IX-H2000 Keyence

Specifications

Model			IX-H2000
Main unit / expansion unit			Main unit
Display	Min. display unit	Z axis	10 μm ^*1
		X axis	50 μm ^*1
	Display range	Z axis	±999.99 to ±999 mm 39.33" (with 4 selectable steps) ^*1
		X axis	±999.95 to ±999 mm 39.33" (with 4 selectable steps) ^*1
Tools	Scan mode		Height, Step, Average height, Pin height, MAX/MIN, Height area, Monochrome area, Width, Step calculation, Thickness calculation, Position adjustment, 1-axis adjustment, 2-axis adjustment (Max. number of settings) Judgment: 16 tools, Position adjustment: 1 tool^*2
	Line mode		Height (Ave./Max./Min.), Step (Ave./Max./Min.), Edge position, Width/diameter, Step/width calculation, Thickness calculation, Position adjustment, Tilt adjustment (Max. number of settings) Judgment: 16 tools ^3, Position adjustment: 1 tool, Tilt adjustment: 1 tool^2
Other functions	Common		Zero/offset, Operating threshold adjustment, 2-point calibration, Measurement direction, Position correction NG measurement, Zero/offset recording, Capture mode (HDR), Sensor date/time information addition, N.O./N.C. switching, I/O monitor, Automatic brightness adjustment, Lighting (ON/OFF), Total judgment conditions, NPN/PNP switching, Simultaneous main unit/expansion unit input, Mutual interference prevention, Security
	Scan mode		Measurement range, Measurement position (small/standard/large), Measurement mode, Measurement noise elimination, Imaging mode (high gain), Tilt correction (fixed or real-time correction), Glare removal, Trigger input (internal/external), Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Area height histogram, Fixed reference area, Mask outline, Rotation range, Height image display on tool setting screen, Scaling function
	Line mode		Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.), Laser sensitivity adjustment, Averaging filter, Median filter, X-axis median filter
Input	Input		Switchable between non-voltage input and voltage input For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs		8 (IN1 to IN8)
	Function		IN1: External trigger ↑↓ / Timing input, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Laser emission stop, Zero/offset (batch), Reset (error only), Reset (judgment value only) Reset (judgment value and error)
Output	Output		Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 2 V or less
	Number of inputs		10 (OUT1 to OUT10)
	Function		Enable by assigning the optional functions Assignable functions: Total judgment result (All OK/Any OK/NG), Run, Busy, Error, Position adjustment result, Tilt adjustment result, Result of the logical operation of each tool, Monochrome area / Height area tool result (OK/NG), Height / Step / Max./Min. / Calculation tool result (OK/NG/HIGH/LO), Alarm
Analog voltage output			±5 V, 1 to 5 V, 0 to 5 V, Output impedance: 100 Ω ^*4
Analog current output			4 to 20 mA, Max. load resistance: 350 Ω ^*4
Number of programs			32
Statistical information			Scan mode: Measured value / Degree of similarity (Max., Min., Ave.), Processing time (Latest, Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) Line mode: Measured value / Degree of similarity (Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) ^1 ^5
Detection history	Saved history	Scan mode	50 (FTP/SFTP client function: Enabled/High-resolution mode: Enabled) 80 (FTP/SFTP client function: Enabled/High-resolution mode: Disabled) 70 (FTP/SFTP client function: Disabled/High-resolution mode: Enabled) 100 (FTP/SFTP client function: Disabled/High-resolution mode: Disabled) ^*6
		Line mode	400 (FTP/SFTP client function: Enabled/High-resolution mode: -) 500 (FTP/SFTP client function: Disabled/High-resolution mode: -) ^*6
	Save conditions		Selectable between NG only and All ^*6
Image data transmission (FTP/SFTP client function)	Destination		FTP/SFTP server
	Method		Selectable between bmp, jpeg, and txt
	Conditions		4 conditions Selectable between All, Total judgment result (OK/NG), Result of each tool (OK/(NG and ALM)), and Result of the logical operation of each tool (OK/NG)
Ethernet	Standard		100BASE-TX/10BASE-T ^*7
	Connector		RJ45 8-pin connector ^*7
Interface compatibility			CC-Link, DeviceNet®, EtherNet/IP™, EtherCAT®, RS-232C, BCD output, TCP/IP non-procedural communication ^*8
Number of connectible units			Main units: 1, Expansion units: 1, Communication units (DL): 1
Ratings	Power voltage		24 VDC ±10% (including ripple)
	Current consumption		Max. 1.9 A or less (With main unit only: 0.8 A or less, With unit expansion: 1.9 A or less) (Excluding output load) ^*9
Environmental resistance	Ambient temperature		0 to +50°C 32 to 122°F (No freezing)
	Relative humidity		35 to 85% RH (No condensation)
Material			Main unit case: PC / Power connector: PA, POM / Analog output connector: PA, POM / I/O connector: PA / Head connector: Zinc + Ni plating, PA / Ethernet connector: Copper alloy + Ni plating / Rear heat sink: Aluminum / Main unit rear DIN rail fixing tab: POM / Nameplate: PC
Weight			Approx. 210 g
^1 For displaying on an IX Series control panel or PC software. ^2 Configurable for each program. ^3 Up to 8 tools can be used for the diameter tool only. ^4 Select ±5 V, 1 to 5 V, 0 to 5 V, or 4 to 20 mA for use. ^5 When sample hold (edge), peak/bottom/P-P hold (level/edge) is set. ^6 Saves to the sensor amplifier’s internal memory. Detection history saved inside the sensor amplifier can be backed up to a PC using the USB memory stick connected to the IX Series control panel or PC software. ^7 For connection to an IX Series control panel or PC software. The RJ45 connector on the main unit is used for connecting to the expansion unit. ^8 When a DL Series device is used. Contact KEYENCE for information on other interfaces. ^*9 Includes a DL Series communication unit.

