Sensors

Showing 25 - 48 of 1788 products

€194,95

Only 10 units left

Specifications

Model		LV-21AP
Type		PNP output
Main unit/expansion unit		Main unit
Control output		PNP open-collector x 2 channels, 30 VDC max., max. 100 mA, residual voltage (1.0 V max.)
Response speed		FINE : 80 µs , TURBO : 500 µs , SUPER , TURBO : 4 ms
Number of interference preventive units		FINE : None , TURBO : 2 units , SUPER : 4 units
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Unit expansion		Up to 7 additional expansion units can be installed (8 units including the main unit),
Rating	Power voltage	12 to 24 VDC, Ripple (P-P) 10 % or less
	Power consumption	1.5 W max. (125 mA max. for 12 V, 62.5 mA max. for 24 V)
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing) ^*1
	Relative humidity	35 to 85 % RH (No condensation)
Material	Main unit	Polycarbonate
	Case
Weight		Approx. 75 g
^*1 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 2 to 5 units: -10 to +50 °C 14 to 122 °F When 6 to 7 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA.

Keyence EX-110V Keyence

€186,95

In stock, 44 units

Specifications

Model		EX-110V^*1
Type		Sensor head
Amplifier unit		NPN: EX-V02 PNP: EX-V02P
Shape		M10 x 18 mm 0.71" Threaded
Measuring range		0 to 2 mm 0 to 0.08"
Display range		-19,999 to +19,999
Linearity		±0.3% of F.S.
Resolution (No. of averaging measurements: 64)		0.4 μm
Sampling rate		40,000 samplings max./sec. ^*2
Display speed		20 times/sec.
Display power		7-segment 2-color LED
Over-range alarm		±FFFF is displayed.
Control input		NPN open-collector or non-voltage contact (Timing input, Reset input, Auto-zero input, Comparator output disable input, Synchronous input, External setting input)/PNP: Applied voltage; 10 to 30 V
Control output	Setting method	Upper/lower 2-level setting x 4 patterns (selectable)
	Signal	NPN open-collector (HIGH, GO and LOW): 100 mA max. (40 V max.) PNP open-collector (HIGH, GO and LOW): 100 mA max. (30 V max.)
	Response time	0.075 ms (at maximum speed)
	OFF-delay time	60 ms
Strobe output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.O.)
Alarm output		NPN: 100 mA max. (40 V max.)/PNP: 100 mA max. (30 V max.), Residual voltage: 1 V max. (N.C.)
Analog output voltage	Output voltage	±5V
	Impedance	100 Ω
	Response time	0.075 ms (at maximum speed)
Temperature characteristics		0.07% of F.S./°C ^*3
Major functions		FLL, digital filter, auto zero, offset, calculation, measurement mode (15 types), judgment value memory (4 sets), decimal point shift, display digit changing, display of various errors, etc.
Rating	Power voltage	24 VDC ±10%, Ripple (P-P): 10% max.
	Current consumption	240 mA max.
Environmental resistance	Ambient temperature	-10 to +60 °C 14 to 140 °F, No freezing
	Relative humidity	35 to 85%, No condensation
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 55 g (including 3 m 9.8' cable)
^1 The above data was obtained using an iron target (S45C, SS400, t=1 mm 0.04"). When measuring aluminum, copper, or stainless steel targets, refer to the linear characteristics for these materials. ^2 When the digital filter function is used, the sampling rate is 20,000 sampling/sec. ^*3 When the distance between the sensor head and the target is within 50% of the measuring range.

Keyence LV-NH100 Keyence

€312,95

Only 6 units left

Specifications

Model		LV-NH100
Type		Area thrubeam, High performance
FDA (CDRH) Part 1040.10		Class 1 Laser Product
IEC 60825-1
Light source		Visible red semiconductor laser, Wavelength: 660 nm
Detecting distance	MEGA	2000 mm 78.74" (Detecting area: 10 mm 0.39")
	ULTRA
	SUPER
	TURBO
	FINE
	HSP
Environmental resistance	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
Material	Case	Glass reinforced plastic
	Lens cover	Transmitter: Glass, Receiver: Polyarylate
Weight		Approx. 75 g

Keyence OP-87685 Keyence

€186,95

Only 6 units left

Specifications

Model				OP-87685
Overview				The bracket for IV series.You can attach IV to Φ12mm pipe by using it.
Applicable product				IV series
Weight				Approx. 150 g

