Keyence

SZ-04M Keyence

Specifications

Model			SZ-04M
Type			Multi-function type
Detection capability	Minimum detectable object size		Diameter 30 mm 1.18"/40 mm 1.58", 50 mm 1.97", 70 mm 2.76", 150 mm 5.91" (depends on the setting) Reflectance 1.8% min., Speed 1.6 m/s 5.25 ft/s max.
	Detectable angle		270° (-45° to 225°)
	Response time (ON to OFF)	General scan cycle (Scan cycle A)	60 ms (2 scans) to 480 ms (16 scans)
		Specific scan cycle (Scan cycle B)	66 ms (2 scans) to 528 ms (16 scans)
	Response time (OFF to ON)	General scan cycle (Scan cycle A)	Response time of ON to OFF +125 ms
		Specific scan cycle (Scan cycle B)
	Max. protection zone	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	4.2 m 13.78' (-5° to 185°), 2.8 m 9.19' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 50 mm 1.97"	3.0 m 9.84' (-5° to 185°), 2.0 m 6.56' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 40 mm 1.58"	2.4 m 7.87' (-5° to 185°), 1.6 m 5.25' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 30 mm 1.18"	1.8 m 5.91' (-5° to 185°), 1.2 m 3.94' (-45° to -5°, 185° to 225°)
	Max. warning zone (non safety related)	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	10.0 m 32.18' (-5° to 185°), 7.0 m 22.97' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 50 mm 1.97"	7.5 m 24.61' (-5° to 185°), 5.0 m 16.4' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 40 mm 1.58"	6.0 m 19.69' (-5° to 185°), 4.0 m 13.12' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 30 mm 1.18"	4.5 m 14.76' (-5° to 185°), 3.0 m 9.84' (-45° to -5°, 185° to 225°)^*1
	Additional safety distance		100 mm 3.94"^*2
Light source	Type, wavelength		Infrared laser diode, 905 nm
	Laser class		Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10 ^*3)
OSSD output	Output		PNP or NPN (Selectable according to the connector cable) 4 outputs
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF-state voltage		Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current		Max. 1 mA^*5
	Max. capacitive load		2.2 µF (with a load resistance of 100Ω)
	Load wiring resistance		Max. 2.5Ω^*6
Input (safety-related)	Input resistance		4.4 kΩ (for Input 1, 3, 4, and 5) 2.2 kΩ (for Input 2 and 6)
Non safety-related output (AUX output)	Output		PNP/NPN totem pole output 6 outputs
	Max. load current		50 mA
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
Muting lamp output	(AUX6 output can be assigned for the muting lamp output)		Can be connected to the incandescent lamp (24 V DC, 1 to 5.5 W) and LED lamp (load current 10 to 230 mA)
Cable length			30 m 98.43' or less ^*7
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL 61496-1
		EMI	EN55011 Class A, FCC Part15B Class A
	Safety		IEC61496-1, EN61496-1, UL 61496-1 (Type 3 ESPE), IEC61496-3, EN61496-3 (Type 3 AOPDDR) IEC61508, EN61508, IEC62061, EN62061 (SIL2), EN ISO13849-1:2015 (PL d, Category 3) UL508, UL1998
Rating	Power voltage		When using a converter power supply: 24 VDC ±10 %, Ripple (P-P) 10 % or less When using a battery: 24 VDC +20 %/-30 %
	Power consumption		Max. 9.5 W (without load) Max. 50 W (with load)
Environmental resistance	Enclosure rating		IP65 (IEC60529)^*8
	Ambient light		Incandescent lamp: 1,500 lux or less^*9
	Operating ambient temperature		-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity		35 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		35 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum die casting, SPHC (Bottom)
	Window		Polycarbonate
Weight			Approx. 1.6 kg
^1 20% or more reflectance is necessary for the minimum detectable object in the warning zone. ^2 If there is a high reflective background within 1.5 m 4.921' from the boundary of the protection zone, 200 mm 7.87" must be added as supplementary necessary distance to the protection zone in case of calculation of the minimum safety distance. ^3 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^4 For the load current calculation of the OSSD output and the AUX output, make sure it is 1.5 A or less when using converter power supply (or 1.0 A or less when the cable length is 25 m 82.02' or more), and 1.0 A or less when using a battery (or 0.5 A or less when the cable length is 5 m 16.40' or more) ^5 This also takes into account the situations when power is either off or disconnected. ^6 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operation. However, it must be 1.0 Ω or less if the load current is 300 mA or more. ^7 It must be 10 m 32.81' or less if the power is supplied by battery. ^8 When the setting cover is open, or the connector cable is not connected, the IP65 certification cannot be met. In addition, the SZ-16D doesn't fulfill the requirements of IP65 degree of protection with the connector cable for the RS-422A communication unattached.. ^*9 The SZ should not be installed so as to have light interference within ±5° to the detection plane.

