keyence

Showing 6241 - 6264 of 6950 products

€0,00

Sold Out

Specifications

Model				SV-D5D
Type				Electromagnetic brake cable
Length				5 m 16.4'
Note				Applicable servo amplifier capacity: 1 k to 5 kW

Keyence SV-E10A Keyence

€283,95

Only 2 units left

Specifications

Model				SV-E10A
Type				Encoder cable, Standard
Length				10 m 32.8'
Note				for 1 k to 5 kW motor

Keyence SV-E20A Keyence

€0,00

Sold Out

Specifications

Model				SV-E20A
Type				Encoder cable, Standard
Length				20 m 65.6'
Note				for 1 k to 5 kW motor

Keyence SV-E3A Keyence

€0,00

Sold Out

Specifications

Model				SV-E3A
Type				Encoder cable, Standard
Length				3 m 9.8'
Note				for 1 k to 5 kW motor

Keyence SV-E5A Keyence

€0,00

Sold Out

Specifications

Model				SV-E5A
Type				Encoder cable, Standard
Length				5 m 16.4'
Note				for 1 k to 5 kW motor

Keyence SV-FC1 Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SV-LN1 Keyence

€0,00

Sold Out

Specifications

Model				SV-LN1
Type				Linear encoder connection cable
Length				1 m 3.3'

Keyence SV-M010CK Keyence

€3.673,95

Only 2 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SV-ST1 Keyence

€0,00

Sold Out

Specifications

Model				SV-ST1
Type				Safety function cable
Length				1 m 3.3'

Keyence SV-ST3 Keyence

€301,95

Only 2 units left

Specifications

Model				SV-ST3
Type				Safety function cable
Length				3 m 9.8'

Keyence SV-T1 Keyence

€0,00

Sold Out

Specifications

Model				SV-T1
Type				Terminal kit
Note				For 2/3 kW

Keyence SV2-005L2 Keyence

€984,95

Only 4 units left

Specifications

Model				SV2-005L2
General specifications	Capacity			50 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single phase) 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 0.8 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single phase 200 V
	Max. applicable motor capacity			50 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 0.2 kVA, Single phase 200 V: 0.2 kVA
	Output current	Continuous		0.66 Arms
		Max.		2.1 Arms
	Main circuit power loss			5.1 W
	Regenerative resistor power loss			—
	Control circuit power loss			17 W
	Total power loss			22.1 W
	Rated input current	Main circuit		Three-phase 200 V: 0.4 Arms, Single phase 200 V: 0.8 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-010L2 Keyence

€388,95

Only 1 unit left

Specifications

Model				SV2-010L2
General specifications	Capacity			100 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single phase) 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 0.8 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single phase 200 V
	Max. applicable motor capacity			100 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 0.3 kVA, Single phase 200 V: 0.3 kVA
	Output current	Continuous		0.91 Arms
		Max.		3.2 Arms
	Main circuit power loss			7.3 W
	Regenerative resistor power loss			—
	Control circuit power loss			17 W
	Total power loss			24.3 W
	Rated input current	Main circuit		Three-phase 200 V: 0.8 Arms, Single phase 200 V: 1.6 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-020L2 Keyence

€674,95

Only 3 units left

Specifications

Model				SV2-020L2
General specifications	Capacity			200 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single phase) 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 0.8 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single phase 200 V
	Max. applicable motor capacity			200 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 0.5 kVA, Single phase 200 V: 0.6 kVA
	Output current	Continuous		1.6 Arms
		Max.		5.9 Arms
	Main circuit power loss			13.5 W
	Regenerative resistor power loss			—
	Control circuit power loss			17 W
	Total power loss			30.5 W
	Rated input current	Main circuit		Three-phase 200 V: 1.3 Arms, Single phase 200 V: 2.4 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-040L2 Keyence

€1.156,95

Only 5 units left

Specifications

Model				SV2-040L2
General specifications	Capacity			400 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single phase) 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 1.0 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single phase 200 V
	Max. applicable motor capacity			400 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 1 kVA, Single phase 200 V: 1.2 kVA
	Output current	Continuous		2.8 Arms
		Max.		9.3 Arms
	Main circuit power loss			24 W
	Regenerative resistor power loss			—
	Control circuit power loss			17 W
	Total power loss			41 W
	Rated input current	Main circuit		Three-phase 200 V: 2.5 Arms, Single phase 200 V: 5.0 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-075L2 Keyence

€674,95

Only 2 units left

Specifications

Model				SV2-075L2
General specifications	Capacity			750 W
	Input power supply	Voltage/frequency	Main circuit	3-phase (or single phase) 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 1.6 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V/Single phase 200 V
	Max. applicable motor capacity			750 W
	Power supply capacity for 1 amplifier			Three-phase 200 V: 1.6 kVA, Single phase 200 V: 1.9 kVA
	Output current	Continuous		5.5 Arms
		Max.		16.9 Arms
	Main circuit power loss			43.8 W
	Regenerative resistor power loss			8 W
	Control circuit power loss			17 W
	Total power loss			68.8 W
	Rated input current	Main circuit		Three-phase 200 V: 4.1 Arms, Single phase 200 V: 8.7 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-100L2 Keyence

€1.791,95

Only 2 units left

Specifications

Model				SV2-100L2
General specifications	Capacity			1.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 1.6 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V
	Max. applicable motor capacity			1.0 kW
	Power supply capacity for 1 amplifier			Three-phase 200 V: 2.3 kVA
	Output current	Continuous		7.6 Arms
		Max.		17 Arms
	Main circuit power loss			53.6 W
	Regenerative resistor power loss			8 W
	Control circuit power loss			17 W
	Total power loss			78.6 W
	Rated input current	Main circuit		Three-phase 200 V: 5.7 Arms
		Control circuit		0.2 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-150L2 Keyence

€798,95

Only 1 unit left

Specifications

Model				SV2-150L2
General specifications	Capacity			1.5 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP20
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 2.2 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V
	Max. applicable motor capacity			1.5 kW
	Power supply capacity for 1 amplifier			Three-phase 200 V: 3.2 kVA
	Output current	Continuous		11.6 Arms
		Max.		28 Arms
	Main circuit power loss			65.8 W
	Regenerative resistor power loss			10 W
	Control circuit power loss			22 W
	Total power loss			97.8 W
	Rated input current	Main circuit		Three-phase 200 V: 7.3 Arms
		Control circuit		0.25 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-200L2 Keyence

€1.508,95

Only 3 units left

Specifications

Model				SV2-200L2
General specifications	Capacity			2.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP10
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 2.7 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V
	Max. applicable motor capacity			2.0 kW
	Power supply capacity for 1 amplifier			Three-phase 200 V: 4 kVA
	Output current	Continuous		18.5 Arms
		Max.		42 Arms
	Main circuit power loss			111.9 W
	Regenerative resistor power loss			16 W
	Control circuit power loss			22 W
	Total power loss			149.9 W
	Rated input current	Main circuit		Three-phase 200 V: 10 Arms
		Control circuit		0.25 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-300L2 Keyence

€1.805,95

Only 2 units left

Specifications

Model				SV2-300L2
General specifications	Capacity			3.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP10
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 2.7 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V
	Max. applicable motor capacity			3.0 kW
	Power supply capacity for 1 amplifier			Three-phase 200 V: 5.9 kVA
	Output current	Continuous		19.6 Arms
		Max.		56 Arms
	Main circuit power loss			113.8 W
	Regenerative resistor power loss			16 W
	Control circuit power loss			22 W
	Total power loss			151.8 W
	Rated input current	Main circuit		Three-phase 200 V: 15 Arms
		Control circuit		0.25 Arms
	Rush current	Main circuit		34 A
		Control circuit
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-500L2 Keyence

€685,95

Only 1 unit left

Specifications

Model				SV2-500L2
General specifications	Capacity			5.0 kW
	Input power supply	Voltage/frequency	Main circuit	3-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
			Control circuit	Single-phase 200 to 240 VAC +10 to -15%, 50/60 Hz 270 to 324 VDC ^*1
		Allowable frequency fluctuation	Main circuit/control circuit	No more than ±5%
		Overvoltage category		III
	Control mode			Three-phase full-wave rectification, IGBT, PWM control, sine-wave current driving method
	Feedback			22-bit serial encoder (absolute) communication, fully closed control serial communication, analog feedback
	Operating environment	Operating atmosphere	Enclosure rating	IP10
			Pollution degree	Pollution degree: 2 (in an IP54 or higher control panel) However, usage under the following requirements required: • No corrosive gas or flammable gas present • No exposure to water, oil, or chemicals • No dust present
		Operating ambient temperature		-5 to +60°C 23 to 140°F (no freezing; reduced ratings at +55°C 131°F or more)
		Storage ambient temperature		-20 to +85°C -4 to +185°F (no freezing)
		Operating/storage ambient temperature		95% RH or less (no condensation)
		Altitude		2000 m 6561.7' or less above sea level (usable at reduced ratings at 1000 m 3280.8' or more)
		Vibration resistance		4.9 m/s² 16.1'/s² (JIS C60068-2-6 compliant)
		Impact resistance		19.6 m/s² 64.3'/s² ( JIS C60068-2-27 compliant)
		Other		No static electricity noise, strong electric fields, magnetic fields, or radiation present
	Min. insulation resistance			500 VDC, 1 MΩ or more with insulation resistance tester
	Applied standard	UL/CSA standards		UL61800-5-1, CSA22.2 No.274
		CE marking	Low-voltage directive	EN61800-5-1, EN50178
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Structure	Type		Attached to base mount
	Safety function			STO function (STO/EN61800-5-2)
	Safety function	Safety parameters		SIL3/EN61508, SIL CL 3/EN62061, PLe (Category3) / EN ISO13849-1: 2008
		Response time		8 ms (max.)
		Input		STO1, STO2: Base block signal for power module Internal impedance: 4.7 kΩ Operable voltage range: +24 V ±20% Max. delay time: 8 ms (Time from turning STO1, STO2 off until motor current cutoff)
		Output		EDM: Built-in safety circuit status monitoring (fixed output) Max. allowable voltage: 30 VDC Max. allowable current: 50 mA DC Max. voltage drop at ON: 1.5 V Max. delay time: 8 ms (Time from changing STO1, STO2 until EDM change)
		Applied standard		EN61800-5-2, EN ISO13849-1: 2008, EN61508, EN62061, EN60204-1, EN61326-3-1
	Protection function			Overcurrent, overvoltage, undervoltage, overload, regenerative abnormalities, etc.
	Insulation withstand voltage			1500 VAC or more (between primary side and ground) 3000 VAC or more (between primary side and secondary side) 350 VAC: Between secondary circuit and ground
	Weight			Approx. 4.4 kg
Power supply/current capacity and power loss	Main circuit power supply			Three-phase 200 V
	Max. applicable motor capacity			5.0 kW
	Power supply capacity for 1 amplifier			Three-phase 200 V: 7.5 kVA
	Output current	Continuous		32.9 Arms
		Max.		84 Arms
	Main circuit power loss			263.7 W
	Regenerative resistor power loss			36 W
	Control circuit power loss			27 W
	Total power loss			326.7 W
	Rated input current	Main circuit		Three-phase 200 V: 25 Arms
		Control circuit		0.3 Arms
	Rush current	Main circuit		68 A
		Control circuit		34 A
Performance specifications	Performance	Speed control range		1:5000 (load torque ≤ rated torque conditions)
		Speed fluctuation rate	At load fluctuation	±0.01% or less with load fluctuations of 0 to 100% (at rated rotation speed)
			At main circuit voltage change	0% with ±10% of rated voltage (at rated rotation speed)
			At ambient temperature change	±0.1% or less with ambient temperatures of 0 to +50°C 32 to 122°F (at rated rotation speed)
		Torque control accuracy (reproducibility)		±1%
		Speed frequency response frequency		2.6 kHz
	Dynamic brake			Operated at main circuit power supply OFF, servo alarm, limit switch detection (LSP/LSN), forced stop detection (FSTOP)
	Regenerative resistor			Built-in regenerative resistor: 50 W to 400 W ... not installed 750 W to 5.0 kW ... installed External regenerative resistor: OP-84399 (50 W to 1.0 kW) OP-87073 (1.5 kW ^*2)
	Display Function	Panel function		7-segment LED Rotary switch ×2 (16 ch) Slide switch ×1 (4 ch)
		Status display LED		CHARGE: For notification of main circuit power supply input (orange) POWER: For notification of control circuit power supply input (green) CONNECT: For notification of connection (green) LINK1, LINK2: For notification of MECHATROLINK communication (green)
	Auxiliary function			Gain control, alarm history, Z-phase search, etc.
I/O specifications	Sequence input signal	Number of inputs		7 (3 high-speed input, 4 general input)
		Max. input voltage		28.8 VDC
		Rated input voltage		24 VDC
		Min. ON voltage		19 VDC
		Min. OFF current/voltage		High-speed input: 0.6 mA, general input: 0.3 mA
		Common point mode		7 points/1 common point (1 terminal) (bidirectional)
		Input time constant		250 μs, 500 μs, 1 ms, 2.5 ms, 5 ms, 10 ms
		Input current		High-speed input: 4.5 mA, general input: 3.7 mA
		Input impedance		Approx. 4.7 kΩ
		Assignable input signals		Full signal assignment, logic-settable forced stop (FSTOP), external latch signals 1 to 3 (EXT1, EXT2, EXT3), origin return deceleration switch (DEC), forward limit switch (LSP), reverse limit switch (LSN), forward torque limit selection (PTL), reverse torque limit selection (NTL)
	Sequence output signal	Number of outputs		4
		Output mode		Transistor NPN output
		Rated load		30 VDC / 50 mA
		Leakage current when OFF		0.1 mA
		Residual voltage when ON		1.5 VDC or less
		Common point mode		Independent common
		Assignable output signals		Individual signal assignment excluding ALARM signal, logic-settable alarm (ALARM), in position (INPOS), speed matching (VCMP), zero speed detection (ZSP), operation preparation complete (RDY), torque limiting (TLM), speed limiting (VLM), electromagnetic brake timing (BRAKE), warning (WARN), Positioning proximity (NEAR)
	Analog Feedback Input signal monitor	Max. input voltage		±12 V
		Accuracy		±1% of F.S.
		Resolution		±10 bits
		Input impedance		30 kΩ
	Encoder division pulse output signal	Output mode		Phase A (A+/A−), phase B(B+/B−), phase Z (Z+/Z−): Differential line-driver output
		Line driver		SN75ALS174 (T.I.) or equivalent
		Output frequency		1.6 Mbps (with 2-phase, 4 times multiplication, 6.4 MHz or equivalent) ^*3
	Analog monitor output	No. of channels		2 ch
		Output range		±10 V (linearity valid range ±8 V)
		Resolution		16 bits
		Conversion precision		±20 mV (typ.)
		Max. allowable load current		±10 mA
		Conversion speed		1.2 ms (typ.)
Communication specifications	MECHATROLINK-III communication	Communication protocol		MECHATROLINK-III
		Station address		03H to EFH (Max. number of connectable slaves: 62)
		Transmission speed		100 Mbps
		Transmission frequency		125 μs, 250 μs, 500 μs, 750 μs, 1 to 4 ms (in multiples of 0.5 ms)
		Communication cycle		Support for values starting at transmission frequency × 1
		Number of transmitted bytes		32 bytes/station, 48 bytes/station (selectable with slide switch)
		Transmission media/cable		Category 5e-compliant, STP cross cable
		Operating specifications		Position control / speed control / torque control
		Command input		MECHATROLINK-III command (sequence, motion, monitor, adjustment, etc.)
		Max. transmission distance		50 m 164.0' ^*4
	USB communication	Connected device		PC
		Communication standard		USB 2.0-compliant
		Function		Status display, parameter setting, tuning, etc.
^1 When using a DC power supply input, set “AC/DC power supply” to “DC”. ^2 Use of 2 kW, 3 kW, and 5 kW servo amplifiers is possible depending on the operating conditions. ^3 The division ratio can be set arbitrarily with a parameter. ^*4 For instances with 30 m 98.4' or more, use ferrite cores (OP-84409) with 2 turn-winding.

Keyence SV2-B005AK Keyence

€0,00

Sold Out

Specifications

Model				SV2-B005AK
General specifications	Applicable servo amplifier			SV2-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*1
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3000min^-1
	High rotation speed			6000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0475 ×10^-4kg·m²
	Rated power rating			6.40 kW/s
	Rated angle acceleration			40200 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		22 bits
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole area)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or more)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20 to 80% RH (no condensation)
		Operating atmosphere		Indoors (no corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2000 m 6561.7' or less (reduced ratings at 1000 m 3280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8'/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1607.6'/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: phase A, CE: phase B
	Min. insulation resistance			500 VDC, 10 MΩ or more with insulation resistance tester
	Isolation voltage tolerance			1500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Allowable load inertia moment			35 ×
	Approx. weight			0.6 kg
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.159 N·m
	Release time			60 ms ^*2
	Operating time			100 ms ^*2
^1 50 W to 750 W rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W / 100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^2 The release time and operation time of the electromagnetic brake vary depending on the discharge circuit.

Keyence SV2-B005AS Keyence

€981,95

Only 2 units left

Specifications

Model				SV2-B005AS
General specifications	Applicable servo amplifier			SV2-005L2
	Rated output			50 W
	Rated torque			0.159 N·m ^*1
	Instant maximum torque			0.557 N·m
	Rated current			0.55 Arms
	Instant maximum current			2.0 Arms
	Rated rotation speed			3000min^-1
	High rotation speed			6000 min^-1
	Torque constant			0.316 N·m/Arms
	Rotor moment of inertia			0.0475 ×10^-4kg·m²
	Rated power rating			6.40 kW/s
	Rated angle acceleration			40200 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		22 bits
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole area)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or more)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20 to 80% RH (no condensation)
		Operating atmosphere		Indoors (no corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2000 m 6561.7' or less (reduced ratings at 1000 m 3280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8'/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1607.6'/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: phase A, CE: phase B
	Min. insulation resistance			500 VDC, 10 MΩ or more with insulation resistance tester
	Isolation voltage tolerance			1500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Allowable load inertia moment			35 ×
	Approx. weight			0.6 kg
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.159 N·m
	Release time			60 ms ^*2
	Operating time			100 ms ^*2
^1 50 W to 750 W rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W / 100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^2 The release time and operation time of the electromagnetic brake vary depending on the discharge circuit.

Keyence SV2-B010AK Keyence

€0,00

Sold Out

Specifications

Model				SV2-B010AK
General specifications	Applicable servo amplifier			SV2-010L2
	Rated output			100 W
	Rated torque			0.318 N·m ^*1
	Instant maximum torque			1.11 N·m
	Rated current			0.85 Arms
	Instant maximum current			3.1 Arms
	Rated rotation speed			3000min^-1
	High rotation speed			6000 min^-1
	Torque constant			0.413 N·m/Arms
	Rotor moment of inertia			0.0739 ×10^-4kg·m²
	Rated power rating			15.3 kW/s
	Rated angle acceleration			48200 rad/s²
	Excitation method			Permanent magnet
	Position/speed detection encoder	Resolution		22 bits
		Type		Absolute (ABS) type
	Operating environment	Enclosure rating		Completely closed, self-cooling, IP67 standard (excluding connector and axis through-hole area)
		Operating ambient temperature		0 to +60°C 32 to 140°F (reduced ratings at +40°C 104°F or more)
		Storage ambient temperature		-20 to +60°C -4 to +140°F
		Operating/storage ambient temperature		20 to 80% RH (no condensation)
		Operating atmosphere		Indoors (no corrosive gas, flammable gas, oil mist, or dust)
		Altitude		2000 m 6561.7' or less (reduced ratings at 1000 m 3280.8' or more)
		Vibration rank		V15
		Vibration resistance		49 m/s² 160.8'/s² with servo motor flange surface as reference (3 directions: up/down, left/right, forward/backward)
		Impact resistance		490 m/s² 1607.6'/s² with servo motor flange surface as reference, 2 times
	Isolation rank			UL: phase A, CE: phase B
	Min. insulation resistance			500 VDC, 10 MΩ or more with insulation resistance tester
	Isolation voltage tolerance			1500 VAC for 1 minute
	Approved standards	UL/CSA standards		UL1004-1, UL1004-6, CSA C22.2 No.100
		CE marking	Low-voltage directive	EN60034-1, EN60034-5
			EMI	EN55011 Class A, EN61800-3, EN61000-6-4
			EMS	EN61800-3, EN61000-6-2
		North America EMI standard		FCC Part15 B, ICES-003. Class A
	Allowable load inertia moment			35 ×
	Approx. weight			0.7 kg
Electromagnetic brake specifications	Capacity			5.5 W
	Rated voltage			24 VDC ±10%
	Rated current (@20°C 68°F)			0.23 A
	Holding torque			0.318 N·m
	Release time			60 ms ^*2
	Operating time			100 ms ^*2
^1 50 W to 750 W rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 200 × 200 × 6 mm 7.87" × 7.87" × 0.24" (50 W / 100 W) or 250 × 250 × 6 mm 9.84" × 9.84" × 0.24" (200 W to 750 W) mountable aluminum heat sink. 1 kW to 5 kW rated torque is continuously allowable with ambient temperatures of 40°C 104°F and 400 × 400 × 20 mm 15.75" × 15.75" × 0.79" (1 kW to 2 kW) or 550 × 550 × 30 mm 21.65" × 21.65" × 1.18" (3 kW to 5 kW) mountable aluminum heat sink. ^2 The release time and operation time of the electromagnetic brake vary depending on the discharge circuit.

Previous Page 261 / 290Next