Keyence

SL-V39F Keyence

Specifications

Model				SL-V39F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			11.3^*1
	OFF→ON			51.3^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	103^*6
			Receiver	82^*6
		When the center indicator is OFF	Transmitter	99^*6
			Receiver	77^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			330 g
	Receiver			345 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

$969.29

1-year warranty

FREE WORDWIDE SHIPPING

Est. delivery between and

Condition:

Sealed Surplus

SKU: SL-V39F-Sealed

Sold out

$0.00

Never Used Surplus

SKU: SL-V39F

4 verified stock

$1,695.68

Used

SKU: SL-V39F-Used

4 verified stock

$969.29

Variant

Quantity:

Need More?

Specifications

Model				SL-V39F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			11.3^*1
	OFF→ON			51.3^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	103^*6
			Receiver	82^*6
		When the center indicator is OFF	Transmitter	99^*6
			Receiver	77^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			330 g
	Receiver			345 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Specifications

Model				SL-V39F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			11.3^*1
	OFF→ON			51.3^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	103^*6
			Receiver	82^*6
		When the center indicator is OFF	Transmitter	99^*6
			Receiver	77^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			330 g
	Receiver			345 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

SL-V39F Keyence

Specifications

Specifications

Specifications

SL-V39F Keyence

Specifications

Specifications

Trusted By

You may also like

Recently viewed