Machine Vision Systems

0.00 kr

Sold Out

Specifications

Model		CA-HS035MU
Image element		Monochrome CMOS, 7× high-speed reading using square-pixel
Unit cell size		7.4 µm × 7.4 µm 0.29 Mil × 0.29 Mil
Valid pixel count		0.31 megapixel mode: 640 (H) × 480 (V), 0.24 megapixel mode: 512 (H) × 480 (V)
Image size		Equivalent to 1/3"
Scanning system		Progressive 4.5 ms
Pixel transfer frequency		86 MHz (43 MHz × 2)
Transfer system		Digital serial transfer
Electronic shutter		Can be set to 0.05 to 100 msec by specifying the following numerical inputs: 1/15, 1/30, 1/60, 1/120, 1/240, 1/500, 1/1000, 1/2000, 1/5000, 1/10000, 1/20000
Lens mount		Special mount (M10.5 P0.5 male)
Environmental resistance	Ambient temperature	0 to 40°C 32 to 104°F
	Relative humidity	85% RH or less
Weight		Approx. 75 g (not including lens)

Keyence SJ-E108H Keyence

0.00 kr

Sold Out

Specifications

Model		SJ-E108H
Ion generation method		Corona discharge method
Structure		Shockless resistive coupling type
Voltage application method / Applied voltage		Pulse AC method/±8000 V
Ion balance control method		Hi-Power I.C.C. method
Ion balance		±30 V^*1
Installation distance		50 to 2000 mm 1.97" to 78.74"
Control input	Static elimination stop input	NPN open collector or contact point signal without voltage
Control output	Ion level warning, condition warning, alarm output	NPN open collector, Maximum 100 mA (40 VDC or less)
	Condition alarm output
	Alarm output
Communication function		Remote control communication
Major functions		Condition alarm, ion level alarm, alarm output
Air connection port		Rc 1/8
Air supply pressure		0.1 MPa to 0.5 MPa^*2 (recommended air pressure of 0.2 MPa)
Effective length		1140 mm 44.88"^*3
Total length		1040 mm 40.94"
No. ofelectrodes		33
Rating	Power voltage	24 VDC to 36 VDC ±10%
	Current consumption	700 mA (at 24 V), 500 mA (at 36 V)
	Overvoltage category	I
	Pollution degree	2
Environmental resistance	Ambient temperature	0 to +40 °C 32 to 104 °F
	Relative humidity	35 to 85 % RH (No condensation)
Material	Electrode probe	Tungsten
	Main body	ABS/PBT/PP/LCP/PPS/SPS/SUS
Weight		1300 g 45.86oz
^1 Measured under the following conditions. Installation distance: 300 mm 11.81" or more, Air supply pressure: 0.2 Mpa, Frequency: The highest device driving frequency, Operating ambient temperature: 0 to +40°C 32 to 104°F, Operating ambient humidity: 35 to 65% RH ^2 Contact KEYENCE when using the air purge function with intermittent air supply. ^*3 Effective length is for static elimination range when installation distance is 50 mm 1.97".

Keyence GL-FB1000 Keyence

0.00 kr

Sold Out

Specifications

Model				GL-FB1000^1^2
Length				1029 mm 40.51"
Recommended compatible models				GL-R63F / GL-R32H / GL-R16L GL-R71F / GL-R36H / GL-R18L GL-R79F / GL-R40H / GL-R20L GL-R87F / GL-R44H / GL-R22L
^1 It is also possible to install light curtains with a body length of 640 mm 25.20" or less. ^2 If the total length of the GL-R series is 1280 mm 50.39" or more, use GL-RB01 or GL-RB21 together with the anti-vibration bracket GL-RB32 (incl. 2 pieces).