24,925.00 kr

1-year warranty

FREE WORDWIDE SHIPPING

Est. delivery between and

Condition:

Sealed Surplus

SKU: SZ-04M-Sealed

Sold out

0.00 kr

Never Used Surplus

SKU: SZ-04M

5 verified stock

24,925.00 kr

Used

SKU: SZ-04M-Used

Sold out

0.00 kr

Variant

Quantity:

Need More?

Specifications

Model			SZ-04M
Type			Multi-function type
Detection capability	Minimum detectable object size		Diameter 30 mm 1.18"/40 mm 1.58", 50 mm 1.97", 70 mm 2.76", 150 mm 5.91" (depends on the setting) Reflectance 1.8% min., Speed 1.6 m/s 5.25 ft/s max.
	Detectable angle		270° (-45° to 225°)
	Response time (ON to OFF)	General scan cycle (Scan cycle A)	60 ms (2 scans) to 480 ms (16 scans)
		Specific scan cycle (Scan cycle B)	66 ms (2 scans) to 528 ms (16 scans)
	Response time (OFF to ON)	General scan cycle (Scan cycle A)	Response time of ON to OFF +125 ms
		Specific scan cycle (Scan cycle B)
	Max. protection zone	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	4.2 m 13.78' (-5° to 185°), 2.8 m 9.19' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 50 mm 1.97"	3.0 m 9.84' (-5° to 185°), 2.0 m 6.56' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 40 mm 1.58"	2.4 m 7.87' (-5° to 185°), 1.6 m 5.25' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 30 mm 1.18"	1.8 m 5.91' (-5° to 185°), 1.2 m 3.94' (-45° to -5°, 185° to 225°)
	Max. warning zone (non safety related)	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	10.0 m 32.18' (-5° to 185°), 7.0 m 22.97' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 50 mm 1.97"	7.5 m 24.61' (-5° to 185°), 5.0 m 16.4' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 40 mm 1.58"	6.0 m 19.69' (-5° to 185°), 4.0 m 13.12' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 30 mm 1.18"	4.5 m 14.76' (-5° to 185°), 3.0 m 9.84' (-45° to -5°, 185° to 225°)^*1
	Additional safety distance		100 mm 3.94"^*2
Light source	Type, wavelength		Infrared laser diode, 905 nm
	Laser class		Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10 ^*3)
OSSD output	Output		PNP or NPN (Selectable according to the connector cable) 4 outputs
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF-state voltage		Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current		Max. 1 mA^*5
	Max. capacitive load		2.2 µF (with a load resistance of 100Ω)
	Load wiring resistance		Max. 2.5Ω^*6
Input (safety-related)	Input resistance		4.4 kΩ (for Input 1, 3, 4, and 5) 2.2 kΩ (for Input 2 and 6)
Non safety-related output (AUX output)	Output		PNP/NPN totem pole output 6 outputs
	Max. load current		50 mA
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
Muting lamp output	(AUX6 output can be assigned for the muting lamp output)		Can be connected to the incandescent lamp (24 V DC, 1 to 5.5 W) and LED lamp (load current 10 to 230 mA)
Cable length			30 m 98.43' or less ^*7
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL 61496-1
		EMI	EN55011 Class A, FCC Part15B Class A
	Safety		IEC61496-1, EN61496-1, UL 61496-1 (Type 3 ESPE), IEC61496-3, EN61496-3 (Type 3 AOPDDR) IEC61508, EN61508, IEC62061, EN62061 (SIL2), EN ISO13849-1:2015 (PL d, Category 3) UL508, UL1998
Rating	Power voltage		When using a converter power supply: 24 VDC ±10 %, Ripple (P-P) 10 % or less When using a battery: 24 VDC +20 %/-30 %
	Power consumption		Max. 9.5 W (without load) Max. 50 W (with load)
Environmental resistance	Enclosure rating		IP65 (IEC60529)^*8
	Ambient light		Incandescent lamp: 1,500 lux or less^*9
	Operating ambient temperature		-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity		35 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		35 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum die casting, SPHC (Bottom)
	Window		Polycarbonate
Weight			Approx. 1.6 kg
^1 20% or more reflectance is necessary for the minimum detectable object in the warning zone. ^2 If there is a high reflective background within 1.5 m 4.921' from the boundary of the protection zone, 200 mm 7.87" must be added as supplementary necessary distance to the protection zone in case of calculation of the minimum safety distance. ^3 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^4 For the load current calculation of the OSSD output and the AUX output, make sure it is 1.5 A or less when using converter power supply (or 1.0 A or less when the cable length is 25 m 82.02' or more), and 1.0 A or less when using a battery (or 0.5 A or less when the cable length is 5 m 16.40' or more) ^5 This also takes into account the situations when power is either off or disconnected. ^6 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operation. However, it must be 1.0 Ω or less if the load current is 300 mA or more. ^7 It must be 10 m 32.81' or less if the power is supplied by battery. ^8 When the setting cover is open, or the connector cable is not connected, the IP65 certification cannot be met. In addition, the SZ-16D doesn't fulfill the requirements of IP65 degree of protection with the connector cable for the RS-422A communication unattached.. ^*9 The SZ should not be installed so as to have light interference within ±5° to the detection plane.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Specifications

