Drives - Motors - Circuits Protection

973 products

Showing 961 - 973 of 973 products

Showing 961 - 973 of 973 products
View
ATV31H055N4 Schneider
Schneider ATV31H055N4 Schneider
€1.155,95
Only 5 units left

variable speed drive - ATV31 - 0.55kW - 380..500V - 3-phase supply - EMC filter - IP20
ATV31H018M3X Schneider
Schneider ATV31H018M3X Schneider
€0,00
Sold Out

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Without EMC filter
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 0.18 kW 4 kHz
Maximum Horse Power Rating 0.25 hp 4 kHz
Line current 1.9 A 240 V
2.1 A 200 V, Isc = 1 kA
Apparent power 0.7 kVA
Prospective line Isc 1 kA
Nominal output current 1.5 A 4 kHz
Maximum transient current 2.3 A 60 s
Power dissipation in W 23 W at nominal load
Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Automatic whatever the load
Adjustable
Suppressable
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s
S, U or customized
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 2.9 lb(US) (1.3 kg)
ATV31H055M2 Schneider
Schneider ATV31H055M2 Schneider
€755,95
Only 3 units left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Integrated
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase Single phase
Motor power kW 0.55 kW 4 kHz
Maximum Horse Power Rating 0.75 hp 4 kHz
Line current 5.8 A 240 V
6.8 A 200 V, Isc = 1 kA
Apparent power 1.4 kVA
Prospective line Isc 1 kA
Nominal output current 3.7 A 4 kHz
Maximum transient current 5.6 A 60 s
Power dissipation in W 46 W at nominal load
Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Automatic whatever the load
Suppressable
Adjustable
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 3.3 lb(US) (1.5 kg)
ATV31H037M2 Schneider
Schneider ATV31H037M2 Schneider
€910,95
Only 6 units left

variable speed drive - ATV31 - 0.37kW - 200..240V - 1-phase supply - EMC filter - IP20
ATV31CU22M2 Schneider
Schneider ATV31CU22M2 Schneider
€2.920,95
Only 2 units left

Main

Characteristic Value(s)
Range of Product Altivar 31
Product or Component Type Variable speed drive
Product destination Asynchronous motors
Product Specific Application Simple machine
Assembly style Enclosed
Component name ATV31
EMC filter Integrated
power supply voltage 200...240 V - 15...10 %
power supply frequency 50...60 Hz - 5...5 %
Phase Single phase
Motor power kW 2.2 kW
Maximum Horse Power Rating 3 hp
Line current 18.4 A 240 V 1 kA
21.9 A 200 V 1 kA
Apparent power 4.4 kVA
maximum prospective line Isc 1 kA
Nominal output current 11 A 4 kHz
Maximum transient current 16.5 A 60 s
Power dissipation in W 123 W at nominal load
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 3
IP degree of protection IP55

Complementary

Characteristic Value(s)
power supply voltage limit 170…264 V
power supply frequency limits 47.5…63 Hz
Speed drive output frequency 0.5…500 Hz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
30 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Automatic whatever the load
Adjustable
Suppressable
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19…30 V, <100 mA overload protection
Internal supply for logic inputs 19…30 V, <100 mA short-circuit protection
Internal supply for reference potentiometer 10…10.8 V, <10 mA overload protection
Internal supply for reference potentiometer 10…10.8 V, <10 mA short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
input sampling time LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
output response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current 10 mA 5 V DC R1-R2
Maximum switching current 2 A 250 V AC inductive - cos phi = 0.4 - L/R = 7 ms R1-R2)
2 A 30 V DC inductive - cos phi = 0.4 - L/R = 7 ms R1-R2)
5 A 250 V AC resistive - cos phi = 1 - L/R = 0 ms R1-R2)
5 A 30 V DC resistive - cos phi = 1 - L/R = 0 ms R1-R2)
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s
S, U or customized
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Local signalling 1 LED (red) for drive voltage
Four 7-segment display units for CANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Communication Port Protocol CANopen
Modbus
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link Modbus
Transmission frame RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 23.6 lb(US) (10.7 kg)
ATV31H075M3XA Schneider
Schneider ATV31H075M3XA Schneider
€448,95
Only 1 unit left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
Variant With drive order potentiometer
EMC filter Without EMC filter
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 0.75 kW 4 kHz
Maximum Horse Power Rating 1 hp 4 kHz
Line current 5.6 A 240 V
6.4 A 200 V, Isc = 1 kA
Apparent power 2.2 kVA
Prospective line Isc 1 kA
Nominal output current 4.8 A 4 kHz
Maximum transient current 7.2 A 60 s
Power dissipation in W 55 W at nominal load
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 4

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Suppressable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
AIP potentiometer reference 8 ms 10 bits +/- 4.3 % +/- 0.2 %
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 2.9 lb(US) (1.3 kg)
ATV31H075S6X Schneider
Schneider ATV31H075S6X Schneider
€779,95
Only 2 units left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Without EMC filter
[Us] rated supply voltage 525...600 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 0.75 kW 4 kHz
Maximum Horse Power Rating 1 hp 4 kHz
Line current 2.4 A 600 V
2.8 A 525 V, Isc = 1 kA
Apparent power 2.5 kVA
Prospective line Isc 1 kA
Nominal output current 1.7 A 4 kHz
Maximum transient current 2.6 A 60 s
Power dissipation in W 36 W at nominal load
Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 446.25…660 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Suppressable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 3.7 lb(US) (1.7 kg)
ATV31H037N4 Schneider
Schneider ATV31H037N4 Schneider
€686,95
Only 3 units left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Integrated
[Us] rated supply voltage 380...500 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 0.37 kW 4 kHz
Maximum Horse Power Rating 0.5 hp 4 kHz
Line current 1.7 A 500 V
2.2 A 380 V, Isc = 1 kA
Apparent power 1.5 kVA
Prospective line Isc 1 kA
Nominal output current 1.5 A 4 kHz
Maximum transient current 2.3 A 60 s
Power dissipation in W 32 W at nominal load
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 323…550 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Suppressable
Automatic whatever the load
Adjustable
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 4.0 lb(US) (1.8 kg)
ATV31HD11S6X Schneider
Schneider ATV31HD11S6X Schneider
€0,00
Sold Out

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Without EMC filter
[Us] rated supply voltage 525...600 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 11 kW 4 kHz
Maximum Horse Power Rating 15 hp 4 kHz
Line current 24.4 A 600 V
27.8 A 525 V, Isc = 1 kA
Apparent power 25 kVA
Prospective line Isc 1 kA
Nominal output current 17 A 4 kHz
Maximum transient current 25.5 A 60 s
Power dissipation in W 257 W at nominal load
Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 446.25…660 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Automatic whatever the load
Adjustable
Suppressable
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 22.05 lb(US) (10 kg)
ATV31H075M3X Schneider
Schneider ATV31H075M3X Schneider
€650,95
Only 1 unit left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Without EMC filter
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 0.75 kW 4 kHz
Maximum Horse Power Rating 1 hp 4 kHz
Line current 5.6 A 240 V
6.4 A 200 V, Isc = 1 kA
Apparent power 2.2 kVA
Prospective line Isc 1 kA
Nominal output current 4.8 A 4 kHz
Maximum transient current 7.2 A 60 s
Power dissipation in W 55 W at nominal load
Asynchronous motor control profile Sensorless flux vector control with PWM type motor control signal
Factory set : constant torque
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Suppressable
Adjustable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps Linear adjustable separately from 0.1 to 999.9 s
S, U or customized
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 2.9 lb(US) (1.3 kg)
ATV31HD15M3X Schneider
Schneider ATV31HD15M3X Schneider
€0,00
Sold Out

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Without EMC filter
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 15 kW 4 kHz
Maximum Horse Power Rating 20 hp 4 kHz
Line current 71.9 A 240 V
82.1 A 200 V, Isc = 1 kA
Apparent power 28.5 kVA
Prospective line Isc 1 kA
Nominal output current 66 A 4 kHz
Maximum transient current 99 A 60 s
Power dissipation in W 628 W at nominal load
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Suppressable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Outer dimension 330 x 245 x 190 mm
Product Weight 23.1 lb(US) (10.5 kg)
ATV31HD11N4 Schneider
Schneider ATV31HD11N4 Schneider
€1.523,95
Only 1 unit left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Integrated
[Us] rated supply voltage 380...500 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase 3 phase
Motor power kW 11 kW 4 kHz
Maximum Horse Power Rating 15 hp 4 kHz
Line current 28.4 A 500 V
37.2 A 380 V, Isc = 1 kA
Apparent power 25 kVA
Prospective line Isc 1 kA
Nominal output current 27.7 A 4 kHz
Maximum transient current 41.6 A 60 s
Power dissipation in W 397 W at nominal load
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 323…550 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Suppressable
Adjustable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Outer dimension 390 x 245 x 190 mm
555 x 234 x 268 mm
405 x 234 x 268 mm
330 x 245 x 190 mm
Product Weight 24.3 lb(US) (11 kg)
ATV31HU11M2 Schneider
Schneider ATV31HU11M2 Schneider
€505,95
Only 4 units left

Main

Characteristic Value(s)
Range of Product Altivar
Product or Component Type Variable speed drive
Product Specific Application Simple machine
Component name ATV31
Assembly style With heat sink
EMC filter Integrated
[Us] rated supply voltage 200...240 V - 5...5 %
Supply frequency 50...60 Hz - 5...5 %
Phase Single phase
Motor power kW 1.1 kW 4 kHz
Maximum Horse Power Rating 1.5 hp 4 kHz
Line current 10.2 A 240 V
12.1 A 200 V, Isc = 1 kA
Apparent power 2.4 kVA
Prospective line Isc 1 kA
Nominal output current 6.9 A 4 kHz
Maximum transient current 10.4 A 60 s
Power dissipation in W 74 W at nominal load
Asynchronous motor control profile Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal
Analogue input number 3

Complementary

Characteristic Value(s)
Product destination Asynchronous motors
Supply voltage limits 170…264 V
Network Frequency 47.5...63 Hz
Output frequency 0.0005…0.5 kHz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
Speed range 1…50
Transient overtorque 150…170 % of nominal motor torque
Braking torque <= 150 % 60 s with braking resistor
100 % with braking resistor continuously
150 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Adjustable
Suppressable
Automatic whatever the load
Output voltage <= power supply voltage
Electrical connection Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 0.004 in² (2.5 mm²) AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 0.004 in² (2.5 mm²) AWG 14
Tightening torque Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 5.3 lbf.in (0.6 N.m)
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- 7.08 lbf.in (0.8 N.m)
Insulation Electrical between power and control
Supply Internal supply for logic inputs 19...30 V 100 mA overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) 10...10.8 V 10 mA overload and short-circuit protection
Analogue input type AI3 configurable current 0...20 mA 250 Ohm
AI1 configurable voltage 0...10 V 30 V max 30000 Ohm
AI2 configurable voltage +/- 10 V 30 V max 30000 Ohm
Sampling duration LI1...LI6 4 ms discrete
AI1, AI2, AI3 8 ms analog
Response time AOV, AOC 8 ms analog
R1A, R1B, R1C, R2A, R2B 8 ms discrete
Linearity error +/- 0.2 % output
Analogue output number 2
Analogue output type AOC configurable current 0...20 mA 800 Ohm 8 bits
AOV configurable voltage 0...10 V 470 Ohm 8 bits
Discrete input logic Positive logic (source) LI1...LI6), < 5 V, > 11 V
Logic input not wired LI1...LI4), < 13 V
Negative logic (source) LI1...LI6), > 19 V
Discrete output number 2
Discrete output type Configurable relay logic R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles
Configurable relay logic R2A, R2B) NC - 100000 cycles
Minimum switching current R1-R2 10 mA 5 V DC
Maximum switching current R1-R2 2 A 250 V AC inductive, cos phi = 0.4 7 ms
R1-R2 2 A 30 V DC inductive, cos phi = 0.4 7 ms
R1-R2 5 A 250 V AC resistive, cos phi = 1 0 ms
R1-R2 5 A 30 V DC resistive, cos phi = 1 0 ms
Discrete input number 6
Discrete input type LI1...LI6) programmable 24 V, 0…100 mA PLC 3500 Ohm
Acceleration and deceleration ramps S, U or customized
Linear adjustable separately from 0.1 to 999.9 s
Braking to standstill By DC injection
Protection type Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor
Insulation resistance >= 500 mOhm 500 V DC for 1 minute
Display type 1 LED Red)drive voltage
Four 7-segment display unitsCANopen bus status
Time constant 5 ms for reference change
Frequency resolution Display unit 0.1 Hz
Analog input 0.1...100 Hz
Connector type 1 RJ45 CANopen via VW3 CANTAP2 adaptor
1 RJ45 Modbus
Physical interface RS485 multidrop serial link CANopen via VW3 CANTAP2 adaptor
RS485 multidrop serial link Modbus
Transmission frame RTU CANopen via VW3 CANTAP2 adaptor
RTU Modbus
Transmission Rate 10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen via VW3 CANTAP2 adaptor
4800, 9600 or 19200 bps Modbus
Number of addresses 1…127 CANopen via VW3 CANTAP2 adaptor
1…247 Modbus
Number of drive 127 CANopen via VW3 CANTAP2 adaptor
31 Modbus
Marking CE
Operating position Vertical +/- 10 degree
Product Weight 4.0 lb(US) (1.8 kg)

Recently viewed