Keyence FU-67TG-2000 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence KV-B16XA Keyence

6,324.00 kr

Only 4 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-88632 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SV3-M010AK Keyence

0.00 kr

Sold Out

Specifications

Model				SV3-M010AK
General specifications	Applicable servo amplifier			SV3-010L2
	Rated output			100 W
	Rated torque			0.318 N·m ^*1
	Instant maximum torque			1.11 N·m
	Rated current			0.85 Arms
	Instant maximum current			3.1 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.413 N·m/Arms
	Rotor moment of inertia			0.0705 ×10^-4 kg·m²
	Rated power rating			14.3 kW/s
	Rated angle acceleration			45,100 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			35×
	Approx. weight			0.4 kg 14.11 oz
^*1 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence OP-84457 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-42336 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FU-67 Keyence

1,251.00 kr

Only 7 units left

Specifications

Model		FU-67^*1
Size		M6
Detection arrangement		Parallel
Fibre unit length		2 m78.74" free-cut
Fibre unit diameter		ø2.2×2
Shape		Straight
Minimum bend radius		R2 mm0.079" Tough-Flex
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 21 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence OP-83198 Keyence

0.00 kr

Sold Out

Specifications

Model				OP-83198
Overview				Front protective cover protecting detection side of light curtain.
Applicable product				SL-V72H, SL-V36L
Number included				1 pcs.
Length				1,430.2 mm 56.31"
Material				Translucent plastic: Polycarbonate Black plastic: ABS
Note				To install this product on both the transmitter and receiver, 2 sets are required. Use the dimming filters (sold separately) by attaching them to the front protection cover. When the front protection cover is attached, the L-shaped mounting bracket (OP-42

