Machine Vision Systems

Keyence OP-88093 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-88551 Keyence

€411,95

Only 9 units left

Specifications

Model				OP-88551
Type				Sensor head to amplifier cable
Length				20 m 65.6'
Weight				Approx. 760 g

Keyence NQ-EP4L Keyence

€369,95

Only 5 units left

Specifications

Model		NQ-EP4L
Network Specifications	Compatible Networks	EtherNet/IP™, Modbus/TCP
	Communication Speed	10 Mbps/100 Mbps
	Connector	M8 4-pin female A-code
Power Supply Specifications	Connector Type	Power supply port IN: M8 4-pin male A-code Power supply port OUT: M8 4-pin female A-code
	Power Voltage	18 to 30 VDC (During IO-Link communication: 20.4 V to 28.8 V)
	Allowable Current	V1 and V2: max. 4 A each
	Current Consumption	V1: max. 110 mA V2: max. 115 mA
Sensor Connection Specifications	Connector Type	M12 5-pin female A-code
	V1 Power Supply Capacity	-
	V2 Power Supply Capacity	Ports 1 to 4: 4 A in total
IO-Link Specifications	Number of Connectable Devices	4
	Compliant Standards	Ver1.1
	Transmission Speed	COM1: 4.8 kbps COM2: 38.4 kbps COM3: 230.4 kbps
	Port type	Ports 1 to 4: Class A^*1
	Process Data Size	Input: Max. 32 bytes/Output: Max. 32 bytes
Digital Input (DI) Specifications	Number of Inputs	Max. 8 (when using DI mode)
	Input Type	PNP
	ON Voltage/ON Current	11 V or higher/2 mA or higher
	OFF Voltage/OFF Current	Less than 5 V/less than 1.5 mA
	Input Current	Pin 2: approx. 7 mA, Pin 4: approx. 12 mA
Digital Output (DO) Specifications	Number of Outputs	Max. 4
	Output Type	PNP
	Maximum Load Current	Each port max. 0.5 A
	Short-Circuit Protection Circuit	Yes
	Leakage Current	0.1 mA or lower
	Residual Voltage	1 V or lower
Environmental resistance	Enclosure rating	IP65/IP67/IP69K
	Ambient temperature	-40°C to +70°C -40°F to +158°F (no freezing)
	Vibration resistance	5 to 150 Hz/20 G/10 sweeps each in X, Y, and Z axes
	Shock resistance	15 G/11 ms/3 times each in X, Y, and Z axes
Case Material		Housing: PA6-GF30 Connector: SUS303
Weight		Approx. 190 g 6.70 oz
^*1 When using Class B, V1 and V2 each require a power supply.

Keyence LV-S62 Keyence

€263,95

Only 8 units left

Specifications

Model		LV-S62
Type		Parallel light area
FDA (CDRH) Part 1040.10		Class 1 Laser Product
IEC 60825-1
Light source		Visible red semiconductor laser, Wavelength: 660 nm
Detecting distance	MEGA	12 m (6 m) 39.4' (19.7')^*1
	ULTRA	10 m (5 m) 32.8' (16.4')^*1
	SUPER	8 m (3.5 m) 26.2' (11.5')^*1
	TURBO	5 m (2 m) 16.4' (6.6')^*1
	FINE	2.5 m (0.7 m) 8.2' (2.3')^*1
	HSP	-
Environmental resistance	Ambient temperature	-10 to +50 °C 14 to 122 °F (No freezing)
Material	Case	Glass reinforced plastic
	Lens cover	Acrylic
	Reflective mirror	Polycarbonate, acrylic
Weight		Approx. 65 g
^*1 Numbers enclosed in parentheses are the detecting distance for small beam spot.

