KV-NC32T Keyence

Specifications

Model				KV-NC32T
General specifications	Power voltage			24 VDC (+10%/-15%)
	Operating ambient temperature			0 to 55°C 32 to 131°F (no freezing)^*1
	Operating ambient humidity			5 to 95% RH (no condensation)
	Operating environment			As little dust and corrosive gas as possible
	Noise immunity			1500 V peak-to-peak or more, pulse duration 1 μs, 50 ns (based on noise simulator) Conforms to IEC standards (IEC61000-4-2/3/4/6)
	Withstand voltage			1500 VAC for 1 minute, between power supply terminal and I/O terminals and between all external terminals and case (1000 VAC for 1 minute, between power supply terminal and output terminals for the transistor output type expansion I/O unit)
	Insulation resistance			50 MΩ or more (500 VDC megger used to perform measurements between power supply terminal and input terminals, and between all external terminals and case)
	Storage temperature			−25 to +75°C −13 to +167°F
	Vibration resistance	Intermittent vibration	Frequency: 5 to 9 Hz	Amplitude: 3.5 mm 0.14"^*2
			Frequency: 9 to 150 Hz	Acceleration: 9.8 m/s² 32.2'/s²^*2
		Continuous vibration	Frequency: 5 to 9 Hz	Amplitude: 1.75 mm 0.07"^*2
			Frequency: 9 to 150 Hz	Acceleration: 4.9 m/s² 16.1'/s²^*2
	Shock resistance			Acceleration: 150 m/s² 492.1'/s², application time: 11 ms, three times in each of the X, Y, and Z directions
	Operating altitude			2000 m 6561.7' or less
	Overvoltage category			I
	Pollution degree			2
Performance specifications	Calculation control method			Program storage method
	I/O control method			Refresh method
	Program language			Expanded ladder, KV Script, mnemonic
	Number of instructions			Basic instruction: 81 types and 182 instructions, Application instruction: 39 types and 56 instructions Calculation instruction: 123 types and 311 instructions, Expansion instruction: 92 types and 141 instructions Total: 335 types and 690 instructions
	Instruction execution speed			Basic instruction: 50 ns minimum, Application instruction: 170 ns minimum
	Program capacity			32k steps
	Maximum number of attachable I/O units			8
	Maximum number of I/O points			256
	Input relay/Output relay/Internal auxiliary relay	R		Total of 9600 points 1 bit (R000 to R59915)
	Link relay	B		8192 points 1 bit (B0 to B1FFF)
	Internal auxiliary relay	MR		9600 points 1 bit (MR000 to MR59915)
	Latch relay	LR		3200 points 1 bit (LR000 to LR19915)
	Control relay	CR		1440 points 1 bit (CR000 to CR8915)
	Timer	T		512 points 32 bits (T0 to T511)
	Counter	C		256 points 32 bits (C0 to C255)
	Data memory	DM		32768 points 16 bit (DM0 to DM32767)
	Link register	W		16384 points 16 bit (W0 to W3FFF)
	Temporary memory	TM		512 points 16 bit (TM0 to TM511)
	High-speed counter	CTH		3 points (CTH0 to CTH2) 32-bit automatic reset counter^3 (Input response: 100 kHz per single phase, 50 kHz per phase difference)^4
	High-speed counter comparator	CTC		6 points (CTC0 to CTC5) 32 bits, two points per high-speed counter
	Index register	Z		12 points 32 bit (Z01 to Z12)
	Control memory	CM		9000 points 16 bit (CM0 to CM8999)
	Positioning pulse output			3 axes Maximum output frequency: 100 kHz
	Base unit I/O			Input: 16 points output: 16 points Input common: 1 point Output common: 1 point
	Number of comments and labels that can be stored in the main unit	Device comment		20000 When a maximum-length ladder program is written with no labels.
		Label		28000 When a maximum-length ladder program is written with no device comments.
	Power off hold function	Program memory		Flash ROM can be rewritten 10000 times
		Device		Nonvolatile RAM^*5
	Clock function			±60 seconds/month (at 25°C 77°F)
	Self-diagnosis function			CPU error, RAM error, and other problems
Input specifications	Relay number			General input: R000 to R009 (10 points), High-speed A-phase and B-phase input: R010 to R015 (6 points)
	Input mode			24 VDC input (open collector)
	Maximum input voltage			26.4 VDC
