Vision Systems

Keyence OP-88574 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SI-F1003 Keyence

12,593.00 kr

Only 2 units left

Specifications

Model			SI-F1003^*1
Type			Main Controller Separate type^*2
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec
Terminal block	Laser remote interlock input		Non-voltage or voltage input ^3.^4
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*4
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*4
	Alarm output		NPN open-collector output (N.C.)^*4
	General comparator output		NPN open-collector output ^5^4
Expansion connector	TIMING2 input		Non-voltage or voltage input ^3.^4
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*4
	Alarm output		NPN open-collector output (N.C.)^*4
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*4
		Strobe output	NPN open-collector output ^5^4
		Binary selection output
		Binary selection input	Non-voltage or voltage input ^3.^4
RS-232C interface			Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface			In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface			100BASE-TX/10BASE-T
Major functions			12 Out simultaneous measurementcalculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory,interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*6
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 The SI-F1003 can be used independently, The measured value display and setting change can be done with the display panel(SI-FD500) and setup support software(SI-H3). ^2 The SI-F1001 can be used independently. The measured value display and setting change can be done with the display panel (SI-FD500) and setup support software (SI-H1). ^3 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^4 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^5 The rating of the NPN open-collector: 50 mA max. (40 V max.), residual voltage of 0.5 V max. The rating of the PNP open collector: 50 mA max. (30 V max.), residual voltage of 0.5 V max. ^6 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Keyence GL-VM56HP Keyence

10,502.00 kr

In stock, 11 units

Specifications

Model			GL-VM56HP
Beam axis spacing/Lens diameter			20 mm 0.79": ø5 ø0.197"
Number of beam axes			56
Total length			1120 mm 44.09"
Detection height			1100 mm 43.31"
Protection height			1145 mm 45.08"
Minimum detectable object size			ø25 mm ø0.98" ^*1
Detecting distance			0.3 to 15 m 1.0' to 49.2' ^*2
Effective angular aperture			Up to ±2.5° (3 m 9.8' or above)
Light source			Infrared LED (850 nm) Exempt Group (IEC62471)
Detection mode			ON when all beam axes received
Synchronization method			Optical synchronization
Interference prevention function			Interference prevention up to 2 units by series connection and switch setting
Control output (OSSD output)	Output type		Transistor output ×2 (PNP/NPN)
	Maximum load current		150 mA or less
	Residual voltage (when ON)		Up to 2.5 V (with 5 m 16.4' cable)
	OFF voltage		Up to 2.0 V (with 5 m 16.4' cable)
	Leakage current		Up to 0.8 mA
	Maximum load capacity		0.8 μF
	Load wiring resistance		Up to 2.5Ω
Protection circuit			Power supply reverse connection protection, short circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS	IEC/EN61496-1, UL61496-1
		EMI	EN55011 Class A, FCC Part15B Class A, ICES-003 Class A
	Safety		IEC61496-1/EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2/EN61496-2, UL61496-2 (Type 4 AOPD) EN ISO13849-1 (Category 4, PL e) IEC61508/EN61508 (SIL3) UL60947-1 / CSA C22.2 No. 60947-1 UL1998
Response time (OSSD)	With channel 0	ON→OFF	6.1
		OFF→ON	48.7 ^*3
		All blocked→ON	57.2 ^*4
	With channel A or B	ON→OFF	18.4
		OFF→ON	67.5 ^*3
		All blocked→ON	93.4 ^*4
Inputs			Short circuit current: Approx. 3 mA
Power supply	Power voltage		24 VDC -20/+25% 10% ripple (P-P) or less, class 2
	Current consumption (at maximum) (mA) Indicator : Standard / Eco/ External control	Transmitter	129 ^*5
		Receiver	140 ^*5
	Current consumption (at maximum) (mA) Indicator : OFF	Transmitter	58 ^*5
		Receiver	62 ^*5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient light		Incandescent lamp: 3000 lux or less, sunlight: 20,000 lux or less
	Operating ambient temperature		-30 to +55°C -22 to +131°F (no freezing) ^*6
	Operating relative humidity		Up to 95%RH (no condensation)
	Storage temperature		-30 to +70°C -22 to +158°F (no freezing)
	Storage relative humidity		Up to 95% RH
	Overvoltage category		ll
	Vibration resistance		5 to 150 Hz 1G 10 cycles each in X, Y, and Z axes
	Shock resistance		15 G 6 ms pulses 100 times each in X, Y, and Z axes
Material	Main unit case		Aluminum alloy
	Upper case/lower case		PPS (GF40%)
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		730 g 25.76 oz
	Receiver		740 g 26.12 oz
	Total		1470 g 51.89 oz
^1 The maximum operating speed of the detected object is 2.0 m 6.6'/s. ^2 When the optional front protection cover is attached to either the transmitter or receiver, the detecting distance is shortened by 0.5 m 1.6'. When attached to both, it is shortened by 1 m 3.3'. ^3 If light blocking time is 80 ms or less, the response time (OFF>ON) will be slowed down to a minimum of 80 ms to ensure that the OSSD remains OFF for 80 ms or more. ^4 “All blocked > ON” is the time it takes for the transmitter and receiver to turn ON from an unsynchronized state (both upper and lower end beam axes are blocked). Since the reception or blockage of light is determined after the transmitter and receiver are synchronized, the response time is long. ^5 The current of control output (OSSD) is not included. ^6 When the ambient operating temperature is between 50 and 55°C 122°F and 131°F, set the indicator mode to Light OFF mode.

Keyence GL-RCG03S Keyence

4,621.00 kr

Only 1 unit left

Specifications

Model				GL-RCG03S
Number included				incl. 1 set
Length				0.3 m 1.0'
Note				One set connects to both transmitter and receiver.
Weight				Approx.60 g

Keyence OP-88458 Keyence

0.00 kr

Sold Out

Specifications

Model				OP-88458
Weight				Approx. 28 g 0.98 oz

Keyence XC-T34B2 Keyence

0.00 kr

Sold Out

Specifications

Model		XC-T34B2
Rated voltage		125 VAC/DC
Rated current		1 A/pin
Ambient operating temperature		−40 to +80°C −40 to +176°F
Screw torque		0.8 N·m (max.)
Applicable wire diameter		AWG22 to 16
Environmental resistance	Insulation resistance	500 VDC, 1000 MΩ or greater
	Withstand voltage	500 VAC, 1 minute, 1 mA or less

Keyence OP-88007 Keyence

0.00 kr

Sold Out

Specifications

Model				OP-88007
Type				USB-mini cable
Length				2 m 6.6'

Keyence SV-C3E Keyence

0.00 kr

Sold Out

Specifications

Model				SV-C3E
Type				Motor power cable, Standard
Length				3 m 9.8'
Note				for 2 kW motor

Keyence XG-X1500 Keyence

45,129.00 kr

Only 9 units left

Buy the Keyence XG-X1500 - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence XG-X1500 is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence OP-87905 Keyence

2,198.00 kr

Only 5 units left

Specifications

Model				OP-87905
Type				Cable between sensor head amplifier
Length				10 m 32.81'
Weight				Approx. 400 g

Keyence DX-RH1GA Keyence

0.00 kr

Sold Out

Specifications

Model		DX-RH1GA
Display	Charging Confirmation LED	2-color LED
Operations	Hard Keys	Trigger key × 1
RFID	Supported Tags	ISO/IEC 18000-6 Type C (EPC Global Class 1 Gen 2)
	Frequency Range	902.75 - 927.25 MHz
	Transmission Output	1 W or less
Power Source	Type	Dedicated lithium ion battery pack (DX-BC6)
	Capacity	6270 mAh
Interfaces	Magnet Connector	Supported (charging/communication) * Connected to DX-UC4 (with the DX-KE1), DX-UC4E, DX-UC1UL, DX-UC1M, or OP-88604 (magnetic charging cable)
Dimensions		182.1 × 100 × 152.4 mm 7.17" × 3.94" × 6.00"
Weight		Approx. 405 g 14.30 oz

Keyence OP-88325 Keyence

18,076.00 kr

Only 3 units left

Buy the Keyence OP-88325 - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence OP-88325 is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence KV-C10 Keyence

3,574.00 kr

Only 1 unit left

Specifications

Model				KV-C10
Type				Camera cable
Length				10 m 32.8'

Keyence GL-R36H-T Keyence

14,663.00 kr

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence KV-SC20 Keyence

5,475.00 kr

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence OP-87098 Keyence

0.00 kr

Sold Out

Specifications

Model				OP-87098
Type				Fiber Cutter (Gray)
Overview				Cutter for free-cut fiber units. (Attached to free-cut fiber units.)
Applicable product				FU
Material				ABS, stainless

Keyence GS-H02 Keyence

5,048.00 kr

Only 1 unit left

Specifications

Model				GS-H02
Weight				Approx. 90 g

Keyence FD-MZ50AYK Keyence

18,118.00 kr

Only 3 units left

Specifications

Model		FD-MZ50AYK^*1
Type		Horizontal
Shape		Built-in amplifier
Rated flow range		0.7 - 13.0 G/min (2.5 - 50 L/min)^*1
Possible display range		0.7 - 26.4 G/min (2.5 - 100 L/min)^*2
Possible ranges to set		0 - 26.4 G/min (0 - 100 L/min)
Connection port		NPT3/4 (20 A)
Detectable fluids		Water or non-corrosive liquid
Conductivity of detection fluids		5 µS/cm or higher
Detection fluid temperature		0 to +85°C 32 to 185 °F (No freezing)
Pressure loss		Max. 1.45 PSI (0.01 MPa)
Display method		Dual row display with 4-digit, 7 segment LED, bar display (2 colors), output indicators, flow indicator
Display resolution		0.1/1 (G/min, L/min) selectable
Repeatability		0.5 s : ±5% of F.S., 1 s : ±3.5% of F.S., 2.5 s : ±2.5% of F.S., 5 s : ±1.6% of F.S., 10 s : ±1% of F.S., 30 s : ±0.8% of F.S., 60 s : ±0.6% of F.S.^*3
Hysteresis		Variable
Response time (chatter prevention feature)		0.5 s/1 s/2.5 s/5 s/10 s/30 s/60 s variable
Accumulated flow unit		0.1/1/10/100/1000 (G, L) selectable
Integration data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length : 10 years or longer, Data read/write frequency : 1 million times or more)
Analog output		4-20 mA, max. load resistance 260 Ω Analog output range can be set to any value
Integration reset/bank switch input/flow zero function input		Input time : 20 ms or greater,Select either the accumulation output or the accumulation pulse by setting the mode
Power consumption (Current consumption)		Normal : 1700 mW (70 mA), Power save : 1000 mW (40 mA)
Rating	Power voltage	24 VDC, Ripple (P-P) 10 % or less, Class 2
Environmental resistance	Enclosure rating	IP65
	Pressure resistance	290 PSI (2.0 MPa)
	Applied pressure range	Max. 145 PSI (1.0 MPa)
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material	Liquid end materials	Bore : SCS13, Measurement pipe : PPS, O ring : fluoro-rubber (FKM)
	Other materials	Plastic case areas : PPS, Metal case areas : SUS430, Cable : PVC
Accessory		Instruction Manual, Connector cable (2.7 m 106.3")
Weight		Approx. 1,130 g
^1 The rated flow range indicates recommended operating range. ^2 Can be used within the display range as well as within the rated flow range. ^*3 The repeatability is effective within the display range. Convert the F.S. (full scale) listed in the table according to the rated flow range.

Keyence CV-S035MH (CV-S035M) Keyence

0.00 kr

Sold Out

Specifications

Model		CV-S035MH
Type		Camera^*1
Image element		1/3-inch monochrome CCD image receiving element, 2x high-speed reading using square-pixel, 350000 pixels Unit cell size: 7.4 x 7.4 µm
Valid pixel count		320,000 pixels 656 (H) x 492 (V) ^*2
Pixel transfer frequency		24.5 MHz
Scanning system		progressive (16.0ms), interlace (8.8ms)
Transfer system		Digital serial transfer
Electronic shutter		1/15, 1/30, 1/60, 1/120, 1/240, 1/500, 1/1000, 1/2000, 1/5000, 1/10000, 1/20000, 0.05 msec to 9000 msec can be set with numeric values
Lens mount		Special mount (M10.5 P0.5 male)
Environmental resistance	Ambient temperature	Head: 0 to +50 °C 32 to 122 °F, relay unit: 0 to +40 °C 32 to 104 °F
	Relative humidity	35 to 85 % RH (No condensation)
Weight		Head: Approx. 160 g (including the cable, not the lens) Relay unit: Approx. 70 g
^1 The CA-CN17 camera cable (17M) and the CA-CN17R high-flex camera cable (17M) cannot be used. ^2 In 310,000-pixel mode, 310,000 pixels (640 x 480) serve as the processing area. In 240,000-pixel mode, 240,000 pixels (512 x 480) serve as the processing area.

Keyence SV2-M200AK Keyence

42,474.00 kr

Only 4 units left

Specifications

Model				SV2-M200AK
General specifications	Applicable servo amplifier			SV2-200L2
	Rated output			1.8 kW
	Rated torque			11.5 N·m ^*1
	Instant maximum torque			28.7 N·m
	Rated current			16.7 Arms
	Instant maximum current			42 Arms
	Rated rotation speed			1500 min^-1
	High rotation speed			3000 min^-1
	Torque constant			0.748 N·m/Arms
	Rotor moment of inertia			26.0 ×10^-4kg·m²
	Rated power rating			50.9 kW/s
	Rated angle acceleration			4420 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		22 bits
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole area)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or more)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20 to 80% RH (no condensation)
		Operating atmosphere		Indoors (no corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2000 m 6561.7' or less (reduced ratings at 1000 m 3280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8'/s² with servo motor flange surface as reference (up/down, left/right) 24.5 m/s² 80.4'/s² (forward/backward)
		Impact resistance		490 m/s² 1607.6'/s² with servo motor flange surface as reference, 2 times
	Isolation rank			phase F
	Min. insulation resistance			500 VDC, 10 MΩ or more with insulation resistance tester
	Isolation voltage tolerance			1500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Allowable load inertia moment			5 ×
	Approx. weight			8.8 kg
^*1 50 W to 750 W rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W / 100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink.

Keyence AH-290 Keyence

0.00 kr

Sold Out

Specifications

Model			AH-290
Type			Sensor head
Amplifier unit			―
Shape			Cylindrical, diameter: 90
Measuring range			0 to 35 mm 1.38"
Analog output voltage	Output voltage		0 to 7V
	Straight line range		―
	Impedance		100 Ω
	Resolution		0.1% of F.S.
	Linearity		±1.0% of F.S.
	Response		-1.5 VDC
Temperature fluctuation	Sensor head		0.08% of F.S./°C^*1
Temperature characteristics	Amplifier unit		―^*1
Rating	Power voltage		110/120/220/240 VAC ±10 %, 50/60 Hz
	Power consumption		6VA
Environmentalresistance	Enclosure rating	Sensor head	―
	Operating ambient temperature		-10 to +60°C 14 to 140°F
		Amplifier unit	―
Environmental resistance	Relative humidity		35 to 85 % RH (No condensation)
Weight	Sensor head		―
Weight (including cord)	Amplifier unit
^*1 When the distance between the sensor head and the target is within 50% of the measurement range.

