1 year warranty
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard digital output kit |
| Kit composition | STBXTS1100, 5-terminal screw type connector STBDAO8210 module STBXTS2110, 5-terminal spring clamp connector STBXBA2000 base |
| Discrete output number | 2 |
| Discrete output type | Triac |
| Discrete output voltage | 115...230 V |
| Discrete output voltage type | AC |
Complementary
| Characteristic | Value(s) |
|---|---|
| Discrete output current | 1000 mA 140 °F (60 °C) 2000 mA 86 °F (30 °C) |
| Discrete output logic | Positive or negative |
| Output voltage | 20...265 V AC |
| Absolute maximum voltage | 300 V 10 s 400 V 20 ms |
| Response Time | 10 ms off-to-on 10.5 ms on-to-off |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| fallback | State 0 basic NIMs User configurable standard NIMs |
| Protection type | Output surge protection varistance and RC circuit |
| Insulation between channels and logic bus | 1780 V for 1 minute |
| Maximum leakage current | 2 mA at state 0 115 V 2.5 mA at state 0 230 V |
| Surge current | 20 A 40 ms 30 A 20 ms |
| Minimum load | 5 mA |
| Reset | Manual or automatic reset COM fault |
| Product Compatibility | I/O base STBXBA2000 Power distribution module STBPDT2100/2105 |
| Supply | Power distribution module |
| Current consumption | 45 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED per channel (Green) channel status (OUT1 to OUT2) 1 LED (Red) module error (ERR) |
| Height | 0.7 in (18.4 mm) |
| Depth | 2.8 in (70 mm) |
| Width | 5.05 in (128.3 mm) |
| Product Weight | 0.276 lb(US) (0.125 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard digital input module |
| Discrete input number | 6 |
| Discrete input voltage | 24 V |
| Discrete input voltage type | DC |
Complementary
| Characteristic | Value(s) |
|---|---|
| Input voltage limits | 15...30 V at state 1 -3...5 V at state 0 |
| Acceptable Input Voltage | 30 V |
| Absolute maximum voltage | 56 V 1.3 ms |
| Discrete input current | 4.5 mA |
| Current state 0 guaranteed | <= 0.5 mA |
| Current state 1 guaranteed | >= 2.5 mA |
| Discrete input logic | Positive or negative |
| Response time | 1.21 ms off-to-on 1.74 ms on-to-off |
| Protection type | Power protection integrated fuse on PDM time lag 10 A Input protection resistor-limited Reverse polarity protection |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| Input filtering | 1 ms |
| Product Compatibility | I/O base STBXBA1000 Power distribution module STBPDT3100/3105 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 55 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED per channel (Green) channel status (IN1 to IN6) 1 LED (Red) module error (ERR) |
| Depth | 2.6 in (65.1 mm) |
| Height | 0.7 in (18.4 mm) |
| Width | 4.9 in (125 mm) |
| Product Weight | 0.247 lb(US) (0.112 kg) |
This product is part of the Modicon STB range, an offer of modular distributed I/O. This standard analogue input kit is an accessory kit of Programmable Logic Controllers (PLC) and Programmable Automation Controllers (PAC). It has 8 analogue inputs (voltage ±10V, ±5V, 0V to 10V, 0V to 5V, 1V to 5V) with 15bit plus sign resolution. This product is compatible with most major fieldbus networks. It is an analogue input kit with a rated supply voltage of 24V DC and a current consumption of 90mA at 5V DC for logic bus. It supports hot swap fallback, requires standard type network interface module (NIM). It is an IP20 rated product. It is suitable for packaging, bottling, assembly, distribution, textile, printing and semiconductor machines applications. This product is certified by FM Class 1 Division 2, ATEX category 3G, CE, UL, CSA and C-Tick. This kit is suitable for use with mounting base STBXBA1000 and power distribution module STBPDT3100/3105. The kit includes STBXBA1000 base, STBAVI1400 module, STBXTS2100, 6-terminal spring clamp connector and STBXTS1100, 6-terminal screw type connector. The Modicon STB distributed I/O solution is an open, modular input/output system that makes it possible to design automation islands managed by a master controller via a bus or communication network.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard analog input kit |
| Kit composition | STBXBA1000 base STBAVI1400 module STBXTS2100, 6-terminal spring clamp connector STBXTS1100, 6-terminal screw type connector |
| Analogue input type | Voltage +/- 10 V Voltage +/- 5 V Voltage 0...10 V Voltage 0...5 V Voltage 1...5 V |
| Analogue input number | 8 |
| Analogue input resolution | 15 bits + sign |
| Type of filter | Single low pass input filter 25 Hz |
Complementary
| Characteristic | Value(s) |
|---|---|
| Absolute maximum input | 50 V DC |
| Cold swapping | Yes |
| Hot swapping fallback | Yes for standard NIMs |
| Fallback status | State 0 basic NIMs User configurable standard NIMs |
| Data format | IEC 61131-2 EN 61131-2 |
| Update time | 22 ms |
| Integral linearity | +/- 0.2 %FS |
| Differential linearity | Monotonic |
| Input impedance | 400 kOhm |
| Maximum supply current for sensors | 100 mA per input channels |
| Maximum source impedance | 1 kOhm |
| Absolute accuracy error | +/- 0.75 % of full scale 25 °C |
| Temperature Drift | +/-0.01 %/°C |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Insulation between channels and sensor bus | 30 V |
| Addressing requirement | 2 input words |
| Product Compatibility | Power distribution module STBPDT3100/3105 Mounting base STBXBA1000 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 90 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED (Red) module error (ERR) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard digital input kit |
| Kit composition | STBXTS2110, 5-terminal spring clamp connector STBXBA2000 base STBXTS1110, 5-terminal screw type connector STBDAI5230 module |
| Discrete input number | 2 |
| Discrete input voltage | 115 V |
| Discrete input voltage type | AC |
Complementary
| Characteristic | Value(s) |
|---|---|
| Input voltage limits | 0...20 V at state 0 74...132 V at state 1 |
| Acceptable Input Voltage | 132 V |
| Absolute maximum voltage | 200 V 20 ms |
| Network Frequency | 50/60 Hz |
| Network frequency limits | 47â¦63 Hz |
| Current state 0 guaranteed | <= 2 mA |
| Current state 1 guaranteed | >= 4 mA |
| Response time | 1.5 ms off-to-on 1.5 ms on-to-off |
| Protection type | Power protection integrated fuse on PDM time lag 10 A Input protection resistor-limited |
| Insulation between channels and logic bus | 1780 V for 1 minute |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| Current supplied by sensor | <= 60 mA per channel |
| Product Compatibility | I/O base STBXBA2000 Power distribution module STBPDT2100/2105 |
| [Us] rated supply voltage | 115/230 V AC |
| Supply | Power distribution module |
| Current consumption | 40 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED per channel (Green) channel status (IN1 to IN2) 1 LED (Red) module error (ERR) |
| Depth | 2.6 in (65.1 mm) |
| Height | 0.7 in (18.4 mm) |
| Width | 4.9 in (125 mm) |
| Product Weight | 0.26 lb(US) (0.12 kg) |
standard digital input kit STB - 24 V DC - 6 I
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard digital output kit |
| Kit composition | STBXBA2000 base STBDAO5260 module STBXTS1100, 5-terminal screw type connector STBXTS2110, 5-terminal spring clamp connector |
| Discrete output number | 2 |
| Discrete output type | Triac |
| Discrete output voltage | 115 V |
| Discrete output voltage type | AC |
Complementary
| Characteristic | Value(s) |
|---|---|
| Discrete output current | 1000 mA 140 °F (60 °C) 2000 mA 86 °F (30 °C) |
| Discrete output logic | Positive or negative |
| Output voltage | 74....132 V AC |
| Absolute maximum voltage | 132 V |
| Response Time | 10 ms off-to-on 10 ms on-to-off |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| fallback | State 0 basic NIMs User configurable standard NIMs |
| Protection type | Output surge protection external fuse 5 A |
| Insulation between channels | 1780 V for 1 minute |
| Insulation between channels and logic bus | 1780 V for 1 minute |
| Maximum leakage current | 2 mA at state 0 132 V |
| Surge current | 20 A 40 ms 30 A 20 ms |
| Minimum load | 1 mA |
| Reset | Manual or automatic reset COM fault |
| Product Compatibility | Power distribution module STBPDT2100/2105 I/O base STBXBA2000 |
| Supply | Power distribution module |
| Current consumption | 70 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED per channel (Green) channel status (OUT1 to OUT2) 1 LED (Red) module error (ERR) |
| Height | 0.7 in (18.4 mm) |
| Depth | 2.8 in (70 mm) |
| Width | 5.05 in (128.3 mm) |
| Product Weight | 0.148 lb(US) (0.067 kg) |
discrete I/O extension module - 6 I O - 24 V DC - for Zelio Logic
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Basic analog output kit |
| Kit composition | STBAVO1265 module STBXTS2100, 6-terminal spring clamp connector STBXTS1100, 6-terminal screw type connector STBXBA1000 base |
| Analogue output type | Voltage +/- 10 V |
| Analogue output number | 2 |
| Analogue output resolution | 9 bits + sign |
Complementary
| Characteristic | Value(s) |
|---|---|
| Analogue output current | 0.005 A |
| Response Time | 3 ms |
| Cold swapping | Yes |
| hot swapping | No for basic NIMs |
| fallback | State 0 |
| Data format | IEC 61131-2 EN 61131-2 |
| Update time | 25 ms |
| Protection Type | Short-circuit protection |
| Integral linearity | +/- 0.1 %FS |
| Differential linearity | Monotonic |
| Absolute accuracy error | +/- 0.5 % of full scale 77 °F (25 °C) |
| Temperature Drift | +/-0.01 %/°C |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Insulation between channels and actuator bus | 30 V |
| Addressing requirement | 2 output words |
| Product Compatibility | Mounting base STBXBA1000 Power distribution module STBPDT3100/3105 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 45 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) |
| Depth | 2.8 in (70 mm) |
| Height | 0.5 in (13.9 mm) |
| Width | 5.05 in (128.3 mm) |
| Product Weight | 0.254 lb(US) (0.115 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard digital input kit |
| Kit composition | STBXTS1110, 5-terminal screw type connector STBDAI7220 module STBXTS2110, 5-terminal spring clamp connector STBXBA2000 base |
| Discrete input number | 2 |
| Discrete input voltage | 230 V |
| Discrete input voltage type | AC |
Complementary
| Characteristic | Value(s) |
|---|---|
| Input voltage limits | 0...40 V at state 0 159...256 V at state 1 |
| Acceptable Input Voltage | 265 V |
| Absolute maximum voltage | 400 V 20 ms |
| Network Frequency | 50/60 Hz |
| Network frequency limits | 47â¦63 Hz |
| Current state 0 guaranteed | <= 2 mA |
| Current state 1 guaranteed | >= 4 mA |
| Response time | 1.5 ms off-to-on 1.5 ms on-to-off |
| Protection type | Power protection integrated fuse on PDM time lag 10 A Input protection resistor-limited |
| Insulation between channels and logic bus | 1780 V for 1 minute |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| Product Compatibility | Power distribution module STBPDT2100/2105 I/O base STBXBA2000 |
| [Us] rated supply voltage | 115/230 V AC |
| Supply | Power distribution module |
| Current consumption | 40 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED per channel (Green) channel status (IN1 to IN2) 1 LED (Red) module error (ERR) |
| Depth | 2.6 in (65.1 mm) |
| Height | 0.7 in (18.4 mm) |
| Width | 4.9 in (125 mm) |
| Product Weight | 0.269 lb(US) (0.122 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard analog output kit |
| Kit composition | STBACO8220 module STBXBA2000 base STBXTS2100, 6-terminal spring clamp connector STBXTS1100, 6-terminal screw type connector |
| Analogue output type | Current 4...20 mA |
| Analogue output number | 2 |
| Analogue output resolution | 15 bits + sign |
Complementary
| Characteristic | Value(s) |
|---|---|
| Analogue output current | 0.02 A |
| Response Time | 40 ms plus update time |
| Cold swapping | Yes |
| hot swapping | Yes for standard NIMs |
| fallback | State 0 basic NIMs User configurable standard NIMs |
| Data format | EN 61131-2 IEC 61131-2 |
| Update time | 8 ms |
| Integral linearity | +/- 0.05 %FS |
| Differential linearity | Monotonic |
| Absolute accuracy error | +/- 0.3 % of full scale 77 °F (25 °C) |
| Temperature Drift | +/-0.005 %/°C |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Insulation between channels and actuator bus | 200 V |
| Product Compatibility | Power distribution module STBPDT3100/3105 Mounting base STBXBA1000 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 210 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) 1 LED (Red) module error (ERR) |
| Depth | 2.8 in (70 mm) |
| Height | 0.7 in (18.4 mm) |
| Width | 5.05 in (128.3 mm) |
standard analog output kit, Modicon STB, 4 to 20mA, 2O, 15 bits with sign
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon X80 |
| Accessory / Separate Part Type | Shielding connection kit |
| Product or Component Type | Connector kit |
| Product Compatibility | 6 slot backplane |
| Accessory / separate part destination | Backplane |
| Number of slots | 6 |
Complementary
| Characteristic | Value(s) |
|---|---|
| Kit composition | A metal bar Two sub-bases |
| Product Weight | 0.68 lb(US) (0.31 kg) |
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Advantys OTB |
| Product or Component Type | Passive commoning module |
| Product Specific Application | For grouping inter-module I/O commons |
| Electrical Connection | Removable screw terminal block |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number of common point | 2 insulated groups |
| Output voltage limits | 19...30 V DC 215...240 V |
| Maximum current per output common | 8 A |
| Current per channel | 2 A |
| Product Weight | 0.2 lb(US) (0.1 kg) |
This Zelio Logic SR3 discrete I/O extension module smart relays uses a supply voltage of 24V direct current. It has 14 inputs / outputs contact with screw-clamp terminals. It enables simple ladder programming, adapted for non-specialists.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Zelio Logic |
| Product or Component Type | Discrete I/O extension module |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number or control scheme lines | 120 ladder |
| Cycle time | 6â¦90 ms |
| Backup time | 10 years 77 °F (25 °C) |
| Clock drift | 12 min/year 32â¦131 °F (0â¦55 °C) |
| Checks | Program memory on each power up |
| [Us] rated supply voltage | 24 V DC |
| Supply voltage limits | 19.2â¦30 V |
| Reverse polarity protection | With |
| Discrete input number | 8 IEC 61131-2 Type 1 |
| Discrete input type | Resistive |
| Discrete input voltage | 24 V DC |
| Discrete input current | 4 mA |
| Counting frequency | 1 kHz discrete input |
| Voltage state 1 guaranteed | >= 15 V I1...IA and IH...IR discrete input circuit >= 15 V IB...IG used as discrete input circuit |
| Voltage state 0 guaranteed | <= 5 V I1...IA and IH...IR discrete input circuit <= 5 V IB...IG used as discrete input circuit |
| Current state 1 guaranteed | >= 1.2 mA IB...IG used as discrete input circuit) >= 2.2 mA I1...IA and IH...IR discrete input circuit) |
| Current state 0 guaranteed | <= 0.5 mA IB...IG used as discrete input circuit) <= 0.75 mA I1...IA and IH...IR discrete input circuit) |
| Input compatibility | 3-wire proximity sensors PNP discrete input |
| Input impedance | 12 kOhm IB...IG used as discrete input circuit 7.4 kOhm I1...IA and IH...IR discrete input circuit |
| Number of Outputs | 6 relay |
| Output voltage limits | 24...250 V AC relay output) 5...30 V DC relay output) |
| Contacts type and composition | NO relay output |
| Output thermal current | 5 A for 2 outputs relay output 8 A for 4 outputs relay output |
| Electrical durability | AC-15 500000 cycles 230 V, 0.9 A relay output IEC 60947-5-1 AC-12 500000 cycles 230 V, 1.5 A relay output IEC 60947-5-1 DC-13 500000 cycles 24 V, 0.6 A relay output IEC 60947-5-1 DC-12 500000 cycles 24 V, 1.5 A relay output IEC 60947-5-1 |
| Switching capacity in mA | >= 10 mA 12 V relay output) |
| Operating rate in Hz | 0.1 Hz at Ie)relay output 10 Hz no load)relay output |
| Mechanical durability | 10000000 cycles relay output |
| [Uimp] rated impulse withstand voltage | 4 kV EN/IEC 60947-1 and EN/IEC 60664-1 |
| Response time | 10 ms from state 0 to state 1)relay output 5 ms from state 1 to state 0)relay output |
| Connections - terminals | Screw terminals, 1 x 0.25...1 x 2.5 mm² AWG 24...AWG 14) flexible with cable end Screw terminals, 2 x 0.25...2 x 0.75 mm² AWG 24...AWG 18) flexible with cable end Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) semi-solid Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) solid Screw terminals, 2 x 0.2...2 x 1.5 mm² AWG 24...AWG 16) solid |
| Tightening torque | 4.4 lbf.in (0.5 N.m) |
| Overvoltage category | III conforming to IEC 60664-1 |
| Product Weight | 0.49 lb(US) (0.22 kg) |
basic analog output kit STB - 4..20 mA - 2 O - 10 bits
This Schneider Electric Zelio Logic SR3 Discrete I/O Extension Module Smart Relays uses a supply voltage of 12 volts direct current, has 10 inputs / outputs contact with screw-clamp terminals. This Discrete I/O Extension Module Smart Relays provides Zelio Logic relays with additional inputs and outputs. It has a compact form-factor, allowing installation on DIN rail. Simple ladder programming, adapted for non-specialists. Discovery package, coming with Zelio Soft programming software, the simplest way to learn and use this relay. Built-in EEPROM flash memory for data backup up to 10 years, easy-to-recover after a power shortage or incident. More I/O than SR2 model, for larger applications. The main application of this module is industry and building/service sector. This product is certified by C-Tick, GL, UL, CSA and GOST. It meets EN/IEC 60068-2-27 Ea, EN/IEC 61000-4-5, EN/IEC 61000-4-12 and EN/IEC 61000-4-4 L3 standards. Easy to use, Zelio Logic provides a real alternative solutions based on cabled logic or specific cards.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Zelio Logic |
| Product or Component Type | Discrete I/O extension module |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number or control scheme lines | 120 ladder |
| Cycle time | 6â¦90 ms |
| Backup time | 10 years 77 °F (25 °C) |
| Clock drift | 12 min/year 32â¦131 °F (0â¦55 °C) |
| Checks | Program memory on each power up |
| [Us] rated supply voltage | 12 V DC |
| Supply voltage limits | 10.4â¦14.4 V |
| Reverse polarity protection | With |
| Discrete input number | 6 IEC 61131-2 Type 1 |
| Discrete input type | Resistive |
| Discrete input voltage | 12 V DC |
| Discrete input current | 4 mA |
| Counting frequency | 1 kHz discrete input |
| Voltage state 1 guaranteed | >= 7 V IB...IG used as discrete input circuit >= 5.6 V I1...IA and IH...IR discrete input circuit |
| Voltage state 0 guaranteed | <= 3 V IB...IG used as discrete input circuit <= 2.4 V I1...IA and IH...IR discrete input circuit |
| Current state 1 guaranteed | >= 2 mA I1...IA and IH...IR discrete input circuit) >= 0.5 mA IB...IG used as discrete input circuit) |
| Current state 0 guaranteed | <= 0.2 mA IB...IG used as discrete input circuit) <= 0.9 mA I1...IA and IH...IR discrete input circuit) |
| Input compatibility | 3-wire proximity sensors PNP discrete input |
| Input impedance | 14 kOhm IB...IG used as discrete input circuit 2.7 kOhm I1...IA and IH...IR discrete input circuit |
| Number of Outputs | 4 relay |
| Output voltage limits | 24...250 V AC relay output) 5...30 V DC relay output) |
| Contacts type and composition | NO relay output |
| Output thermal current | 8 A for all 4 outputs relay output |
| Electrical durability | AC-15 500000 cycles 230 V, 0.9 A relay output IEC 60947-5-1 AC-12 500000 cycles 230 V, 1.5 A relay output IEC 60947-5-1 DC-13 500000 cycles 24 V, 0.6 A relay output IEC 60947-5-1 DC-12 500000 cycles 24 V, 1.5 A relay output IEC 60947-5-1 |
| Switching capacity in mA | >= 10 mA 12 V relay output) |
| Operating rate in Hz | 0.1 Hz at Ie)relay output 10 Hz no load)relay output |
| Mechanical durability | 10000000 cycles relay output |
| [Uimp] rated impulse withstand voltage | 4 kV EN/IEC 60947-1 and EN/IEC 60664-1 |
| Response time | 10 ms from state 0 to state 1)relay output 5 ms from state 1 to state 0)relay output |
| Connections - terminals | Screw terminals, 1 x 0.25...1 x 2.5 mm² AWG 24...AWG 14) flexible with cable end Screw terminals, 2 x 0.25...2 x 0.75 mm² AWG 24...AWG 18) flexible with cable end Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) semi-solid Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) solid Screw terminals, 2 x 0.2...2 x 1.5 mm² AWG 24...AWG 16) solid |
| Tightening torque | 4.4 lbf.in (0.5 N.m) |
| Overvoltage category | III conforming to IEC 60664-1 |
| Product Weight | 0.4 lb(US) (0.2 kg) |
standard analog input kit STB - 4..20 mA - 4 I - 15 bits + sign
standard analog input kit STB - 4..20 mA - 4 I - 15 bits + sign
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Standard analog input module |
| Analogue input type | Current 0...20 mA Current 4...20 mA |
| Analogue input number | 8 |
| Analogue input resolution | 15 bits + sign |
| Type of filter | Single low pass input filter 985 Hz |
Complementary
| Characteristic | Value(s) |
|---|---|
| Absolute maximum input | 25 mA |
| Cold swapping | Yes |
| Hot swapping fallback | Yes for standard NIMs |
| Fallback status | State 0 basic NIMs User configurable standard NIMs |
| Data format | EN 61131-2 IEC 61131-2 |
| Update time | 22 ms |
| Integral linearity | +/- 0.08 %FS |
| Differential linearity | Monotonic |
| Input impedance | <= 250 Ohm |
| Maximum supply current for sensors | 100 mA per input channels |
| Absolute accuracy error | +/- 0.4 % of full scale per °C |
| Temperature Drift | +/-0.005 %/°C |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Insulation between channels and sensor bus | 30 V |
| Addressing requirement | 16 input words |
| Product Compatibility | Power distribution module STBPDT3100/3105 Mounting base STBXBA2000 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 90 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) |
| Depth | 2.8 in (70 mm) |
| Height | 0.7 in (18.4 mm) |
| Width | 5.05 in (128.3 mm) |
standard analog input kit STB - 0..20 mA - 2 I - 12 bits
This Zelio Logic SR3 discrete I/O extension module smart relays uses a supply voltage of 100V-240V alternating current. It has 14 inputs / outputs contact with screw-clamp terminals. It enables simple ladder programming, adapted for non-specialists.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Zelio Logic |
| Product or Component Type | Discrete I/O extension module |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number or control scheme lines | 120 ladder |
| Cycle time | 6â¦90 ms |
| Backup time | 10 years 77 °F (25 °C) |
| Clock drift | 12 min/year 32â¦131 °F (0â¦55 °C) |
| Checks | Program memory on each power up |
| [Us] rated supply voltage | 100...240 V AC |
| Supply voltage limits | 85â¦264 V |
| Supply frequency | 50/60 Hz |
| Reverse polarity protection | With |
| Discrete input number | 8 |
| Discrete input voltage | 100...240 V AC |
| Discrete input current | 0.6 mA |
| Discrete input frequency | 57...63 Hz 47...53 Hz |
| Voltage state 1 guaranteed | >= 79 V discrete input |
| Voltage state 0 guaranteed | <= 40 V discrete input |
| Current state 1 guaranteed | >= 0.17 mA discrete input) |
| Current state 0 guaranteed | <= 0.5 mA discrete input) |
| Input impedance | 350 kOhm discrete input |
| Number of Outputs | 6 relay |
| Output voltage limits | 5...30 V DC relay output) 24...250 V AC |
| Contacts type and composition | NO relay output |
| Output thermal current | 5 A for 2 outputs relay output 8 A for 4 outputs relay output |
| Electrical durability | AC-15 500000 cycles 230 V, 0.9 A relay output IEC 60947-5-1 AC-12 500000 cycles 230 V, 1.5 A relay output IEC 60947-5-1 DC-13 500000 cycles 24 V, 0.6 A relay output IEC 60947-5-1 DC-12 500000 cycles 24 V, 1.5 A relay output IEC 60947-5-1 |
| Switching capacity in mA | >= 10 mA 12 V relay output) |
| Operating rate in Hz | 0.1 Hz at Ie)relay output 10 Hz no load)relay output |
| Mechanical durability | 10000000 cycles relay output |
| [Uimp] rated impulse withstand voltage | 4 kV EN/IEC 60947-1 and EN/IEC 60664-1 |
| Response time | 50 ms ladder from state 0 to state 1)discrete input 50 ms ladder from state 1 to state 0)discrete input 50...255 ms FBD from state 0 to state 1)discrete input 50...255 ms FBD from state 1 to state 0)discrete input 10 ms from state 0 to state 1)relay output 5 ms from state 1 to state 0)relay output |
| Connections - terminals | Screw terminals, 1 x 0.25...1 x 2.5 mm² AWG 24...AWG 14) flexible with cable end Screw terminals, 2 x 0.25...2 x 0.75 mm² AWG 24...AWG 18) flexible with cable end Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) semi-solid Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) solid Screw terminals, 2 x 0.2...2 x 1.5 mm² AWG 24...AWG 16) solid |
| Tightening torque | 4.4 lbf.in (0.5 N.m) |
| Overvoltage category | III conforming to IEC 60664-1 |
| Product Weight | 0.49 lb(US) (0.22 kg) |
This product is part of the Modicon STB range, an offer of modular distributed I/O. This basic analogue input kit is an accessory kit of Programmable Logic Controllers (PLC) and Programmable Automation Controllers (PAC). It has 2 analogue inputs (current 4mA to 20mA) with 10bit resolution. This product is compatible with most major fieldbus networks. It is an analogue input kit with a rated supply voltage of 24V DC and a current consumption of 30mA at 5V DC for logic bus. The response time is 5ms. It is an IP20 rated product. Its dimensions are 128.3mm (width) x 70mm (depth) x 13.9mm (height). It is suitable for packaging, bottling, assembly, distribution, textile, printing and semiconductor machines applications. This product is certified by FM Class 1 Division 2, ATEX category 3G, CE, UL, CSA and C-Tick. This kit is suitable for use with mounting base STBXBA1000 and power distribution module STBPDT3100/3105. The kit includes STBXTS1100, 6-terminal screw type connector, STBXBA1000 base, STBXTS2100, 6-terminal spring clamp connector and STBACI1225 module. The Modicon STB distributed I/O solution is an open, modular input/output system that makes it possible to design automation islands managed by a master controller via a bus or communication network.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Modicon STB distributed I/O solution |
| Product or Component Type | Basic analog input kit |
| Kit composition | STBXTS1100, 6-terminal screw type connector STBXBA1000 base STBXTS2100, 6-terminal spring clamp connector STBACI1225 module |
| Analogue input type | Current 4...20 mA |
| Analogue input number | 2 |
| Analogue input resolution | 10 bits |
| Type of filter | Single low pass input filter 25 Hz |
Complementary
| Characteristic | Value(s) |
|---|---|
| Absolute maximum input | 25 mA/50 V DC |
| Response Time | 5 ms |
| Cold swapping | Yes |
| Hot swapping fallback | No for basic NIMs |
| Data format | EN 61131-2 IEC 61131-2 |
| Update time | 10 ms |
| Integral linearity | +/- 0.2 %FS |
| Differential linearity | Monotonic |
| Input impedance | <= 300 Ohm |
| Maximum supply current for sensors | 100 mA per input channels |
| Absolute accuracy error | +/- 0.5 % of full scale 25 °C |
| Temperature Drift | +/-0.01 %/°C |
| Insulation between channels and logic bus | 1500 V for 1 minute |
| Insulation between channels and sensor bus | 30 V |
| Addressing requirement | 2 input words |
| Product Compatibility | Mounting base STBXBA1000 Power distribution module STBPDT3100/3105 |
| [Us] rated supply voltage | 24 V DC |
| Supply | Power distribution module |
| Current consumption | 30 mA 5 V DC logic bus |
| Marking | CE |
| Overvoltage category | II |
| Status LED | 1 LED (Green) module status (RDY) |
| Depth | 2.8 in (70 mm) |
| Height | 0.5 in (13.9 mm) |
| Width | 5.05 in (128.3 mm) |
analogue I/O extension module - 4 I O - 24 V DC - for Zelio Logic
This Schneider Electric Zelio Logic SR3 Discrete I/O Extension Module Smart Relays uses a supply voltage of 12 volts direct current, has 14 inputs / outputs contact with screw-clamp terminals. This Discrete I/O Extension Module Smart Relays provides Zelio Logic relays with additional inputs and outputs. It has a compact form-factor, allowing installation on DIN rail. Simple ladder programming, adapted for non-specialists. Discovery package, coming with Zelio Soft programming software, the simplest way to learn and use this relay. Built-in EEPROM flash memory for data backup up to 10 years, easy-to-recover after a power shortage or incident. More I/O than SR2 model, for larger applications. The main application of this module is industry and building/service sector. This product is certified by C-Tick, GL, UL, CSA and GOST. It meets EN/IEC 60068-2-27 Ea, EN/IEC 61000-4-5, EN/IEC 61000-4-12 and EN/IEC 61000-4-4 L3 standards. Easy to use, Zelio Logic provides a real alternative solutions based on cabled logic or specific cards.
Main
| Characteristic | Value(s) |
|---|---|
| Range of Product | Zelio Logic |
| Product or Component Type | Discrete I/O extension module |
Complementary
| Characteristic | Value(s) |
|---|---|
| Number or control scheme lines | 120 ladder |
| Cycle time | 6â¦90 ms |
| Backup time | 10 years 77 °F (25 °C) |
| Clock drift | 12 min/year 32â¦131 °F (0â¦55 °C) |
| Checks | Program memory on each power up |
| [Us] rated supply voltage | 12 V DC |
| Supply voltage limits | 10.4â¦14.4 V |
| Reverse polarity protection | With |
| Discrete input number | 8 IEC 61131-2 Type 1 |
| Discrete input type | Resistive |
| Discrete input voltage | 12 V DC |
| Discrete input current | 4 mA |
| Counting frequency | 1 kHz discrete input |
| Voltage state 1 guaranteed | >= 7 V IB...IG used as discrete input circuit >= 5.6 V I1...IA and IH...IR discrete input circuit |
| Voltage state 0 guaranteed | <= 3 V IB...IG used as discrete input circuit <= 2.4 V I1...IA and IH...IR discrete input circuit |
| Current state 1 guaranteed | >= 2 mA I1...IA and IH...IR discrete input circuit) >= 0.5 mA IB...IG used as discrete input circuit) |
| Current state 0 guaranteed | <= 0.2 mA IB...IG used as discrete input circuit) <= 0.9 mA I1...IA and IH...IR discrete input circuit) |
| Input compatibility | 3-wire proximity sensors PNP discrete input |
| Input impedance | 14 kOhm IB...IG used as discrete input circuit 2.7 kOhm I1...IA and IH...IR discrete input circuit |
| Number of Outputs | 6 relay |
| Output voltage limits | 24...250 V AC relay output) 5...30 V DC relay output) |
| Contacts type and composition | NO relay output |
| Output thermal current | 5 A for 2 outputs relay output 8 A for 4 outputs relay output |
| Electrical durability | AC-15 500000 cycles 230 V, 0.9 A relay output IEC 60947-5-1 AC-12 500000 cycles 230 V, 1.5 A relay output IEC 60947-5-1 DC-13 500000 cycles 24 V, 0.6 A relay output IEC 60947-5-1 DC-12 500000 cycles 24 V, 1.5 A relay output IEC 60947-5-1 |
| Switching capacity in mA | >= 10 mA 12 V relay output) |
| Operating rate in Hz | 0.1 Hz at Ie)relay output 10 Hz no load)relay output |
| Mechanical durability | 10000000 cycles relay output |
| [Uimp] rated impulse withstand voltage | 4 kV EN/IEC 60947-1 and EN/IEC 60664-1 |
| Response time | 10 ms from state 0 to state 1)relay output 5 ms from state 1 to state 0)relay output |
| Connections - terminals | Screw terminals, 1 x 0.25...1 x 2.5 mm² AWG 24...AWG 14) flexible with cable end Screw terminals, 2 x 0.25...2 x 0.75 mm² AWG 24...AWG 18) flexible with cable end Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) semi-solid Screw terminals, 1 x 0.2...1 x 2.5 mm² AWG 25...AWG 14) solid Screw terminals, 2 x 0.2...2 x 1.5 mm² AWG 24...AWG 16) solid |
| Tightening torque | 4.4 lbf.in (0.5 N.m) |
| Overvoltage category | III conforming to IEC 60664-1 |
| Product Weight | 0.49 lb(US) (0.22 kg) |
Main category name:Modules Sub category name:Modules Vendor:Schneider