Process Controls / Process Sensors

Showing 577 - 586 of 586 products

0.00 kr

Sold Out

Specifications

Model				FD-HCB10G
Cable end				M12, 8-pin female - 6-core cable
Length				10 m 32.8'
Material				PVC
Weight				Approx. 420 g

Keyence FD-HB1 Keyence

0.00 kr

Sold Out

Specifications

Model				FD-HB1
Material				SUS304
Weight				Approx. 65 g 2.29 oz

Keyence FD-XA2 Keyence

7,541.00 kr

Only 5 units left

Specifications

Model		FD-XA2
Type		DIN rail type, expansion unit
Display method		Output indicator, 4-digit 7 segment display, OLED, Stability level display
Display refresh frequency		Instantaneous flow: approx. 5 times/second, Discharge amount/Accumulated flow approx. 30 times/second
Response time		50 ms/100 ms/500 ms/1 s/2.5 s/5 s/10 s/30 s/60 s (selectable, default: 500 ms)
Integration data storage interval		Written to the memory every 10 seconds
Memory back up		EEPROM (data storage period: more than 10 years, number of data rewritable times: 1 million times or more) ^*1
Detection mode	ch.1	Instantaneous flow rate mode/Area mode/Pulse output (+) mode/Integrated flow mode/Shot mode (selectable)
	ch.2	Instantaneous flow rate mode/Area mode/Pulse output (-) mode/Shot mode/Error output mode/Bubble alert mode/Error + bubble alert mode (selectable)
Input/output	Output	NPN/PNP setting switch Open collector output: 30 V or lower, main unit: 50 mA or lower/ch.^*2/expansion unit: 20 mA or lower/ch., residual voltage: 2 V or lower
	Analog output	-
	External input	Flow rate zero input/shot sampling input/integrated flow reset input/zero shift input (selectable) Short circuit current: NPN 1 mA or lower/PNP 2 mA or lower, input time: 20 ms or longer
Network support		Supports NU series
Unit expansion		Up to 7^*3 per main unit
Protection circuit		Power supply reverse connection protection, power surge protection, output short circuit protection, output surge protection
Power supply	Power voltage	20 to 30 VDC including 10 % ripple (P-P) , Class 2
	Power consumption	185 mA or lower (including the sensor head, excluding the load current)
Environmental resistance	Ambient temperature	-10 to +50 °C (No freezing) 14 to 122 °F
	Relative humidity	35 % to 85 %RH (No condensation)
	Vibration resistance	10 - 55 Hz, double amplitude 1.5 mm 0.06 ", 2 hours each for X,Y,Z direction
	Shock resistance	100 m/s² (approx. 10 G) 16 ms pulse, 1000 times each for X,Y,Z direction
Material		Main body case/front sheet: PC, Key top: POM, Cable: PVC
Weight		Approx. 180 g
^1 Internal data from full time recording can be read via USB (Ver.2.0) communication. ^2 20 mA or lower/ch when adding expansion units. ^*3 Refer to the Instruction Manual for the number of connected units to N-bus devices.

Keyence OP-26751 Keyence

1,122.00 kr

Only 9 units left

Specifications

Model				OP-26751
Type				End unit
Overview				Used to secure the amplifier when main and expansion units are additionally set.
Applicable product				Expansion type sensor amplifier including FS-N10 Series.
Number included				2 pcs.
Material				Polycarbonate, stainless steel, Screw: Steel (Nickel plated)
Note				When adding sensor amplifier, use DIN rail and surely use end unit at both ends.

Keyence MU-N12 Keyence

3,860.00 kr

Only 5 units left

Specifications

Model		MU-N12
Main unit/Expansion unit		Expansion unit
Response time		Depends on the connected sensor model^*1
Expansion units		Up to 4 expansion units^*2
I/O	Control output	4 max., NPN open collector/PNP open collector selectable, 24 V or less, Main unit: 50 mA or less^3, Expansion unit: 20 mA or less, Residual voltage: 2 V or less, N.O./N.C. selectable ^1^*4
	External input	5 max., Short-circuit current: NPN: 1 mA or less, PNP: 2 mA or less, For the applied voltage, see wiring diagrams (page 3 of the instruction manual) ^1^4
	Analog output	-
Protection circuit		Protection against reverse power connection, power supply surge, output overcurrent, output surge, and reverse output connection
Power supply	Power voltage	24 VDC, ripple (P-P) 10% or less, Class 2 or LPS
	Current consumption	55 mA or less (without load)^*5
Sensor connection specification	Allowable sensor current	150 mA or less
N-bus connection specification	Allowable passing current	900 mA or less
Environmental resistance	Ambient temperature	-20 to +50 °C -4 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case and dust cover: Polycarbonate Buttons: Polyacetal Display panel: PMMA
Weight		Approx. 70 g
^1 The response time, as well as the types and number of inputs and outputs that are available, vary depending on the connected sensor model. For details, see the specific "MU-N Series User's Manual" for the model that will be connected. ^2 Up to 5 N-bus devices, including the main unit (or network unit), can be linked together. ^3 20 mA or less: When using the expansion unit. ^4 For more information on Control output, External input, and Analog output wire allocation, please refer to the table of "Power Cable Pin Layout" on page 3 of this manual. ^*5 1185 mA or less when a sensor is attached, 4 outputs (with loads) are used, and expansion units are connected.

Keyence MU-N11 Keyence

3,816.00 kr

Only 6 units left

Specifications

Model		MU-N11
Main unit/Expansion unit		Main unit
Response time		Depends on the connected sensor model^*1
Expansion units		Up to 4 expansion units^*2
I/O	Control output	4 max., NPN open collector/PNP open collector selectable, 24 V or less, Main unit: 50 mA or less^3, Expansion unit: 20 mA or less, Residual voltage: 2 V or less, N.O./N.C. selectable ^1^*4
	External input	5 max., Short-circuit current: NPN: 1 mA or less, PNP: 2 mA or less, For the applied voltage, see wiring diagrams (page 3 of the instruction manual) ^1^4
	Analog output	1 max., Current output/ Voltage output selectable, Current output: 4 to 20 mA, Max. load resistance: 450 Ω, Voltage output: 0 to 10 V, External load resistance: 5 kΩ or more ^1^4
Protection circuit		Protection against reverse power connection, power supply surge, output overcurrent, output surge, and reverse output connection
Power supply	Power voltage	24 VDC, ripple (P-P) 10% or less, Class 2 or LPS
	Current consumption	70 mA or less (without load)^*5
Sensor connection specification	Allowable sensor current	150 mA or less
N-bus connection specification	Allowable passing current	1200 mA or less
Environmental resistance	Ambient temperature	-20 to +50 °C -4 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 6 times in each of the X, Y, and Z directions
Material		Case and dust cover: Polycarbonate Buttons: Polyacetal Display panel: PMMA
Weight		Approx. 70 g
^1 The response time, as well as the types and number of inputs and outputs that are available, vary depending on the connected sensor model. For details, see the specific "MU-N Series User's Manual" for the model that will be connected. ^2 Up to 5 N-bus devices, including the main unit (or network unit), can be linked together. ^3 20 mA or less: When using the expansion unit. ^4 For more information on Control output, External input, and Analog output wire allocation, please refer to the table of "Power Cable Pin Layout" on page 3 of this manual. ^*5 1500 mA or less when a sensor is attached, 4 outputs (with loads) are used, and expansion units are connected.

Keyence FD-XS1E Keyence

22,292.00 kr

Only 5 units left

Specifications

Model			FD-XS1E
Supported pipe materials			Metal pipes, Plastic pipes (soft/hard) ^*1
Supported fluids			Liquids (water, oil, adhesive, grease, chemical solutions, etc.) ^*1
Supported fluid temperature			0 °C (no freezing on the pipe surface) to 100 °C 32 to 212 °F (Pipe surface temperature)
Clamp set model	Plastic pipe/tube attachment		FD-XC1R1, FD-XC1R2
	Metal pipe attachment		FD-XC1M^*2
Maximum rated flow rate			1000 mL/min
Zero cut flow rate			50 mL/min^*3 (variable, default)
Display resolution	Instantaneous flow rate		1/10 mL/min (Displayed on controller)
Repeatability			Response time 50 ms: ±20 % of RD Response time 500 ms: ±15 % of RD
Hysteresis			Variable
Display method			Status indicator
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529) , IP68G (JIS C0920) ^*4
	Ambient temperature		0 to 60 °C 32 to 140 °F (No freezing)
	Relative humidity		35 % to 85 %RH (No condensation)
	Vibration resistance		10 to 55 Hz, double amplitude 1.5 mm 0.06 ", 2 hours each for X,Y,Z direction
	Shock resistance		50 G 11 ms 3 times each for X,Y,Z direction
Material	Sensor head		Head body: PPS/PPSU, relay amplifier: PPS, cable: PVC, controller connector: PPS/PBT/POM
	Clamp set	For plastic pipe	Body, fixing screw: PPS, detection surface: special rubber, pipe support rubber: FKM, sensor head fixing screw: SUSXM7
		For metal pipe	Metal: SUS304/SUSXM7, detection surface: special rubber, clamp support rubber: FKM, sensor head fixing screw: SUSXM7
Weight			Approx. 230 g
^1 Liquid must allow for the passage of an ultrasonic pulse, as well as not contain large air pockets or excessive bubbles. Readings may become unstable depending on the type of pipe. ^2 When using stainless steel or iron pipes, the ideal pipe wall thickness is as follows, FD-XS1E: approx. 0.5 mm 0.02", FD-XS8E: approx. 1 mm 0.04", FD-XS20E: approx. 1 0.04" to 2 mm 0.08". FD-X signal strength and stability will decrease as the thickness of the pipe wall increases or decreases from the suggested size. ^3 The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate. ^4 The connector part of the sensor head cable is IP65/IP67.

Keyence FD-Q20C Keyence

4,853.00 kr

In stock, 11 units

Specifications

Model		FD-Q20C
Supported pipe diameter		1/2" (15 A), ø18 to ø23 (mm) 3/4" (20 A), ø23 to ø28 (mm)
Supported pipe materials		Metal pipe/Resin pipe^*1
Supported fluids		Various liquid [i.e. water (including DI), oils, chemicals, etc.]^*1
Supported fluid temperature		0 to 85°C 32 to 185°F (No freezing on the pipe surface)^*2
Maximum rated flow		1/2" (15 A): 60 L/min, 15.9 G/min 3/4" (20 A): 100 L/min, 26.4 G/min
Zero cut flow rate		2.5 L/min (Default)^*3
Display method		Status indicator, output indicator, dual row display with 4-digit, 7 segment LED, stability level indicator
Display update cycle		Approx. 3 Hz
Display resolution		0.1/ 1 (Default : 0.1) (L/min)
Response time		0.5 s / 1.0 s / 2.5 s / 5 s / 10 s / 30 s / 60 s
Protection circuit		Power supply reverse connection protection, power supply surge protection, each output short-circuit protection, each output surge protection
Repeatability		0.5 s : ±2.0%, 1 s:±1.5%, 2.5 s : ±1.0%, 5 s : ±0.5%, 10 s : ±0.35%, 30 s : ±0.2%, 60 s : ±0.15% (/F.S.^*4(Specific to selected response time))
Hysteresis		Variable
Integrated flow unit display		0.1/ 1/ 10/ 100/ 1000 (Default : 1) (L)
Integrated flow data storage cycle		Save to memory every 10 seconds
Memory backup		EEPROM (Data storage length: 10 years or longer, Data read/write frequency: 1 million times or more)
Power I/O connector		M12 4-pin connector
Input/Output (Selectable)	Output (ch.1/ch.2)	Control output/ Pulse output/ Error output (Selectable, Default : ch.1 control output/ ch.2 not used), NPN/PNP setting switchable,open collector output 30 V or less, max. 100 mA/ch., residual voltage 2.5 V or less^*5
	Analog output (ch.2)	4 to 20 mA / 0 to 20 mA (Selectable, Default: not used), load resistance 500 Ω or less^*5
	External input (ch.2)	Integrated flow reset input/ Flow rate zero input/ Origin adjustment input (Selectable, Default: not used), short-circuit current 1.5 mA or less, input time 20 ms or more^*5
Power supply	Power voltage	20 to 30 VDC , ripple (P-P) 10% max, Class2/LPS
	Current consumption	100 mA or less (Load current excluded)^*6
Environmental resistance	Enclosure rating	IP65/IP67 (IEC60529)
	Ambient temperature	-10 to +60 °C 14 to 140 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	100 m/s², 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Sensor main unit	PPS/PES/PBT/SUS303/SUS304/SUSXM7
	Sensor surface	Rubber
	Mounting bracket	SUS304/PA/SUSXM7
Weight		Approx. 400 g (including mounting bracket)
^1 Liquid must allow for the passage of an ultrasonic pulse, as well as not contain large air pockets or excessive bubbles. Detection may be unstable on certain non-standard pipes (i.e. lined pipes) ^2 Contact KEYENCE when the temperature of the pipe is greater than 85°C 185°F ^3 The zero cut flow rate can be changed in the settings. When using the unit with a low flow rate range, perform an origin adjustment when the fluid is not moving if you change the zero cut flow rate. ^4 This specification is valid when the flow velocity distribution is stable. This value does not take into account the effects of pulsation or fluctuations in flow velocity distribution due to facility factors. Convert the F.S. (full scale) listed in the table according to the rated flow range. ^5 IO-Link: Compatible with Specification v1.1 / COM2 (38.4 kbps) The setting file can be downloaded from the KEYENCE website. If using the unit in the environment where downloading the file is not possible via internet, contact your nearest KEYENCE office. IO-Link is either registered trademarks or trademarks of PROFIBUS Nutzerorganisation e.V. (PNO) ^6 When including the loads, please add 200 mA to this value.

Keyence FS-MC8P Keyence

2,946.00 kr

In stock, 54 units

Specifications

Model		FS-MC8P
Output		PNP
Response time		Depends on the response time settings of the connected expansion units
External input		Input time of the connected expansion units +11 ms
Number of inputs and outputs		Separate control outputs: 8, common output: 1, common input: 1
Unit expansion		Up to 8 expansion units can be connected. (However, each dual output type will be treated as 2 expansion units.) Allowable passing current: 1200 mA or less
Indicators		STATUS indicator (green and red two-color display) MEMORY indicator (orange) LOCK indicator (orange)
Separate control output, common output		PNP open-collector, 30 V or less, 20 mA or less per output, residual voltage: 1.6 V or less
Protection circuit		Protection against reverse power connection, reverse output connection, output overcurrent, and output surge
Power supply	Power voltage	10 to 30 VDC (including 10 % ripple (P-P) or less) , class 2 or LPS^*1
	Power consumption	690 mW or less (when used as a solitary unit) (26 mA or less at 24 V/38 mA or less at 12 V [excluding the load current] )^*2
Environmental resistance	Ambient temperature	-20 °C -4 °F to +55 °C +131 °F (no freezing)
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
	Shock resistance	500 m/s²; 3 times each for X, Y, and Z axes
Case material		Main unit and cover: polycarbonate
Weight		Approx. 110 g
^1 Match the rated power supply voltage of the expansion units to be connected to the system. ^2 The power consumption including the load when the maximum number of units are connected is 38 W max.

Keyence FS-MC8N Keyence

2,477.00 kr

In stock, 45 units

Specifications

Model		FS-MC8N
Output		NPN
Response time		Depends on the response time settings of the connected expansion units
External input		Input time of the connected expansion units +11 ms
Number of inputs and outputs		Separate control outputs: 8, common output: 1, common input: 1
Unit expansion		Up to 8 expansion units can be connected. (However, each dual output type will be treated as 2 expansion units.) Allowable passing current: 1200 mA or less
Indicators		STATUS indicator (green and red two-color display) MEMORY indicator (orange) LOCK indicator (orange)
Separate control output, common output		NPN open-collector, 30 V or less, 20 mA or less per output, residual voltage: 1.4 V or less
Protection circuit		Protection against reverse power connection, reverse output connection, output overcurrent, and output surge
Power supply	Power voltage	10 to 30 VDC (including 10 % ripple (P-P) or less) , class 2 or LPS^*1
	Power consumption	690 mW or less (when used as a solitary unit) (26 mA or less at 24 V/38 mA or less at 12 V [excluding the load current] )^*2
Environmental resistance	Ambient temperature	-20 °C -4 °F to +55 °C +131 °F (no freezing)
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
	Shock resistance	500 m/s²; 3 times each for X, Y, and Z axes
Case material		Main unit and cover: polycarbonate
Weight		Approx. 110 g
^1 Match the rated power supply voltage of the expansion units to be connected to the system. ^2 The power consumption including the load when the maximum number of units are connected is 38 W max.

Previous Page 25 / 25