phi = 0.4 7 ms RA-RC 5 A 250 V AC resistive cos phi = 1 RA-RC 5 A 30 V DC resistive cos phi = 1 RA-RC |
| Protection type | Line supply overvoltage drive Line supply undervoltage drive Overcurrent between output phases and earth drive Overheating protection drive Short-circuit between motor phases drive Thermal protection motor |
| Frequency resolution | Display unit 0.1 Hz Analog input converter A/D, 10 bits |
| Electromagnetic compatibility | 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to EN/IEC 61000-4-5 Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3 |
| Maximum motor cable length | 65.6 ft (20 m) with additional EMC filter from 2 to 16 kHz EN 55011 class A group 1 16.4 ft (5 m) with additional EMC filter from 2 to 16 kHz EN 55011 class B |
| Vibration resistance | 1 gn (f= 13â¦200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f= 3â¦13 Hz) conforming to EN/IEC 60068-2-6 |
| Shock resistance | 15 gn 11 ms EN/IEC 60068-2-27 |
| Relative humidity | 5â¦93 % without condensation IEC 60068-2-3 5â¦93 % without dripping water IEC 60068-2-3 |
| Ambient air temperature for operation | 14â¦104 °F (-10â¦40 °C) without derating 104â¦122 °F (40â¦50 °C) by removing the protective cover from the top of the drive 122â¦140 °F (50â¦60 °C) by removing the protective cover from the top of the drive with current derating of 2.2 % per °C |
| Operating altitude | <= 3280.84 ft (1000 m) without derating > 3280.84 ft (1000 m) with current derating 1 % per 100 m |
Complementary
| Characteristic | Value(s) |
|---|---|
| Product destination | Asynchronous motors |
| Supply voltage limits | 170â¦253 V |
| Network frequency limits | 47.5â¦63 Hz |
| Speed drive output frequency | 0â¦200 Hz |
| Nominal switching frequency | 4 kHz |
| Speed range | 1â¦20 |
| Transient overtorque | 150...170 % of nominal motor torque |
| Regulation loop | Adjustable frequency Factory-set with the speed loop stability and gain Possible correction for machines with high resistive torque/inertia/fast cycles |
| Motor slip compensation | Adjustable Preset in factory |
| Prospective line Isc | 1 kA |
| Output voltage | <= 2 x power supply voltage |
| Insulation | Electrical between power and control |
| Analogue input number | 1 |
| Discrete input number | 4 |
| Discrete output number | 2 |
| Acceleration and deceleration ramps | Linear from 0 to 99.9 s |
| Braking to standstill | By DC injection |
| Insulation resistance | > 500 MOhm |
| Marking | CE |
| Operating position | Vertical +/- 10 degree |
| CAD overall width | 4.6 in (117 mm) |
| CAD overall height | 5.6 in (142 mm) |
| CAD overall depth | 6.4 in (163 mm) |
| Product Weight | 4.0 lb(US) (1.8 kg) |
The Altistart U01 is a soft start/soft stop unit for 3-phase asynchronous motors. It is designed primarily for combinations with TeSys U starter-controllers. It can be used for a motor rated power up to 3kW or 3hp for 3-phase (200V to 480V AC) and up to 6A rating. It is 45mm wide, this makes it one of the smallest soft starters on the market. It can be installed nearly everywhere. It features an Integrated bypass, this reduces noise and decreases heat dissipation. Its protection index is IP20. It weighs 0.34kg and its dimensions are, 45mm wide, 234mm high, 150mm deep. The Altistart U01 is designed for the following simple applications like conveyors, conveyor belts, pumps, fans, compressors, automatic doors and gates, small cranes and belt-driven machinery. It complies with standards IEC/EN 60947-4-2, and carries UL, CSA, C-Tick, and CCC certifications, and CE marking. It can be easily combined with a TeSys U controller by means of the power connector VW3G4104. It is easy to install on a DIN rail. Altistart 01 combines simplicity with easy cabling, fast configuration and efficiency. Reduced machine wear and minimized maintenance time will optimize operations. Together with TeSys Model U, it provides a unique motor starter solution.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Altistart U01 and TeSys U |
| Product or Component Type | Soft starter |
| Product destination | Asynchronous motors |
| Product Specific Application | Simple machine |
| Device short name | ATSU01 |
| Phase | 3 phase |
| [Us] rated supply voltage | 200...480 V - 10...10 % |
| Motor power kW | 3 kW, 3 phase 400 V 0.75 kW, 3 phase 230 V 2.2 kW, 3 phase 400 V 1 kW, 3 phase 230 V 1.5 kW, 3 phase 400 V |
| Maximum Horse Power Rating | 1 hp, 3 phase 230 V 2 hp, 3 phase 460 V 3 hp, 3 phase 460 V 1.5 hp, 3 phase 230 V |
| IcL starter rating | 6 A |
| Utilisation category | AC-53B EN/IEC 60947-4-2 |
| Current consumption | 65 mA |
| Type of start | Start with voltage ramp |
| Power dissipation in W | 1.5 W at full load and at end of starting 61.5 W in transient state |
Complementary
| Characteristic | Value(s) |
|---|---|
| Assembly style | With heat sink |
| Function Available | Integrated bypass |
| Supply voltage limits | 180â¦528 V |
| Supply frequency | 50...60 Hz - 5...5 % |
| Network Frequency | 47.5...63 Hz |
| Output voltage | <= power supply voltage |
| [Uc] control circuit voltage | 24 V DC +/- 10 % |
| Starting time | 1 s / 100 5 s / 20 10 s / 10 Adjustable from 1 to 10 s |
| Deceleration time symb | Adjustable from 1 to 10 s |
| Starting torque | 30...80 % of starting torque of motor connected directly on the line supply |
| Discrete input type | Logic LI1, LI2, BOOST) stop, run and boost on start-up functions <= 8 mA 27 kOhm |
| Discrete input voltage | 24...40 V |
| Input output isolation | Galvanic between power and control |
| Discrete input logic | Positive LI1, LI2, BOOST < 5 V <= 0.2 mA > 13 V, >= 0.5 mA |
| Discrete output current | 2 A DC-13 3 A AC-15 |
| Discrete output type | Open collector logic LO1 end of starting signal Relay outputs R1A, R1C NO |
| Discrete output voltage | 24 V 6...30 V) open collector logic |
| Minimum switching current | 10 mA 6 V DC relay outputs |
| Maximum switching current | Relay outputs 2 A 30 V DC cos phi = 0.5 20 ms inductive Relay outputs 2 A 250 V AC AC-15 cos phi = 0.5 20 ms inductive |
| Maximum switching voltage | 440 V relay outputs |
| Display type | 1 LED Green)starter powered up 1 LED Yellow)nominal voltage reached |
| Tightening torque | 16.8â¦22.1 lbf.in (1.9â¦2.5 N.m) 4.4 lbf.in (0.5 N.m) |
| Electrical connection | 4 mm screw clamp terminal - rigid 1 1...10 mm² AWG 8 power circuit Screw connector - rigid without cable end 1 0.5...2.5 mm² AWG 14 control circuit 4 mm screw clamp terminal - rigid 2 1...6 mm² AWG 10 power circuit Screw connector - rigid 2 0.5...1 mm² AWG 17 control circuit Screw connector - flexible with cable end 1 0.5...1.5 mm² AWG 16 control circuit 4 mm screw clamp terminal - flexible without cable end 1 1.5...10 mm² AWG 8 power circuit Screw connector - flexible without cable end 1 0.5...2.5 mm² AWG 14 control circuit 4 mm screw clamp terminal - flexible with cable end 2 1...6 mm² AWG 10 power circuit 4 mm screw clamp terminal - flexible without cable end 2 1.5...6 mm² AWG 10 power circuit Screw connector - flexible without cable end 2 0.5...1.5 mm² AWG 16 control circuit |
| Marking | CE |
| Operating position | Vertical +/- 10 degree |
| Height | 9.2 in (234 mm) |
| Width | 1.8 in (45 mm) |
| Depth | 5.9 in (150 mm) |
| Product Weight | 0.75 lb(US) (0.34 kg) |
| Motor power range AC-3 | 0.55â¦1 kW 200â¦240 V 3 phase 1.1â¦2 kW 380â¦440 V 3 phase 2.2â¦3 kW |
| Motor starter type | Soft starter |
The JACP317121 power supply module stands out in the PLCs and machine control category with its specialized focus on providing dependable power solutions. This unit is integral for the smooth functionality of PLC modules and racks, offering a solid foundation for systems requiring consistent power distribution. Crafted with precision for high-demand applications, it is an essential component in the architecture of automated systems, promoting efficiency and reliability.