Keyence GV-H45L Keyence

€348,95

Only 7 units left

Specifications

Model			GV-H45L
Type			Short-range
Light source			Visible semiconductor laser, Wavelength: 655 nm
Laser class	FDA (CDRH) Part 1040.10		Class 1^*1 (220 µW)
	IEC 60825-1		Class 1 (220 µW)
	JIS C6802
Detection distance (Amplifier display )			20 to 45 mm 0.79" to 1.77" (250 to 0)^*2)
Possible display range			259 to -34
Standard detection deviation			0.5 mm 0.02"
Spot diameter			Approx. ø0.1 mm ø0.004" (Detection distance 45 mm 1.77")
Operation status indicators			Control output: Red LED/Laser radiation emission indicator: Green LED/1 spot indicator: Green LED
Environmental resistance	Enclosure rating		IP67
	Operating ambientluminance	Incandescent lamp	5000ℓx
		Sunlight	10000ℓx
	Ambient temperature		-10 to +50 °C 14 to 122 °F (No freezing)
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z axis
Material			Housing material: PBT, Display: Polyarylate, Metal: SUS304, Lens cover: Glass, Cable: PVC
Weight			Approx. 120 g^*3
^1 The laser classification for FDA (CDRH) is implemented based on IEC 60825-1 in accordance with the requirements of Laser Notice. ^2 General guideline for amplifier display values relative to detection distance (when distance display mode is set to normal). ^*3 Including 2 m 6.6' connector cable (3 m 9.8' cable for GV-H1000)

Keyence FI-CF4 Keyence

€0,00

Sold Out

Specifications

Model		FI-CF4
Type		Pipe type
Main unit		FI-C40F
Detection principle		Refractive index (surface light source)
Rated concentration range		Brix: 0–40% (nD: 1.32500–1.41000)
Display method		Status indicator light
Display range		Brix: 0–50%
Supported fluids		Non-corrosive aqueous solutions (such as water-soluble coolants, mold release agents, etc.)^*1
Supported fluid temperature		0–70°C 32–158°F (no freezing)
Connection diameter		NPT1 1/2
Rated pressure range		1.0 MPa or less
Pressure resistance		2.0 MPa
Display resolution		Brix: 0.01/0.1% (default value: 0.1) (nD: 0.00001)
Response time		1.0 s / 2.5 s / 5.0 s / 10.0 s / 30.0 s / 60.0 s / 120.0 s / 200.0 s
Measurement accuracy		Brix: ±0.2%^2^3 (nD: ±0.0003)
Concentration unit		Brix nD^*4
Temperature measurement accuracy		±1.0°C 1.8°F^*2
Power supply	Current consumption	25 mA or less
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient temperature	–10 to +60°C 14 to +140°F (no freezing)
	Relative humidity	35–85% RH (no condensation)
	Vibration resistance	10–500 Hz; Power spectral density: 0.816 G²/Hz; X, Y and Z directions
	Shock resistance	100 m/s² (approx. 10 G), 16 ms pulses, 1000 times each for X, Y and Z directions
Material	Liquid end materials	Body: SCS16A; Gasket: FKM
	Other materials	Body: SUS304; PPS indicator light: PPSU / TPU / PBT Cable: PVC
Weight		Approx. 1360 g 47.97 oz
^1 Use water as the solvent, and use materials that are soluble in water. If the particles are not water soluble, such as with slurry, the refractive index may not change. ^2 This is the guaranteed value from verification performed at KEYENCE inspection facilities. Measurement error may occur depending on the type, condition and temperature of the fluid used by the customer, as well as other factors. ^3 This is the value obtained when sucrose solution is used in a constant 20°C 68°F environment, and absolute error and repeatability is taken into account. ^4 When using solutions other than sucrose solutions, concentration can be adjusted via span adjustment.

Keyence NE-Q05 Keyence

€370,95

Only 5 units left

Specifications

Model				NE-Q05
General specifications	Current consumption.			180 mA
	Power voltage			24 VDC ± 10%
	Operating ambient temperature			0 to +50°C 32 to 122°F ^*1 (no freezing)
	Operating ambient humidity			10 to 95%RH (no condensation)
	Storage ambient temperature			-20 to +70°C -4 to 158°F
	Operating environment			Minimal amount of dust and corrosive gas present
	Operating altitude			2000m or less
	Noise immunity			1,500 Vp-p, pulse width: 1 µs, 50 ns (by way of a noise simulator)
	Withstand voltage			1,500 VAC for 1 minute between the power supply terminal and the communication terminal and between all the external terminals and the case
	Insulation resistance			50 MΩ or more (tested with a 500 VDC megger, between the power supply terminal and the communication terminal and between all the external terminals and the case)
	Shock resistance			Acceleration: 150 m/s², operating time: 11 ms, 2 times in each of the X, Y, and Z directions
	Overvoltage category			I
	Pollution degree			2
	Vibration resistance	Intermittent vibration	Frequency: 10 to 57 Hz	Amplitude: 0.075 mm^*2
			Frequency: 57 to 150 Hz	Acceleration: 9.8 m/s²^*2
		Continuous vibration	Frequency: 10 to 57 Hz	Amplitude: 0.035 mm^*2
			Frequency: 57 to 150 Hz	Acceleration: 4.9 m/s²^*2
	Weight			Approx 180g
Function/performance specifications	Data transfer speed			10 Mbps, 100 Mbps, automatic support for full duplex and half duplex modes
	MDI/MDI-X automatic switching function			Provided
	Auto-negotiation function
Communicationspecifications	MAC address retention			300 s
Function/performance specifications	Upper limit for the number of MAC addresses that can be registered			2048
	QoS function			Priority control of EtherNet/IP™ cyclic data
	PoE function			None
Communicationspecifications	Switching type			Store and forward method
	Metal cable	Flow control		Half duplex: back pressure, full duplex: conforms to IEEE802.3x; pose packets are used to perform flow control
^1 This is regulated according to the temperature below the control panel unit. ^2 Conforms to JIS B 3502 IEC61131-2, 10 times respectively in the X, Y, and Z directions, 80 minutes

