1 year warranty
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon X80 |
| Product or Component Type | Discrete I/O module |
| Product Specific Application | For severe environments |
| Discrete input number | 8 |
| Input type | Current sink (logic positive) |
| Discrete input voltage | 24 V DC positive |
| Discrete input current | 3.5 mA |
| Discrete output number | 8 |
| Discrete output type | Solid state |
| Discrete output voltage | 24 V 19...30 V DC 140 °F (60 °C) 24 V 26.4 V DC 158 °F (70 °C) |
| Discrete output current | 0.5 A |
Complementary
| Characteristic | Value(s) |
|---|---|
| Input compatibility | With 2-wire/3-wire proximity sensors IEC 60947-5-2 With 2-wire/3-wire proximity sensors IEC 61131-2 type 3 |
| Sensor power supply | 21.1...29.0 V 158 °F (70 °C) 19...30 V 140 °F (60 °C) |
| Current state 1 guaranteed | >= 3 mA |
| Current state 0 guaranteed | <= 1.5 mA |
| Current per channel | 0.55 A 158 °F (70 °C) 0.625 A 140 °F (60 °C) |
| Maximum current per module | 5 A 140 °F (60 °C) 4.4 A 158 °F (70 °C) |
| Maximum leakage current | 0.5 mA at state 0 |
| Maximum voltage drop | <1.2 V at state 1 |
| Input impedance | 6800 Ohm |
| Insulation resistance | > 10 MOhm 500 V DC |
| Power dissipation in W | 3.7 W |
| DC typical response time | 4 ms |
| DC maximum response time | 7 ms |
| Response time on output | 1.2 ms |
| Paralleling of outputs | Yes : 2 maximum |
| Typical current consumption | 79 mA 3.3 V DC 59 mA 24 V DC |
| Current consumption | <= 111 mA 3.3 V DC <= 67 mA 24 V DC |
| MTBF reliability | 450000 H |
| Protection type | 1 external fuse per group of input channel 0.5 A fast blow overvoltage protection on output reverse polarity protection on input reverse polarity protection on output |
| Output overload protection | With electronic circuit breaker 1.5 In < Id < 2 In With current limiter |
| Output overvoltage protection | With transil diode |
| Output short-circuit protection | With 2 A external fuse |
| Reverse polarity protection | Reverse mounted diode |
| Voltage detection threshold | < 14 V DC preactuator fault < 14 V DC sensor fault > 18 V DC preactuator OK > 18 V DC sensor OK |
| Maximum tungsten load | 6 W |
| Switching frequency | 0.5/LI² Hz |
| Maximum overload time | 15 ms |
| Load impedance ohmic | >= 48 Ohm |
| Status LED | 1 LED (Green) module operating (RUN) 1 LED per channel (Green) channel diagnostic 1 LED (Red) module error (ERR) 1 LED (Red) module I/O |
| Product Weight | 0.254 lb(US) (0.115 kg) |
discrete input module M340 - 32 inputs - 24 V DC positive
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon X80 |
| Product or Component Type | Analog input module |
| Product Specific Application | For severe environments |
| Electrical connection | 40 ways 1 connector |
| Isolation between channels | Isolated |
| Input level | Low level |
