Keyence

NU-EP1 Keyence

Specifications

Model		NU-EP1
Name		Communication unit that supports EtherNet/IP™
Ethernet Specifications	Compliant standards	IEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX), IEEE802.3af (Power over Ethernet, Class 3)
	Transmission rate	10 Mbps (10BASE-T), 100 Mbps (100BASE-TX)
	Transmission media	STP or category 3 or higher UTP (10BASE-T),^*1 STP or category 5 or higher UTP (100BASE-TX)
	Maximum cable length	100 m 328.1' (the length between this unit and the Ethernet switch)
	Max. number of connection stages	4 (10BASE-T) 2 (100BASE-TX)^*2
EtherNet/IP™	Compliant functions	Cyclic communication (implicit messages), message communication (explicit messages)
	Number of connections	64
	RPI (Transmission cycle)	0.5 to 10,000 ms (in units of 0.5 ms)
	Tolerable communication bandwidth for cyclic communication	6,000 pps
	Message communication	Supports UCMM, Class 3
	Conformance test	Supports version A7
Sensor connection	Connectable sensors	Sensor amplifier that supports N-bus^*3
	Number of connectable units	16 maximum^*4
	Power supply	Power is supplied by this unit through the sensor amplifier connection connector.
	Allowable passing current	Total: 1,200 mA or less^*5
	Power during PoE power receiving	Supply voltage: 24 V ±10 %, supply current: 360 mA or less^6 (UL Class 2)^7
Indicator lamp		Link/activity indicator (LINK/ACT): green LED, module status indicator (MS): 2-color (green and red) LED, network status indicator (NS): 2-color (green and red) LED, sensor communication indicator (N-bus): 2-color (green and red) LED
Power voltage		24 VDC ±10 %, ripple (P-P): 10 % or less (when using the power supply connector); 48 VDC (57 V maximum; during PoE power receiving)
Power consumption		1,500 mW or less (60 mA or less at 24 V)^*8
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit case and dust cover: polycarbonate, power supply connector: polyamide (plug), PBT (socket)
Accessories		Instruction manual, power supply connection connector, end unit x 2
Weight		Approx. 80 g (including connectors)
^1 When using the PoE power receiving function to form a connection, use an STP cable or category 5 or higher UTP cable. ^2 When using the switch, there is no limit on the number of units that can be connected. ^3 "N-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^4 This varies depending on the connected sensor amplifiers. ^5 This is the current that can be supplied to the main unit or to the sensor amplifier connected to the main unit. ^6 This varies depending on the ambient usage temperature. (-20 to 45 °C -4 to 113°F: 360 mA or less, 45 to 50 °C 113 to 122°F: 260 mA or less, 50 to 55 °C 122 to 131°F: 140 mA or less) ^7 Power which can be supplied to the sensor amplifi er when using the PoE power receiving function ^8 The current supplied to the connected sensor amplifiers is not included.

€323,95

1-year warranty

FREE WORDWIDE SHIPPING

Est. delivery between and

Condition:

Sealed Surplus

SKU: NU-EP1-Sealed

Sold out

€0,00

Never Used Surplus

SKU: NU-EP1

5 verified stock

€323,95

Used

SKU: NU-EP1-Used

2 verified stock

€278,95

Variant

Quantity:

Need More?