	Rated input voltage			24 VDC (General input: 5.3 mA, High-speed A-phase and B-phase input: 6.5 mA^*6)
	Minimum ON voltage			19 VDC
	Maximum OFF current			1.5 mA
	Common method			All points/1 common (1 terminal)
	Circuit delay time			General input: OFF to ON: Max. 30 μs (Typ. 3.5 μs), ON to OFF: Max. 50 μs (Typ. 15 μs) High-speed A-phase and B-phase input: OFF to ON: Max. 2 μs (Typ. 1.1 μs), ON to OFF: Max. 2 μs (Typ. 0.3 μs) ^*7
	Input time constant			Normal: 10 ms, When the HSP instruction is used: 10 μs When CR2305 is turned ON: 10 μs to 10 ms, eight-level switching is possible (set with CM1620). Can also be set from the Unit Editor.^*7
				Delay by input time constant Input time constant setting 10 μs: Digital filter 1.6 to 2 μs Input time constant setting 20 μs: Digital filter 9 to 12 μs Input time constant setting 110 μs: Digital filter 90 to 93 μs Input time constant setting 500 μs: Digital filter 300 to 400 μs Input time constant setting 1 ms: Digital filter 800 to 900 μs Input time constant setting 2.5 ms: Digital filter 2.3 to 2.4 ms Input time constant setting 5 ms: Digital filter 4.0 to 4.5 ms Input time constant setting 10 ms: Digital filter 9 to 9.5 ms
	Response frequency			(High-speed A-phase and B-phase input) Single phase: 100 kHz, phase difference: 50 kHz, 24 V ±10%, Duty 50%
Output specifications	Relay number			General output: R506 to R515 (10 points), High-speed output: R500 to R505 (6 points)
	Output mode			MOSFET (N-ch) output
	Rated load			30 VDC General output: 0.2 A (1.6 A/common), High-speed output: 0.3 A (1.6 A/common)
	Maximum OFF voltage			30 VDC
	Leakage current at OFF			100 μA or less
	Residual voltage at ON			0.6 VDC or less
	Common method			16 points/1 common
	ON/OFF response time			General output: OFF to ON: 100 μs (load of 1 mA or more), ON to OFF: 200 μs (load of 1 mA or more) High-speed output: OFF to ON: 2 μs (load of 7 mA or more), ON to OFF: 5 μs (load of 7 mA or more)
	Overcurrent protection			Protection provided for each common^*8
	Output frequency			High-speed output: 100 kHz (7 to 100 mA load)
Built-in serial port	Interface	Communication standard		RS-232C
		Connection		Modular connector
	Transmission specifications RS-232C	Baud rate		1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
		Transmission method		Full duplex
		Data format	Start bit	1 bit
			Data bits	7 bits, 8 bits
			Stop bits	1 bit, 2 bits
		Error detection	Parity	Even, odd, none
		Transmission distance		15 m 49.2'
		Number of transmission units		1
	Indication			Common between SD/RD SD: (green) RD: (red) The color may appear as orange during transmission.
Internal current consumption				260 mA
Weight				Approx. 220 g
^1 The temperature below the unit center (30 mm 1.18") inside a control panel. ^2 Conforms to JIS B 3502 and IEC61131-2. Scan times: 10 times (100 minutes) in each of the X, Y, and Z directions ^3 You can also configure the settings so that automatic reset is not used. ^4 Only open collectors are supported. Line drivers are not supported. ^5 You can set the target device by clicking “CPU system setting” and then “Power off holding” in KV STUDIO. ^6 Reference value of input current. ^7 The input response time corresponding to the input time constant can be calculated as shown below. (Response time) = (Circuit delay of the input circuit) + (Delay by the digital filter) Example: Maximum response time when the input time constant is set to 10 μs OFF to ON: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs ON to OFF: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs Example: Maximum response time when the input time constant is set to 500 μs OFF to ON: 30 μs (circuit delay) + 400 μs (digital filter) = 430 μs ON to OFF: 50 μs (circuit delay) + 400 μs (digital filter) = 450 μs ^8 If an overcurrent occurs, protection operation (output turned OFF) and automatic recovery are repeated for all outputs within the shared common until the cause of the problem is removed.