Model			SZ-04M
Type			Multi-function type
Detection capability	Minimum detectable object size		Diameter 30 mm 1.18"/40 mm 1.58", 50 mm 1.97", 70 mm 2.76", 150 mm 5.91" (depends on the setting) Reflectance 1.8% min., Speed 1.6 m/s 5.25 ft/s max.
	Detectable angle		270° (-45° to 225°)
	Response time (ON to OFF)	General scan cycle (Scan cycle A)	60 ms (2 scans) to 480 ms (16 scans)
		Specific scan cycle (Scan cycle B)	66 ms (2 scans) to 528 ms (16 scans)
	Response time (OFF to ON)	General scan cycle (Scan cycle A)	Response time of ON to OFF +125 ms
		Specific scan cycle (Scan cycle B)
	Max. protection zone	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	4.2 m 13.78' (-5° to 185°), 2.8 m 9.19' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 50 mm 1.97"	3.0 m 9.84' (-5° to 185°), 2.0 m 6.56' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 40 mm 1.58"	2.4 m 7.87' (-5° to 185°), 1.6 m 5.25' (-45° to -5°, 185° to 225°)
		Minimum detectable object size: 30 mm 1.18"	1.8 m 5.91' (-5° to 185°), 1.2 m 3.94' (-45° to -5°, 185° to 225°)
	Max. warning zone (non safety related)	Minimum detectable object size: 70 mm 2.76"/150 mm 5.91"	10.0 m 32.18' (-5° to 185°), 7.0 m 22.97' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 50 mm 1.97"	7.5 m 24.61' (-5° to 185°), 5.0 m 16.4' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 40 mm 1.58"	6.0 m 19.69' (-5° to 185°), 4.0 m 13.12' (-45° to -5°, 185° to 225°)^*1
		Minimum detectable object size: 30 mm 1.18"	4.5 m 14.76' (-5° to 185°), 3.0 m 9.84' (-45° to -5°, 185° to 225°)^*1
	Additional safety distance		100 mm 3.94"^*2
Light source	Type, wavelength		Infrared laser diode, 905 nm
	Laser class		Class 1 Laser Product (IEC 60825-1, FDA (CDRH) Part 1040.10 ^*3)
OSSD output	Output		PNP or NPN (Selectable according to the connector cable) 4 outputs
	Max. load current		500 mA^*4
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
	OFF-state voltage		Max. 2.0 V (with a cable length of 5 m 16.4')
	Leakage current		Max. 1 mA^*5
	Max. capacitive load		2.2 µF (with a load resistance of 100Ω)
	Load wiring resistance		Max. 2.5Ω^*6
Input (safety-related)	Input resistance		4.4 kΩ (for Input 1, 3, 4, and 5) 2.2 kΩ (for Input 2 and 6)
Non safety-related output (AUX output)	Output		PNP/NPN totem pole output 6 outputs
	Max. load current		50 mA
	Residual voltage (during ON)		Max. 2.5 V (with a cable length of 5 m 16.4')
Muting lamp output	(AUX6 output can be assigned for the muting lamp output)		Can be connected to the incandescent lamp (24 V DC, 1 to 5.5 W) and LED lamp (load current 10 to 230 mA)
Cable length			30 m 98.43' or less ^*7
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL 61496-1
		EMI	EN55011 Class A, FCC Part15B Class A
	Safety		IEC61496-1, EN61496-1, UL 61496-1 (Type 3 ESPE), IEC61496-3, EN61496-3 (Type 3 AOPDDR) IEC61508, EN61508, IEC62061, EN62061 (SIL2), EN ISO13849-1:2015 (PL d, Category 3) UL508, UL1998
Rating	Power voltage		When using a converter power supply: 24 VDC ±10 %, Ripple (P-P) 10 % or less When using a battery: 24 VDC +20 %/-30 %
	Power consumption		Max. 9.5 W (without load) Max. 50 W (with load)
Environmental resistance	Enclosure rating		IP65 (IEC60529)^*8
	Ambient light		Incandescent lamp: 1,500 lux or less^*9
	Operating ambient temperature		-10 to +50 °C 14 to 122 °F (No freezing)
	Operating relative humidity		35 to 85 % RH (No condensation)
	Storage temperature		-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity		35 to 95 % RH
	Vibration resistance		10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case		Aluminum die casting, SPHC (Bottom)
	Window		Polycarbonate
Weight			Approx. 1.6 kg
^1 20% or more reflectance is necessary for the minimum detectable object in the warning zone. ^2 If there is a high reflective background within 1.5 m 4.921' from the boundary of the protection zone, 200 mm 7.87" must be added as supplementary necessary distance to the protection zone in case of calculation of the minimum safety distance. ^3 The laser classification for FDA (CDRH) is implemented based on IEC60825-1 in accordance with the requirements of Laser Notice. ^4 For the load current calculation of the OSSD output and the AUX output, make sure it is 1.5 A or less when using converter power supply (or 1.0 A or less when the cable length is 25 m 82.02' or more), and 1.0 A or less when using a battery (or 0.5 A or less when the cable length is 5 m 16.40' or more) ^5 This also takes into account the situations when power is either off or disconnected. ^6 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operation. However, it must be 1.0 Ω or less if the load current is 300 mA or more. ^7 It must be 10 m 32.81' or less if the power is supplied by battery. ^8 When the setting cover is open, or the connector cable is not connected, the IP65 certification cannot be met. In addition, the SZ-16D doesn't fulfill the requirements of IP65 degree of protection with the connector cable for the RS-422A communication unattached.. ^*9 The SZ should not be installed so as to have light interference within ±5° to the detection plane.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

SZ-04M Keyence

Specifications

Specifications

Specifications

SZ-04M Keyence

Specifications

Specifications

Trusted By

You may also like

Recently viewed