1 year warranty
| Characteristic | Value(s) |
|---|---|
| Phase | Three phase |
| [Us] rated supply voltage | 200...240 V - 10...15 %)three phase |
| Supply voltage limits | 200â¦255 V three phase |
| Supply frequency | 50/60 Hz - 5...5 % |
| Network Frequency | 47.5...63 Hz |
| EMC filter | Without EMC filter |
| Continuous output current | 22.9 A 8 kHz |
| Output current 3s peak | 61 A 220 V |
| Continuous power | 4500 W 220 V |
| Nominal power | 4.5 kW 220 V 8 kHz |
| Switching frequency | 8 kHz |
| Overvoltage category | III |
| Maximum leakage current | 1.55 mA |
| Output voltage | <= power supply voltage |
| Electrical isolation | Between power and control |
| Type of cable | Shielded motor cable 32â¦131 °F (0â¦55 °C)) copper |
| Electrical connection | Spring terminal 6 mm², AWG 10 L1-L2) Spring terminal 6 mm², AWG 10 R, S, T) Spring terminal 6 mm², AWG 10 U, V, W, PE) Spring terminal 6 mm², AWG 10 PA/+, PBe) |
| Discrete input number | 8 programmable CN1) 1 pulse train input (PTI) CN1) 2 fast capture CN1) 1 safety function STO CN9) |
| Discrete input voltage | 24 V DC logic |
| Discrete input logic | Positive or negative CN1) |
| Discrete output number | 5 logic output CN1)12...24 V DC 1 pulse train output (PTO) CN1) |
| Discrete output voltage | 12...24 V DC |
| Discrete output logic | Positive or negative CN1) |
| Analogue input number | 2 |
| Absolute accuracy error | 0.1 % |
| Analogue input type | V_REF voltage analog input - 10...10 V 10 kOhm 14 bits T_REF voltage analog input |
| Control signal type | Servo motor encoder feedback CN2 |
| Protection type | Against reverse polarity inputs signal Against short-circuits outputs signal Overcurrent motor Overvoltage motor Undervoltage motor Overheating motor Overload motor Overspeed motor |
| Safety function | STO (safe torque off), Integrated |
| Safety level | SIL 2 IEC 61800-5-2 2007 SIL 2 IEC 61508-1 2010 PL d/category 3 ISO 13849-1 2008 SIL 2 ISO 13849-1 2009/AC SIL 2 IEC 60204-1 2006 SIL 2 IEC 60204-1 2009/A1 SIL 2 IEC 60204-1 2010/AC SIL 2 IEC 62061 2012 |
| Communication interface | CANopen, Integrated CANmotion, Integrated |
| Connector type | RJ45 CN4)CANopen, CANmotion |
| Method of access | Slave |
| Transmission rate | 250 kbit/s 328.08â¦820.2 ft (100â¦250 m) CANopen, CANmotion 500 kbit/s 13.1â¦328.08 ft (4â¦100 m) CANopen, CANmotion 1 Mbit/s 13.1 ft (4 m) CANopen, CANmotion |
| Number of addresses | 1â¦127 CANopen, CANmotion |
| Physical interface | RS485 Modbus Serial line slave |
| Status LED | 1 LED (Red) charge 1 LED (Green) RUN 1 LED (Red) error |
| Signalling function | Servo status and fault codes five 7-segment display units |
| Marking | CULus CSA CE |
| type of cooling | Integrated fan |
| Operating position | Vertical |
| Product compatibility | Servo motor BCH2 7.09 in (180 mm), 3 4500 W Servo motor BCH2 7.09 in (180 mm), 2 3500 W |
| Width | 4.6 in (116 mm) |
| Height | 9.2 in (234 mm) |
| Depth | 7.3 in (186 mm) |
| Product Weight | 7.05 lb(US) (3.2 kg) |
| Supply voltage description | Three phase 220 V AC 50...60 Hz |
| Network number of phases | 3 |
| Drive voltage drop coefficient | 1 |
| Field weakening | False |
| Continuous output current 2 | 22.9 A |
| Output current 3s peak 2 | 61 A 220 V |
| Switching frequency 2 | 8 kHz |
| Continuous output current 3 | 22.9 A |
| Output current 3s peak 3 | 61 A 220 V |
| Switching frequency 3 | 8 kHz |
| Communication interface | CANmotion Pulse train input Pulse train output CANopen DS402 |
| Emc filter compatibility | Type 023 |
All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.
If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.
In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.
PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.
Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.
PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.
Trusted By
Need More?
Contact Us
we're here to support your business.
"Fast service for obsolete parts"
Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!
Buyer at GE Health
"Helping us move projects forward"
With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.
Buyer at E-Merge Systems – A Rockwell Integrator