Specifications

Model		NU-EP1
Name		Communication unit that supports EtherNet/IP™
Ethernet Specifications	Compliant standards	IEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX), IEEE802.3af (Power over Ethernet, Class 3)
	Transmission rate	10 Mbps (10BASE-T), 100 Mbps (100BASE-TX)
	Transmission media	STP or category 3 or higher UTP (10BASE-T),^*1 STP or category 5 or higher UTP (100BASE-TX)
	Maximum cable length	100 m 328.1' (the length between this unit and the Ethernet switch)
	Max. number of connection stages	4 (10BASE-T) 2 (100BASE-TX)^*2
EtherNet/IP™	Compliant functions	Cyclic communication (implicit messages), message communication (explicit messages)
	Number of connections	64
	RPI (Transmission cycle)	0.5 to 10,000 ms (in units of 0.5 ms)
	Tolerable communication bandwidth for cyclic communication	6,000 pps
	Message communication	Supports UCMM, Class 3
	Conformance test	Supports version A7
Sensor connection	Connectable sensors	Sensor amplifier that supports N-bus^*3
	Number of connectable units	16 maximum^*4
	Power supply	Power is supplied by this unit through the sensor amplifier connection connector.
	Allowable passing current	Total: 1,200 mA or less^*5
	Power during PoE power receiving	Supply voltage: 24 V ±10 %, supply current: 360 mA or less^6 (UL Class 2)^7
Indicator lamp		Link/activity indicator (LINK/ACT): green LED, module status indicator (MS): 2-color (green and red) LED, network status indicator (NS): 2-color (green and red) LED, sensor communication indicator (N-bus): 2-color (green and red) LED
Power voltage		24 VDC ±10 %, ripple (P-P): 10 % or less (when using the power supply connector); 48 VDC (57 V maximum; during PoE power receiving)
Power consumption		1,500 mW or less (60 mA or less at 24 V)^*8
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit case and dust cover: polycarbonate, power supply connector: polyamide (plug), PBT (socket)
Accessories		Instruction manual, power supply connection connector, end unit x 2
Weight		Approx. 80 g (including connectors)
^1 When using the PoE power receiving function to form a connection, use an STP cable or category 5 or higher UTP cable. ^2 When using the switch, there is no limit on the number of units that can be connected. ^3 "N-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^4 This varies depending on the connected sensor amplifiers. ^5 This is the current that can be supplied to the main unit or to the sensor amplifier connected to the main unit. ^6 This varies depending on the ambient usage temperature. (-20 to 45 °C -4 to 113°F: 360 mA or less, 45 to 50 °C 113 to 122°F: 260 mA or less, 50 to 55 °C 122 to 131°F: 140 mA or less) ^7 Power which can be supplied to the sensor amplifi er when using the PoE power receiving function ^8 The current supplied to the connected sensor amplifiers is not included.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Specifications

Model		NU-EP1
Name		Communication unit that supports EtherNet/IP™
Ethernet Specifications	Compliant standards	IEEE802.3 (10BASE-T), IEEE802.3u (100BASE-TX), IEEE802.3af (Power over Ethernet, Class 3)
	Transmission rate	10 Mbps (10BASE-T), 100 Mbps (100BASE-TX)
	Transmission media	STP or category 3 or higher UTP (10BASE-T),^*1 STP or category 5 or higher UTP (100BASE-TX)
	Maximum cable length	100 m 328.1' (the length between this unit and the Ethernet switch)
	Max. number of connection stages	4 (10BASE-T) 2 (100BASE-TX)^*2
EtherNet/IP™	Compliant functions	Cyclic communication (implicit messages), message communication (explicit messages)
	Number of connections	64
	RPI (Transmission cycle)	0.5 to 10,000 ms (in units of 0.5 ms)
	Tolerable communication bandwidth for cyclic communication	6,000 pps
	Message communication	Supports UCMM, Class 3
	Conformance test	Supports version A7
Sensor connection	Connectable sensors	Sensor amplifier that supports N-bus^*3
	Number of connectable units	16 maximum^*4
	Power supply	Power is supplied by this unit through the sensor amplifier connection connector.
	Allowable passing current	Total: 1,200 mA or less^*5
	Power during PoE power receiving	Supply voltage: 24 V ±10 %, supply current: 360 mA or less^6 (UL Class 2)^7
Indicator lamp		Link/activity indicator (LINK/ACT): green LED, module status indicator (MS): 2-color (green and red) LED, network status indicator (NS): 2-color (green and red) LED, sensor communication indicator (N-bus): 2-color (green and red) LED
Power voltage		24 VDC ±10 %, ripple (P-P): 10 % or less (when using the power supply connector); 48 VDC (57 V maximum; during PoE power receiving)
Power consumption		1,500 mW or less (60 mA or less at 24 V)^*8
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit case and dust cover: polycarbonate, power supply connector: polyamide (plug), PBT (socket)
Accessories		Instruction manual, power supply connection connector, end unit x 2
Weight		Approx. 80 g (including connectors)
^1 When using the PoE power receiving function to form a connection, use an STP cable or category 5 or higher UTP cable. ^2 When using the switch, there is no limit on the number of units that can be connected. ^3 "N-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^4 This varies depending on the connected sensor amplifiers. ^5 This is the current that can be supplied to the main unit or to the sensor amplifier connected to the main unit. ^6 This varies depending on the ambient usage temperature. (-20 to 45 °C -4 to 113°F: 360 mA or less, 45 to 50 °C 113 to 122°F: 260 mA or less, 50 to 55 °C 122 to 131°F: 140 mA or less) ^7 Power which can be supplied to the sensor amplifi er when using the PoE power receiving function ^8 The current supplied to the connected sensor amplifiers is not included.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

NU-EP1 Keyence

Specifications

Specifications

Specifications

NU-EP1 Keyence

Specifications

Specifications

Trusted By

You may also like

Recently viewed