The discontinued CIMR-JA4A0004BAA AC inverter drive emerges from the J1000 series as an essential component for three-phase systems, offering a solid 480 V and 400 Hz operation. It is engineered to support a 4.1 amp current and outputs a substantial power of 1.5 kW, making it ideal for a range of industrial applications that require precise power control and efficiency. This model's discontinuation places it in a unique position for users looking to preserve or enhance their current setups with a reliable and proven solution.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
Main
| Characteristic | Value(s) |
|---|---|
| Range Compatibility | Lexium SD3 |
| Product or Component Type | Motion control motor |
| Device short name | BRS3 |
| Maximum mechanical speed | 3000 rpm |
| Motor Type | 3-phase stepper motor |
| Number of motor poles | 6 |
| Supply voltage limits | 230 V AC 325 V DC |
| Mounting Support | Flange |
| Motor flange size | 2.3 in (57.2 mm) |
| Length | 6.2 in (157 mm) |
| Centring collar diameter | 1.5 in (38 mm) |
Complementary
| Characteristic | Value(s) |
|---|---|
| centring collar depth | 0.06 in (1.6 mm) |
| Number of mounting holes | 4 |
| Mounting holes diameter | 0.2 in (5.2 mm) |
| Circle diameter of the mounting holes | 2.6 in (66.6 mm) |
| Electrical Connection | Connector |
| Feedback type | Single turn encoder |
| Speed feedback resolution | 10000 points/turn |
| Holding brake | With |
| Shaft end | Smooth shaft |
| Second shaft | Without second shaft end |
| Shaft diameter | 0.3 in (8 mm) |
| Shaft length | 0.8 in (21 mm) |
| nominal torque | 13.3 lbf.in (1.5 N.m) |
| Peak stall torque | 13.54 lbf.in (1.53 N.m) |
| Continuous stall torque | 13.54 lbf.in (1.53 N.m) |
| Holding torque | 15.05 lbf.in (1.7 N.m) |
| Rotor inertia | 0.38 kg.cm² |
| Resolution | 1.8 °, 0.9 °, 0.72 °, 0.36 °, 0.18 °, 0.09 °, 0.072 °, 0.036 ° step angle 200, 400, 500, 1000, 2000, 4000, 5000, 10000 steps number of full steps per revolution |
| Accuracy error | +/- 6 arc min |
| Maximum starting frequency | 8.5 kHz |
| Line Rated Current | 0.9 A |
| Resistance | 25 Ohm winding) |
| Time constant | 4.6 ms |
| Maximum radial force Fr | 25 N second shaft end) 50 N first shaft end) |
| Maximum axial force Fa | 100 N tensile force) 8.4 N force pressure) |
| Service life in hours | 20000 h bearing) |
| Brake pull-in power | 8 W |
| Angular acceleration | 200000 rad/s² |
| Product Weight | 4.4 lb(US) (2 kg) |
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
Sub-base with plug-in electromechanical relay ABE7 - 16 channels - relay 5 mm
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.
PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.