Keyence KV-C64TCP Keyence

4,794.00 kr

Only 2 units left

Specifications

Model		KV-C64TCP
Type		Output unit
External connection method		Connector (MIL standard)^*1
Output	Number of outputs	64 points
	Output mode	Transistor (source)
	Rated load	30 VDC, 0.2 A
	Leakage current at OFF	100 μA or less
	Residual voltage at ON	0.5 V or less
	ON resistance	-
	Common method	64 points/1 common (4 terminals)^*2
	Operation time	OFF to ON: 50 μs or less,ON to OFF: 200 μs or less
Internal current consumption		100 mA or less
Weight		Approx. 140 g
^1 Connectors for connector-type I/O units are not included XC Series Terminal Block Conversion Unit is available. ^2 Although KV-C64TD and KV-C64TCP have four points, they are the same internally.

Keyence GP-M400 Keyence

4,669.00 kr

Only 5 units left

Specifications

Model			GP-M400
Rated pressure			0 to+5802 PSI (0 to+40 MPa)
Possible display range			-580 to+6382 PSI (-4.00 to+44.00 MPa)
Zero-cut pressure value			±0.5% of F.S.
Burst pressure			14504 PSI (100 MPa)
Display resolution	kPa		None
	MPa		0.01
	PSI		1
	bar		0.1
	kgf/cm²
Fluid type			Liquid that will not corrode the liquid contact part
Type of pressure			Gage pressure
Precision			±1.0% of F.S. or less^*1
Repeatability			±0.3% of F.S. or less^*2
Temperature characteristics			±0.6% of F.S./10°C 50°F
Connection port			G3/4 (Changes to the R male 1/8, R male 1/4, R male 3/8, G female 1/4, NPT male 1/8, and NPT male 1/4 option adapters are available.)
Box rotation angle			Maximum 330°
Medium temperature			-20 to +100°C -4°F to +212°F (no freezing/condensation)^*3
Power voltage			10-30 VDC, Ripple (P-P): 10% max, Class 2 or LPS
Current consumption			50 mA or less (when 24 V: 32 mA or less, when 12 V: 48 mA or less. Not including load)^*4
Display method			4 column, digital LED, red/Vertical inversion display possible
Operation display light			Operation indicator (output 1) (orange), Operation indicator (output 2) (orange)
Hysteresis			During hysteresis mode: variable (Difference between switch-on point and switch-off point is hysteresis) During window mode: fixed (0.5% of F.S.)
Response	Control output		Selectable from 3 to 5000 ms
	Analog output		As above + 2 ms (90% response)
Output	Output 1 control output		NPN/PNP open collector (Selectable), Max. 250 mA (30 V max) Main unit residual voltage 1 V max, N.O./N.C. selectable
	Output 2 replacement type	Control output
		Analog output	4-20 mA, maximum load resistance 500 Ω (When the electric voltage is more than 20 V)^*5
Environmental resistance	Enclosure rating		IP67
	Pressure resistance		50 MPa (500 bar)
	Ambient temperature		-20 to +80 °C -4 to 176 °F (No freezing and no condensation)
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		IEC60068-2-6 20 G (10 to 2000 Hz, 2 hours each in the X, Y, and Z axis)
	Shock resistance		IEC60068-2-27 50G (11 ms, 3 times for each of X, Y and Z direction)
Material properties	Wetted part		Pressure port: SUSXM7, Diaphragm pressure port: Al₂O₃ (Alumina), O ring: FKM
	Other parts		Housing metal portion: SUS304, SUS303, Housing plastic portion: PPSU
Applicable cable			M12 connector 4 pin
Weight			Approx. 150 g
^1 This is the value when considering linearity + hysteresis + repeatability in a stable environment of 23°C 73°F. ^2 The repeatability, based on consistent conditions, is the variation in the value that will be displayed. ^3 When the temperature of the piping exceeds 80°C 176°F, do not connect the cable. ^4 Consumption current including output is 0.6 A and under. ^*5 The maximum load resistance R will be the values below in response to the electric voltage E. When 10-23V: R = ｛38 x (E-10) + 128｝ Ω When 23-30V: R = 622 Ω

Keyence GL-RPT10PM Keyence

4,934.00 kr

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.