Keyence

FD-G50 Keyence

Specifications

Model			FD-G50
Pipe size	DN (Diameter Nominal)		32 A, 40 A, 50 A
	NPS (Nominal Pipe Size)		1 1/4", 1 1/2", 2"
	Outer diameter of pipe		ø41 to 45 mm 1.61" to 1.77", ø47 to 51 mm 1.85" to 2.01", ø58 to 62 mm 2.28" to 2.44"
	Pipe thickness		2.4 to 5.7 mm 0.09" to 0.22"
Supported pipe materials			Iron, steel, stainless steel
Supported fluids			Air, Nitrogen, other gases^*1
Fluid temperature			0 to 60ºC 32 to 140 °F
Recommended pressure			0.4 MPa or greater (58 PSI or greater)
Rated velocity of flow range			Up to 15 m/s
Actual flow rate range (typical)	m³/h		Pipe size 32 A: 54.00 Pipe size 40 A: 72.00 Pipe size 50 A: 120.00
	L/min		Pipe size 32 A: 900.0 Pipe size 40 A: 1200.0 Pipe size 50 A: 2000.0
	CFM		Pipe size 32 A: 32.00 Pipe size 40 A: 42.00 Pipe size 50 A: 70.00
Standard flow rate range (typical) [CFM]	20°C 68°F 60 psi 0.41 MPa		Pipe size 32 A: 151.58 Pipe size 40 A: 198.95 Pipe size 50 A: 331.58
	20°C 68°F 80 psi 0.55 MPa		Pipe size 32 A: 192.17 Pipe size 40 A: 252.22 Pipe size 50 A: 420.37
	20°C 68°F 100 psi 0.69 MPa		Pipe size 32 A: 232.76 Pipe size 40 A: 305.49 Pipe size 50 A: 509.16
	20°C 68°F 120 psi 0.83 MPa		Pipe size 32 A: 273.35 Pipe size 40 A: 358.77 Pipe size 50 A: 597.95
Display			QVGA 2.2" LCD color monitor
Display update cycle			Approx. 3 Hz
Display resolution	Instantaneous flow rate		0.01 m³/h, 0.1 L/min, 0.01 CFM
	Consumption/leakage amount		0.01 m³, 1 L, 0.1 CF
Response time			1.0 s/2.5 s/5.0 s/10.0 s/30.0 s/60.0 s/120.0 s/200.0 s (variable)
Measurement accuracy	Between 10 and 100% of F.S.		±2.0% of RD^2^3^4^5
	Between 1 and 10% of F.S.		±1.0% of F.S.^2^3^4^5
Zero point error			±0.15% of F.S.^2^6
Static leakage repeatability			±1.0% of RD^4^7
Hysteresis			Variable
Flow units			CFM(S), CFM, m³/h (N), m³/h (S), m³/h, L/min (N), L/min (S), L/min
I/O wiring connection port			M12 4-pin connector (male)
Detection mode (switchable)	ch.1		Instantaneous flow mode/area mode/pulse (+) mode/integrated flow mode/warning mode (consump)^*8
	ch.2		Instantaneous flow mode/area mode/pulse (−) mode/warning mode (leak)/error output mode/analog output/integrated flow reset/flow rate zero input/origin adjustment input^*8
Standard I/O (switchable)	Control output (ch.1/ch.2)		NPN/PNP setting switchable, open collector output 30 VDC or less, max. 100 mA/ch, residual voltage: 2.5 V or less
	Analog output (ch.2)		4 to 20 mA/0 to 20 mA, load resistance: 500 Ω or less
	External input (ch.2)		Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit			Power supply reverse connection protection, power supply surge protection, short-circuit protection for each output, surge protection for each output
Analog input (for volume conversion)			M8 4-pin connector (female), analog current input (4 to 20 mA), input resistance: 100Ω or less
Power supplied to pressure sensor			Supply voltage: Equivalent to voltage applied to the FD-G, Supply current:70 mA or less (analog output of the pressure sensor included)
Communication interface	USB		USB 2.0
	Ethernet	Standard	IEEE 802.3u (100BASE-TX)
		Transmission rate	100 Mbps
		Cable	Category 5 or higher STP (shielded twisted pair) or UTP (unshielded twisted pair) cable
		Connector	M12 connector (female, D-code)
Network function			Modbus TCP, EtherNet/IP™, IO-Link^*9
Recording capacity	Consumption amount/ leakage amount		Approx. 5 years
	Events		100
Power supply	Power voltage		20 to 30 VDC including 10% ripple (P-P), Class 2
	Power consumption		350 mA or less at 20 V, 290 mA or less at 24 V, 230 mA or less at 30 V (load current excluded) (analog output of the pressure sensor excluded), 550 mA or less at 20 V, 490 mA or less at 24 V, 430 mA or less at 30 V (Maximum load current excluded) (analog output of the pressure sensor excluded)
Environmental resistance	Enclosure rating		IP65/67 (IEC 60529)^*10
	Ambient temperature		Detection head: −10 to +60°C 14 to 140°F (no freezing), display unit: −10 to +55°C 14 to 131°F (no freezing)
	Relative humidity		5 to 85%RH (no condensation)
	Vibration resistance		10 to 500 Hz, power spectral density: 0.816 G²/Hz, XYZ axes
	Shock resistance		100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Display unit		Body: PBT + coating, display: PMMA, Power supply port: SUS304-equivalent, Ethernet port: zinc nickel plating
	Detection head		Body: PPS/SUS304, rear surface: rubber
	Mounting/damping bracket		SUS304
Weight			Approx. 2.7 kg
^1 The gas must be uniform and capable of transmitting ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^2 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the type and status of the pipe and the type and temperature of the gas. ^3 This is the value when considering linearity + span error in a stable environment with a temperature of 25°C 77°F. ^4 Defined with stable velocity of flow distribution. Does not include pulsations and fluctuations in the velocity of flow distribution primarily attributable to the equipment. ^5 The linearity error characteristic due to the pipe is not included in this value. ^6 It is possible to reduce zero point errors by performing an origin adjustment. ^7 This is the value within the range where measurement accuracy is guaranteed. ^8 When Bi-directional is specified, the following functions cannot be used. The selection of the comparison view/leak ratio view/static leakage, the measurement/display of the leakage amount/integrated flow, the setting of the target value/warning set value, and money conversions. Also, the I/O settings are limited as shown below. • ch.1: Pulse(+) mode • ch.2: Pulse(-) mode, Error output mode, Integrated flow reset, Flow zero input, Origin adjustment input ^9 IO-Link: Compatible with specification v1.1/COM1 (4.8 kbps). IO-Link is a trademark or registered trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 The IP65/67 enclosure rating is lost when a USB connection is established.

16,203.00 kr

1-year warranty

FREE WORDWIDE SHIPPING

Est. delivery between and

Condition:

Sealed Surplus

SKU: FD-G50-Sealed

Sold out

0.00 kr

Never Used Surplus

SKU: FD-G50

5 verified stock

16,203.00 kr

Used

SKU: FD-G50-Used

Sold out

0.00 kr

Variant

Quantity:

Need More?

Specifications

Model			FD-G50
Pipe size	DN (Diameter Nominal)		32 A, 40 A, 50 A
	NPS (Nominal Pipe Size)		1 1/4", 1 1/2", 2"
	Outer diameter of pipe		ø41 to 45 mm 1.61" to 1.77", ø47 to 51 mm 1.85" to 2.01", ø58 to 62 mm 2.28" to 2.44"
	Pipe thickness		2.4 to 5.7 mm 0.09" to 0.22"
Supported pipe materials			Iron, steel, stainless steel
Supported fluids			Air, Nitrogen, other gases^*1
Fluid temperature			0 to 60ºC 32 to 140 °F
Recommended pressure			0.4 MPa or greater (58 PSI or greater)
Rated velocity of flow range			Up to 15 m/s
Actual flow rate range (typical)	m³/h		Pipe size 32 A: 54.00 Pipe size 40 A: 72.00 Pipe size 50 A: 120.00
	L/min		Pipe size 32 A: 900.0 Pipe size 40 A: 1200.0 Pipe size 50 A: 2000.0
	CFM		Pipe size 32 A: 32.00 Pipe size 40 A: 42.00 Pipe size 50 A: 70.00
Standard flow rate range (typical) [CFM]	20°C 68°F 60 psi 0.41 MPa		Pipe size 32 A: 151.58 Pipe size 40 A: 198.95 Pipe size 50 A: 331.58
	20°C 68°F 80 psi 0.55 MPa		Pipe size 32 A: 192.17 Pipe size 40 A: 252.22 Pipe size 50 A: 420.37
	20°C 68°F 100 psi 0.69 MPa		Pipe size 32 A: 232.76 Pipe size 40 A: 305.49 Pipe size 50 A: 509.16
	20°C 68°F 120 psi 0.83 MPa		Pipe size 32 A: 273.35 Pipe size 40 A: 358.77 Pipe size 50 A: 597.95
Display			QVGA 2.2" LCD color monitor
Display update cycle			Approx. 3 Hz
Display resolution	Instantaneous flow rate		0.01 m³/h, 0.1 L/min, 0.01 CFM
	Consumption/leakage amount		0.01 m³, 1 L, 0.1 CF
Response time			1.0 s/2.5 s/5.0 s/10.0 s/30.0 s/60.0 s/120.0 s/200.0 s (variable)
Measurement accuracy	Between 10 and 100% of F.S.		±2.0% of RD^2^3^4^5
	Between 1 and 10% of F.S.		±1.0% of F.S.^2^3^4^5
Zero point error			±0.15% of F.S.^2^6
Static leakage repeatability			±1.0% of RD^4^7
Hysteresis			Variable
Flow units			CFM(S), CFM, m³/h (N), m³/h (S), m³/h, L/min (N), L/min (S), L/min
I/O wiring connection port			M12 4-pin connector (male)
Detection mode (switchable)	ch.1		Instantaneous flow mode/area mode/pulse (+) mode/integrated flow mode/warning mode (consump)^*8
	ch.2		Instantaneous flow mode/area mode/pulse (−) mode/warning mode (leak)/error output mode/analog output/integrated flow reset/flow rate zero input/origin adjustment input^*8
Standard I/O (switchable)	Control output (ch.1/ch.2)		NPN/PNP setting switchable, open collector output 30 VDC or less, max. 100 mA/ch, residual voltage: 2.5 V or less
	Analog output (ch.2)		4 to 20 mA/0 to 20 mA, load resistance: 500 Ω or less
	External input (ch.2)		Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit			Power supply reverse connection protection, power supply surge protection, short-circuit protection for each output, surge protection for each output
Analog input (for volume conversion)			M8 4-pin connector (female), analog current input (4 to 20 mA), input resistance: 100Ω or less
Power supplied to pressure sensor			Supply voltage: Equivalent to voltage applied to the FD-G, Supply current:70 mA or less (analog output of the pressure sensor included)
Communication interface	USB		USB 2.0
	Ethernet	Standard	IEEE 802.3u (100BASE-TX)
		Transmission rate	100 Mbps
		Cable	Category 5 or higher STP (shielded twisted pair) or UTP (unshielded twisted pair) cable
		Connector	M12 connector (female, D-code)
Network function			Modbus TCP, EtherNet/IP™, IO-Link^*9
Recording capacity	Consumption amount/ leakage amount		Approx. 5 years
	Events		100
Power supply	Power voltage		20 to 30 VDC including 10% ripple (P-P), Class 2
	Power consumption		350 mA or less at 20 V, 290 mA or less at 24 V, 230 mA or less at 30 V (load current excluded) (analog output of the pressure sensor excluded), 550 mA or less at 20 V, 490 mA or less at 24 V, 430 mA or less at 30 V (Maximum load current excluded) (analog output of the pressure sensor excluded)
Environmental resistance	Enclosure rating		IP65/67 (IEC 60529)^*10
	Ambient temperature		Detection head: −10 to +60°C 14 to 140°F (no freezing), display unit: −10 to +55°C 14 to 131°F (no freezing)
	Relative humidity		5 to 85%RH (no condensation)
	Vibration resistance		10 to 500 Hz, power spectral density: 0.816 G²/Hz, XYZ axes
	Shock resistance		100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Display unit		Body: PBT + coating, display: PMMA, Power supply port: SUS304-equivalent, Ethernet port: zinc nickel plating
	Detection head		Body: PPS/SUS304, rear surface: rubber
	Mounting/damping bracket		SUS304
Weight			Approx. 2.7 kg
^1 The gas must be uniform and capable of transmitting ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^2 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the type and status of the pipe and the type and temperature of the gas. ^3 This is the value when considering linearity + span error in a stable environment with a temperature of 25°C 77°F. ^4 Defined with stable velocity of flow distribution. Does not include pulsations and fluctuations in the velocity of flow distribution primarily attributable to the equipment. ^5 The linearity error characteristic due to the pipe is not included in this value. ^6 It is possible to reduce zero point errors by performing an origin adjustment. ^7 This is the value within the range where measurement accuracy is guaranteed. ^8 When Bi-directional is specified, the following functions cannot be used. The selection of the comparison view/leak ratio view/static leakage, the measurement/display of the leakage amount/integrated flow, the setting of the target value/warning set value, and money conversions. Also, the I/O settings are limited as shown below. • ch.1: Pulse(+) mode • ch.2: Pulse(-) mode, Error output mode, Integrated flow reset, Flow zero input, Origin adjustment input ^9 IO-Link: Compatible with specification v1.1/COM1 (4.8 kbps). IO-Link is a trademark or registered trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 The IP65/67 enclosure rating is lost when a USB connection is established.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Specifications

Model			FD-G50
Pipe size	DN (Diameter Nominal)		32 A, 40 A, 50 A
	NPS (Nominal Pipe Size)		1 1/4", 1 1/2", 2"
	Outer diameter of pipe		ø41 to 45 mm 1.61" to 1.77", ø47 to 51 mm 1.85" to 2.01", ø58 to 62 mm 2.28" to 2.44"
	Pipe thickness		2.4 to 5.7 mm 0.09" to 0.22"
Supported pipe materials			Iron, steel, stainless steel
Supported fluids			Air, Nitrogen, other gases^*1
Fluid temperature			0 to 60ºC 32 to 140 °F
Recommended pressure			0.4 MPa or greater (58 PSI or greater)
Rated velocity of flow range			Up to 15 m/s
Actual flow rate range (typical)	m³/h		Pipe size 32 A: 54.00 Pipe size 40 A: 72.00 Pipe size 50 A: 120.00
	L/min		Pipe size 32 A: 900.0 Pipe size 40 A: 1200.0 Pipe size 50 A: 2000.0
	CFM		Pipe size 32 A: 32.00 Pipe size 40 A: 42.00 Pipe size 50 A: 70.00
Standard flow rate range (typical) [CFM]	20°C 68°F 60 psi 0.41 MPa		Pipe size 32 A: 151.58 Pipe size 40 A: 198.95 Pipe size 50 A: 331.58
	20°C 68°F 80 psi 0.55 MPa		Pipe size 32 A: 192.17 Pipe size 40 A: 252.22 Pipe size 50 A: 420.37
	20°C 68°F 100 psi 0.69 MPa		Pipe size 32 A: 232.76 Pipe size 40 A: 305.49 Pipe size 50 A: 509.16
	20°C 68°F 120 psi 0.83 MPa		Pipe size 32 A: 273.35 Pipe size 40 A: 358.77 Pipe size 50 A: 597.95
Display			QVGA 2.2" LCD color monitor
Display update cycle			Approx. 3 Hz
Display resolution	Instantaneous flow rate		0.01 m³/h, 0.1 L/min, 0.01 CFM
	Consumption/leakage amount		0.01 m³, 1 L, 0.1 CF
Response time			1.0 s/2.5 s/5.0 s/10.0 s/30.0 s/60.0 s/120.0 s/200.0 s (variable)
Measurement accuracy	Between 10 and 100% of F.S.		±2.0% of RD^2^3^4^5
	Between 1 and 10% of F.S.		±1.0% of F.S.^2^3^4^5
Zero point error			±0.15% of F.S.^2^6
Static leakage repeatability			±1.0% of RD^4^7
Hysteresis			Variable
Flow units			CFM(S), CFM, m³/h (N), m³/h (S), m³/h, L/min (N), L/min (S), L/min
I/O wiring connection port			M12 4-pin connector (male)
Detection mode (switchable)	ch.1		Instantaneous flow mode/area mode/pulse (+) mode/integrated flow mode/warning mode (consump)^*8
	ch.2		Instantaneous flow mode/area mode/pulse (−) mode/warning mode (leak)/error output mode/analog output/integrated flow reset/flow rate zero input/origin adjustment input^*8
Standard I/O (switchable)	Control output (ch.1/ch.2)		NPN/PNP setting switchable, open collector output 30 VDC or less, max. 100 mA/ch, residual voltage: 2.5 V or less
	Analog output (ch.2)		4 to 20 mA/0 to 20 mA, load resistance: 500 Ω or less
	External input (ch.2)		Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit			Power supply reverse connection protection, power supply surge protection, short-circuit protection for each output, surge protection for each output
Analog input (for volume conversion)			M8 4-pin connector (female), analog current input (4 to 20 mA), input resistance: 100Ω or less
Power supplied to pressure sensor			Supply voltage: Equivalent to voltage applied to the FD-G, Supply current:70 mA or less (analog output of the pressure sensor included)
Communication interface	USB		USB 2.0
	Ethernet	Standard	IEEE 802.3u (100BASE-TX)
		Transmission rate	100 Mbps
		Cable	Category 5 or higher STP (shielded twisted pair) or UTP (unshielded twisted pair) cable
		Connector	M12 connector (female, D-code)
Network function			Modbus TCP, EtherNet/IP™, IO-Link^*9
Recording capacity	Consumption amount/ leakage amount		Approx. 5 years
	Events		100
Power supply	Power voltage		20 to 30 VDC including 10% ripple (P-P), Class 2
	Power consumption		350 mA or less at 20 V, 290 mA or less at 24 V, 230 mA or less at 30 V (load current excluded) (analog output of the pressure sensor excluded), 550 mA or less at 20 V, 490 mA or less at 24 V, 430 mA or less at 30 V (Maximum load current excluded) (analog output of the pressure sensor excluded)
Environmental resistance	Enclosure rating		IP65/67 (IEC 60529)^*10
	Ambient temperature		Detection head: −10 to +60°C 14 to 140°F (no freezing), display unit: −10 to +55°C 14 to 131°F (no freezing)
	Relative humidity		5 to 85%RH (no condensation)
	Vibration resistance		10 to 500 Hz, power spectral density: 0.816 G²/Hz, XYZ axes
	Shock resistance		100 m/s², 16 ms pulse, XYZ axes, 1000 times for each axis
Material	Display unit		Body: PBT + coating, display: PMMA, Power supply port: SUS304-equivalent, Ethernet port: zinc nickel plating
	Detection head		Body: PPS/SUS304, rear surface: rubber
	Mounting/damping bracket		SUS304
Weight			Approx. 2.7 kg
^1 The gas must be uniform and capable of transmitting ultrasonic waves. Measurement may be unstable due to the pressure inside of the pipe and the type of gas. ^2 This value is guaranteed by KEYENCE inspection facilities. Errors will be introduced by factors such as the type and status of the pipe and the type and temperature of the gas. ^3 This is the value when considering linearity + span error in a stable environment with a temperature of 25°C 77°F. ^4 Defined with stable velocity of flow distribution. Does not include pulsations and fluctuations in the velocity of flow distribution primarily attributable to the equipment. ^5 The linearity error characteristic due to the pipe is not included in this value. ^6 It is possible to reduce zero point errors by performing an origin adjustment. ^7 This is the value within the range where measurement accuracy is guaranteed. ^8 When Bi-directional is specified, the following functions cannot be used. The selection of the comparison view/leak ratio view/static leakage, the measurement/display of the leakage amount/integrated flow, the setting of the target value/warning set value, and money conversions. Also, the I/O settings are limited as shown below. • ch.1: Pulse(+) mode • ch.2: Pulse(-) mode, Error output mode, Integrated flow reset, Flow zero input, Origin adjustment input ^9 IO-Link: Compatible with specification v1.1/COM1 (4.8 kbps). IO-Link is a trademark or registered trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 The IP65/67 enclosure rating is lost when a USB connection is established.

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

FD-G50 Keyence

Specifications

Specifications

Specifications

FD-G50 Keyence

Specifications

Specifications

Trusted By

You may also like

Recently viewed