Keyence CV-M30 Keyence

10,627.00 kr

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence IV3-500MA Keyence

22,836.00 kr

In stock, 15 units

Specifications

Model		IV3-500MA
Type		Standard
Installed distance		50 mm 1.97" or more ^*1
Tools	Available modes	Standard mode / Sorting mode
	Tool with standard mode	Learning, Outline, Color area ^2, Area ^3, Edge pixels, Color average ^2, Brightness average ^3, Width, Diameter, Edge presence, Pitch, OCR, Color prohibit ^*4, Brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge), Blob count
	Number of tools	Total: 65 tools ^*5
Field of view		Installed distance 50 mm 1.97": 22 (H) × 16 (V) mm 0.87" (H) × 0.63" (V) to Installed distance 3000 mm 118.11": 1184 (H) × 888 (V) mm 46.61" (H) × 34.96" (V)
Switch settings (programs)		128 programs (when using SD card) / 32 programs (when not using SD card)
Image receiving element	Type	1/2.9 inch monochrome CMOS
	Number of pixels	1280 (H) × 960 (V)
Image history	Number of storable images	100 images ^*6
	Save conditions	Selectable between NG only, NG and OK near threshold ^7, and All ^6
Focus adjustment		Auto ^*4
Image data transfer	Transfer destination	Selectable between SD card, FTP server and SFTP server
	Transfer format	Selectable between bmp, jpeg, iv3p, and txt, and file names can be modified
	Transfer conditions	Selectable between NG only, NG and OK near threshold ^*8, and All
Exposure time		12 μs to 10 ms
Analysis information	RUN display	Tools list (Judgment results, degree of similarity, or degree of similarity bar display) ^*8
	RUN information	Switchable between OFF, histogram, processing time, count, and output monitor Histogram: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGs Processing time: Processing time (latest, Max., Min., Ave.) Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errors, Strobe errors Output monitor: ON/OFF status by output ^*8
Lights	Illumination	Infrared LED
	Lighting method	Pulse lighting
Other functions	Image capture function	Digital zoom (2×, 4×), HDR, High gain, Color filter ^2, White balance ^2, Brightness correction, AI capture
	Tool functions	Additional learning, Mask outline, Masking function, Color extraction/exclusion ^2, Color histogram function ^2, Monochrome histogram function ^*3, Scaling function
	Utilities	Failing sensor list, Failure hold, Test run, I/O monitor, Security settings (Two-factor password), Simulator ^*9, Additional FTP/SFTP Image Information, Multi-position adjustment, Multi-master image registration, High-speed program switching, Auto program switching, Auto setting backup/restore, Threshold changing in RUN
Indicators		OUT, TRIG, STATUS, LINK/ACT, SD
Input	Type	Switchable between non-voltage input and voltage input For no-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 30 V, ON voltage 18 V or higher, OFF current 0.15 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs	6 ports, 3 ports are selectable as IN/OUT
	Function	IN1: External trigger, IN2, IN3, I/O1 to I/O3: Enable by assigning optional functions Assignable functions: Program switching, Clear error, External master image registration, SD card save cancel
Output	Type	Photo MOS relay output, N.O./N.C. Switchable Maximum rating 30 V 50 mA, residual voltage 1.5 V or less ^*10
	Number of outputs	6 ports, 3 ports are selectable as IN/OUT
	Function	Enable by assigning the optional functions Assignable functions: Total judgment (OK/NG), Run, Busy, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card error, Variety discrimination result, Master judgment result
Power/I/O	Connector	M12 12 pin A code Male connector
	PoE	PoE power Class 3/4/6 ^*11
Ethernet	Standard	1000BASE-T/100BASE-TX
	Connector	M12 8 pin X code Female connector
Network function		FTP client, SFTP client
Interface compatibility	Built-in Ethernet	EtherNet/IP™, PROFINET ^*12, TCP/IP non-procedure communication
Expanded memory		microSD card (microSD/microSDHC) ^*13
Ratings	Power voltage	24 VDC +25%/-20% (including ripple) ^*14
	Current consumption	3.3 A or less (without the AI Lighting unit, and including the output load) 1.8 A or less (AI Lighting unit, and including the output load) ^*15
Environmental resistance	Enclosure rating	IP67 ^*16
	Ambient temperature	0 to +50°C 32 to 122°F (No freezing) ^*17
	Relative humidity	35 to 85% RH (No condensation)
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours in each of the X, Y, and Z directions ^*18
	Shock resistance	500 m/s² 1640'/s², 3 times in each of the 6 directions ^*18
Material		Main unit case: Aluminum die-casting/PBT/TPU Indicator light cover: TPU Ethernet connector: Aluminum die-casting/LCP Front cover: Acrylic (hard coating) Power connector: Aluminum die-casting/LCP Nameplate: PET Water proof cap for the Power connector: PC+ABS alloy Water proof cap for the Ethernet connector: PC
Weight		Approx. 300 g 10.59 oz (without the AI Lighting unit) Approx. 495 g 17.47 oz (with the AI Lighting unit)
^1 Removing the polarizing filter is recommended when used at distances of 3 m 9.8' or more. ^2 Color type only. ^3 Monochrome type only. ^4 The focusing position can be automatically adjusted at the time of installation. Disabled during operation. The focusing position can be registered by programs. ^5 Tools can be installed by programs. This is the number of detection tools and position adjustment tools. Up to 64 detection tools can be set. The number of detection tools in Sorting mode are eight tools. ^6 Saves to the sensor’s internal memory. The images saved to the sensor can be backed up to a USB memory stick inserted into the control panel (IV3-CP50) or to the PC where the software for the IV3 Series (IV3-H1) is being used. ^7 Learning tool only. ^8 Can also be displayed on the control panel (IV3-CP50) or the software for the IV3 Series (IV3-H1). ^9 Usable on the software for the IV3 Series (IV3-H1). ^10 Make sure to keep a total of each output with 120 mA or less. ^11 For a PoE power supply device, IEEE802.3at power class 4 or higher is recommended when using the AI Lighting unit, and IEEE802.3bt power class 6 or higher is recommended when the AI Lighting unit is not used. When using PoE operation may be restricted due to power limitation. ^12 Conformance Class B, applicable protocol: LLDP, SNMP. ^13 Use only products recommended by KEYENCE. ^14 When using the OP-88656 (10 m 32.8'), the power voltage is 24 V DC +25%/-10% (including ripple). ^15 The peak current is designed to be smaller if the AI Lighting unit is mounted. The peak current is greater if the AI Lighting unit is not mounted. ^16 Except when the polarizing filter (OP-88640/OP-88641/OP-88644/OP-88645) is mounted. ^17 For situations where the operating ambient temperature will exceed 40°C 104°F, follow KEYENCE’s specified heat dissipation measures to ensure the case temperature does not exceed the rated maximum temperature (65°C 149°F). Check the instruction manual for more information. ^18 Except when the dome attachment (IV3-D10) is mounted.

Keyence FU-80MTZ Keyence

4,435.00 kr

Only 5 units left

Buy the Keyence FU-80MTZ - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence FU-80MTZ is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence LV-H100-T Keyence

6,781.00 kr

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence XG-H1XA Keyence

5,722.00 kr

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SI-F10 Keyence

0.00 kr

Sold Out

Specifications

Model		SI-F10
Type		Long distance type Sensor head
Measurement range		11.3 to 12.35 mm 0.44" to 0.49" ^*1
Light source		Infrared SLD Central wavelength 820 nm Output 0.6 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
Spot diameter		ø40 µm ø0.001575"^*3
Linearity		±0.3 µm ±0.000012"^*4
Resolution		0.25 µm 0.00000984"^*5
Sampling cycle		200 µs
Light source for guide		Red semiconductor laser Wavelength 655 nm Output 0.1 mW Class 1 Laser product (IEC60825-1/FDA (CDRH) Part 1040.10^*2)
LED display		Target near center of measurement range: green lights. Target within measurement range: orange lights. Target outside measurement range: Flashes orange.
Temperature fluctuation		0.01% of F.S./°C
Environmental resistance	Enclosure rating	IP64
	Ambient light	Incandescent lamp or Fluorescent lamp: 10,000 lux max.
	Ambient temperature	0 to +40 °C 32 to 104 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		SUS
Material	Sensor head
	Spectrum unit	Polycarbonate
Weight		Approx. 38 g (including cable)
^1 Indicates distance from the front of the sensor head. For long distance type sensor heads there is an individual difference of up to ±0.2 mm ±0.01". ^2 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^3 Indicates the minimum beam spot diameter within the measurement range. ^4 This value is obtained when the measurement target is a glass plate with the number of averaging measurements set to 256. ^*5 This value is obtained by measuring a glass plate surface located at the center of the measurement range with the number of averaging measurements set to 4,096.

Keyence FD-HCC2 Keyence

0.00 kr

Sold Out

Specifications

Model				FD-HCC2
Cable end				M12, 8-pin female to M12, 4-pin male
Length				2 m 6.6'
Material				PVC
Weight				Approx. 120 g

Keyence OP-89263 Keyence

0.00 kr

Sold Out

Specifications

Model				OP-89263^*1
Maximum input voltage				1000 V DC+AC peak *When connected to NR-HV04/NR-FV04 1000 Vpeak and 700 Vrms or 700 VDC
Maximum allowable voltage to ground				1000 V CAT II or 600 V CAT III *When connected to NR-HV04/NR-FV04 Measurement terminal, GND terminal 300 Vrms (CAT II)
Attenuation ratio				1:1
Connector				Insulated BNC connector
Cable length				150 cm
Weight				Approx. 120 g
^*1 These specifications refer to the probe only. When connected to a measurement device, refer to the maximum input voltage and amount of ground voltage for the device.

Keyence ER-18PC Keyence

0.00 kr

Sold Out

Specifications

Model		ER-18PC ^*1
Type		Ultra-long distance shielded type Screw type M18 Connector (M12 4-pin) PNP output
Power supply cable length		― ^*2
No. of control outputs		2
Output mode	Output 1	N.O.
	Output 2	N.C.
Button		Available
Button	Function	Distance switching, Through-Metal
Detecting distance	With default settings (Mode 1)	15 mm 0.59" ±10% ^*3
	With distance switching (Mode 2)	10 mm 0.39" ±10% ^*3
Response frequency	With default settings (Mode 1)	20 Hz ^4 ^5
	With distance switching (Mode 2)	50 Hz ^4 ^5
Hysteresis distance		15% or less of detecting distance
Detectable object		Magnetic metal, Non-magnetic metal ^*6
Standard detectable object (Iron, t = 1 mm 0.04")		45 × 45 mm 1.77" × 1.77"
Temperature characteristics		±10% or less of detecting distance at +25°C +77°F (-25 to +55°C -13°F to +131°F) ±15% or less of detecting distance at +25°C +77°F (+55 to +70°C 131°F to 158°F)
Control output		Open-collector, 30 VDC or less 100 mA or less for 1 output, or 100 mA or less in total for 2 outputs
Control output	Residual voltage	PNP output: 2.1 V or less (Output current: 10 mA or less) / 2.4 V or less (Output current: 10 to 100 mA) ^*7
Power supply	Power voltage	16 to 30 VDC (including 10% or less ripple (P-P)), Class 2
	Power consumption (excluding load current)	PNP output: 1140 mW or less (48 mA or less at 24 V, 72 mA or less at 16 V) ^*8
Protection circuit		Protection against reverse power connections, output short-circuits, and reverse output connections
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient temperature	-25 to +70°C -13°F to +158°F (no freezing) ^*9
	Relative humidity	Up to 95% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	1000 m/s² 3280.8 ft/s² (100 G), 10 times in each of the X, Y, and Z directions
Material		Detecting surface: LCP, Mounting screw: SUS303 (M30: SUS304), Case resin: PBT, Button: PBT, Nut: SUS304, Toothed lock washer: SUS304 [Connector] Indicator: PBT (M8: LCP), Connector: PBT (M8: LCP), Case: SUS303 [Connector with pigtail] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC, Connector resin: TPU, Connector metal: Nickel-plated brass [Cable] Indicator: TPU, Cable cap (M8 only): PBT, Cable: PVC
Accessories		Nut ×2, Toothed lock washer ×1
Weight		Approx. 65 g 2.29 oz
^1 Supports IO-Link specification v1.1/COM2 (38.4 kbps). ^2 Ensure the power cable is no longer than 30 m 98.4' for connector and connector with pigtail types and no longer than 20 m 65.6' with IO-Link connections. ^3 The distance at which a standard detectable object can be detected when the unit is mounted without being affected by surrounding metal. ^4 Value when a standard detectable object is used, the distance between detectable objects is twice the standard detectable object, and the distance to the detection target is 1/2 the detecting distance. ^5 The response frequency varies depending on the operating temperature. The response frequency at temperatures of +55°C +131°F or higher is 50% of that at +25°C +77°F. ^6 Detecting distance varies according to the material and size. See the characteristic diagrams for details. ^7 Residual voltage is for when a 2 m 6.6' cable is used. ^8 For IO-Link-compatible devices listed under 1, power consumption is as follows. M8: 840 mW or less (35 mA or less at 24 V, 53 mA or less at 16 V) M12: 1090 mW or less (46 mA or less at 24 V, 69 mA or less at 16 V) M18, M30: 1250 mW or less (53 mA or less at 24 V, 79 mA or less at 16 V) ^9 The upper limit of the UL temperature rating is +55℃ +131℉.

Keyence FD-MZ100ATK Keyence

10,516.00 kr

Only 1 unit left

Specifications

Model		FD-MZ100ATK^*1
Type		Vertical
Shape		Built-in amplifier
Rated flow range		1.4 - 26.0 G/min (5.0 - 100 L/min)^*1
Possible display range		1.4 - 52.8 G/min (5.0 - 200 L/min)^*2
Possible ranges to set		0 - 52.8 G/min (0 - 200 L/min)
Connection port		NPT1 (25 A)
Detectable fluids		Water or non-corrosive liquid
Conductivity of detection fluids		5 µS/cm or higher
Detection fluid temperature		0 to +85°C 32 to 185 °F (No freezing)
Pressure loss		Max. 1.45 PSI (0.01 MPa)
Display method		Dual row display with 4-digit, 7 segment LED, bar display (2 colors), output indicators, flow indicator
Display resolution		0.1/1 (G/min, L/min) selectable
Repeatability		0.5 s : ±5% of F.S., 1 s : ±3.5% of F.S., 2.5 s : ±2.5% of F.S., 5 s : ±1.6% of F.S., 10 s : ±1% of F.S., 30 s : ±0.8% of F.S., 60 s : ±0.6% of F.S.^*3
Hysteresis		Variable
Response time (chatter prevention feature)		0.5 s/1 s/2.5 s/5 s/10 s/30 s/60 s variable
Accumulated flow unit		0.1/1/10/100/1000 (G, L) selectable
Integration data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length : 10 years or longer, Data read/write frequency : 1 million times or more)
Analog output		4-20 mA, max. load resistance 260 Ω Analog output range can be set to any value
Integration reset/bank switch input/flow zero function input		Input time : 20 ms or greater,Select either the accumulation output or the accumulation pulse by setting the mode
Power consumption (Current consumption)		Normal : 1700 mW (70 mA), Power save : 1000 mW (40 mA)
Rating	Power voltage	24 VDC, Ripple (P-P) 10 % or less, Class 2
Environmental resistance	Enclosure rating	IP65
	Pressure resistance	290 PSI (2.0 MPa)
	Applied pressure range	Max. 145 PSI (1.0 MPa)
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material	Liquid end materials	Bore : SCS13, Measurement pipe : PPS, O ring : fluoro-rubber (FKM)
	Other materials	Plastic case areas : PPS, Metal case areas : SUS430, Cable : PVC
Accessory		Instruction Manual, Connector cable (2.7 m 106.3")
Weight		Approx. 1,340 g
^1 The rated flow range indicates recommended operating range. ^2 Can be used within the display range as well as within the rated flow range. ^*3 The repeatability is effective within the display range. Convert the F.S. (full scale) listed in the table according to the rated flow range.

Keyence GL-S20SH Keyence

17,684.00 kr

Only 6 units left

Specifications

Model				GL-S20SH
Type				Slim type
Detection capability				ø25 mm ø0.98"
Total length				419.5 mm 16.52"
No. of beam				20
Detection height				380mm 14.96"
Protection height				426mm 16.77"
Beam axis spacing				20 mm 0.79"
Operating distance				0.1 to 2 m 0.3' to 6.6'
Effective aperture angle				Max. ±3.75° (when the operating distance is 2 m 6.6')
Light source				Infrared LED (870 nm)
Response time(ms)	Wire synchronization, one-line, or optical synchronization system (channel 0)	ON→OFF		6.6 ^*1
		OFF→ON		48.7 ^1 ^2
		All blocked→ON		63.1 ^1 ^3
	Optical synchronization system (channel A or B)	ON→OFF		8.8 ^*1
		OFF→ON		52.0 ^1 ^2
		All blocked→ON		71.9 ^1 ^3
OSSD operation				Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver				Optical synchronization or wire synchronization (determined by the wiring)
Light interference prevention function				Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output type			2 transistor outputs (PNP or NPN output is determined by the cable type.)
	Max. load current			Max. 300 mA
	Residual voltage (when ON)			Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF state voltage			Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current			Max. 200 µA
	Max. load capacitance			2.2 µF
	Load wiring resistance			Max. 2.5 Ω
Inputs 1 and 2				Short-circuit current: approx. 1 mA
Power supply	Current consumption(mA)	When the center indicator is ON	Transmitter	39^*4
			Receiver	62^*4
		When the center indicator is OFF	Transmitter	28^*4
			Receiver	50^*4
	Power voltage			24 VDC ±20%, ripple (P-P) 10% or less, Class 2
Protection circuit				Reverse current protection, short-circuit protection and surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1: 2015 (Category 4, PLe) UL508, UL1998 GB/T4584
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 3,000 lux or less, Sunlight: 20,000 lux or less
	Operating ambient temperature			-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (no condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Polyarylate
Weight	Transmitter			160 g
	Receiver			165 g
^1 If the response time (ON to OFF) exceeds 18 ms, this unit cannot be used as a certified product based on the Chinese standard GB/T4584 “压力机用光电保护装置技术条件”. In the case of series connection, if the total number of beam axes exceeds 100, the response time must be limited to 30 ms or less. When the GL-S units are connected in series, the response time is calculated according to the following steps; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. (ON → OFF) One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms (OFF → ON) One sub unit connected: 42 ms Two sub units connected: 84 ms ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-S operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-S synchronizes the transmitter and receiver first and then determines the clear or blocked. ^4 The control output (OSSD) current is not included. When inputs are turned ON, the current consumption increases by 1 mA per input.

Keyence GL-VM88HN Keyence

0.00 kr

Sold Out

Specifications

Model			GL-VM88HN
Beam axis spacing/Lens diameter			20 mm 0.79": ø5 ø0.197"
Number of beam axes			88
Total length			1760 mm 69.29"
Detection height			1740 mm 68.50"
Protection height			1785 mm 70.28"
Minimum detectable object size			ø25 mm ø0.98" ^*1
Detecting distance			0.3 to 15 m 1.0' to 49.2' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	7.5
		OFF→ON	50.7 ^*3
		All blocked→ON	61.3 ^*4
	With channel A or B	ON→OFF	23.8
		OFF→ON	78.0 ^*3
		All blocked→ON	111.8 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	173 ^*5
		Receiver	188 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	61 ^*5
		Receiver	66 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		1140 g 40.24 oz
	Receiver		1160 g 40.94 oz
	Total		2300 g 81.19 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence OP-M1950 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.