6 digital outputs Source connection 2-wire connections GND for signal supply Integrated output protection 1-wire connection type with 6-pin terminal block OSP mode The module is equipped with 6 outputs for 1 or 2-wire connections. The X20 6-pin terminal block can be used for universal 1-line wiring. 2-line wiring can be implemented using the 12-pin terminal block. The module is designed for source output wiring.
Integrated exchangeable microfuse Monitoring of the fuse Potential for routing as needed The potential distributor module provides 12x 24 VDC (from the internal I/O supply) on the terminal connections and opens up additional wiring possibilities for actuators and sensors. The module is equipped with a replaceable microfuse between the 24 VDC potential on the terminal block and the X20 system I/O supply. The function of the fuse is monitored.
Integrated exchangeable microfuse Monitoring of the fuse Potential for routing as needed The potential distributor module provides 12x ground (from the internal I/O supply) on the terminal connections and opens up additional wiring possibilities for actuators and sensors. The module is equipped with a replaceable microfuse between the GND potential on the terminal block and the X20 system I/O supply. The function of the fuse is monitored.
RS485/RS422 interface for serial, remote connection of complex devices to the X20 system Integrated terminating resistor In addition to the standard I/O, complex devices often need to be connected. The X20CS communication modules are intended precisely for cases like this. As normal X20 electronics modules, they can be placed anywhere on the remote backplane.
X20 analog input module, 4 inputs, ±10 V or 0 to 20 mA / 4 to 20 mA, 13-bit converter resolution, configurable input filte
4 analog inputs Either current or voltage signal possible 16-bit digital converter resolution Simultaneous input conversion Very fast conversion time The module is equipped with 4 inputs with 16-bit digital converter resolution. It is possible to select between the current and voltage signal using different terminals.
8 digital outputs Source connection 1-wire connections Integrated output protection The module is equipped with 8 outputs for 1-wire connections and designed for source output wiring.
2x outputs (H bridge) with PWM control and 24 to 39 VDC ±25% supply 3 A nominal current (3.5 A max current) 15 Hz to 50 kHz frequency, 16-bit Frequency mode with 10 to 6553.5 Hz or 1 to 655.35 Hz resolution. PWM resolution, 15-bit + sign, minimum 10 ns Configurable dither 2x 2 inputs 24V, can be configured as AB Sink connection 1-wire connections The motor bridge module is used to control 2 DC motors with a nominal voltage of 24 to 39 VDC ±25% at a nominal current up to 3 A. The module can be reconfigured and used in current controller mode for controlling inductive loads. The module is also equipped with 4 digital inputs, which can be used as incremental counters. Each motor is controlled with a full-bridge (H-bridge). This enables the motors to be moved in both directions.
Intel Atom 1.0 GHz processor with an additional I/O processor Onboard Ethernet, POWERLINK with poll response chaining and USB 3 slots for modular interface expansion CompactFlash as removable application memory 256 MB DDR2-SDRAM Controller redundancy possible Fanless The X20CP3585 controller is based on an Atom processor clocked at 1 GHz and equipped with 256 MB DDR2 SDRAM. USB, Ethernet, POWERLINK and removable CompactFlash are all included as standard features. A Gigabit Ethernet interface is a standard feature. For even more real-time network performance, the onboard POWERLINK interface supports poll response chaining mode (PRC). The controller is equipped with 3 slots available for X20 communication modules. Various bus and network systems can easily be integrated into the X20 system through the use of communication modules.
Intel x86 400 MHz compatible with integrated I/O processor Ethernet, POWERLINK with poll-response chaining and onboard USB 1 slot for modular interface expansion 30 digital inputs/outputs and 2 analog inputs integrated in the device 2 GB onboard flash drive 256 MB DDR3 SDRAM Fanless No battery Backed-up real-time clock The X20 Compact controller series is characterized by 3 integrated I/O modules. The device is equipped with 30 different digital inputs/outputs and 2 analog inputs. 1 analog input can be used for Pt1000 resistance temperature measurement. The X20CP1382 is equipped with an Intel x86 400 MHz compatible processor, 256 MB RAM and 2 GB built-in flash drive. The FRAM for storing remanent variables has 32 kB available. A fanless and battery-free design ensures maintenance-free operation. The controller is equipped with Ethernet, 2x USB and an RS232 interface. In addition, POWERLINK and CAN bus are available as integrated interfaces. For additional fieldbus connections, each controller can be expanded with an interface module from the X20 standard portfolio.
Intel x86-based, 100 MHz-compatible CPU with integrated I/O processor Onboard Ethernet, POWERLINK and USB 1 slot for modular interface expansion CompactFlash as removable application memory Fanless The Intel x86-based, 100 MHz-compatible X20CP1483 represents the entry-level X20 controllers. With an optimum price/performance ratio, it has the same basic features as all of the larger controllers. Onboard Ethernet and USB are standard. In addition, the controller has a POWERLINK connection for hard real-time communication. Another slot is available for an additional interface module to increase flexibility. The only difference between the two variants X20CP1483 and X20CP1483-1 is the size of the SDRAM.
POWERLINK for real-time Ethernet communication Integrated hub for efficient cabling Configurable ring redundancy The interface module can be used to expand the X20 CPU for specific applications. It is equipped with an POWERLINK interface. The interface has two RJ45 sockets. Both connections lead to an integrated hub. This makes it easy to create daisy-chain connections using POWERLINK.
Hub expansion module 2x hub 100 BASE-TX The POWERLINK bus controller X20BC8083 and the stand-alone hubs X20HB8880 and X20HB8815 are equipped with a modular hub expansion. An additional 1 or 2 slots are available, depending on the bus base used. The X20HB2880 hub expansion module can be operated in these slots. The status of the module and network are indicated by LEDs
Feed for X2X Link and internal I/O supply Electrical isolation of feed and X2X Link supply Redundancy of X2X Link supply possible by operating multiple supply modules simultaneously The supply module is equipped with a feed for the X2X Link as well as the internal I/O supply.
Tool-free wiring using push-in technology Simple wire release using a lever Labeling option for each terminal connection Plain text labeling possible Access for standard test probes Customized coding possible This terminal block is used to wire the X20 SafeIO modules with 12 connections.
12 digital outputs Source connection 1-wire connections Integrated output protection The module is equipped with 12 outputs for 1-wire connections. The module is designed for source output wiring.
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 72A (nom.; in-line) - Rated power 37kW (nom.; 400Vac; in-line) / 50HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE72-600-70
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 60A (nom.; in-line) - Rated power 30kW (nom.; 400Vac; in-line) / 40HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE60-600-70
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 45A (nom.; in-line) - Rated power 22kW (nom.; 400Vac; in-line) / 30HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE45-600-70
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 37A (nom.; in-line) - Rated power 18.5kW (nom.; 400Vac; in-line) / 25HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE37-600-70
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 30A (nom.; in-line) - Rated power 15kW (nom.; 400Vac; in-line) / 20HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE30-600-70
Soft-starter with built-in bypass - ABB (PSE series) - Rated input voltage 208Vac-600Vac - Rated current 25A (nom.; in-line) - Rated power 11kW (nom.; 400Vac; in-line) / 15HP (nom.; 440/480Vac; in-line) - Control voltage 24Vdc - IP00 - Surface / wall mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSE25-600-70
PSE18-600-70 Softstarter.The softstarter PSE18-600-70 has a rated maximum operational current of 18 A with an operating voltage span from 208...600 V AC. The rated control voltage is between 100...250 V AC at 50/60 Hz.
Soft-starter with built-in bypass + 3 x potentiometers - ABB (PSR series) - Rated input voltage 208Vac-600Vac - Rated current 105A (nom.; in-line) - Rated power 55kW (nom.; 400Vac; in-line) / 75HP (nom.; 440/480Vac; in-line) - IP10 - Surface / wall / DIN rail mounting - compatible with input voltages 208Vac-600Vac (220Vac / 230Vac / 240Vac / 380Vac / 400Vac / 415Vac / 440Vac / 480Vac / 500Vac / 525Vac) - item code #PSR105-600-11