Est. delivery between and

3,324.00 kr

1-year warranty

FREE WORDWIDE SHIPPING

Condition:

Sealed Surplus

SKU: KV-NC32T-Sealed

9 verified stock

3,324.00 kr

Never Used Surplus

SKU: KV-NC32T

Sold out

0.00 kr

Used

SKU: KV-NC32T-Used

Sold out

0.00 kr

Variant

Quantity:

Need More?

Specifications

Model				KV-NC32T
General specifications	Power voltage			24 VDC (+10%/-15%)
	Operating ambient temperature			0 to 55°C 32 to 131°F (no freezing)^*1
	Operating ambient humidity			5 to 95% RH (no condensation)
	Operating environment			As little dust and corrosive gas as possible
	Noise immunity			1500 V peak-to-peak or more, pulse duration 1 μs, 50 ns (based on noise simulator) Conforms to IEC standards (IEC61000-4-2/3/4/6)
	Withstand voltage			1500 VAC for 1 minute, between power supply terminal and I/O terminals and between all external terminals and case (1000 VAC for 1 minute, between power supply terminal and output terminals for the transistor output type expansion I/O unit)
	Insulation resistance			50 MΩ or more (500 VDC megger used to perform measurements between power supply terminal and input terminals, and between all external terminals and case)
	Storage temperature			−25 to +75°C −13 to +167°F
	Vibration resistance	Intermittent vibration	Frequency: 5 to 9 Hz	Amplitude: 3.5 mm 0.14"^*2
			Frequency: 9 to 150 Hz	Acceleration: 9.8 m/s² 32.2'/s²^*2
		Continuous vibration	Frequency: 5 to 9 Hz	Amplitude: 1.75 mm 0.07"^*2
			Frequency: 9 to 150 Hz	Acceleration: 4.9 m/s² 16.1'/s²^*2
	Shock resistance			Acceleration: 150 m/s² 492.1'/s², application time: 11 ms, three times in each of the X, Y, and Z directions
	Operating altitude			2000 m 6561.7' or less
	Overvoltage category			I
	Pollution degree			2
Performance specifications	Calculation control method			Program storage method
	I/O control method			Refresh method
	Program language			Expanded ladder, KV Script, mnemonic
	Number of instructions			Basic instruction: 81 types and 182 instructions, Application instruction: 39 types and 56 instructions Calculation instruction: 123 types and 311 instructions, Expansion instruction: 92 types and 141 instructions Total: 335 types and 690 instructions
	Instruction execution speed			Basic instruction: 50 ns minimum, Application instruction: 170 ns minimum
	Program capacity			32k steps
	Maximum number of attachable I/O units			8
	Maximum number of I/O points			256
	Input relay/Output relay/Internal auxiliary relay	R		Total of 9600 points 1 bit (R000 to R59915)
	Link relay	B		8192 points 1 bit (B0 to B1FFF)
	Internal auxiliary relay	MR		9600 points 1 bit (MR000 to MR59915)
	Latch relay	LR		3200 points 1 bit (LR000 to LR19915)
	Control relay	CR		1440 points 1 bit (CR000 to CR8915)
	Timer	T		512 points 32 bits (T0 to T511)
	Counter	C		256 points 32 bits (C0 to C255)
	Data memory	DM		32768 points 16 bit (DM0 to DM32767)
	Link register	W		16384 points 16 bit (W0 to W3FFF)
	Temporary memory	TM		512 points 16 bit (TM0 to TM511)
	High-speed counter	CTH		3 points (CTH0 to CTH2) 32-bit automatic reset counter^3 (Input response: 100 kHz per single phase, 50 kHz per phase difference)^4
	High-speed counter comparator	CTC		6 points (CTC0 to CTC5) 32 bits, two points per high-speed counter
	Index register	Z		12 points 32 bit (Z01 to Z12)
	Control memory	CM		9000 points 16 bit (CM0 to CM8999)
	Positioning pulse output			3 axes Maximum output frequency: 100 kHz
	Base unit I/O			Input: 16 points output: 16 points Input common: 1 point Output common: 1 point
	Number of comments and labels that can be stored in the main unit	Device comment		20000 When a maximum-length ladder program is written with no labels.
		Label		28000 When a maximum-length ladder program is written with no device comments.
	Power off hold function	Program memory		Flash ROM can be rewritten 10000 times
		Device		Nonvolatile RAM^*5
	Clock function			±60 seconds/month (at 25°C 77°F)
	Self-diagnosis function			CPU error, RAM error, and other problems
Input specifications	Relay number			General input: R000 to R009 (10 points), High-speed A-phase and B-phase input: R010 to R015 (6 points)
	Input mode			24 VDC input (open collector)
	Maximum input voltage			26.4 VDC
	Rated input voltage			24 VDC (General input: 5.3 mA, High-speed A-phase and B-phase input: 6.5 mA^*6)
	Minimum ON voltage			19 VDC
	Maximum OFF current			1.5 mA
	Common method			All points/1 common (1 terminal)
	Circuit delay time			General input: OFF to ON: Max. 30 μs (Typ. 3.5 μs), ON to OFF: Max. 50 μs (Typ. 15 μs) High-speed A-phase and B-phase input: OFF to ON: Max. 2 μs (Typ. 1.1 μs), ON to OFF: Max. 2 μs (Typ. 0.3 μs) ^*7
	Input time constant			Normal: 10 ms, When the HSP instruction is used: 10 μs When CR2305 is turned ON: 10 μs to 10 ms, eight-level switching is possible (set with CM1620). Can also be set from the Unit Editor.^*7
				Delay by input time constant Input time constant setting 10 μs: Digital filter 1.6 to 2 μs Input time constant setting 20 μs: Digital filter 9 to 12 μs Input time constant setting 110 μs: Digital filter 90 to 93 μs Input time constant setting 500 μs: Digital filter 300 to 400 μs Input time constant setting 1 ms: Digital filter 800 to 900 μs Input time constant setting 2.5 ms: Digital filter 2.3 to 2.4 ms Input time constant setting 5 ms: Digital filter 4.0 to 4.5 ms Input time constant setting 10 ms: Digital filter 9 to 9.5 ms
	Response frequency			(High-speed A-phase and B-phase input) Single phase: 100 kHz, phase difference: 50 kHz, 24 V ±10%, Duty 50%
Output specifications	Relay number			General output: R506 to R515 (10 points), High-speed output: R500 to R505 (6 points)
	Output mode			MOSFET (N-ch) output
	Rated load			30 VDC General output: 0.2 A (1.6 A/common), High-speed output: 0.3 A (1.6 A/common)
	Maximum OFF voltage			30 VDC
	Leakage current at OFF			100 μA or less
	Residual voltage at ON			0.6 VDC or less
	Common method			16 points/1 common
	ON/OFF response time			General output: OFF to ON: 100 μs (load of 1 mA or more), ON to OFF: 200 μs (load of 1 mA or more) High-speed output: OFF to ON: 2 μs (load of 7 mA or more), ON to OFF: 5 μs (load of 7 mA or more)
	Overcurrent protection			Protection provided for each common^*8
	Output frequency			High-speed output: 100 kHz (7 to 100 mA load)
Built-in serial port	Interface	Communication standard		RS-232C
		Connection		Modular connector
	Transmission specifications RS-232C	Baud rate		1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
		Transmission method		Full duplex
		Data format	Start bit	1 bit
			Data bits	7 bits, 8 bits
			Stop bits	1 bit, 2 bits
		Error detection	Parity	Even, odd, none
		Transmission distance		15 m 49.2'
		Number of transmission units		1
	Indication			Common between SD/RD SD: (green) RD: (red) The color may appear as orange during transmission.
Internal current consumption				260 mA
Weight				Approx. 220 g
^1 The temperature below the unit center (30 mm 1.18") inside a control panel. ^2 Conforms to JIS B 3502 and IEC61131-2. Scan times: 10 times (100 minutes) in each of the X, Y, and Z directions ^3 You can also configure the settings so that automatic reset is not used. ^4 Only open collectors are supported. Line drivers are not supported. ^5 You can set the target device by clicking “CPU system setting” and then “Power off holding” in KV STUDIO. ^6 Reference value of input current. ^7 The input response time corresponding to the input time constant can be calculated as shown below. (Response time) = (Circuit delay of the input circuit) + (Delay by the digital filter) Example: Maximum response time when the input time constant is set to 10 μs OFF to ON: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs ON to OFF: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs Example: Maximum response time when the input time constant is set to 500 μs OFF to ON: 30 μs (circuit delay) + 400 μs (digital filter) = 430 μs ON to OFF: 50 μs (circuit delay) + 400 μs (digital filter) = 450 μs ^8 If an overcurrent occurs, protection operation (output turned OFF) and automatic recovery are repeated for all outputs within the shared common until the cause of the problem is removed.

Model				KV-NC32T
General specifications	Power voltage			24 VDC (+10%/-15%)
	Operating ambient temperature			0 to 55°C 32 to 131°F (no freezing)^*1
	Operating ambient humidity			5 to 95% RH (no condensation)
	Operating environment			As little dust and corrosive gas as possible
	Noise immunity			1500 V peak-to-peak or more, pulse duration 1 μs, 50 ns (based on noise simulator) Conforms to IEC standards (IEC61000-4-2/3/4/6)
	Withstand voltage			1500 VAC for 1 minute, between power supply terminal and I/O terminals and between all external terminals and case (1000 VAC for 1 minute, between power supply terminal and output terminals for the transistor output type expansion I/O unit)
	Insulation resistance			50 MΩ or more (500 VDC megger used to perform measurements between power supply terminal and input terminals, and between all external terminals and case)
	Storage temperature			−25 to +75°C −13 to +167°F
	Vibration resistance	Intermittent vibration	Frequency: 5 to 9 Hz	Amplitude: 3.5 mm 0.14"^*2
			Frequency: 9 to 150 Hz	Acceleration: 9.8 m/s² 32.2'/s²^*2
		Continuous vibration	Frequency: 5 to 9 Hz	Amplitude: 1.75 mm 0.07"^*2
			Frequency: 9 to 150 Hz	Acceleration: 4.9 m/s² 16.1'/s²^*2
	Shock resistance			Acceleration: 150 m/s² 492.1'/s², application time: 11 ms, three times in each of the X, Y, and Z directions
	Operating altitude			2000 m 6561.7' or less
	Overvoltage category			I
	Pollution degree			2
Performance specifications	Calculation control method			Program storage method
	I/O control method			Refresh method
	Program language			Expanded ladder, KV Script, mnemonic
	Number of instructions			Basic instruction: 81 types and 182 instructions, Application instruction: 39 types and 56 instructions Calculation instruction: 123 types and 311 instructions, Expansion instruction: 92 types and 141 instructions Total: 335 types and 690 instructions
	Instruction execution speed			Basic instruction: 50 ns minimum, Application instruction: 170 ns minimum
	Program capacity			32k steps
	Maximum number of attachable I/O units			8
	Maximum number of I/O points			256
	Input relay/Output relay/Internal auxiliary relay	R		Total of 9600 points 1 bit (R000 to R59915)
	Link relay	B		8192 points 1 bit (B0 to B1FFF)
	Internal auxiliary relay	MR		9600 points 1 bit (MR000 to MR59915)
	Latch relay	LR		3200 points 1 bit (LR000 to LR19915)
	Control relay	CR		1440 points 1 bit (CR000 to CR8915)
	Timer	T		512 points 32 bits (T0 to T511)
	Counter	C		256 points 32 bits (C0 to C255)
	Data memory	DM		32768 points 16 bit (DM0 to DM32767)
	Link register	W		16384 points 16 bit (W0 to W3FFF)
	Temporary memory	TM		512 points 16 bit (TM0 to TM511)
	High-speed counter	CTH		3 points (CTH0 to CTH2) 32-bit automatic reset counter^3 (Input response: 100 kHz per single phase, 50 kHz per phase difference)^4
	High-speed counter comparator	CTC		6 points (CTC0 to CTC5) 32 bits, two points per high-speed counter
	Index register	Z		12 points 32 bit (Z01 to Z12)
	Control memory	CM		9000 points 16 bit (CM0 to CM8999)
	Positioning pulse output			3 axes Maximum output frequency: 100 kHz
	Base unit I/O			Input: 16 points output: 16 points Input common: 1 point Output common: 1 point
	Number of comments and labels that can be stored in the main unit	Device comment		20000 When a maximum-length ladder program is written with no labels.
		Label		28000 When a maximum-length ladder program is written with no device comments.
	Power off hold function	Program memory		Flash ROM can be rewritten 10000 times
		Device		Nonvolatile RAM^*5
	Clock function			±60 seconds/month (at 25°C 77°F)
	Self-diagnosis function			CPU error, RAM error, and other problems
Input specifications	Relay number			General input: R000 to R009 (10 points), High-speed A-phase and B-phase input: R010 to R015 (6 points)
	Input mode			24 VDC input (open collector)
	Maximum input voltage			26.4 VDC
	Rated input voltage			24 VDC (General input: 5.3 mA, High-speed A-phase and B-phase input: 6.5 mA^*6)
	Minimum ON voltage			19 VDC
	Maximum OFF current			1.5 mA
	Common method			All points/1 common (1 terminal)
	Circuit delay time			General input: OFF to ON: Max. 30 μs (Typ. 3.5 μs), ON to OFF: Max. 50 μs (Typ. 15 μs) High-speed A-phase and B-phase input: OFF to ON: Max. 2 μs (Typ. 1.1 μs), ON to OFF: Max. 2 μs (Typ. 0.3 μs) ^*7
	Input time constant			Normal: 10 ms, When the HSP instruction is used: 10 μs When CR2305 is turned ON: 10 μs to 10 ms, eight-level switching is possible (set with CM1620). Can also be set from the Unit Editor.^*7
				Delay by input time constant Input time constant setting 10 μs: Digital filter 1.6 to 2 μs Input time constant setting 20 μs: Digital filter 9 to 12 μs Input time constant setting 110 μs: Digital filter 90 to 93 μs Input time constant setting 500 μs: Digital filter 300 to 400 μs Input time constant setting 1 ms: Digital filter 800 to 900 μs Input time constant setting 2.5 ms: Digital filter 2.3 to 2.4 ms Input time constant setting 5 ms: Digital filter 4.0 to 4.5 ms Input time constant setting 10 ms: Digital filter 9 to 9.5 ms
	Response frequency			(High-speed A-phase and B-phase input) Single phase: 100 kHz, phase difference: 50 kHz, 24 V ±10%, Duty 50%
Output specifications	Relay number			General output: R506 to R515 (10 points), High-speed output: R500 to R505 (6 points)
	Output mode			MOSFET (N-ch) output
	Rated load			30 VDC General output: 0.2 A (1.6 A/common), High-speed output: 0.3 A (1.6 A/common)
	Maximum OFF voltage			30 VDC
	Leakage current at OFF			100 μA or less
	Residual voltage at ON			0.6 VDC or less
	Common method			16 points/1 common
	ON/OFF response time			General output: OFF to ON: 100 μs (load of 1 mA or more), ON to OFF: 200 μs (load of 1 mA or more) High-speed output: OFF to ON: 2 μs (load of 7 mA or more), ON to OFF: 5 μs (load of 7 mA or more)
	Overcurrent protection			Protection provided for each common^*8
	Output frequency			High-speed output: 100 kHz (7 to 100 mA load)
Built-in serial port	Interface	Communication standard		RS-232C
		Connection		Modular connector
	Transmission specifications RS-232C	Baud rate		1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps
		Transmission method		Full duplex
		Data format	Start bit	1 bit
			Data bits	7 bits, 8 bits
			Stop bits	1 bit, 2 bits
		Error detection	Parity	Even, odd, none
		Transmission distance		15 m 49.2'
		Number of transmission units		1
	Indication			Common between SD/RD SD: (green) RD: (red) The color may appear as orange during transmission.
Internal current consumption				260 mA
Weight				Approx. 220 g
^1 The temperature below the unit center (30 mm 1.18") inside a control panel. ^2 Conforms to JIS B 3502 and IEC61131-2. Scan times: 10 times (100 minutes) in each of the X, Y, and Z directions ^3 You can also configure the settings so that automatic reset is not used. ^4 Only open collectors are supported. Line drivers are not supported. ^5 You can set the target device by clicking “CPU system setting” and then “Power off holding” in KV STUDIO. ^6 Reference value of input current. ^7 The input response time corresponding to the input time constant can be calculated as shown below. (Response time) = (Circuit delay of the input circuit) + (Delay by the digital filter) Example: Maximum response time when the input time constant is set to 10 μs OFF to ON: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs ON to OFF: 2 μs (circuit delay) + 2 μs (digital filter) = 4 μs Example: Maximum response time when the input time constant is set to 500 μs OFF to ON: 30 μs (circuit delay) + 400 μs (digital filter) = 430 μs ON to OFF: 50 μs (circuit delay) + 400 μs (digital filter) = 450 μs ^8 If an overcurrent occurs, protection operation (output turned OFF) and automatic recovery are repeated for all outputs within the shared common until the cause of the problem is removed.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Need More?

Contact Us

You can call, email, or chat us
we're here to support your business.

(847) 242-1595

Chat

support@plc-direct.com

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator