Machine Vision Systems

0.00 kr

Sold Out

Specifications

Model				OP-88022^*1
Type				Small mounting bracket
Applicable product				LR-W70/WF10
Material				SUS304
Note				M3 screw × 2 supplied
Weight				Approx. 50 g
^*1 The 4-pin M12 connector type may not be mounted in the orientation shown in the picture (connector downward). Confirm the dimensions and surroundings carefully.

Keyence SZ-VPC03 Keyence

11,977.00 kr

Only 3 units left

Specifications

Model				SZ-VPC03^*1
Type				Quick Disconnect
Cable end				M12
Length				0.3 m 0.98'
Weight				Approx. 80 g
^*1 SZ-VPC03 is equipped with only 4 pins: 24 V, 0 V, OSSD1, OSSD2.

Keyence BT-CG64 Keyence

0.00 kr

Sold Out

Specifications

Model		BT-CG64
Dedicated AC adaptor specifications (OP-88389)	Input	100 to 240 VAC 50/60 Hz 70 VA
	Output	12 VDC 5.0 A maximum (60 W max.)
	Average active efficiency	89% or more
	Efficiency at low load (10%)	87% or more
	No-load power consumption	0.04 W
	Dimensions	110 x 62.0 x 31.5 mm (excluding the cable)
	Weight	Approx. 150 g (excluding the AC cable)
Environmental resistance	Ambient temperature	0 to +40°C (No freezing)
	Relative humidity	~ 85%RH (No condensation)
	Storage temperature	-20 to +60°C (No freezing)
	Storage relative humidity	~ 85%RH (No condensation
Dimensions		181 x 130 x 59 mm
Weight		Approx. 340 g

Keyence IX-1050 Keyence

9,348.00 kr

Only 5 units left

Specifications

Model			IX-1050
Main unit / expansion unit			Expansion unit
Display	Min. display unit		10 µm^*1
	Display range		±999.99 to ±999 mm (with 4 selectable steps)^*1
Tools	Scan mode		Height, Height difference, Max./Min., Height difference calculation, Thickness calculation, Height detection, Monochromatic detection, Position adjustment (Max. number of settings) Detection: 16 tools, Position adjustment: 1 tool^*2
	Line mode		Height (Ave./Max./Min.) , Height difference (Ave./Max./Min.) , Height difference calculation, Thickness calculation, Position adjustment, Tilt correction (Max. number of settings) Detection: 16 tools, Position adjustment: 1 tool, Alignment adjustment: 1 tool^*2
Other functions	Common		ZERO/offset, Operating threshold adjustment, 2-point calibration, Measurement direction, Position correction NG measurement, Zero/offset recording,Capture mode (HDR) Sensor date/time Information addition, N.O./N.C. switching, I/O monitor, Automatic brightness adjustment, Lighting (ON/OFF) , Total judgment conditions,NPN/PNP switching, Simultaneous main unit/expansion unit input, Light interference prevention, Security
	Scan mode		Measurement range, Measurement position (small/standard/large) , Measurement mode, Measurement noise elimination, Imaging mode (high gain) , Tilt correction (fixed or real-time correction) , Glare removal, Trigger input (internal/external) , Trigger interval, Trigger delay, Trigger error, Monochrome histogram, Fixed reference area, Mask outline, Rotation range
	Line mode		Average count, Laser position adjustment, Timing input, Head tilt correction (fixed only), Ambient light removal for measurement, HOLD function, Alarm setting, Measurement method (Ave./Max./Min.)
Input	Input		Non-voltage input/voltage input is switchable For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Number of inputs		8 (IN1 to IN8)
	Function		IN1: External trigger up/down timing, IN2 to IN8: Enable by assigning optional functions Assignable functions: Program switching, Laser emission stop, Zero/offset (batch) , Reset (error only) , Reset (judgment value only) Reset (judgment value and error)
Output	Output		Open collector output; NPN/PNP switchable, N.O./N.C. switchable For open collector NPN output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit) , residual voltage of 1.5 V or less For open collector PNP output: Maximum rating of 26.4 V, 50 mA (20 mA when linked to an expansion unit) , residual voltage of 2 V or less
	Number of inputs		10 (OUT1 to OUT10)
	Function		Enable by assigning the optional functions Assignable functions: Total judgment result (All OK, Any OK/NG) , run, busy, error, position adjustment result, tilt correction result, Monochromatic detection/Height detection tool result (OK/NG) , Height/height difference/Max./Min./calculation tool result (OK/NG/HIGH/LO) , Alarm
Analog voltage output			Not available
Analog current output
Number of programs			32
Statistical information			Scan mode: Measured value / Degree of similarity (Max., Min., Ave.), Processing time (Latest, Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers) Line mode: Measured value / Degree of similarity (Max., Min., Ave.), Count (Number of OKs / Number of NGs / Number of triggers)^1^3
Detection record	Number of storage	Scan mode	80 images (FTP/SFTP Client function: Enable) 100 images (FTP/SFTP Client function: Disable) ^*4
		Line mode	400 images (FTP/SFTP Client function: Enable) 500 images (FTP/SFTP Client function: Disable) ^*4
Detection history	Save conditions		NG only/All is selectable^*4
FTP/SFTP data transfer (FTP/SFTP client function)	Transfer Destination		FTP/SFTP server
	Transfer format		bmp/jpeg/txt is selectable
	Transfer Condition		4 conditions All / Total status result (OK/NG) / Result for each tool (OK/(NG and ALM)) is selectable
Ethernet	Standard		Not available
	Connector
Interface compatibility			CC-Link / DeviceNet® / EtherNet/IP™ / EtherCAT^Ⓡ / RS-232C / BCD / PROFINET / PROFIBUS / TCP/IP output^*5
Number of connectible units			Main units: 1, Expansion units: 1, Communication units (DL) : 1
Ratings	Power voltage		Supplied from main unit
	Current consumption		Max. 1.9 A or less (With main unit only: 0.8 A or less, With unit expansion: 1.9 A or less) (Excluding output load)^*6
Environmental resistance	Ambient temperature		0 to +50°C 32 to 122°F (No freezing)
	Relative humidity		35 to 85 % RH (No condensation)
Material			Main unit case: PC/Power connector: PA, POM/Analog output connector: PA, POM/I/O connector: PA/ Head connector: Zinc + Ni plating, PA/Ethernet connector: Copper alloy + Ni plating/ Rear heat sink: Aluminum/Main unit rear DIN rail fixing tab: POM/Nameplate: PC
Weight			Approx. 190 g
^1 For displaying on an IX Series control panel or PC software. ^2 Configurable for each program. ^3 When sample hold (edge), peak/bottom/P-P hold (level/edge) is set. ^4 Saves to the inner memory of sensor amplifier. The detection history saved in the sensor amplifier can be copied to PC as a backup by using the PC software or the USB mounted on the control panel for IX series. ^5 When a DL Series device is used. Contact KEYENCE for information on other interfaces. ^6 Includes a DL Series communication unit.

Keyence OP-87836 Keyence

11,616.00 kr

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FR-SH01C Keyence

10,645.00 kr

Only 1 unit left

Specifications

Model		FR-SH01C
Type		Short range Compact chemical model
Measuring range		Up to 1.5 m 4.9'^*1
Display range		Up to 2 m 6.6'^*1
Measurable dielectric constant of medium		2 or higher^*2
Resolution		1 mm 0.04"
Precision		Up to 0.1 m 0.3': ±20 mm 0.79"; 0.1 to 0.3 m 0.3' to 1.0' : ±5 mm 0.20"; 0.3 to 1.5 m 1.0' to 4.9' : ±1 mm 0.04" ^*3
Response time		0.4 s, 1.5 s, 4 s (default value), 10 s
Tank pressure		-0.1 to +0.1 Mpa
Material	Tank interior	Lens: PTFE Internal packing: FKM Joint: PPS
	Housing	PPS PPSU
Connection diameter		G3/4 (20 A)
Output	No. of control outputs	─
	Control output/auxiliary output
	Analog output
External input
Network compatibility
Analog output accuracy	Resolution
	Zero accuracy
	F.S. accuracy
Power supply	Power voltage
	Power consumption
Environmental resistance	Ambient temperature	–10 to +70°C^*4 14°F to 158°F (No freezing)
	Relative humidity	Up to 85% RH (no condensation)
	Temperature of coupling used	–10 to +85°C 14°F to 185°F (no freezing)^*4
	Vibration resistance	10–500 Hz Power spectral density: 0.816 G²; X, Y and Z directions
	Shock resistance	100 m/s² (10 G), 16 ms pulses, 1000 times each for X, Y and Z directions
Enclosure rating		IP67 (IEC60529)
Protection circuit		Protection against reverse power connection, power supply surges, output overcurrent protection, and output surges
Weight		Approx. 140 g 4.94 oz
^1 Guaranteed value in water with the recommended installation. Static water can be measured up to the edge of the lens. An undetectable area on the short-range side is created due to the environment and measurement medium. The maximum measuring distance is also shortened. ^2 Measurement may not be possible depending on the shape and environment of the target. ^3 This is the guaranteed value from verification performed at KEYENCE inspection facilities. Measurement errors may occur depending on the customer’s environment. ^4 The FR-S01 and FR-LM20L/LP20L can be used up to an ambient temperature setpoint of 10°C 50°F by selecting “Off when not in Operation” under “Screen Brightness.”

Keyence IV-G15 Keyence

5,211.00 kr

Only 9 units left

Specifications

Model		IV-G15
Type		Expansion unit
Tools	Type	Shape Detection, Color Area^1, Area^2, position adjustment
	Number	Detection tools: 16 tools, position adjustment tool: 1 tool^*3
Switch settings (programs)		32 programs
Image history	Numbers	When using a color type head: 100 images^4, when using a monochrome type head: 300 images^5^*6
	Condition	NG only/All is selectable^*6
Analysis information		OFF/Statistics/Histograms is switchable Statistics: Processing time (latest value, MAX, MIN, AVE), number of OKs, number of NGs, trigger numbers, trigger errors, judgment results list by tools Histograms: Histogram, matching degree (latest value, MAX, MIN, AVE), numbers of OKs, numbers of NGs^*7
Other functions		HDR, HighGain, Color filters^1, Digital zoom (2x, 4x)^8, Brightness correction, Tilt correction, White balance^*1, Mask outline, Mask area, Test run, ToolAutoTune, Input monitor, Output test, Security settings, Simulator, Mutual interference prevention, Total judgment result output, Direct connection (2 units or more), Failing sensor list, Failure hold
Indicators		PWR/ERR, OUT, TRIG, STATUS, LINK/ACT
Input	Type	Non-voltage input/voltage input is switchable For non-voltage input: ON voltage 2 V or lower, OFF current 0.1 mA or lower, ON current 2 mA (short circuit) For voltage input: Maximum input rating 26.4 V, ON voltage 18 V or higher, OFF current 0.2 mA or lower, ON current 2 mA (for 24 V)
	Inputs	6 inputs (IN1 to IN6)
	Function	IN1: External trigger, IN2 to IN6: Enable by assigning the optional functions Assignable functions: Program switching, Clear error, External master image registration, Main unit/expansion unit simultaneous input
Output	Type	Open collector output NPN/PNP is switchable, N.O./N.C. is switchable For open collector NPN output: Maximum rating 26.4 V 50 mA (20 mA when linked to an expansion unit [IV-G15]), remaining voltage 1.5 V or lower For open collector PNP output: Maximum rating 26.4 V 50 mA (20 mA when linked to an expansion unit [IV-G15]), remaining voltage 2 V or lower
	Outputs	8 outputs (OUT1 to OUT8)
	Function	Enable by assigning the optional functions Assignable functions: Total judgment result, RUN, BUSY, Error, Position adjustment result, Judgment result of each tool, Result of the logical operation of each tool, Main unit/expansion unit logical output
Ethernet	Standard	100BASE-TX/10BASE-T^*9
	Connector	RJ-45 8pin connector^*9
Network function		FTP client, EtherNet/IP™, PROFINET
Rating	Power voltage	Supplied from main unit
	Current consumption	0.8 A or less. 1.5 A or less when also using an expansion unit (IV-G15). (The output load is excluded.)
Environmental resistance	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)^*10
	Relative humidity	35 to 85 % RH (No condensation)
Material		Main unit case: Polycarbonate
Weight		Approx. 150 g
^1 Color type only ^2 Monochrome type only ^3 Tools can be installed by programs. ^4 When using the FTP client function: 70 pictures ^5 When using the FTP client function: 210 pictures ^6 Saves to the sensor amplifier's internal memory. The images saved to the sensor amplifier can be backed up to the USB memory device inserted into the intelligent monitor (IV-M30) or to the PC by the software for the IV/IV-G Series (IV-H1). ^7 This can be displayed on the intelligent monitor (IV-M30) or by software for IV (IV-H1). ^8 Possible with both the color type and monochrome type ^9 This is for connection with the intelligent monitor (IV-M30) or software for the IV/IV-G Series (IV-H1). ^10 When attaching the sensor amplifier to a DIN rail, attach the sensor amplifier to a metal plate.

Keyence OP-87354 Keyence

1,828.00 kr

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FI-T15 Keyence

4,144.00 kr

Only 1 unit left

Specifications

Model			FI-T15
Supported pipe diameter			3/8", 1/2" (10A, 15A) ø14–22 ø0.55"–0.87"
Supported pipe materials			Metal piping
Supported temperature range			−20 to +180°C –4 to +356°F^*1
Display method			Organic EL, status indicator light
Display resolution			0.1°C 32.18°F
Response time			5 s (50% response), 15 s (90% response)^*2
Display amplifier averaging time			0.1 s / 10.0 s / 20.0 s / 30.0 s / 60.0 s / 120.0 s / 300.0 s
Measurement accuracy			±0.5°C ±0.9°F (pipe temperature −20 to +80°C –4 to 176°F) (ambient temperature of 25°C 77°F)^2^3 ±1.0°C ±1.8°F (pipe temperature 80–180°C 176–356°F) (ambient temperature of 25°C 77°F)^2^3
Hysteresis			Variable
Measurement principle			Pt100 4-wire type
Power I/O connector			M8 4-pin connector
Power supply	Current consumption		20 mA or less (excluding load current)^*4
When used standalone	I/O (switchable)	Output (Ch1/Ch2)	Control output: switching NPN/PNP setting Open collector output: 30 VDC or less, maximum 100 mA/ch or less, residual voltage 2.5 V or less^*5
		Analog output (Ch2)	4–20 mA / 0–20 mA (switchable), load resistance 260 Ω or less^*5
	Power voltage		20–30 VDC, ripple (P-P) 10% included; Class2/LPS^*5
	Protection circuit		Protection against reverse power connection, power supply surges, output short circuits, and output surges^*5
	Network compatibility		IO-Link^6^5
Environmental resistance	Enclosure rating		IP65/IP67 (IEC60529)
	Ambient temperature		–10 to +60°C -14 to +140°F (no freezing)
	Relative humidity		35–85% RH (no condensation)
	Vibration resistance		10–500 Hz; power spectral density: 0.816 G²/Hz; X, Y and Z directions
	Shock resistance		100 m/s² (approx. 10 G), 16 ms pulses, 1000 times each for X, Y and Z directions
Material	Display amplifier		PBT / PAR / POM / SUS303
	Sensor head		Head: PPS / SUS303 / Sn; Pipe clamp unit: SUS304; Cable: fluororesin
	Display amplifier mounting bracket		SUS304
Weight			Approx. 80 g 2.82 oz
^1 When pipe temperature is 100°C 212°F or more, the display amplifier cannot be mounted on the pipe clamp unit. Install the amplifier so it is insulated from the heat from the pipe. ^2 This is the guaranteed value from verification performed at KEYENCE inspection facilities. Measurement error may occur depending on the type and condition of the customer’s pipes and fluid, the ambient temperature and other factors. ^3 This is the value for a constant 25°C 77°F environment, taking into account absolute error and repeatability. ^4 During standalone use, 220 mA or less including load. ^5 When connecting to a FD-H Series/FI-1000 model, please follow the specifications of the display unit. ^6 Supports IO-Link specification v.1.1/COM2 (38.4 kbps). Setting files can be downloaded from the KEYENCE website (www.keyence.com). IO-Link is a trademark or registered trademark of PROFIBUS Nutzerorganisation e.V. (PNO).

Keyence SV3-B020AS Keyence

0.00 kr

Sold Out

Specifications

Model				SV3-B020AS ^*1
General specifications	Applicable servo amplifier			SV3-020L2
	Rated output			200 W
	Rated torque			0.637 N·m ^*2
	Instant maximum torque			2.23 N·m
	Rated current			1.6 Arms
	Instant maximum current			5.8 Arms
	Rated rotation speed			3,000 min^-1
	High rotation speed			7,000 min^-1
	Torque constant			0.444 N·m/Arms
	Rotor moment of inertia			0.327 ×10^-4 kg·m²
	Rated power rating			12.4 kW/s
	Rated angle acceleration			19,400 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		26 bit
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or higher)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20% to 80% RH (No condensation)
		Operating atmosphere		Indoors (No corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2,000 m 6,561.7' or less (reduced ratings at 1,000 m 3,280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8 ft/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1,607.6 ft/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: Class A, CE: Class B
	Min. insulation resistance			500 VDC 10 MΩ or more with insulation resistance meter
	Isolation voltage tolerance			1,500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part 15 B, ICES-003. Class A
	Allowable load inertia moment			15×^*3
	Approx. weight			1.4 kg 3.09 lb
Electromagnetic brake specifications	Capacity			6 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.25 A
	Holding torque			0.637 N·m
	Release time			60 ms
	Operating time			100 ms
^1 The open and operation times of the electromagnetic brake depend on the discharge circuit. ^2 50 W to 750 W rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W/100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with an ambient temperature of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^*3 This is the value at 6,000 min-1. At 7,000 min-1, 200 W becomes 10×, 400 W becomes 5×, and 750 W becomes 8×.

Keyence FU-R6F Keyence

0.00 kr

Sold Out

Specifications

Model		FU-R6F^*1
Type		Threaded and Hex-Shaped Active Receiver Fibers
Size		M6
Fibre unit length		2 m6.6'Free-cut
Fibre unit diameter		ø 2.2ø 0.09" x 2
Shape		Threaded
Minimum bend radius		R25 mmR0.98"
Environmental resistance	Ambient temperature	−40 to +60 ˚C -40 to +140 °F
Weight		Approx. 21 g
^*1 For details on the detecting distance, see the fiber amplifier catalog.

Keyence CV-X202F Keyence

37,270.00 kr

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence CA-DQR10M Keyence

10,385.00 kr

Only 1 unit left

Specifications

Model				CA-DQR10M
Type				Square Lights (Multi-Angle)
LED color				red
Power consumption				11.7 W
Weight				Approx 250 g

Keyence OP-89156 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence GV-H100L Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence ER-M05NC Keyence

0.00 kr

Sold Out

Specifications

Model		ER-M05NC
Type		Compact all-metal shielded type Screw type M5 Connector (M8 3-pin) NPN output
Power supply cable length		― ^*1
No. of control outputs		1
Output mode		N.O.
Button		None
Button	Function	―
Detecting distance		1.5 mm 0.06" ±10% ^*2
Response frequency		170 Hz ^3 ^4
Hysteresis distance		15% or less of detecting distance
Detectable object		Magnetic metal, Non-magnetic metal ^*5
Standard detectable object (Iron, t = 1 mm 0.04")		5 × 5 mm 0.20" × 0.20"
Temperature characteristics		±10% or less of detecting distance at +25°C +77°F (0 to +55°C 32°F to 131°F) ±15% or less of detecting distance at +25°C +77°F (-25 to 0°C -13°F to +32°F, +55 to +70°C 131°F to +158°F)
Control output		Open-collector, 30 VDC or less, Max. 50 mA
Control output	Residual voltage	NPN output: 0.9 V or less (Output current: 10 mA or less) / 1.4 V or less (Output current: 10 to 50 mA) ^*6
Power supply	Power voltage	16 to 30 VDC (including 10% or less ripple (P-P)), Class 2
	Power consumption (excluding load current)	960 mW or less (40 mA or less at 24 V, 60 mA or less at 16 V)
Protection circuit		Protection against reverse power connections, output short-circuits, and reverse output connections
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient temperature	-25 to +70°C -13°F to +158°F (no freezing)
	Relative humidity	Up to 95% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	500 m/s² 1640.4 ft/s² (50 G), 10 times in each of the X, Y, and Z directions
Material	Head	SUS316L Epoxy resin
	Amplifier	Header-to-amplifier cable: TPU, Case: PBT/TPU [Connector] Indicator: LCP, Connector metal: SUS303, Connector: LCP [Cable] Indicator: TPU, Power cable: PVC
	Accessories	Nut: SUS303
Accessories		Nut × 2
Weight		Approx. 25 g 0.88 oz
^1 Ensure the power cable is no longer than 30 m 98.4' for connector types and no longer than 20 m 65.6' with IO-Link connections. ^2 The distance at which a standard detectable object can be detected when the unit is mounted without being affected by surrounding metal. ^3 Value when a standard detectable object is used, the distance between detectable objects is twice the standard detectable object, and the distance to the detectable object is 1/2 the detecting distance. ^4 The response frequency varies depending on the operating temperature. The response frequency at temperatures of +55°C +131°F or higher is 50% of that at +25°C +77°F. ^5 Detecting distance varies according to the material and size. See the characteristic diagrams for details. ^6 Residual voltage is for when a 2 m 6.6' cable is used.

Keyence EV-118UC Keyence

0.00 kr

Sold Out

Specifications

Model		EV-118UC
Type		DC , Non-shielded
Shape		M18
Detecting distance		15 mm 0.59" ±10%
Detectable object		Ferrous metals (see Characteristics for nonferrous metals)
Standard target (iron, t=1 mm 0.04")		50 x 50 mm 1.97"
Hysteresis		20% max. of detecting distance, within -10 to +70°C 14 to 158°F
Response frequency		350 Hz
Operation mode		N.C.
Temperature characteristics		±10% max. of detecting distance, within -10 to +70°C 14 to 158°F
Control output (switching capacity)		5 to 200 mA
Protection circuit		Reversed polarity, short-circuit, surge voltage
Rating	Power voltage	12 to 24 VDC, Ripple (P-P) 20 % or less
	Current consumption (leakage current)	Current consumption (leakage current): 1.0 mA max., Residual voltage: 3.6 V max. (with 2-m 6.6' cable)
	Residual voltage	Residual voltage: 3.6 V max. (with 2-m 6.6' cable)
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +80 °C -13 to 176 °F (No freezing)
	Relative humidity	35 to 95 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	1,000 m/s², 3 times in each of the X, Y, and Z directions
Case material		Nickel-plated brass
Accessories		Nut × 2, toothed washer × 1, instruction manual
Weight		Approx. 140 g

Keyence CA-LH50 Keyence

2,568.00 kr

Only 5 units left

Specifications

Model				CA-LH50
Focal point				50 mm 1.97"
F-stop range (aperture)				F2.8 to F22
Minimum WD				0.2 m 0.7'
Mount				C-mount
Filter size				27.0 mm 1.06" P0.5
Compatible image sensor size				2/3"
TV distortion				-0.03 % (-0.01 %)^*1
Resolving power				100 cycles/mm at center, 80 cycles/mm on periphery
Ambient temperature/humidity range				0 to +50°C 32 to 122°F, 80% RH or less (No condensation)
Weight				Approx. 92 g
^*1 Indicates specification for compatible image sensor size. Value in parenthesis applies to 1/3" image sensor size.

Keyence EM-080 Keyence

5,176.00 kr

Only 2 units left

Specifications

Model		EM-080
Type		Shielded
Shape		8 mm 0.31" dia Cylindrical.
Detecting distance		2.0 mm 0.08" ±10%
Detectable object		Ferrous metals (see Characteristics for non-ferrous metals)
Standard target (iron, t=1 mm 0.04")		10 x 10 mm 0.39" x 0.39"
Hysteresis		10% max. of detecting distance
Response frequency		1.2 kHz
Operation mode		N.O.
Temperature characteristics		±10% max. of detecting distance at +23°C 73.4°F, within -10 to +70°C 14 to 158°F
Display indicator		Red LED
Output		NPN
Control output		NPN: 200 mA (40 V) max., Residual voltage: 1 V max.
Housing		Stainless steel
Rating	Power voltage	10.8 to 30 VDC, Ripple (P-P) 10 % or less^*1
	Current consumption	12 mA or less
Environmental resistance	Enclosure rating	IP67
	Ambient temperature	-25 to +80 °C -13 to 176 °F (No freezing)
	Relative humidity	35 to 95 % RH (No condensation)
Weight		Approx. 42 g (including nuts and 2-m 6.6' cable)
^*1 Make sure that the power voltage stays within 10.8 V to 30 V even if it is affected by ripple effects.

Keyence AP-32ZP Keyence

0.00 kr

Sold Out

Specifications

Model		AP-32ZP
Type		Positive-pressure Type, PNP
Rated pressure		0 to 100.0 kPa
Fluid type		Air or non-corrosive gases
Type of pressure		Gauge pressure, air or non-corrosive gases
Display		3 1/2-digit, 2-color, 7-segment LED (Character height: 11 mm 0.43"), Display cycle: 5 times/s
Display resolution		0.1 kPa (0.001 bar)
Detectable pressure range		-15 to +110 % of F.S.
Hysteresis		Variable (when hysteresis mode is selected), 0.5 % of F.S. in standard mode
Response time (Chattering prevention function)		2.5/5/100/500 ms (selectable)
I/O	Zero-shift input	Input time: 20 ms or more
	Control output	PNP open-collector 100 mA max. (30 V max.), Residual voltage: 1 V max. 2-output (N.O./N.C.selectable)
Rating	Power voltage	12 to 24 VDC ±10 %
	Current consumption	50 mA (at 24 V) or less, 90 mA (at 12 V) or less
Environmental resistance	Pressure resistance	5.0 bar (500 kPa)
	Ambient temperature	0 to +50 °C 32 to 122 °F (No freezing)
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
Material		Front housing: Polyamide, Front panel sheet: PET, Rear housing: Polysulfone,Pressure port: Die-cast zinc, Cable: Oil-proof cabtyre cable
Accessories		Mounting bracket A, mounting bracket B, hexagon socket head cap plug
Weight		Approx. 120 g

Keyence FS-MC8P Keyence

3,146.00 kr

In stock, 54 units

Specifications

Model		FS-MC8P
Output		PNP
Response time		Depends on the response time settings of the connected expansion units
External input		Input time of the connected expansion units +11 ms
Number of inputs and outputs		Separate control outputs: 8, common output: 1, common input: 1
Unit expansion		Up to 8 expansion units can be connected. (However, each dual output type will be treated as 2 expansion units.) Allowable passing current: 1200 mA or less
Indicators		STATUS indicator (green and red two-color display) MEMORY indicator (orange) LOCK indicator (orange)
Separate control output, common output		PNP open-collector, 30 V or less, 20 mA or less per output, residual voltage: 1.6 V or less
Protection circuit		Protection against reverse power connection, reverse output connection, output overcurrent, and output surge
Power supply	Power voltage	10 to 30 VDC (including 10 % ripple (P-P) or less) , class 2 or LPS^*1
	Power consumption	690 mW or less (when used as a solitary unit) (26 mA or less at 24 V/38 mA or less at 12 V [excluding the load current] )^*2
Environmental resistance	Ambient temperature	-20 °C -4 °F to +55 °C +131 °F (no freezing)
	Vibration resistance	10 to 55 Hz; double amplitude 1.5 mm 0.06"; 2 hours each for X, Y, and Z axes
	Shock resistance	500 m/s²; 3 times each for X, Y, and Z axes
Case material		Main unit and cover: polycarbonate
Weight		Approx. 110 g
^1 Match the rated power supply voltage of the expansion units to be connected to the system. ^2 The power consumption including the load when the maximum number of units are connected is 38 W max.

Keyence OP-88886 Keyence

0.00 kr

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence KV-16DTP Keyence

8,573.00 kr

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence FR-LEXB44 Keyence

0.00 kr

Sold Out

Specifications

Model				FR-LEXB44
Type				Zener barrier with explosion-proof box
Input/Output				2-wire system
Explosion-Proof Specifications				AEx db [ia Ga] IIB T4 Gb AEx tb [ia Da] IIIC T135°C Db