| Analogue input number | 4 |
| Analogue input type | Voltage +/- 1.28 V Voltage +/- 160 mV Voltage +/- 320 mV Voltage +/- 40 mV Voltage +/- 640 mV Voltage +/- 80 mV Resistor 400 Ohm 2 wires Resistor 400 Ohm 3 wires Resistor 400 Ohm 4 wires Resistor 4000 Ohm 2 wires Resistor 4000 Ohm 3 wires Resistor 4000 Ohm 4 wires Temperature probe -100...+260 °C Cu 10 Temperature probe -100...+450 °C Pt 100 UL/JIS Temperature probe -100...+450 °C Pt 1000 UL/JIS Temperature probe -200...+850 °C Pt 100 IEC Temperature probe -200...+850 °C Pt 1000 IEC Temperature probe -60...+180 °C Ni 100 Temperature probe -60...+180 °C Ni 1000 Thermocouple +130...+1820 °C thermocouple B Thermocouple +270...+1300 °C thermocouple N Thermocouple -200...+600 °C thermocouple U Thermocouple -200...+760 °C thermocouple J Thermocouple -200...+900 °C thermocouple L Thermocouple -270...+1000 °C thermocouple E Thermocouple -270...+1370 °C thermocouple K Thermocouple -270...+400 °C thermocouple T Thermocouple -50...+1769 °C thermocouple R Thermocouple -50...+1769 °C thermocouple S |
Complementary
| Characteristic | Value(s) |
|---|---|
| Analog/digital conversion | Sigma delta 16 bits |
| Analogue input resolution | 15 bits + sign |
| Permitted overload on inputs | +/- 7.5 V +/- 1.28 V +/- 7.5 V +/- 160 mV +/- 7.5 V +/- 320 mV +/- 7.5 V +/- 40 mV +/- 7.5 V +/- 640 mV +/- 7.5 V +/- 80 mV |
| Common mode rejection | 120 dB 50/60 Hz |
| Differential mode rejection | 60 dB 50/60 Hz |
| Cold junction compensation | External by Pt100 probe |
| Type of filter | First order digital filtering |
| Nominal read cycle time | 200 ms with thermocouple 400 ms with temperature probe |
| Measurement error | +/- 0.7 °C Ni 1000 25 °C +/- 2.1 °C Ni 100 25 °C +/- 2.1 °C Pt 100 25 °C +/- 2.1 °C Pt 1000 25 °C +/- 2.7 °C thermocouple U 25 °C +/- 2.8 °C thermocouple J 25 °C +/- 3 °C thermocouple L 25 °C +/- 3.2 °C thermocouple R 25 °C +/- 3.2 °C thermocouple S 25 °C +/- 3.5 °C thermocouple B 25 °C +/- 3.7 °C thermocouple E 25 °C +/- 3.7 °C thermocouple K 25 °C +/- 3.7 °C thermocouple N 25 °C +/- 3.7 °C thermocouple T 25 °C +/- 4 °C Cu 10 25 °C 0.05 % of full scale +/- 1.28 V 25 °C 0.05 % of full scale +/- 160 mV 25 °C 0.05 % of full scale +/- 320 mV 25 °C 0.05 % of full scale +/- 40 mV 25 °C 0.05 % of full scale +/- 640 mV 25 °C 0.05 % of full scale +/- 80 mV 25 °C 0.12 % of full scale 400 Ohm 25 °C 0.12 % of full scale 4000 Ohm 25 °C +/- 1.5 °C Ni 1000 - 25...70 °C +/- 3.5 °C Ni 100 - 25...70 °C +/- 3.5 °C Pt 100 - 25...70 °C +/- 3.5 °C Pt 1000 - 25...70 °C +/- 4.5 °C Cu 10 - 25...70 °C +/- 5.5 °C thermocouple J - 25...70 °C +/- 5.5 °C thermocouple L - 25...70 °C +/- 5.5 °C thermocouple R - 25...70 °C +/- 5.5 °C thermocouple S - 25...70 °C +/- 5.5 °C thermocouple U - 25...70 °C +/- 6 °C thermocouple B - 25...70 °C +/- 6 °C thermocouple E - 25...70 °C +/- 6 °C thermocouple K - 25...70 °C +/- 6 °C thermocouple N - 25...70 °C +/- 6 °C thermocouple T - 25...70 °C <= 0.2 % of full scale +/- 1.28 V - 25...70 °C <= 0.2 % of full scale +/- 160 mV - 25...70 °C <= 0.2 % of full scale +/- 320 mV - 25...70 °C <= 0.2 % of full scale +/- 40 mV - 25...70 °C <= 0.2 % of full scale +/- 640 mV - 25...70 °C <= 0.2 % of full scale +/- 80 mV - 25...70 °C <= 0.3 % of full scale 400 Ohm - 25...70 °C <= 0.3 % of full scale 4000 Ohm - 25...70 °C |
| Temperature drift | 25 ppm/°C 400 Ohm 25 ppm/°C 4000 Ohm 25 ppm/°C Ni 1000 25 ppm/°C thermocouple B 25 ppm/°C thermocouple E 25 ppm/°C thermocouple J 25 ppm/°C thermocouple K 25 ppm/°C thermocouple L 25 ppm/°C thermocouple N 25 ppm/°C thermocouple R 25 ppm/°C thermocouple S 25 ppm/°C thermocouple T 25 ppm/°C thermocouple U 30 ppm/°C +/- 1.28 V 30 ppm/°C +/- 160 mV 30 ppm/°C +/- 320 mV 30 ppm/°C +/- 40 mV 30 ppm/°C +/- 640 mV 30 ppm/°C +/- 80 mV 30 ppm/°C Cu 10 30 ppm/°C Ni 100 30 ppm/°C Pt 100 30 ppm/°C Pt 1000 |
| Recalibration | Internal |
| Detection type | Open circuit Cu 10 Open circuit Ni 100 Open circuit Ni 1000 Open circuit Pt 100 Open circuit Pt 1000 Open circuit thermocouple B Open circuit thermocouple E Open circuit thermocouple J Open circuit thermocouple K Open circuit thermocouple L Open circuit thermocouple N Open circuit thermocouple R Open circuit thermocouple S Open circuit thermocouple T Open circuit thermocouple U |
| Maximum wiring resistance | 20 Ohm 2 wires Cu 10 20 Ohm 2 wires Ni 100 20 Ohm 2 wires Pt 100 20 Ohm 3 wires Cu 10 20 Ohm 3 wires Ni 100 20 Ohm 3 wires Pt 100 200 Ohm 2 wires Ni 1000 200 Ohm 2 wires Pt 1000 200 Ohm 3 wires Ni 1000 200 Ohm 3 wires Pt 1000 50 Ohm 4 wires Cu 10 50 Ohm 4 wires Ni 100 50 Ohm 4 wires Pt 100 500 Ohm 4 wires Ni 1000 500 Ohm 4 wires Pt 1000 |
| Measurement resolution | 0.1 °C Cu 10 0.1 °C Ni 100 0.1 °C Ni 1000 0.1 °C Pt 100 0.1 °C Pt 1000 0.1 °C thermocouple B 0.1 °C thermocouple E 0.1 °C thermocouple J 0.1 °C thermocouple K 0.1 °C thermocouple L 0.1 °C thermocouple N 0.1 °C thermocouple R 0.1 °C thermocouple S 0.1 °C thermocouple T 0.1 °C thermocouple U 1280/2exp14 mV +/- 1.28 V 160/2exp14 mV +/- 160 mV 320/2exp14 mV +/- 320 mV 40/2exp14 mV +/- 40 mV 12.5 mOhm 400 Ohm 125 mOhm 4000 Ohm 640/2exp14 mV +/- 640 mV 80/2exp14 mV +/- 80 mV |
| Maximum conversion value | +/- 100 % 400 Ohm +/- 100 % 4000 Ohm +/- 102.5 % +/- 1.28 V +/- 102.5 % +/- 160 mV +/- 102.5 % +/- 320 mV +/- 102.5 % +/- 40 mV +/- 102.5 % +/- 640 mV +/- 102.5 % +/- 80 mV |
| MTBF reliability | 1400000 H |
| Operating altitude | 0...6561.68 ft (0...2000 m) 2000...5000 m with derating factor |
| Status LED | 1 LED (Green) RUN 1 LED per channel (Green) channel diagnostic 1 LED (Red) ERR 1 LED (Red) I/O |
| Product Weight | 0.298 lb(US) (0.135 kg) |
| Current consumption | 150 mA 3.3 V DC |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon X80 |
| Product or Component Type | Analog output module |
| Product Specific Application | For severe environments |
| Electrical connection | 20 ways 1 connector |
| Isolation between channels | Isolated |
Complementary
| Characteristic | Value(s) |
|---|---|
| Measurement error | 0.1 % of full scale 25 °C <= 0.45 % of full scale - 25...70 °C |
| Temperature drift | 30 ppm/°C |
| Recalibration | Factory calibrated |
| Minimum crosstalk attenuation | 90 dB |
| EMI/RFI Noise rejection (100 kHz to 10 MHz) | 100 dB |
| Isolation voltage | 1400 V DC between channels and ground 1400 V DC between channels and bus 750 V DC between channels |
| Detection type | Open circuit 0...20 mA Open circuit 4...20 mA Short circuit +/- 10 V |
| Load impedance ohmic | <= 600 Ohm 0...20 mA <= 600 Ohm 4...20 mA >= 1000 Ohm +/- 10 V |
| Output level | High level |
| Analogue output number | 2 |
| Analogue output type | Current 0...20 mA Current 4...20 mA Voltage +/- 10 V |
| Analogue output resolution | 15 bits + sign |
| Supply | Internal power supply via rack |
| Conversion time | <= 1 ms |
| Maximum conversion value | +/- 11.25 V +/- 10 V 0...24 mA 0...20 mA 0...24 mA 4...20 mA |
| Fallback mode | Configurable Predefined |
| MTBF reliability | 1300000 H |
| Operating altitude | 0...6561.68 ft (0...2000 m) 2000...5000 m with derating factor |
| Status LED | 1 LED (Green) RUN 1 LED per channel (Green) channel diagnostic 1 LED (Red) ERR 1 LED (Red) I/O |
| Product Weight | 0.317 lb(US) (0.144 kg) |
| Power consumption in W | 2.1 W 24 V DC typical 2.8 W 24 V DC maximum 0.35 W 3.3 V DC typical 0.48 W 3.3 V DC maximum |
mixed analog I/O module M340 - 4 inputs 0..20 mA - 2 outputs 0..20 mA
This product is part of the Modicon X80 range, a common platform of modules for Modicon M580 and M340 Programmable Automation Controllers (PAC). This discrete input module has 8 capacitive inputs. It is an input module with an input voltage of 200V AC to 240V AC, a current consumption of 76mA at 3.3V DC, 93.6mA at 24V DC and a power dissipation 4.73W. There is an isolation between channels. This product is robust, high quality and based on the latest innovative technology. It has an external fuse per group of channel 0.5A fast blow protection type. It is an IP20 rated product. It weighs 0.12kg. It is suitable for medium to large process applications. This product is certified by EAC, RCM, UL, CSA, Merchant Navy, CE. It meets IEC 61131-2, CSA C22.2 No 142, CSA C22.2 No 213 and UL 508 standards. This input module is compatible with 2-wire/3-wire proximity sensors conforming to IEC 60947-5-2. Modicon X80 consists in a compatible modules common platform that reduce maintenance and training costs with same spare parts in stock, and unique training for different Programmable Automation Controllers (PAC).
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon X80 |
| Product or Component Type | Discrete input module |
| Discrete input number | 8 |
| Discrete input type | Isolated |
| Input type | Capacitive |
| Discrete input voltage | 200...240 V AC |
| Discrete input current | 10.4 mA |
Complementary
| Characteristic | Value(s) |
|---|---|
| Input compatibility | With 2-wire/3-wire proximity sensors IEC 60947-5-2 With 2-wire/3-wire proximity sensors IEC 61131-2 Type 2 |
| Network Frequency | 50/60 Hz |
| Network frequency limits | 47â¦63 Hz |
| Sensor power supply | 170...264 V |
| Current state 1 guaranteed | >= 6 mA |
| Current state 0 guaranteed | <= 4 mA |
| Input impedance | 21000 Ohm |
| Insulation resistance | > 10 MOhm 500 V DC |
| Power dissipation in W | 4.73 W |
| AC activation response time | 10 ms |
| AC deactivation response time | 20 ms |
| Typical current consumption | 76 mA 3.3 V DC 93.6 mA 24 V DC |
| Current consumption | <= 126 mA 3.3 V DC <= 154.8 mA 24 V DC |
| MTBF reliability | 1700000 H |
| Protection type | 1 external fuse per group of channel 0.5 A fast blow |
| Voltage detection threshold | > 164 V AC sensor OK < 80 V AC sensor fault |
| Status LED | 1 LED (Green) module operating (RUN) 1 LED per channel (Green) channel diagnostic 1 LED (Red) module error (ERR) 1 LED (Red) module I/O |
| Product Weight | 0.26 lb(US) (0.12 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 4 |
| Electrical connection | 1 pre-wired cable connector, 32.8 ft (10 m) 4 female connectors M12 5 pins |
| Status LED | Without |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 8 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 3.7 lb(US) (1.7 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 8 |
| Electrical connection | 1 male plug-in connector 8 female connectors M12 5 pins |
| Status LED | 1 LED per channel (Yellow) channel status 2 LEDs (Green) power ON |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 16 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 0.2 lb(US) (0.1 kg) |
OPC UA module for M580 harsh environments
analog ouput module X80 - 4 outputs HART - current Isolated
analog input module M340 - 4 inputs 0..20 mA
Sub-base with plug-in electromechanical relay ABE7 - 16 channels - relay 12.5 mm
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 4 |
| Electrical connection | 1 pre-wired cable connector, 16.4 ft (5 m) 4 female connectors M12 5 pins |
| Status LED | Without |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 8 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 1.50 lb(US) (0.68 kg) |
This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system. This sub-base for plug-in relay, provides 16 channels. This product enables rapid connection of I/O modules. It is a relay sub base with a supply voltage of 19V to 30V DC and a maximum supply current of 1A. It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product. It weighs 0.615kg. It is suitable for all types of industrial applications. This product is certified by GL, CSA, DNV, BV, LROS and UL. This sub-base is suitable for use with ABR7S2, ABS7SA2, ABS7SC2 and ABE7ACC20 connection sub-base accessory. The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit). Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment. Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon ABE7 |
| Product or Component Type | Sub-base for plug-in relay |
| Sub-base type | Output sub-base |
| [Us] rated supply voltage | 19...30 V IEC 61131-2 |
| Number of channels | 16 |
| Connections - terminals | Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 24...AWG 14) solid |
Complementary
| Characteristic | Value(s) |
|---|---|
| supply voltage type | DC |
| Product Compatibility | ABS7SC2. ABR7S2. ABS7SA2. ABE7ACC20 |
| Status LED | 1 LED per channel (Green) channel status 1 LED (Green) power ON |
| Polarity distribution | Volt-free |
| Short-circuit protection | 1 A internal fuse, 5 x 20 mm, fast blow PLC end) |
| Fixing mode | By clips (35 mm symmetrical DIN rail) By screws (solid plate with fixing kit) |
| Maximum supply current | 1 A |
| Voltage drop on power supply fuse | 0.3 V |
| Maximum current per output common | 16 A |
| [Ui] rated insulation voltage | 300 V coil circuit/contact circuits IEC 60947-1 2000 V terminals/mounting rails |
| [Uimp] rated impulse withstand voltage | 2.5 kV |
| Installation category | II IEC 60664-1 |
| Tightening torque | 5.3 lbf.in (0.6 N.m) flat à 3.5 mm |
| Product Weight | 1.356 lb(US) (0.615 kg) |
AS-BADU-214 AS BADU I_O INPUT MODULE ANALOG 8POINT TC RTD MV 4-20MA +/-MA - 984 Series
battery control module - 24..28.8 V DC - 24 V - 40 A - for regulated SMPS
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 4 |
| Electrical connection | 1 pre-wired cable connector, 32.8 ft (10 m) 4 female connectors M12 5 pins |
| Status LED | 1 LED per channel (Yellow) channel status 2 LEDs (Green) power ON |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 8 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 3.7 lb(US) (1.7 kg) |
This product is part of the Advantys ABE9 range, an offer of IP67 passive splitters boxes. This passive splitter box for M12 connectors make it possible to eliminate long and difficult cabling operations. It provides 8 channels and 16 ways. It is furnished with 5-pin female M12 connectors and 5m pre-wired cable connector for electrical connection. It is a splitter box with an operational voltage of 24V DC and a current per channel of 4A. A single yellow LED is equipped for channel status and dual green LED's for power ON. It is an IP67 rated product. It weighs 1.61kg. The splitter box is suitable for packaging, bottling, assembly and conveying applications. This product is certified by CULus. Its modularity and dimensions mean they are the ideal solution for a wide variety of customer applications.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 8 |
| Electrical connection | 1 pre-wired cable connector, 16.4 ft (5 m) 8 female connectors M12 5 pins |
| Status LED | 1 LED per channel (Yellow) channel status 2 LEDs (Green) power ON |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 16 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 3.55 lb(US) (1.61 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon ABE7 |
| Product or Component Type | Solid state input relay sub-base |
| [Us] rated supply voltage | 230/240 V AC 50/60 Hz sensor end) 24 V DC PLC end) |
| Number of channels | 16 |
| Number of terminal per channel | 2 |
| Connections - terminals | Screw type terminals, 1 x 0.09...1 x 1.5 mm², 0.0001â¦0.002 in² (0.09â¦1.5 mm²) AWG 28...AWG 16) flexible with cable end Screw type terminals, 1 x 0.14...1 x 2.5 mm², 0.0002â¦0.004 in² (0.14â¦2.5 mm²) AWG 26...AWG 12) solid Screw type terminals, 1 x 0.14...1 x 2.5 mm², 0.0002â¦0.004 in² (0.14â¦2.5 mm²) AWG 26...AWG 14) flexible without cable end Screw type terminals, 2 x 0.09...2 x 0.75 mm², 0.0001â¦0.001 in² (0.09â¦0.75 mm²) AWG 28...AWG 20) flexible with cable end Screw type terminals, 2 x 0.2...2 x 2.5 mm², 0.0003â¦0.004 in² (0.2â¦2.5 mm²) AWG 24...AWG 14) solid |
Complementary
| Characteristic | Value(s) |
|---|---|
| Terminal block type | Removable |
| Supply voltage limits | 19â¦30 V DC PLC end)IEC 61131-2 |
| Isolation PLC/operative part | Yes |
| Protection type | Internal fuse 1 A 5 x 20 mm fast blow PLC end Adjustable by external fuse fast blow sensor end |
| Fixing mode | By clips (35 mm symmetrical DIN rail) By screws (solid plate with fixing kit) |
| Current per channel | 0.008 A |
| Current state 1 guaranteed | >= 4.5 mA sensor end) |
| Voltage state 1 guaranteed | >= 164 V sensor end |
| Maximum switching current | 15 mA PLC end) |
| Minimum switching current | 1 mA for PLC end |
| Response time | <= 20 ms from state 0 to 1 <= 20 ms from state 1 to 0 |
| Switching frequency | <= 25 Hz 50 % |
| [Uimp] rated impulse withstand voltage | 2.5 kV IEC 60947-1 |
| [Ui] Rated Insulation Voltage | 2000 V |
| Installation category | II IEC 60664-1 |
| Tightening torque | 5.3 lbf.in (0.6 N.m) flat à 3.5 mm |
| Product Weight | 0.897 lb(US) (0.407 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 8 |
| Electrical connection | 1 pre-wired cable connector, 16.4 ft (5 m) 8 female connectors M12 5 pins |
| Status LED | Without |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 16 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 3.55 lb(US) (1.61 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 4 |
| Electrical connection | 1 male connector M23 19 pins 4 female connectors M12 5 pins |
| Status LED | 1 LED (Green) power ON 1 LED per channel (Yellow) channel status |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 8 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without |
| Product Weight | 0.18 lb(US) (0.08 kg) |
This product is part of the Modicon ABE7 range, an offer of connection sub-bases for Telefast pre-wired system. This passive connection sub-base provides 16 modularity input/output channels and an isolator. It has 2 terminals per channel. It is a sub base with a maximum supply current of 1.8A and a rated supply voltage of 19V to 30V. It is furnished with screw clamp terminals for electrical connection. It is an IP2x rated product. Its dimension is 125mm (Width). It weighs 0.375kg. It is suitable for all types of industrial applications. This product is certified by GL, BV, CSA, UL, DNV and LROS. The fixing is done by clips (35mm symmetrical DIN rail) and screws (solid plate with fixing kit). Modicon ABE7 means greater simplicity to rationalise wiring in automation system equipment. Pre-wired system enabling connection and adaptation of control signals of PLC cards equipped with HE10 connectors.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon ABE7 |
| Product or Component Type | Passive discrete I/O sub-base |
| Sub-base type | I/O sub-base |
| [Us] rated supply voltage | 19...30 V IEC 61131-2 |
| Number of channels | 16 |
| Number of terminal per channel | 2 |
| Connections - terminals | Screw type terminals, 1 x 0.09...1 x 1.5 mm² AWG 28...AWG 16) flexible with cable end Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 12) solid Screw type terminals, 1 x 0.14...1 x 2.5 mm² AWG 26...AWG 14) flexible without cable end Screw type terminals, 2 x 0.09...2 x 0.75 mm² AWG 28...AWG 20) flexible with cable end Screw type terminals, 2 x 0.2...2 x 2.5 mm² AWG 24...AWG 14) solid |
| Channel additional information | 1 switch disconnector per channel |
Complementary
| Characteristic | Value(s) |
|---|---|
| supply voltage type | DC |
| Number of horizontal rows | 2 |
| Status LED | 1 LED per channel (Green) channel status 1 LED (Green) power ON |
| Polarity distribution | 0 V or 24 V |
| Short-circuit protection | 2 A internal fuse, 5 x 20 mm, fast blow PLC end) |
| Connector Type | HE-10 |
| Pin number | 20 pins |
| Fixing mode | By clips (35 mm symmetrical DIN rail) By screws (solid plate with fixing kit) |
| Maximum supply current | 1.8 A |
| Current per channel | 0.5 A |
| Maximum current per output common | 1.8 A |
| Voltage drop on power supply fuse | 0.3 V |
| [Ui] Rated Insulation Voltage | 2000 V |
| Installation category | II IEC 60664-1 |
| Tightening torque | 5.3 lbf.in (0.6 N.m) flat à 3.5 mm |
| Width | 4.9 in (125 mm) |
| Product Weight | 0.827 lb(US) (0.375 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys ABE9 |
| Product or Component Type | IP67 passive splitter box |
| Number of channels | 4 |
| Electrical connection | 1 pre-wired cable connector, 16.4 ft (5 m) 4 female connectors M12 5 pins |
| Status LED | 1 LED per channel (Yellow) channel status 2 LEDs (Green) power ON |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of ways | 8 ways |
| [Ue] rated operational voltage | 24 V DC |
| Current per channel | 4 A |
| Insulation group | Category 3 VDE 0110 |
| Operating position | Any position |
| Fixing Mode | M4 screw fixing |
| Contact resistance | 5000 µOhm |
| Current of common | 16 A 0.002 in² (1 mm²) 12 A 0.001 in² (0.75 mm²) |
| Separation of commons | Without or with |
| Product Weight | 1.50 lb(US) (0.68 kg) |
Sub-base with plug-in electromechanical relay ABE7 - 16 channels - relay 12.5 mm
Main category name:Modules Sub category name:Modules Vendor:Schneider