Est. delivery between and

€1.081,95

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: IX-H2000-Sealed

11 verified stock

€1.081,95

Never Used Surplus

SKU: IX-H2000

2 verified stock

€1.020,95

Used

SKU: IX-H2000-Used

4 verified stock

€618,95

Variant

Quantity:

Need More?

Specifications

Model			IX-H2000
Main unit / expansion unit			Main unit
Display	Min. display unit	Z axis	10 μm ^*1
		X axis	50 μm ^*1
	Display range	Z axis	±999.99 to ±999 mm 39.33" (with 4 selectable steps) ^*1
		X axis	±999.95 to ±999 mm 39.33" (with 4 selectable steps) ^*1
Tools	Scan mode		Height, Step, Average height, Pin height, MAX/MIN, Height area, Monochrome area, Width, Step calculation, Thickness calculation, Position adjustment, 1-axis adjustment, 2-axis adjustment (Max. number of settings) Judgment: 16 tools, Position adjustment: 1 tool^*2
	Line mode		Height (Ave./Max./Min.), Step (Ave./Max./Min.), Edge position, Width/diameter, Step/width calculation, Thickness calculation, Position adjustment, Tilt adjustment (Max. number of settings) Judgment: 16 tools ^3, Position adjustment: 1 tool, Tilt adjustment: 1 tool^2
Other functions	Common		Zero/offset, Operating threshold adjustment, 2-point calibration, Measurement direction, Position correction NG measurement, Zero/offset recording, Capture mode (HDR), Sensor date/time information addition, N.O./N.C. switching, I/O monitor, Automatic brightness adjustment, Lighting (ON/OFF), Total judgment conditions, NPN/PNP switching, Simultaneous main unit/expansion unit input, Mutual interference prevention, Security
	Scan mode		Measurement range, Measurement position (small/standard/large), Measurement mode, Measurement noise elimination, Imaging mode (high gain), Tilt correction (fixed or real-time correction), Glare removal, Trigger input (internal/external), Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Area height histogram, Fixed reference area, Mask outline, Rotation range, Height image display on tool setting screen, Scaling function
	Line mode		Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.), Laser sensitivity adjustment, Averaging filter, Median filter, X-axis median filter
Input	Input		Switchable between non-voltage input and voltage input For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs		8 (IN1 to IN8)
	Function		IN1: External trigger ↑↓ / Timing input, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Laser emission stop, Zero/offset (batch), Reset (error only), Reset (judgment value only) Reset (judgment value and error)
Output	Output		Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 2 V or less
	Number of inputs		10 (OUT1 to OUT10)
	Function		Enable by assigning the optional functions Assignable functions: Total judgment result (All OK/Any OK/NG), Run, Busy, Error, Position adjustment result, Tilt adjustment result, Result of the logical operation of each tool, Monochrome area / Height area tool result (OK/NG), Height / Step / Max./Min. / Calculation tool result (OK/NG/HIGH/LO), Alarm
Analog voltage output			±5 V, 1 to 5 V, 0 to 5 V, Output impedance: 100 Ω ^*4
Analog current output			4 to 20 mA, Max. load resistance: 350 Ω ^*4
Number of programs			32
Statistical information			Scan mode: Measured value / Degree of similarity (Max., Min., Ave.), Processing time (Latest, Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) Line mode: Measured value / Degree of similarity (Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) ^1 ^5
Detection history	Saved history	Scan mode	50 (FTP/SFTP client function: Enabled/High-resolution mode: Enabled) 80 (FTP/SFTP client function: Enabled/High-resolution mode: Disabled) 70 (FTP/SFTP client function: Disabled/High-resolution mode: Enabled) 100 (FTP/SFTP client function: Disabled/High-resolution mode: Disabled) ^*6
		Line mode	400 (FTP/SFTP client function: Enabled/High-resolution mode: -) 500 (FTP/SFTP client function: Disabled/High-resolution mode: -) ^*6
	Save conditions		Selectable between NG only and All ^*6
Image data transmission (FTP/SFTP client function)	Destination		FTP/SFTP server
	Method		Selectable between bmp, jpeg, and txt
	Conditions		4 conditions Selectable between All, Total judgment result (OK/NG), Result of each tool (OK/(NG and ALM)), and Result of the logical operation of each tool (OK/NG)
Ethernet	Standard		100BASE-TX/10BASE-T ^*7
	Connector		RJ45 8-pin connector ^*7
Interface compatibility			CC-Link, DeviceNet®, EtherNet/IP™, EtherCAT®, RS-232C, BCD output, TCP/IP non-procedural communication ^*8
Number of connectible units			Main units: 1, Expansion units: 1, Communication units (DL): 1
Ratings	Power voltage		24 VDC ±10% (including ripple)
	Current consumption		Max. 1.9 A or less (With main unit only: 0.8 A or less, With unit expansion: 1.9 A or less) (Excluding output load) ^*9
Environmental resistance	Ambient temperature		0 to +50°C 32 to 122°F (No freezing)
	Relative humidity		35 to 85% RH (No condensation)
Material			Main unit case: PC / Power connector: PA, POM / Analog output connector: PA, POM / I/O connector: PA / Head connector: Zinc + Ni plating, PA / Ethernet connector: Copper alloy + Ni plating / Rear heat sink: Aluminum / Main unit rear DIN rail fixing tab: POM / Nameplate: PC
Weight			Approx. 210 g
^1 For displaying on an IX Series control panel or PC software. ^2 Configurable for each program. ^3 Up to 8 tools can be used for the diameter tool only. ^4 Select ±5 V, 1 to 5 V, 0 to 5 V, or 4 to 20 mA for use. ^5 When sample hold (edge), peak/bottom/P-P hold (level/edge) is set. ^6 Saves to the sensor amplifier’s internal memory. Detection history saved inside the sensor amplifier can be backed up to a PC using the USB memory stick connected to the IX Series control panel or PC software. ^7 For connection to an IX Series control panel or PC software. The RJ45 connector on the main unit is used for connecting to the expansion unit. ^8 When a DL Series device is used. Contact KEYENCE for information on other interfaces. ^*9 Includes a DL Series communication unit.

Model			IX-H2000
Main unit / expansion unit			Main unit
Display	Min. display unit	Z axis	10 μm ^*1
		X axis	50 μm ^*1
	Display range	Z axis	±999.99 to ±999 mm 39.33" (with 4 selectable steps) ^*1
		X axis	±999.95 to ±999 mm 39.33" (with 4 selectable steps) ^*1
Tools	Scan mode		Height, Step, Average height, Pin height, MAX/MIN, Height area, Monochrome area, Width, Step calculation, Thickness calculation, Position adjustment, 1-axis adjustment, 2-axis adjustment (Max. number of settings) Judgment: 16 tools, Position adjustment: 1 tool^*2
	Line mode		Height (Ave./Max./Min.), Step (Ave./Max./Min.), Edge position, Width/diameter, Step/width calculation, Thickness calculation, Position adjustment, Tilt adjustment (Max. number of settings) Judgment: 16 tools ^3, Position adjustment: 1 tool, Tilt adjustment: 1 tool^2
Other functions	Common		Zero/offset, Operating threshold adjustment, 2-point calibration, Measurement direction, Position correction NG measurement, Zero/offset recording, Capture mode (HDR), Sensor date/time information addition, N.O./N.C. switching, I/O monitor, Automatic brightness adjustment, Lighting (ON/OFF), Total judgment conditions, NPN/PNP switching, Simultaneous main unit/expansion unit input, Mutual interference prevention, Security
	Scan mode		Measurement range, Measurement position (small/standard/large), Measurement mode, Measurement noise elimination, Imaging mode (high gain), Tilt correction (fixed or real-time correction), Glare removal, Trigger input (internal/external), Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Area height histogram, Fixed reference area, Mask outline, Rotation range, Height image display on tool setting screen, Scaling function
	Line mode		Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.), Laser sensitivity adjustment, Averaging filter, Median filter, X-axis median filter
Input	Input		Switchable between non-voltage input and voltage input For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs		8 (IN1 to IN8)
	Function		IN1: External trigger ↑↓ / Timing input, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Laser emission stop, Zero/offset (batch), Reset (error only), Reset (judgment value only) Reset (judgment value and error)
Output	Output		Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit), residual voltage of 2 V or less
	Number of inputs		10 (OUT1 to OUT10)
	Function		Enable by assigning the optional functions Assignable functions: Total judgment result (All OK/Any OK/NG), Run, Busy, Error, Position adjustment result, Tilt adjustment result, Result of the logical operation of each tool, Monochrome area / Height area tool result (OK/NG), Height / Step / Max./Min. / Calculation tool result (OK/NG/HIGH/LO), Alarm
Analog voltage output			±5 V, 1 to 5 V, 0 to 5 V, Output impedance: 100 Ω ^*4
Analog current output			4 to 20 mA, Max. load resistance: 350 Ω ^*4
Number of programs			32
Statistical information			Scan mode: Measured value / Degree of similarity (Max., Min., Ave.), Processing time (Latest, Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) Line mode: Measured value / Degree of similarity (Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) ^1 ^5
Detection history	Saved history	Scan mode	50 (FTP/SFTP client function: Enabled/High-resolution mode: Enabled) 80 (FTP/SFTP client function: Enabled/High-resolution mode: Disabled) 70 (FTP/SFTP client function: Disabled/High-resolution mode: Enabled) 100 (FTP/SFTP client function: Disabled/High-resolution mode: Disabled) ^*6
		Line mode	400 (FTP/SFTP client function: Enabled/High-resolution mode: -) 500 (FTP/SFTP client function: Disabled/High-resolution mode: -) ^*6
	Save conditions		Selectable between NG only and All ^*6
Image data transmission (FTP/SFTP client function)	Destination		FTP/SFTP server
	Method		Selectable between bmp, jpeg, and txt
	Conditions		4 conditions Selectable between All, Total judgment result (OK/NG), Result of each tool (OK/(NG and ALM)), and Result of the logical operation of each tool (OK/NG)
Ethernet	Standard		100BASE-TX/10BASE-T ^*7
	Connector		RJ45 8-pin connector ^*7
Interface compatibility			CC-Link, DeviceNet®, EtherNet/IP™, EtherCAT®, RS-232C, BCD output, TCP/IP non-procedural communication ^*8
Number of connectible units			Main units: 1, Expansion units: 1, Communication units (DL): 1
Ratings	Power voltage		24 VDC ±10% (including ripple)
	Current consumption		Max. 1.9 A or less (With main unit only: 0.8 A or less, With unit expansion: 1.9 A or less) (Excluding output load) ^*9
Environmental resistance	Ambient temperature		0 to +50°C 32 to 122°F (No freezing)
	Relative humidity		35 to 85% RH (No condensation)
Material			Main unit case: PC / Power connector: PA, POM / Analog output connector: PA, POM / I/O connector: PA / Head connector: Zinc + Ni plating, PA / Ethernet connector: Copper alloy + Ni plating / Rear heat sink: Aluminum / Main unit rear DIN rail fixing tab: POM / Nameplate: PC
Weight			Approx. 210 g
^1 For displaying on an IX Series control panel or PC software. ^2 Configurable for each program. ^3 Up to 8 tools can be used for the diameter tool only. ^4 Select ±5 V, 1 to 5 V, 0 to 5 V, or 4 to 20 mA for use. ^5 When sample hold (edge), peak/bottom/P-P hold (level/edge) is set. ^6 Saves to the sensor amplifier’s internal memory. Detection history saved inside the sensor amplifier can be backed up to a PC using the USB memory stick connected to the IX Series control panel or PC software. ^7 For connection to an IX Series control panel or PC software. The RJ45 connector on the main unit is used for connecting to the expansion unit. ^8 When a DL Series device is used. Contact KEYENCE for information on other interfaces. ^*9 Includes a DL Series communication unit.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator