keyence

€2.412,95

Only 5 units left

Specifications

Model				SL-V47F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			12.4^*1
	OFF→ON			52.4^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	112^*6
			Receiver	85^*6
		When the center indicator is OFF	Transmitter	107^*6
			Receiver	78^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			390 g
	Receiver			405 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V47FM Keyence

€0,00

Sold Out

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V47FM-R Keyence

€275,95

Only 1 unit left

Specifications

Model				SL-V47FM
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			12.4^*1
	OFF→ON			52.4^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	112^*6
			Receiver	85^*6
		When the center indicator is OFF	Transmitter	107^*6
			Receiver	78^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			1,150 g
	Receiver			1,160 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V48H Keyence

€2.744,95

Only 9 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V48H-R Keyence

€6.234,95

Only 5 units left

Specifications

Model				SL-V48H
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			12.5^*1
	OFF→ON			52.5^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	113^*6
			Receiver	87^*6
		When the center indicator is OFF	Transmitter	104^*6
			Receiver	74^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			650 g
	Receiver			675 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V48H-T Keyence

€6.234,95

Only 5 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V48HM Keyence

€2.770,95

Only 3 units left

Specifications

Model				SL-V48HM
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			12.5^*1
	OFF→ON			52.5^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	113^*6
			Receiver	87^*6
		When the center indicator is OFF	Transmitter	104^*6
			Receiver	74^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			1,980 g
	Receiver			2,000 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V48HM-R Keyence

€2.980,95

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V48HM-T Keyence

€2.980,95

Only 6 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V52H Keyence

€1.355,95

Only 1 unit left

Specifications

Model				SL-V52H
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			13.1^*1
	OFF→ON			53.1^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	117^*6
			Receiver	88^*6
		When the center indicator is OFF	Transmitter	109^*6
			Receiver	74^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			700 g
	Receiver			725 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V52HM Keyence

€4.487,95

Only 3 units left

Specifications

Model				SL-V52HM
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			13.1^*1
	OFF→ON			53.1^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	117^*6
			Receiver	88^*6
		When the center indicator is OFF	Transmitter	109^*6
			Receiver	74^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			2,130 g
	Receiver			2,150 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V52HM-T Keyence

€2.708,95

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V52HS Keyence

€905,95

Only 3 units left

Buy the Keyence SL-V52HS - a genuine Keyence industrial automation component engineered for reliable performance in demanding manufacturing and process control environments. The Keyence SL-V52HS is a direct drop-in replacement for existing installations and ships ready for integration.

Keyence SL-V55F Keyence

€2.605,95

Only 6 units left

Specifications

Model				SL-V55F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			13.5^*1
	OFF→ON			53.5^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	121^*6
			Receiver	87^*6
		When the center indicator is OFF	Transmitter	115^*6
			Receiver	80^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			450 g
	Receiver			465 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V55FM Keyence

€835,95

Only 1 unit left

Specifications

Model				SL-V55FM
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			13.5^*1
	OFF→ON			53.5^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	121^*6
			Receiver	87^*6
		When the center indicator is OFF	Transmitter	115^*6
			Receiver	80^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			1,300 g
	Receiver			1,320 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V56H Keyence

€4.968,95

Only 9 units left

Specifications

Model				SL-V56H
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			13.6^*1
	OFF→ON			53.6^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	122^*6
			Receiver	90^*6
		When the center indicator is OFF	Transmitter	112^*6
			Receiver	75^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			750 g
	Receiver			775 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V56H-R Keyence

€818,95

Only 4 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V56H-T Keyence

€1.884,95

Only 4 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V56HM Keyence

€0,00

Sold Out

Specifications

Model				SL-V56HM
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			13.6^*1
	OFF→ON			53.6^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	122^*6
			Receiver	90^*6
		When the center indicator is OFF	Transmitter	112^*6
			Receiver	75^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			2,270 g
	Receiver			2,290 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V60H Keyence

€2.483,95

Only 3 units left

Specifications

Model				SL-V60H
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			14.2^*1
	OFF→ON			54.2^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	126^*6
			Receiver	91^*6
		When the center indicator is OFF	Transmitter	116^*6
			Receiver	76^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			800 g
	Receiver			835 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V60H-R Keyence

€1.137,95

Only 4 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V60HM Keyence

€3.594,95

Only 3 units left

PLC Direct is not an authorized distributor. We offer a broad range of in-stock products with minimal lead time.

Keyence SL-V60HM-R Keyence

€3.549,95

Only 5 units left

Specifications

Model				SL-V60HM
Detection capability				ø0.98" ø25 mm
Beam axis spacing/Lens diameter				20 mm/ø5 mm 0.79"/ø0.20"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 9 m
Response time (ms)	ON→OFF			14.2^*1
	OFF→ON			54.2^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	126^*6
			Receiver	91^*6
		When the center indicator is OFF	Transmitter	116^*6
			Receiver	76^*6
Environmental resistance	Enclosure rating			IP65/67 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			2,420 g
	Receiver			2,440 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Keyence SL-V63F Keyence

€1.542,95

Only 1 unit left

Specifications

Model				SL-V63F
Detection capability				ø0.55" ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm 0.39"/ø0.16"
Effective aperture angle				Max. ±2.5 ° (When operating distance is 3 m 98.23' or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			14.6^*1
	OFF→ON			54.6^*1
Light source				Infrared LED (850 nm)
Operation mode				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max. l oad current			500 mA^*2
	Residual vol tage (during ON)			Max. 2.5 V (with a cable length of 7 m 22.97')
	Leakage current			Max. 100 µA^*3
	Max. capacitive load			2.2 µF (with a load resistance of 100 Ω)
	Load wiring resistance			Max. 2.5 Ω^*4
Non safety-rel ated output	AUX			Output with automatic PNP/NPN switching function, 50 mA max.
	Interlock-reset-ready output
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5 can be connected
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
Protection circuit				Reverse current protection, short-circuit protection for each output, surge protection for each output
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	Safety			IEC61496-1, EN61496-1, UL61496-1 (Type 4 ESPE) IEC61496-2, UL61496-2, EN61496-2 (Type 4 AOPD) IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	Power voltage			24 VDC +10 %, -20 %, Ripple (P-P) 10 % or less
	Current consumption (mA)	When the center indicator is ON	Transmitter	129^*6
			Receiver	89^*6
		When the center indicator is OFF	Transmitter	122^*6
			Receiver	82^*6
Environmental resistance	Enclosure rating			IP65 (IEC60529)
	Overvoltage category			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C 14 to 131 °F (No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	Storage temperature			-25 to +60 °C -13 to 140 °F (No freezing)
	Storage relative humidity			15 to 95 % RH
	Vibration resistance			10 to 55 Hz, Double amplitude 0.7 mm 0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s² (Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	Main unit case			Aluminum
	Upper case/lower case			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			510 g
	Receiver			525 g
^1 When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. e.g. When connecting the SL-V32H (32 beam axes), SL-V24H (24 beam axes), and SL-V12L (12 beam axes) in series, the response time of each unit is 10.3 ms, 9.2 ms, and 7.6 ms respectively, and the response time (ON to OFF) is 10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms. ^2 When used under ambient temperature between 45 to 55 °C 113 to 131 °F , the maximum should not exceed 300 mA. ^3 Applies to situations when power is either off or disconnected. ^4 The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5 When used under ambient temperature between 45 to 55 °C 113 to 131 °F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6 The current consumption of the transmitter increases by 10 mA and decreases on the receiver by 10 mA when the AUX output (red wire of the transmitter) and the EDM input (red wire of the receiver) are short circuited if the fol lowing additional condition is met. (The total consumption of both transmitter and receiver is fixed.) In the case where the PNP output type cabl e is used, the condition is that OSSD stays in the OFF state. In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.