LK-G5001V Keyence

Specifications

Model		LK-G5001V^1^2
Separate type		LK-G5001/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx. 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Non-voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Non-voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	NPN open-collector output
	General comparator output
Expansion connector	TIMING input	Non-voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Est. delivery between and

21,650.00 kr

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: LK-G5001V-Sealed

3 verified stock

21,650.00 kr

Never Used Surplus

SKU: LK-G5001V

2 verified stock

19,810.00 kr

Used

SKU: LK-G5001V-Used

Sold out

0.00 kr

Variant

Quantity:

Need More?

Specifications

Model		LK-G5001V^1^2
Separate type		LK-G5001/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx. 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Non-voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Non-voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	NPN open-collector output
	General comparator output
Expansion connector	TIMING input	Non-voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

Model		LK-G5001V^1^2
Separate type		LK-G5001/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx. 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Non-voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Non-voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	NPN open-collector output
	General comparator output
Expansion connector	TIMING input	Non-voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	NPN open-collector output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP™interface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP™, CC-Link, and DeviceNet® cannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet® unit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	When one or less head expansion unit is connected: 0 to +50 °C 32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C 32 to 104 °F.
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1 NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. ^2 Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3 This input is applied to all of the synchronized OUT. ^4 When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5 When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6 Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7 The EtherNet/IP™ interface cannot be used when a CC-Link unit or a DeviceNet® unit is installed. EtherNet/IP™ is supported by the latest controllers. For details on which controllers support EtherNet/IP™ , contact your nearest KEYENCE office.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator