Sensors

Showing 73 - 96 of 1788 products

€866,95

Only 5 units left

Specifications

Model		NU-CL1
Number of connectable sensors		16 units max. ^*1
Sensor connection	Connectable sensors	Sensor amplifier that supports N-bus^*2
	Number of connectable units	16 maximum^*3
	Power supply	Power is supplied by this product through the wiring-saving connector.
	Allowable passing current	Total: 1,200 mA or less^*4
CC-Link specifications	Supported version	Version 2.00, version 1.10 (switchable)
	Station type	Remote device station
	No. of occupied stations	Version 2.00: 3; version 1.10: 1, 2, 3, 4 (switchable)
	Transmission speed	156kbps/625kbps/2.5Mbps/5Mbps/10Mbps
	Station number settings	1 to 64
Power voltage		24 VDC ± 10%, ripple (P-P) 10% or less
Power consumption		1400 mW or less (at 24 V, 55 mA max.) ^*5
Accessories		Instruction manual, CC-Link connection connector, power supply connection connector, termination resistor (110 Ω, 1/2 W), end unit × 2
Weight		Approx. 80 g (including connectors)
^1 Depends on the sensor amplifi ers connected. ^2 "N-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^3 This varies depending on the connected sensor amplifiers. ^4 This is the current that can be supplied to this unit or to the sensor amplifier linked to this unit. ^*5 Exclusive of the current supplied to the sensors connected.

Keyence NU-EC1A Keyence

€1.035,95

Only 6 units left

Specifications

Model		NU-EC1A^*1
Ethernet Specifications	Compliant standards	IEEE802.3u (100BASE-TX)
	Transmission rate	100 Mbps (100BASE-TX)
	Transmission media	Category 5e or higher STP cable
	Distance between nodes	100 m 328.1'
	Communication ports	RJ45 Connectors × 2
EtherCAT^® Communication Specifications	Supported functions	Process data object communication (Cyclic communication) Mailbox communication Compatible with CoE Explicit Device Identification
Number of connectable sensors		Max. 16 units (Differs depending on the sensor amplifier connected)
Power voltage		24 VDC ±10% Ripple (P-P) 10% max.
Accessories		Instruction manual, power supply connector, end unit × 2
Weight		Approx. 80 g (Including connector)
^*1 EtherCAT^® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.

Keyence OP-81283 Keyence

€0,00

Sold Out

Specifications

Model				OP-81283
Applicable product				DL-RS1A
Length				5 m 16.40'
Note				Connection with external devices that have D-sub 9-pin connectors

Keyence DL-RS1A Keyence

€252,95

In stock, 11 units

Specifications

Model		DL-RS1A^*1
Synchronization between the transmitter and receiver		Asynchronous
Transmission code		ASCII
Baud rate		2,400/4,800/9,600/19,200/38,400 bps selectable (Factory-setting: 9,600 bps)
Data bit length		8 bits/7 bits selectable (Factory-setting: 8 bits)
Parity check		None/Even/Odd selectable (Factory-setting: None)
Stop bit length		1 bit
Data delimiter		Data reception: automatically recognizes CR or CR+LF Data transmission: Fixed to CR+LF
Indicator		Communication indicator lamp (green x 2), Alarm indicator lamp (red), Power indicator lamp (green)
Sensor connection specifications	Number of connectable sensor units	Up to 15 units (including main unit)
Power voltage		20 to 30 VDC, including ripple, Ripple (P-P): 10 % max. Class 2 (Supplied via connected sensor amplifier)
Power consumption		25 mA max.
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Case/Polycarbonate
Weight		Approx. 53 g
Communication method		Full duplex
^*1 For connecting with sensor, please refer to the user's Manual

Keyence DL-RB1A Keyence

€630,95

Only 6 units left

Specifications

Model		DL-RB1A^*1
Indicator		Alarm indicator lamp (red), Power indicator lamp (green)
Sensor connection specifications	Number of connectable sensor units	Up to 15 units (including main unit)
BCD output specifications	I/O terminal	34-pin connector (MIL standard)
	Control output	BCD output: 4 outputs (1 digit) x 6 digits, signed output, strobe output, alarm output, NPN open-collector output: 40 V, 20 mA or less, residual voltage: 1 V or less, positive logic/negative logic (switchable)
	Control input	ID selection input: 4 inputs, data request input, no-voltage input (with contacts, without contacts); input time: 2 ms or more; short-circuit current: 1 mA
Power voltage		20 to 30 VDC, including ripple, Ripple (P-P): 10 % max. Class 2 (Supplied via connected sensor amplifier)
Power consumption		27 mA max.
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Case/Polycarbonate
Weight		Approx. 46 g
^*1 For connecting with sensor, please refer to the user's Manual

Keyence DL-PN1 Keyence

€305,95

Only 9 units left

Specifications

Model		DL-PN1
Type		PROFINET Network communication unit
PROFINET specifications	Conformance class	Conformance Class A
	Number of connections	1
	Compliant protocol	LLDP, DCP
	Update time	2 to 512 ms
	Conformance test	V2.2.4
	Device type	Data I/O Communication Record data Communication
	GSDML Version	Ver. 2.3
Rating	Power voltage	20 to 30 VDC, including Ripple (P-P) 10 % (Supplied from the connected sensor amplifier)
Weight		Approx. 70 g (Including the connector)

Keyence DL-PD1 Keyence

€767,95

Only 9 units left

Specifications

Model		DL-PD1
Sensor connection specifications	Connectable sensors	Sensor amplifiers with D-bus support^*1
	Number of connectable sensor units	15 units max.^*2
PROFIBUS DP specifications	Device type	DP-V1 Slave (D-sub 9 pin, Number of the ports: 1)
	Communication speed	9.6 kbit/s to 12 Mbit/s
	Cable length	9.6 / 19.2 / 45.45 / 93.75 kbit/s : 1200 m 187.5 kbit/s : 1000 m 500 kbit/s : 400 m 1.5 Mbit/s : 200 m 3 / 6 / 12 Mbit/s : 100 m
Power voltage		20 to 30 VDC, including ripple (p-p) 10% (This voltage is supplied from the connected sensor amplifier.)
Power consumption		1600 mW or less (65 mA max. at 24 V)
Environmental resistance	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Material		Main unit case and dust cover: Polycarbonate PROFIBUS connector: Steel – Nickel plating
Weight		Approx. 65 g
^1 "D-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^2 Varies with the sensor amplifiers connected.

Keyence DL-NS1 Keyence

€794,95

Only 1 unit left

Specifications

Model		DL-NS1
Cable connector		M12 Male
USB connector		USB TypeA
USB Communication		USB2.0 Full Speed
Interface		USB-COM
OS		Windows 11 Home/Pro/Enterprise (32bit/64bit) Windows 10 Home/Pro/Enterprise (32bit/64bit) One OS must be installed.
Control input	The number of input	2
	Input type	Voltage input
	Maximum rating	26.4V
	Minmum ON voltage	DC15V
	Maximum OFF current	0.2mA
Control output	The number of output	2
	Output type	Photo relay output
	Control output current	30VDC 50mA max.per output
	Maximum leak current	0.1mA max.
	Maximum residual voltage	1V max.
Switch input	Input type	No-voltage input
	Supplied voltage	Approx. 5V
	Supplied current	10mA max.
Power voltage		USB bus power
Power consumption		100mA max.
Environmental resistance	Ambient temperature	-10 to +50 °C 14 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit：Polycarbonate(PC)、Cable：PVC
Weight		Approx. 45 g (including the cable)

Keyence DL-EP1 Keyence

€325,95

Only 4 units left

Specifications

Model		DL-EP1^*1
Indicator		Link/activity indicator (LINK/ACT): Green LED, Module status indicator (MS): 2-color (green/red) LED, Network status indicator (NS): 2-color (green/red) LED, Sensor communication indicator (D-bus) 2-color (green/red) LED
Sensor connection specifications	Connectable sensors	Sensor amplifiers with D-bus support^*2
	Number of connectable sensor units	Up to 15 units
EtherNet/IP™specifications	Compliant functions	Cyclic communication (Implicit messaging)Message communication (Explicit messaging)Compatible with UCMM and Class 3
	Number of connections	64
EtherNet/IP™ specifications	RPI (Transmission cycle)	0.5 to 10000 ms (0.5 ms unit)
EtherNet/IP™specifications	Tolerable communication bandwidth forcyclic communication	6000pps
EtherNet/IP™ specifications	Conformance test	Compatible with Version A7
Power voltage		20 to 30 VDC, including ripple, Ripple (P-P): 10% max. Class 2 (Supplied via connected sensor amplifier)
Power consumption		1500 mW or less (at 30 V 50 mA max)
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit case: Polycarbonate
Weight		Approx. 70g
^1 For connecting with sensor, please refer to the user's Manual ^2 "D-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers.

Keyence DL-EN1 Keyence

€518,95

Only 6 units left

Specifications

Model		DL-EN1
Ethernet specifications	Compliant standards	IEEE802.3u (100BASE-TX)
	Transmission speed	100Mbps (100BASE-TX)
	Transmission interface	STP cable or Category 5 or higher UTP cable (100BASE-TX)
	Maximum cable length	100 m (Distance between DL-EN1 and Ethernet switch)
Performance specifications	Socket communication, no-protocol commands, ASCII	TCP socket 1 Port number can be set between 1 and 65535 8500: Reserved for the system Initial value: 64000
Sensor connection specifications	Connectable sensors	Sensor amplifiers with D-bus support^*1
	Number of connectable sensor units	15 units max^*2
Indicator lamps		Link/activity indicator (LINK/ACT): Green LED Module status indicator (MS): 2-color (green/red) LED Network status indicator (NS): 2-color (green/red) LED Sensor communication indicator (D-bus): 2-color (green/red) LED
Power voltage		20 to 30 VDC ±10%, including ripple (p-p)10% (supplied from the connected sensor amplifiers)
Power consumption		1500 mW or less (at 30 V 50 mA max)
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit case: Polycarbonate
Weight		Approx. 70 g
^1 "D-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^2 Varies with the sensor amplifiers connected.

Keyence DL-EC1A Keyence

€305,95

Only 9 units left

Specifications

Model		DL-EC1A
Ethernet specifications	Compliant standards	IEEE802.3u (100BASE-TX)
	Transmission speed	100 Mbps (100BASE-TX)
	Transmission interface	Category 5e or higher STP cable
	Distance between nodes	100 m 3937.01'
	Communication port	RJ-45 x 2
EtherCAT communication specifications	Compatible functions	Process data object communication (cyclic communication) Mailbox communication (message communication) CoE compatible Explicit Device Identification
	Conformance test version	Complies with V2.0.42
Sensor connection specifications	Connectable sensors	Sensor amplifiers with D-bus support^*1
	Number of connectable sensor units	15 units max.^*2
Indicator lamps		Power indicator (PWR): Green LED RUN indicator (RUN): Green LED ERR indicator (ERR): Red LED Sensor communication indicator (D-bus): 2-color (green/red) LED Link/activity indicator: Green LED
Power voltage		20 to 30 VDC, including ripple (p-p) of 10 % supplied from the connected sensor amplifiers
Power consumption		2,100 mW or less (at 30 V, 70 mA max.)
Environmental resistance	Pollution degree	2
	Ambient temperature	-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Main unit: Polycarbonate
Weight		Approx. 70 g (including connectors)
^1 D-bus is the name of KEYENCE's wiring-saving system for sensor amplifiers. ^2 This varies depending on the connected sensor amplifiers.

Keyence DL-DN1 Keyence

€859,95

Only 9 units left

Specifications

Model				DL-DN1^*1
DeviceNet® specifi cations	Network power supply			11 to 25 VDC (supplied from DeviceNet® communication power supply)
Indicator				Network status indicator: 2-color (green/red) LED, Module status indicator: 2-color (green/red) LED, Sensor communication indicator: 2-color (green/red) LED
Sensor connection specifications	Connectable sensors			Sensor amplifiers with D-bus support^*2
	Number of connectable sensor units			Up to 15 units
DeviceNet® specifi cations	Compliant functions			Remote I/O communication (polling) Explicit messaging
	Address setting			0 to 63 (PGM compatible)
	Baud rate (automatically switched)			500 kbps/250 kbps/125 kbps
	Maximum cable length	500 kbps	thick cable	100 m 328.09' (thick cable)
			thin cable
		250 kbps	thick cable	250 m 820.21' (thick cable)
			thin cable	100 m 328.09' (thick cable)
		125 kbps	thick cable	500 m 1640.42' (thick cable)
			thin cable	100 m 328.09' (thick cable)
Power voltage				20 to 30 VDC, including ripple, Ripple (P-P): 10 % max. Class 2 (Supplied via connected sensor amplifier)
Power consumption				660 mW or less (at 30 V, 22 mA max.)
Environmental resistance	Pollution degree			2
	Ambient temperature			-20 to +55 °C -4 to 131 °F (No freezing)
	Relative humidity			35 to 85 % RH (No condensation)
	Vibration resistance			10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material				Main unit case and dust cover: Polycarbonate, DeviceNet® connector: Polyamide (plug), PUT (socket)
Weight				Approx. 80 g
^1 For connecting with sensor, please refer to the user's Manual ^2 "D-bus" is the name of KEYENCE's wiring-saving system for sensor amplifiers.

Keyence DL-CL1 Keyence

€325,95

In stock, 14 units

Specifications

Model		DL-CL1^*1
Supported version		Version 2.00, version 1.10 (switchable)
CC-Link specifications	No. of occupied stations	Version 2.00: 1 station x 8, 2 stations x 8, 4 stations x 2 (switchable), version 1.10: 1 station, 2 stations, 4 stations (switchable)
	Station type	Remote device station
	Transmission speed	156 kbps/625 kbps/2.5 Mbps/5 Mbps/10 Mbps
	Station number settings	1 to 64
Power voltage		20 to 30 VDC, including ripple, Ripple (P-P): 10 % max. Class 2 (Supplied via connected sensor amplifier)
Weight		Approx. 80 g
^*1 For connecting with sensor, please refer to the user's Manual