Keyence OP-87450 Keyence

€426,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87441 Keyence

€146,95

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence IV-H500MA Keyence

€742,95

In stock, 11 units

Specifications

Model		IV-H500MA
Type		Standard distance
Installed distance		50 to 500 mm 1.97" to 19.69"
View		Installed distance 50 mm 1.97": 25 (H) × 18 (V) mm 0.98" (H) × 0.71" (V) to installed distance 500 mm 19.69": 210 (H) × 157 (V) mm 8.27" (H) × 6.18" (V)
Image sensor	Type	1/3 inch monochrome CMOS
	Pixel	752 (H) x 480 (V) 29.61" (H) x 18.90" (V)
Focus adjustment		Auto^*1
Exposure time		1/10 to 1/25,000
Lights	Illumination	Red LED
	Lighting method	Pulse lighting/DC lighting is switchable
Tools	Type	Shape Detection, Color Area^2, Area^3, Edge Pixels, Width/Height, Diameter, Edge Presence, Pitch, Position Adjustment, High Speed Position Adjustment (1-Axis/2-Axis Adjustment)
	Number	Detection tools: 16 tools, position adjustment tool: 1 tool^*4
Switch settings (programs)		32 programs
Image history	Numbers	300 images^5^6
	Condition	NG only/All is selectable^*6
Analysis information		OFF/Statistics/Histograms/Matching rate list is switchable Statistics: Processing time (latest value, MAX, MIN, AVE), number of OKs, number of NGs, trigger numbers, trigger errors, judgment results list by tools Histograms: Histogram, matching degree (latest value, MAX, MIN, AVE), numbers of OKs, numbers of NGs Matching rate list: Judgment results list by tools, matching rate list by tools, judgment bar list by tools^*7
Other functions		HDR, HighGain, Color filters^2, Digital zoom^8, Brightness correction, Tilt correction, White balance^2, Mask function, Color histogram, Test run, ToolAutoTune, Input monitor, Output test, Security settings, Simulator^9, Sensor date/time information addition, Scaling function, Failing sensor list, Failure hold
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT
Input	Type	Non-voltage input/voltage input is switchable For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Inputs	6 inputs (IN1 to IN6)
	Function	IN1: External trigger, IN2 to IN6: Enable by assigning the optional functions Assignable functions: Program switching, Clear error, External master image registration
Output	Type	Open collector output NPN/PNP is switchable, N.O./N.C. is switchable For open collector NPN output: Maximum rating 26.4 V 50 mA, remaining voltage 1.5 V or lower For open collector PNP output: Maximum rating 26.4 V 50 mA, remaining voltage 2 V or lower
	Outputs	4 outputs (OUT1 to OUT4)
	Function	Enable by assigning the optional functions Assignable functions: Total judge result, RUN, BUSY, Error, Position adjustment result, Judge result of each tool, Result of the logical operation of each tool
Ethernet	Standard	100BASE-TX/10BASE-T^*10
	Connector	M12 4pin connector^*10
Network function		FTP client, EtherNet/IP™, PROFINET
Rating	Power voltage	24 VDC ±10 % (including ripple)
	Current consumption	0.6 A or less
Environmental resistance	Enclosure rating	IP67^*11
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions^*12
	Shock resistance	500 m/s², 3 times in each of 6 directions^*12
Material		Main unit case: Aluminium die-casting, Packing: NBR, Front cover: Acrylic, Mounting adapter: POM
Weight		Approx. 270 g
^1 The focusing position can be automatically adjusted at the time of installation. Deactivated during the operation. Focusing position can be registered by program. ^2 Color type only ^3 Possible with both the Color type and monochrome type ^4 Tools can be installed by programs. ^5 When using the FTP client function: 210 pictures ^6 Saves to the memory in the sensor. The images saved in the sensor can be backed up to the USB memory installed to the intelligent monitor (IV-M30) or to the PC by the software for IV (IV-H1). ^7 This can be displayed on the intelligent monitor (IV-M30) or by software for IV (IV-H1). ^8 Possible with both the color type and monochrome type ^9 Simulator can be used with the IV software (IV-H1). ^10 This is for connection with the intelligent monitor (IV-M30) or software for IV (IV-H1). ^11 Except when polarized filter attachment (OP-87436/OP-87437) is mounted ^12 Except when IV-G dome attachment (IV-D10) is mounted

Keyence FS-N13N Keyence

€173,95

In stock, 34 units

Specifications

Model		FS-N13N
Type		High functionality 2 output Cable
Output		NPN
Main unit/expansion unit		Main unit
Control output		2 NPN open collector 24 V; 1 output max: 100 mA or less; 2 output total: 100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less
Monitor output (1-5 V)		-
External input		1 Input time 2 ms (ON)/20 ms (OFF) or more (25 ms or more (ON/OFF) when external calibration is selected.)
Light source LED		Red, 4-element LED
APC		ON/OFF switchable (Factory setting: OFF)
Response time		50 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER) /4 ms (ULTRA) /16 ms (MEGA)
Number of interference prevention units		0 for HIGH SPEED; 4 for FINE; 8 for TURBO/SUPER/ULTRA/MEGA (When set to double, the number of interference-prevention units will be doubled.)
Unit expansion		Up to 16 units can be connected total (two output type is treated as two units)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current Consumption	Normal: 900 mW or less (36 mA max. at 24 V, 48 mA max. at 12 V)^1 Eco on mode: 800 mW or less (32 mA max. at 24 V, 39 mA max. at 12 V)^1 Eco Full mode: 470 mW or less (19 mA max. at 24 V, 23 mA max. at 12 V)
Environmental resistance	Ambient light	Incandescent lamp: 20,000 lux or less, Sunlight: 30,000 lux or less
	Ambient temperature	-20 to +55 °C -4 to +131 °F (No freezing)^*2
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Both main unit and expansion unit housing material: Polycarbonate
Weight		Approx. 80 g
^1 Increases 100 mW (4.0 mA) for High Speed mode ^2 One or two more units connected: -20 to +55 °C (-4 to +131 °F); 3 to 10 more units connected: -20 to +50 °C (-4 to +122 °F); 11 to 16 more units connected: -20 to +45 °C (-4 to +113 °F). When using 2-outputs, one unit is counted as two units. All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.

Keyence FS-N12CP Keyence

€183,95

In stock, 12 units

Specifications

Model		FS-N12CP
Type		Standard 1 output M8 connector^*1
Output		PNP
Main unit/expansion unit		Expansion unit
Control output		1 PNP open collector 24 V; 1 output max: 100 mA or less; 2 output total: 100 mA or less (used stand-alone)/20 mA or less (multiple connections); residual voltage 1 V or less
External input		1 Input time 2 ms (ON)/20 ms (OFF) or more (25 ms or more (ON/OFF) when external calibration is selected.)
Light source LED		Red, 4-element LED
APC		ON/OFF switchable (Factory setting: OFF)
Response time		50 µs (HIGH SPEED) /250 µs (FINE) /500 µs (TURBO) /1 ms (SUPER) /4 ms (ULTRA) /16 ms (MEGA)
Number of interference prevention units		0 for HIGH SPEED; 4 for FINE; 8 for TURBO/SUPER/ULTRA/MEGA (When set to double, the number of interference-prevention units will be doubled.)
Unit expansion		Up to 16 units can be connected total (two output type is treated as two units)
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current Consumption	Normal: 950 mW or less (39 mA max. at 24 V, 52 mA max. at 12 V)^2 Eco on mode: 850 mW or less (35 mA max. at 24 V, 44 mA max. at 12 V)^2 Eco Full mode: 520 mW or less (21 mA max. at 24 V, 26 mA max. at 12 V)
Environmental resistance	Ambient light	Incandescent lamp: 20,000 lux or less, Sunlight: 30,000 lux or less
	Ambient temperature	-20 to +55 °C -4 to +131 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Both main unit and expansion unit housing material: Polycarbonate
Weight		Approx. 22 g
^1 Use a cable length of 30 m 98.43' or less for M8 connector and e-CON connector types. ^2 Increases 100 mW (4.0 mA) for High Speed mode ^*3 One or two more units connected: -20 to +55 °C (-4 to +131 °F); 3 to 10 more units connected: -20 to +50 °C (-4 to +122 °F); 11 to 16 more units connected: -20 to +45 °C (-4 to +113 °F). When using 2-outputs, one unit is counted as two units. All temperature regulations are for when the unit is mounted on a DIN rail and installed on metal sheeting.

Keyence IV-HG10 Keyence

€407,95

In stock, 15 units

Specifications

Model		IV-HG10
Type		Main unit
Tools	Type	Shape Detection, Color Area^1, Area^2, Edge Pixels, Width/Height, Diameter, Edge Presence, Pitch, Position Adjustment, High Speed Position Adjustment (1-Axis/2-Axis Adjustment), OCR^*3
	Number	Detection tools: 16 tools, position adjustment tool: 1 tool^*4
Switch settings (programs)		32 programs
Image history	Numbers	When using a color type head: 100 images^5, when using a monochrome type head: 300 images^6^*7
	Condition	NG only/All is selectable^*7
Analysis information		OFF/Statistics/Histograms/Matching rate list is switchable Statistics: Processing time (latest value, MAX, MIN, AVE), number of OKs, number of NGs, trigger numbers, trigger errors, judgment results list by tools Histograms: Histogram, matching degree (latest value, MAX, MIN, AVE), numbers of OKs, numbers of NGs Matching rate list: Judgment results list by tools, matching rate list by tools, judgment bar list by tools^*8
Other functions		HDR, HighGain, Color filters^1, Digital zoom (2x, 4x)^9, Brightness correction, Tilt correction, White balance^*1, Mask function, Color histogram, Test run, ToolAutoTune, Input monitor, Output test, Security settings, Simulator, Mutual interference prevention, Direct connection (2 units or more), Sensor date/time information addition, Scaling function, Failing sensor list, Failure hold
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT
Input	Type	Non-voltage input/voltage input is switchable For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Inputs	6 inputs (IN1 to IN6)
	Function	IN1: External trigger, IN2 to IN6: Enable by assigning the optional functions Assignable functions: Program switching, Clear error, External master image registration, Main unit/expansion unit simultaneous input
Output	Type	Open collector output NPN/PNP is switchable, N.O./N.C. is switchable For open collector NPN output: Maximum rating 26.4 V 50 mA (20 mA when linked to an expansion unit [IV-HG15]), remaining voltage 1.5 V or lower For open collector PNP output: Maximum rating 26.4 V 50 mA (20 mA when linked to an expansion unit [IV-HG15]), remaining voltage 2 V or lower
	Outputs	8 outputs (OUT1 to OUT8)
	Function	Enable by assigning the optional functions Assignable functions: Total judgment result, RUN, BUSY, Error, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Main unit/expansion unit logical output
Ethernet	Standard	100BASE-TX/10BASE-T^*10
	Connector	RJ-45 8pin connector^*10
Network function		FTP client, EtherNet/IP™, PROFINET
Rating	Power voltage	24 VDC ±10 % (including ripple)
	Current consumption	0.8 A or less. 1.5 A or less when also using an expansion unit (IV-HG15). (The output load is excluded.)
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)^*11
	Relative humidity	35 to 85 % RH (No condensation)
Material		Main unit case: Polycarbonate
Weight		Approx. 150 g
^1 Color type only ^2 Monochrome type only ^3 Supported with Ver. R5.00.00 or later. ^4 Tools can be installed by programs. ^5 When using the FTP client function: 70 pictures ^6 When using the FTP client function: 210 pictures ^7 Saves to the sensor amplifier's internal memory. The images saved to the sensor amplifier can be backed up to the USB memory device inserted into the intelligent monitor (IV-M30) or to the PC by the software for the IV-H/IV-HG Series (IV-H1). ^8 This can be displayed on the intelligent monitor (IV-M30) or by software for the IV-H/IV-HG Series (IV-H1). ^9 Possible with both the color type and monochrome type ^10 This is for connection with the intelligent monitor (IV-M30) or software for the IV-H/IV-HG Series (IV-H1). ^*11 When attaching the sensor amplifier to a DIN rail, attach the sensor amplifier to a metal plate.

Keyence IV2-CP50 Keyence

€651,95

In stock, 19 units

Specifications

Model		IV2-CP50
Supported languages		English / Japanese / German / Chinese (Simplified) /Chinese (Traditional) / Korean / Italian / French / Spanish / Portuguese / Czech / Hungarian / Polish / Thai^*1
Display		5.7" TFT color LCD, 640 × 480 (VGA)
Backlight	Method	White LED
	Duration	Approx. 50000 hours (25°C 77°F)
Touch panel	Method	Analog resistive
	Actuating force	0.8 N or less
Indicators		PWR, SENSOR
Ethernet	Standard	100BASE-TX/10BASE-T^*2
	Connector	M12 4-pin connector^*2
Expanded memory		USB memory^*3
Rating	Power voltage	24 VDC ±10% (including ripple)
	Current consumption	0.3 A or less
Environmental resistance	Enclosure rating	IP40
	Ambient temperature	0 to +50°C 32 to 122°F (No freezing)
	Relative humidity	35 to 85% RH (No condensation) ^*4
	Drop resistance	1.3 m 4.3' onto concrete (2 times in an arbitrary direction)
	Vibration resistance	10 to 55 Hz; double amplitude 0.7 mm 0.03"; 2 hours in each of the X, Y, and Z directions
Material		Main unit case: PC, Power connector: Brass + Ni plating, Ethernet connector: Zinc + Ni plating / PA, USB connector cover: EDPM, Pen holder: PC, Adapter fixing hook: POM, LED lamp cover: PC, Mounting adapter: PC, Stylus: POM
Weight		Main unit: Approx. 450 g With wall mounting adapter and stylus attached: Approx. 485 g
^1 When connected to the IV2 Series. When connected to the IV Series, the supported languages are the same as the IV-M30. ^2 Dedicated for use in connecting to the IV2 Series and IV Series. ^3 Use only products recommended by KEYENCE. ^4 If the ambient operating temperature exceeds 40°C 104°F, use the product under conditions where the absolute humidity is 85% RH or less at 40°C 104°F.

Keyence IV2-G30F Keyence

€984,95

In stock, 15 units

Specifications

Model		IV2-G30F
Type		Learning/standard type
Tools	Available modes	Learning mode / Standard mode
	Standard mode built-in tools	Outline, Color area^1, Area^2, Edge pixels, Color average^1, Brightness average^2, Width, Diameter, Edge presence, Pitch, OCR, Color/brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge)
	Number of tools	Detection tools: 16 tools, position adjustment tool: 1 tool^*3
Switch settings (programs)		128 programs (when using SD card) / 32 programs (when not using SD card)
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT, SD
Image history	Number of storable images	1000 images ^*4
	Save conditions	Selectable between NG only, NG and OK near threshold^5, and All ^4
Image data transfer	Transfer destination	Selectable between SD card and FTP server
	Transfer format	Selectable between bmp, jpeg, iv2p, and txt
	Transfer conditions	Selectable between NG only, NG and OK near threshold^*5, and All
Analysis information	RUN display	Tools list (Judgment results, degree of similarity, or degree of similarity bar display) ^*6
	RUN information	Switchable between OFF, histogram, processing time, count, and output monitor Histograms: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGs Processing time: Processing time (latest, Max., Min., Ave.), Image capture interval (latest, Max., Min., Ave.) Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errors, Strobe errors Output monitor: ON/OFF status by output
Other functions	Image capture function	Image buffer, Image capture range, Digital zoom (2×, 4×), HDR, High gain, Color filter^1, White balance^1, Brightness correction
	Tool functions	Learning mode: Additional learning Standard mode: Mask outline, Masking function, Color extraction/exclusion^1, Color histogram function^1, Monochrome histogram function^*2, Scaling function
	Utilities	Failing sensor list, Failure hold, Test run, I/O monitor, Security settings, Simulator^*7
Input	Type	Switchable between non-voltage input and voltage input For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs	8 (IN1 to IN8)
	Function	IN1: External trigger, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Clear error, External master image registration, SD card save cancel
Output	Type	Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA, residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA, residual voltage of 2 V or less
	Number of outputs	8 (OUT1 to OUT8)
	Function	Enable by assigning optional functions Assignable functions: Total judgment (OK/NG), Run, Busy, Ready, Strobe, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card error
Ethernet	Standard	100BASE-TX/10BASE-T
	Connector	RJ45 8-pin connector
Network function		FTP client, SNTP client
Interface compatibility	Built-in Ethernet	EtherNet/IP™, PROFINET, TCP/IP non-procedure communication
	Communication unit	EtherCAT^Ⓡ, CC-Link, DeviceNet^Ⓡ, PROFIBUS, RS-232C^*8
Expanded memory		SD card (SD/SDHC) ^*9
Rating	Power voltage	24 VDC ±10% (including ripple)
	Current consumption	1.8 A or less (including communication unit and output load)
Environmental resistance	Ambient temperature	0 to +50°C 32 to 122°F (No freezing)
	Relative humidity	35 to 85% RH (No condensation)
Material		Main unit case: PC, Power connector: PA/POM, I/O connector: PA, Sensor head connector: Zinc + Ni plating/PA, Ethernet connector: Copper alloy + Ni plating, Main unit rear heat sink: Aluminum, Main unit rear DIN rail fixing tab: POM, Nameplate: PC
Weight		Approx. 330 g
^1 Color type only. ^2 Monochrome type only. ^3 Tools can be installed by programs. ^4 Saves to the sensor amplifier’s internal memory. The images saved to the sensor amplifier can be backed up to a USB memory stick inserted into the control panel (IV2-CP50) or to the PC where the software for the IV2 Series (IV2-H1) is being used. ^5 Learning mode only. ^6 Can also be displayed on the control panel (IV2-CP50) or the software for the IV2 Series (IV2-H1). ^7 Usable on the software for the IV2 Series (IV2-H1). ^8 When a communication unit (DL Series) is connected. ^*9 Use only products recommended by KEYENCE.

Keyence IV3-600CA Keyence

€2.731,95

In stock, 18 units

Specifications

Model		IV3-600CA
Type		Wide view
Installed distance		50 mm 1.97" or more ^*1
Tools	Available modes	Standard mode / Sorting mode
	Tool with standard mode	Learning, Outline, Color area ^2, Area ^3, Edge pixels, Color average ^2, Brightness average ^3, Width, Diameter, Edge presence, Pitch, OCR, Color prohibit ^*4, Brightness prohibit, Position adjustment, High-speed position adjustment (1-axis edge/2-axis edge), Blob count
	Number of tools	Total: 65 tools ^*5
Field of view		Installed distance 50 mm 1.97": 51 (H) × 38 (V) mm 2.01" (H) × 1.50" (V) to Installed distance 3000 mm 118.11": 2730 (H) × 2044 (V) mm 107.48" (H) × 80.47" (V)
Switch settings (programs)		128 programs (when using SD card) / 32 programs (when not using SD card)
Image receiving element	Type	1/2.9 inch color CMOS
	Number of pixels	1280 (H) × 960 (V)
Image history	Number of storable images	100 images ^*6
	Save conditions	Selectable between NG only, NG and OK near threshold ^7, and All ^6
Focus adjustment		Auto ^*4
Image data transfer	Transfer destination	Selectable between SD card, FTP server and SFTP server
	Transfer format	Selectable between bmp, jpeg, iv3p, and txt, and file names can be modified
	Transfer conditions	Selectable between NG only, NG and OK near threshold ^*8, and All
Exposure time		12 μs to 10 ms
Analysis information	RUN display	Tools list (Judgment results, degree of similarity, or degree of similarity bar display) ^*8
	RUN information	Switchable between OFF, histogram, processing time, count, and output monitor Histogram: Histogram, degree of similarity (Max., Min., Ave.), Number of OKs, Number of NGs Processing time: Processing time (latest, Max., Min., Ave.) Count: Trigger numbers, Number of OKs, Number of NGs, Trigger errors, Strobe errors Output monitor: ON/OFF status by output ^*8
Lights	Illumination	White LED
	Lighting method	Pulse lighting/ continuously lighting is switchable.
Other functions	Image capture function	Digital zoom (2×, 4×), HDR, High gain, Color filter ^2, White balance ^2, Brightness correction, AI capture
	Tool functions	Additional learning, Mask outline, Masking function, Color extraction/exclusion ^2, Color histogram function ^2, Monochrome histogram function ^*3, Scaling function
	Utilities	Failing sensor list, Failure hold, Test run, I/O monitor, Security settings (Two-factor password), Simulator ^*9, Additional FTP/SFTP Image Information, Multi-position adjustment, Multi-master image registration, High-speed program switching, Auto program switching, Auto setting backup/restore, Threshold changing in RUN
Indicators		OUT, TRIG, STATUS, LINK/ACT, SD
Input	Type	Switchable between non-voltage input and voltage input For no-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 30 V, ON voltage 18 V or higher, OFF current 0.15 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs	6 ports, 3 ports are selectable as IN/OUT
	Function	IN1: External trigger, IN2, IN3, I/O1 to I/O3: Enable by assigning optional functions Assignable functions: Program switching, Clear error, External master image registration, SD card save cancel
Output	Type	Photo MOS relay output, N.O./N.C. Switchable Maximum rating 30 V 50 mA, residual voltage 1.5 V or less ^*10
	Number of outputs	6 ports, 3 ports are selectable as IN/OUT
	Function	Enable by assigning the optional functions Assignable functions: Total judgment (OK/NG), Run, Busy, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Error, SD card error, Variety discrimination result, Master judgment result
Power/I/O	Connector	M12 12 pin A code Male connector
	PoE	PoE power Class 3/4/6 ^*11
Ethernet	Standard	1000BASE-T/100BASE-TX
	Connector	M12 8 pin X code Female connector
Network function		FTP client, SFTP client
Interface compatibility	Built-in Ethernet	EtherNet/IP™, PROFINET ^*12, TCP/IP non-procedure communication
Expanded memory		microSD card (microSD/microSDHC) ^*13
Ratings	Power voltage	24 VDC +25%/-20% (including ripple) ^*14
	Current consumption	3.3 A or less (without the AI Lighting unit, and including the output load) 1.8 A or less (AI Lighting unit, and including the output load) ^*15
Environmental resistance	Enclosure rating	IP67 ^*16
	Ambient temperature	0 to +50°C 32 to 122°F (No freezing) ^*17
	Relative humidity	35 to 85% RH (No condensation)
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours in each of the X, Y, and Z directions ^*18
	Shock resistance	500 m/s² 1640'/s², 3 times in each of the 6 directions ^*18
Material		Main unit case: Aluminum die-casting/PBT/TPU Indicator light cover: TPU Ethernet connector: Aluminum die-casting/LCP Front cover: Acrylic (hard coating) Power connector: Aluminum die-casting/LCP Nameplate: PET Water proof cap for the Power connector: PC+ABS alloy Water proof cap for the Ethernet connector: PC
Weight		Approx. 300 g 10.59 oz (without the AI Lighting unit) Approx. 495 g 17.47 oz (with the AI Lighting unit)
^1 Removing the polarizing filter is recommended when used at distances of 3 m 9.8' or more. ^2 Color type only. ^3 Monochrome type only. ^4 The focusing position can be automatically adjusted at the time of installation. Disabled during operation. The focusing position can be registered by programs. ^5 Tools can be installed by programs. This is the number of detection tools and position adjustment tools. Up to 64 detection tools can be set. The number of detection tools in Sorting mode are eight tools. ^6 Saves to the sensor’s internal memory. The images saved to the sensor can be backed up to a USB memory stick inserted into the control panel (IV3-CP50) or to the PC where the software for the IV3 Series (IV3-H1) is being used. ^7 Learning tool only. ^8 Can also be displayed on the control panel (IV3-CP50) or the software for the IV3 Series (IV3-H1). ^9 Usable on the software for the IV3 Series (IV3-H1). ^10 Make sure to keep a total of each output with 120 mA or less. ^11 For a PoE power supply device, IEEE802.3at power class 4 or higher is recommended when using the AI Lighting unit, and IEEE802.3bt power class 6 or higher is recommended when the AI Lighting unit is not used. When using PoE operation may be restricted due to power limitation. ^12 Conformance Class B, applicable protocol: LLDP, SNMP. ^13 Use only products recommended by KEYENCE. ^14 When using the OP-88656 (10 m 32.8'), the power voltage is 24 V DC +25%/-10% (including ripple). ^15 The peak current is designed to be smaller if the AI Lighting unit is mounted. The peak current is greater if the AI Lighting unit is not mounted. ^16 Except when the polarizing filter (OP-88640/OP-88641/OP-88644/OP-88645) is mounted. ^17 For situations where the operating ambient temperature will exceed 40°C 104°F, follow KEYENCE’s specified heat dissipation measures to ensure the case temperature does not exceed the rated maximum temperature (65°C 149°F). Check the instruction manual for more information. ^18 Except when the dome attachment (IV3-D10) is mounted.

Keyence OP-88648 Keyence

€196,95

Only 8 units left

Specifications

Model				OP-88648
Type				Sensor head to amplifier cable
Length				2 m 6.6'
Weight				Approx. 100 g

Keyence FW-H10R Keyence

€309,95

Only 5 units left

Specifications

Model		FW-H10R
Type		Long range
Detecting area		150 to 1000 mm 5.9" to 39.4"^*1
Response speed		1,000 ms
Temperature characteristics		0.06% of F.S./°C^*2
Indicator lamp		Operation indicator (orange) x1 (Turns on when the target is within the detecting range.)
Dimensions		M18 x P1, Length= 104 mm 4.09"
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +70 °C -13 to 158 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material		Brass-nickel plating, PBT, Polyurethane, Polyamide resin
Accessories		M18 nut: 2, Head cable: 2 m 6.6', Standard Mounting Bracket (FW-B01)
Weight		Approx. 106 g
^1 Less stable zones of approx. 2% of F.S. exist at both ends of the detecting range. ^2 The errors for the indicated value at 25°C 77°F.

Keyence FU-E40 Keyence

€236,95

In stock, 11 units

Specifications

Model		FU-E40^*1
Optical axis diameter (Standard target to be detected)		40 × 3 mm1.575" × 0.118"
Fibre unit length		2 m78.74" free-cut
Fibre unit diameter		ø2.2×2
Minimum bend radius		R2 mm0.079" Tough-Flex
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 30 g
^*1 For details on the detecting distance, see the fiber amplifier catalog.

Keyence FU-E11 Keyence

€156,95

Only 3 units left

Specifications

Model		FU-E11
Type		Area thrubeam
No. of beam axes		11 × 2 mm0.433" × 0.079", 11 × 1 mm0.433" × 0.039" (when the 1.0 mm0.039" slit is attached), 11 × 0.5 mm0.433" × 0.02" (when the 0.5 mm0.02" slit is attached)
Fibre unit length		2 m78.74" free-cut
Fibre unit diameter		ø2.2
Minimum bend radius		R2 mm0.079"
Minimum detectable object		Opaque material with a diameter of 0.2 mm0.008"^*1
Tightening torque		0.15 Nm
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
Material		Main unit case : polybutylene terephthalate, screw mounting seat : SUS304, lens : norbornene plastic, core fiber : acrylic, fiber sheath : polyethylene
Accessories		Mounting screws (M2 × 6), nuts (M2, t = 1.2), fiber cutter, slit (0.5 mm or 1.0 mm width)
Weight		Approx. 20 g
^*1 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence FU-69X Keyence

€116,95

Only 7 units left

Specifications

Model		FU-69X^*1
Size		M3
Fibre unit length		1 m39.37" cannot be cut
Minimum bend radius		R4 mm0.157" high-flex
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +70 °C -40 to 158 °F
Weight		Approx. 3 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence OP-84327 Keyence

€113,95

Only 8 units left

Specifications

Model				OP-84327
Type				Head mounting bracket
Applicable product				GT2-H32/GT2-H50
Note				Sold separately

Keyence FU-57TZ Keyence

€121,95

Only 7 units left

Specifications

Model		FU-57TZ^*1
Optical axis diameter (Standard target to be detected)		ø0.5 mm0.02"
Beam emitting direction		Side
Fibre unit length		1 m39.37" free-cut
Fibre unit diameter		ø1.0
Minimum bend radius		R2 mm0.079" Tough-Flex
Minimum detectable object		Object with a diameter of 0.005 mm0.0002"^*2
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 5 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence OP-77679 Keyence

€106,95

Only 8 units left

Specifications

Model				OP-77679
Applicable product				GT Series/GT2 Series
Note				This is a flat-plate-type contact (sold separately). This contact can be used to perform detections using the peaks of the bumps of the target.

Keyence FU-44TZ Keyence

€113,95

In stock, 11 units

Specifications

Model		FU-44TZ^*1
Beam emitting direction		Top
Fibre unit length		1 m39.37" free-cut
Fibre unit diameter		ø1.0×2
Minimum bend radius		R2 mm0.079" Tough-Flex
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 3 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence FU-35FG Keyence

€126,95

Only 7 units left

Specifications

Model		FU-35FG^*1
Size		M3
Detection arrangement		Coaxial
Fibre unit length		1 m39.37" free-cut
Fibre unit diameter		ø1.3×2
Shape		Straight
Minimum bend radius		R10 mm0.394" , stainless
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 15 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Keyence FU-21X Keyence

€121,95

Only 6 units left

Specifications

Model		FU-21X^*1
Size		M3
Detection arrangement		Coaxial
Fibre unit length		50 cm19.685" cannot be cut
Shape		Straight
Minimum bend radius		R25 mm0.984"
Minimum detectable object		Gold wire with a diameter of 0.005 mm0.0002" ^*2
Environmental resistance	Ambient temperature	-40 to +70 °C -40 to 158 °F
Weight		Approx. 4 g
^1 For details on the detecting distance, see the fiber amplifier catalog. ^2 The minimum detectable object is the value when the detecting distance and sensitivity have been set to their optimal state.

Previous Page 2 / 75Next