Keyence FU-77TG Keyence

€148,95

Only 10 units left

Specifications

Model		FU-77TG^*1
Optical axis diameter (Standard target to be detected)		ø1.13 mm 0.04"
Size		M4
Fibre unit length		1 m 3.28', cut not allowed.
Shape		Hex-shaped
Minimum bend radius		R10 mm R0.39", Stainless Steel
Environmental resistance	Ambient temperature	-40 to +50 °C -40 to 122 °F
Weight		Approx. 43 g
^*1 For details on the detecting distance, see the fiber amplifier catalog.

Keyence CA-LMH15 Keyence

€0,00

Sold Out

Specifications

Model				CA-LMH15^*1
Optical magnification				x1.5
Shape				Standard
Compatible image sensor size				2/3"
Field of view (at reference magnification)				1/3": 2.4 × 3.2 mm 0.09" × 0.13" 1/2": 3.2 × 4.2 mm 0.13" × 0.17" 2/3": 4.4 × 5.8 mm 0.17" × 0.23"
F-stop range (aperture)				11.9
Ambient temperature/humidity range				0 to 50°C 32 to 122°F, 35 to 80% RH (no condensation)
WD				110.0 mm 4.33"^*2
TV distortion				0.00% (2/3")
Depth-of-field				0.4 mm 0.02"^*3
Mount				C-mount
Resolution				5.3 µm 0.21 Mil^*4
Weight				Approx. 110 g
^1 Depending on factors such as the installation orientation and the vibrations of the environment, consider reinforcing the installation such as by implementing countermeasures to hold the lens in place. For information on the locations to hold the lens in place, see the installation examples. The above values were calculated according to optical design values. Actual values for individual lenses will differ according to precision of assembly. ^2 WD indicates the distance from the tip of the lens to the workpiece. ^3 The depth of field is a theoretical value calculated with a circle of least confusion of 40 µm 1.57 Mil. ^4 The smallest resolvable feature able to be detected under 550 nm wavelength light.

Keyence FD-ECH10 Keyence

€2.242,95

Only 5 units left

Specifications

Model			FD-ECH10
Pipe size	Outer diameter of pipe		ø10 0.39"
	Installable range		10.0 0.39" ± 0.15 mm 0.01"
	Pipe materials		Polyurethane, nylon, PFA,^1 other^2
Supported gases			Air, nitrogen, argon, and other gases^*3
Supported gas temperature			−10°C to +60°C 14 to 140°F
Operating pressure range			0 to 0.75 MPa (upper limit depends on pipe specifications)
Flow rate detection principle			Ultrasonic transmission time difference method
Rated flow rate	(volume flow rate)		120 L/min 4.24 CFM * Initial display
	(20°C 68°F, atmospheric pressure conversion)	Gas at 20°C 68°F, 0.2 MPa	360 L/min 12.7 CFM
		Gas at 20°C 68°F, 0.4 MPa	600 L/min 21.2 CFM
		Gas at 20°C 68°F, 0.6 MPa	840 L/min 29.7 CFM
Repeatability			Response time 250 ms: ±2.5% of F.S.^4^5
Display resolution	Instantaneous flow		0.1/1 L/min
	Accumulated flow		0.1/1/10/100/1000 L
Display method			Output indicator
Environmental resistance	Enclosure rating		IP65 (IEC60529)
	Ambient temperature		−10°C to +60°C 14 to 140°F (no freezing)
	Relative humidity		35%RH to 85%RH (no condensation)
	Vibration resistance		10 to 500 Hz, power spectral concentration: 0.816 G²/Hz, XYZ axes
	Shock resistance		100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Sensor unit		PBT/PAR/iron
	Sensor surface		Special rubber
Weight			Approx. 114 g 4.02 oz
^1 Use PFA tubes in an environment with a temperature of 40°C 104°F or less. ^2 Resin tubes that transmit ultrasonic waves. ^3 Gases that transmit ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^4 Accuracy improves with longer response times. As a rule, this is by a proportion of √(250 ms/response time)x. ^*5 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the condition and type of pipes as well as the temperature and type of gas.

Keyence BT-WUC84GA Keyence

€0,00

Sold Out

Specifications

Model		BT-WUC84GA
Dedicated AC adapter specifications	Input side	100 to 240 VAC, 50/60 Hz
	Output side	16 VDC, Max. 3.75 A
Dimensions	Dedicated AC adapter specifications	102.5 x 42.5 x 28 mm 4.04" x 1.67" x 1.1" (not including the cable)
Weight		Approx. 250 g
Environmental resistance	Ambient temperature	0 to +40 °C 32 to 104 °F (No freezing)
	Relative humidity	20 to 85 % RH (No condensation)
	Storage temperature	-20 to +60 °C -4 to 140 °F (No freezing)
	Storage relative humidity	20 to 85 % RH (No condensation)
Accessory		AC adapter (OP-88149)^*1
Dimensions		93.6 × 97.1 × 327 mm
Weight		Approx. 785 g
^*1 A separate AC cable is required.

Keyence AP-31PA Keyence

€654,95

Only 1 unit left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence ER-NH028 Keyence

€0,00

Sold Out

Specifications

Model		ER-NH028
Cable		Standard
Stable detection range		0 to 0.6 mm 0 to 0.02" ^1 ^2
Maximum operating distance		1.2 mm 0.05" ^1 ^3
Hysteresis distance		Adjustable
Repeatability		1 μm 0.04 Mil ^1 ^4
Detectable object		Magnetic metal, Non-magnetic metal ^*5
Standard detectable object (Iron, t = 1 mm 0.04")		5 × 5 mm 0.20" × 0.20"
Temperature characteristics		±10% or less of detecting distance at +25°C +77°F (0 to +50°C 32°F to 122°F) ±15% or less of detecting distance at +25°C +77°F (-10 to 0°C 14°F to 32°F, +50 to +60°C 122°F to 140°F) (For ER-NH028/038/035F/028U) -10 to +15 % or less of detecting distance at +25°C+77°F (0 to +50°C 32°F to 122°F), -15 to +20 % or less of detecting distance at +25°C +77°F (-10 to 0°C 14°F to 32°F, +50 to +60°C 122°F to 140°F) ^1 ^6
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient temperature	-10 to +60°C 14°F to 140°F (no freezing)
	Relative humidity	Up to 85% RH (No condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	1000 m/s² 3280.8 ft/s² (100 G), 10 times in each of the X, Y, and Z directions
Material	Detection surface	Epoxy resin
	Case	SUS304
	Cable	PVC
	Sensor head connector	PA66, polycarbonate
	Accessories	―
Accessories
Weight		Approx. 30 g 1.06 oz
^1 The stable detection range, maximum operating distance, repeatability, and temperature characteristics are values for when the operation mode is set to “Normal” using a standard detection object. ^2 The range where 2-point adjustment is normally possible with a detectable object placed within this range and with no detectable object. The stable detection range becomes narrower when in magnetic metal / non-magnetic metal mode. ^3 The maximum distance of the stable detection range and the distance that can be detected under constant temperature when 2-point adjustment is used with no detectable object and the set value is set appropriately. ^4 Values obtained by converting the fluctuation range of the detection amount to the detecting distance under a constant environment using KEYENCE default settings. ^5 Detecting distance varies according to the material and size. See the characteristic diagrams for details. ^6 The value when using the 2-point adjustment function at a distance of 25% of the stable detection range with no detectable object and a standard detectable object at a distance of 50% of the stable detection range.

Keyence OP-88883 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SH-303A Keyence

€632,95

Only 4 units left

Specifications

Model		SH-303A
Type		Standard Shielded Cylindrical
Shape		ø3.8×18 Cylindrical
Detectable object		Ferrous metal (see Characteristics for nonferrous metals)
Standard target (iron, t=1 mm 0.04")		5 x 5 mm 0.20"^*1
Stable detecting range		0 to 0.8 mm 0.03"
Maximum detecting distance		2 mm 0.08"
Repeatability		0.001 mm 0.00004"^*1
Hysteresis		0.05 mm 0.002"^*1
Temperature characteristics		0.3%/°C^*1
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Weight		Approx. 35 g
^*1 Above values obtained when the detecting distance is set at 50% of the maximum stable detecting distance.

Keyence BZ-H5XT Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence VT-PW10N Keyence

€0,00

Sold Out

Specifications

Model				VT-PW10N
Type				10" widescreen protective sheet
Applicable product				for VT5-W10
Number included				Set of 5 sheets
Note				white, without logo

Keyence FD-ECH6 Keyence

€504,95

Only 6 units left

Specifications

Model			FD-ECH6
Pipe size	Outer diameter of pipe		ø6 0.24"
	Installable range		6.0 0.24" ± 0.15 mm 0.01"
	Pipe materials		Polyurethane, nylon, PFA,^1 other^2
Supported gases			Air, nitrogen, argon, and other gases^*3
Supported gas temperature			−10°C to +60°C 14 to 140°F
Operating pressure range			0 to 0.75 MPa (upper limit depends on pipe specifications)
Flow rate detection principle			Ultrasonic transmission time difference method
Rated flow rate	(volume flow rate)		40 L/min 1.41 CFM * Initial display
	(20°C 68°F, atmospheric pressure conversion)	Gas at 20°C 68°F, 0.2 MPa	120 L/min 4.24 CFM
		Gas at 20°C 68°F, 0.4 MPa	200 L/min 7.06 CFM
		Gas at 20°C 68°F, 0.6 MPa	280 L/min 9.88 CFM
Repeatability			Response time 250 ms: ±2.5% of F.S.^4^5
Display resolution	Instantaneous flow		0.01/0.1/1 L/min
	Accumulated flow		0.01/0.1/1/10/100 L
Display method			Output indicator
Environmental resistance	Enclosure rating		IP65 (IEC60529)
	Ambient temperature		−10°C to +60°C 14 to 140°F (no freezing)
	Relative humidity		35%RH to 85%RH (no condensation)
	Vibration resistance		10 to 500 Hz, power spectral concentration: 0.816 G²/Hz, XYZ axes
	Shock resistance		100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Sensor unit		PBT/PAR/iron
	Sensor surface		Special rubber
Weight			Approx. 102 g 3.60 oz
^1 Use PFA tubes in an environment with a temperature of 40°C 104°F or less. ^2 Resin tubes that transmit ultrasonic waves. ^3 Gases that transmit ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^4 Accuracy improves with longer response times. As a rule, this is by a proportion of √(250 ms/response time)x. ^*5 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the condition and type of pipes as well as the temperature and type of gas.

Keyence SV-020L2 Keyence

€1.459,95

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-88996 Keyence

€0,00

Sold Out

Specifications

Model				OP-88996
Type				Connection Cable
Cable end				M12 female 8-pin - M12 male 5-pin
Length				10 m 32.8'
Material				cable: Chemical-resistant PVC connector: PBT

Keyence BT-OCR1 Keyence

€672,95

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence EM-014P Keyence

€0,00

Sold Out

Specifications

Model		EM-014P
Type		Shielded
Shape		M14 Threaded
Detecting distance		4.0 mm 0.16" ±10%
Detectable object		Ferrous metals (see Characteristics for non-ferrous metals)
Standard target (iron, t=1 mm 0.04")		15 x 15 mm 0.59" x 0.59"
Hysteresis		10% max. of detecting distance
Response frequency		1.2 kHz
Operation mode		N.O.
Temperature characteristics		±10% max. of detecting distance at +23°C 73.4°F, within -10 to +70°C 14 to 158°F
Display indicator		Red LED
Output		PNP
Control output		PNP: 200 mA (30 V) max., Residual voltage: 1 V max.
Housing		Cr-plated brass
Rating	Power voltage	10.8 to 30 VDC, Ripple (P-P) 10 % or less^*1
	Current consumption	20 mA or less
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +80 °C -13 to 176 °F (No freezing)
	Relative humidity	35 to 95 % RH (No condensation)
Weight		Approx. 60 g (including nuts and 2-m 6.6' cable)
^*1 Make sure that the power voltage stays within 10.8 V to 30 V even if it is affected by ripple effects.

Keyence PJ-V91 Keyence

€374,95

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87463 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.