Relay module, multi-channel, with 4 soldered-in miniature switching relays for DC voltage with light indicator and 1 PDT each, contact for medium to large loads, input voltage 24 V DC
2943709 CM 90-PS-230AC 24DC 2 Power Supply
Power solid-state relay, with LED and protective circuit in input and output circuits, input: TTL 5 V DC, output: short-circuit-proof, 24 V DC/max. 2 A
Input solid-state relay terminal block, input: 24 V DC, output: 3 - 48 V DC/100 mA, terminal block width: 6.2 mm
Power supply unit, primary switched-mode, input 120 V AC, output 24 V DC/5 A
Power supply unit, primary switched-mode, input 120 V AC, output 24 V DC/2.5 A
DIN rail power supply unit 24 V DC/40 A, primary switched-mode, 1-phase
Primary-switched MINI POWER power supply for DIN rail mounting, input: 1-phase, output: 5 V DC/3 A
DIN rail power supply unit 24 V DC/40 A, primary switched-mode, 3-phase
DIN rail power supply unit 24 V DC/2.5 A, primary switched-mode, 1-phase
Ex i NAMUR isolating amplifier, 2-channel. For operating proximity sensors and switches in Ex areas. The signals are transmitted via relay outputs (N/O contact) to the safe area. Line fault detection (LFD), 3-way isolation, SIL 2.
PLC-INTERFACE, consisting of DIN-rail-mountable basic terminal block in 6.2 mm with screw connection and plug-in miniature relay with 6 A power contact, 1 changeover contact, 24 V DC input voltage. Approved according to ATEX/IECEx (Zone 2) and Ex Zone Class I, Div. 2.
Universally configurable 4-way signal duplicator, with plug-in connection technology for the electrical isolation and duplication of analog signals. Configurable via DIP switch or software. Screw connection technology, standard configuration.
Hybrid motor starter for starting 3~�AC motors up to 500�V�AC and 0.6�A output current, with 24�V�DC control voltage, adjustable overload shutdown, emergency stop function to SIL�3/PL�e, and push-in connection.
Gateway for the connection of up to 32 INTERFACE system devices to a higher-level controller via EtherNet/IP. The INTERFACE system devices are connected to the Gateway via DIN rail connectors, the DIN rail connectors are provided.
Hybrid motor starter for reversing 3~�AC motors up to 500�V�AC and 2.4�A output current, with 24�V DC control voltage, adjustable overload shutdown, and screw connection.
Hybrid motor starter for starting 3~�AC motors up to 500�V AC and 2.4�A output current, with 24�V�DC control voltage, adjustable overload shutdown and emergency stop function to SIL�3/PL�e and, screw connection.
Hybrid motor starter for starting 3~�AC motors up to 500�V�AC and 2.4�A output current, with 24�V�DC control voltage, adjustable overload shutdown, and screw connection.
Safety relay for emergency stop and safety door monitoring up to SIL 3 or Cat. 4, PL e according to EN ISO 13849, single or two-channel operation, 3 enabling current paths, nominal input voltage of 24 V AC/DC, plug-in screw terminal blocks
14 mm PLC basic terminal block for high continuous currents with push-in connection, without relay or solid-state relay, for mounting on DIN rail NS 35/7,5, 1 PDT, input voltage 24 V DC
Inline, Bus coupler, EtherNet/IP, RJ45 jack, Digital inputs: 8, 24 V DC, connection method: 3-conductor, Digital outputs: 4, 24 V DC, 500 mA, connection method: 3-conductor, transmission speed in the local bus: 500 kbps / 2 Mbps, degree of protection: IP20, including Inline connectors and marking fields