GL-S40SH Keyence

Specifications

Model				GL-S40SH
Type				Slim type
Detection capability				ø25 mm ø0.98"
Total length				819.5 mm 32.26"
No. of beam				40
Detection height				780mm 30.71"
Protection height				826mm 32.52"
Beam axis spacing				20 mm 0.79"
Operating distance				0.1 to 2 m 0.3' to 6.6'
Effective aperture angle				Max. ±3.75° (when the operating distance is 2 m 6.6')
Light source				Infrared LED (870 nm)
Response time(ms)	Wire synchronization, one-line, or optical synchronization system (channel 0)	ON→OFF		8.7 ^*1
		OFF→ON		51.9 ^1 ^2
		All blocked→ON		71.8 ^1 ^3
	Optical synchronization system (channel A or B)	ON→OFF		12.3 ^*1
		OFF→ON		57.2 ^1 ^2
		All blocked→ON		85.8 ^1 ^3
OSSD operation				Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver				Optical synchronization or wire synchronization (determined by the wiring)
Light interference prevention function				Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output type			2 transistor outputs (PNP or NPN output is determined by the cable type.)
	Max. load current			Max. 300 mA
	Residual voltage (when ON)			Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF state voltage			Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current			Max. 200 µA
	Max. load capacitance			2.2 µF
	Load wiring resistance			Max. 2.5 Ω
Inputs 1 and 2				Short-circuit current: approx. 1 mA
Power supply	Current consumption(mA)	When the center indicator is ON	Transmitter	50^*4
			Receiver	76^*4
		When the center indicator is OFF	Transmitter	30^*4
			Receiver	55^*4
	Power voltage			24 VDC ±20%, ripple (P-P) 10% or less, Class 2
Protection circuit				Reverse current protection, short-circuit protection and surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1: 2015 (Category 4, PLe) UL508, UL1998 GB/T4584
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 3,000 lux or less, Sunlight: 20,000 lux or less
	Operating ambient temperature			-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (no condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Polyarylate
Weight	Transmitter			305 g
	Receiver			310 g
^1 If the response time (ON to OFF) exceeds 18 ms, this unit cannot be used as a certified product based on the Chinese standard GB/T4584 “压力机用光电保护装置技术条件”. In the case of series connection, if the total number of beam axes exceeds 100, the response time must be limited to 30 ms or less. When the GL-S units are connected in series, the response time is calculated according to the following steps; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. (ON → OFF) One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms (OFF → ON) One sub unit connected: 42 ms Two sub units connected: 84 ms ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-S operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-S synchronizes the transmitter and receiver first and then determines the clear or blocked. ^4 The control output (OSSD) current is not included. When inputs are turned ON, the current consumption increases by 1 mA per input.

Est. delivery between and

€1.580,95

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: GL-S40SH-Sealed

Sold out

€0,00

Never Used Surplus

SKU: GL-S40SH

5 verified stock

€1.580,95

Used

SKU: GL-S40SH-Used

Sold out

€0,00

Variant

Quantity:

Need More?

Specifications

Model				GL-S40SH
Type				Slim type
Detection capability				ø25 mm ø0.98"
Total length				819.5 mm 32.26"
No. of beam				40
Detection height				780mm 30.71"
Protection height				826mm 32.52"
Beam axis spacing				20 mm 0.79"
Operating distance				0.1 to 2 m 0.3' to 6.6'
Effective aperture angle				Max. ±3.75° (when the operating distance is 2 m 6.6')
Light source				Infrared LED (870 nm)
Response time(ms)	Wire synchronization, one-line, or optical synchronization system (channel 0)	ON→OFF		8.7 ^*1
		OFF→ON		51.9 ^1 ^2
		All blocked→ON		71.8 ^1 ^3
	Optical synchronization system (channel A or B)	ON→OFF		12.3 ^*1
		OFF→ON		57.2 ^1 ^2
		All blocked→ON		85.8 ^1 ^3
OSSD operation				Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver				Optical synchronization or wire synchronization (determined by the wiring)
Light interference prevention function				Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output type			2 transistor outputs (PNP or NPN output is determined by the cable type.)
	Max. load current			Max. 300 mA
	Residual voltage (when ON)			Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF state voltage			Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current			Max. 200 µA
	Max. load capacitance			2.2 µF
	Load wiring resistance			Max. 2.5 Ω
Inputs 1 and 2				Short-circuit current: approx. 1 mA
Power supply	Current consumption(mA)	When the center indicator is ON	Transmitter	50^*4
			Receiver	76^*4
		When the center indicator is OFF	Transmitter	30^*4
			Receiver	55^*4
	Power voltage			24 VDC ±20%, ripple (P-P) 10% or less, Class 2
Protection circuit				Reverse current protection, short-circuit protection and surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1: 2015 (Category 4, PLe) UL508, UL1998 GB/T4584
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 3,000 lux or less, Sunlight: 20,000 lux or less
	Operating ambient temperature			-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (no condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Polyarylate
Weight	Transmitter			305 g
	Receiver			310 g
^1 If the response time (ON to OFF) exceeds 18 ms, this unit cannot be used as a certified product based on the Chinese standard GB/T4584 “压力机用光电保护装置技术条件”. In the case of series connection, if the total number of beam axes exceeds 100, the response time must be limited to 30 ms or less. When the GL-S units are connected in series, the response time is calculated according to the following steps; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. (ON → OFF) One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms (OFF → ON) One sub unit connected: 42 ms Two sub units connected: 84 ms ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-S operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-S synchronizes the transmitter and receiver first and then determines the clear or blocked. ^4 The control output (OSSD) current is not included. When inputs are turned ON, the current consumption increases by 1 mA per input.

Model				GL-S40SH
Type				Slim type
Detection capability				ø25 mm ø0.98"
Total length				819.5 mm 32.26"
No. of beam				40
Detection height				780mm 30.71"
Protection height				826mm 32.52"
Beam axis spacing				20 mm 0.79"
Operating distance				0.1 to 2 m 0.3' to 6.6'
Effective aperture angle				Max. ±3.75° (when the operating distance is 2 m 6.6')
Light source				Infrared LED (870 nm)
Response time(ms)	Wire synchronization, one-line, or optical synchronization system (channel 0)	ON→OFF		8.7 ^*1
		OFF→ON		51.9 ^1 ^2
		All blocked→ON		71.8 ^1 ^3
	Optical synchronization system (channel A or B)	ON→OFF		12.3 ^*1
		OFF→ON		57.2 ^1 ^2
		All blocked→ON		85.8 ^1 ^3
OSSD operation				Turns on when no interruptions are present in the detection zone
Synchronization between the transmitter and receiver				Optical synchronization or wire synchronization (determined by the wiring)
Light interference prevention function				Optical synchronization: prevented by Channel A and B with setting switch Wire synchronization: prevented automatically
Control output (OSSD output)	Output type			2 transistor outputs (PNP or NPN output is determined by the cable type.)
	Max. load current			Max. 300 mA
	Residual voltage (when ON)			Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF state voltage			Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current			Max. 200 µA
	Max. load capacitance			2.2 µF
	Load wiring resistance			Max. 2.5 Ω
Inputs 1 and 2				Short-circuit current: approx. 1 mA
Power supply	Current consumption(mA)	When the center indicator is ON	Transmitter	50^*4
			Receiver	76^*4
		When the center indicator is OFF	Transmitter	30^*4
			Receiver	55^*4
	Power voltage			24 VDC ±20%, ripple (P-P) 10% or less, Class 2
Protection circuit				Reverse current protection, short-circuit protection and surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 ClassA, FCC Part15B ClassA, ICES-003 ClassA
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508, EN61508 (SIL3), IEC62061, EN62061 (SIL CL3) EN ISO13849-1: 2015 (Category 4, PLe) UL508, UL1998 GB/T4584
Environmental resistance	Enclosure rating			IP65/IP67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 3,000 lux or less, Sunlight: 20,000 lux or less
	Operating ambient temperature			-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (no condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Polyarylate
Weight	Transmitter			305 g
	Receiver			310 g
^1 If the response time (ON to OFF) exceeds 18 ms, this unit cannot be used as a certified product based on the Chinese standard GB/T4584 “压力机用光电保护装置技术条件”. In the case of series connection, if the total number of beam axes exceeds 100, the response time must be limited to 30 ms or less. When the GL-S units are connected in series, the response time is calculated according to the following steps; 1. Sum up the response time of all unit. 2. Subtract the following time from the result of previous step. (ON → OFF) One sub unit connected: 2 ms Two sub units connected: 4.2 ms (When using Optical synchronization system and Channel A or B) One sub unit connected: 2.7 ms Two sub units connected: 5.7 ms (OFF → ON) One sub unit connected: 42 ms Two sub units connected: 84 ms ^2 If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3 “All blocked” means the situation where the GL-S operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-S synchronizes the transmitter and receiver first and then determines the clear or blocked. ^4 The control output (OSSD) current is not included. When inputs are turned ON, the current consumption increases by 1 mA per input.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator