2CDH781001R0352 ABB - S751DR-E35
ABB

2CDH781001R0352 ABB - S751DR-E35

ABB EcoSolutions

ABB EcoSolutions:
No
Recyclability Rate of the Product acc. to EN45555:
Design for Closing Resource Loops - Standard EN45555 - 45.9 %
ABB Site Meeting Group Waste To Landfill Target:
No non-hazardous waste is sent to a landfill
Extended Product Lifetime:
Product Durability
End Of Life Disassembling Instructions:
Environmental Product Declaration - EPD:

Technical

Function:
Single Pole Switching
Suitable for Isolation:
Yes
Dielectric Test Voltage:
50 / 60 Hz - 1 min 2 kV
Power Supply Connection:
Arbitrary
Contact Position Indication:
Red ON / Green OFF
Number of Poles:
1P
Tightening Torque:
2.5 ... 3 N·m
Screw Terminal Type:
Cable Clamp
Actuator Marking:
I / O
Recommended Screw Driver:
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Accessories Available:
Yes
Connecting Capacity:
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Installation Size:
acc. to DIN 43880 3
Terminal Type:
Screw Terminals

Electrical

Tripping Characteristic:
E (Selective)
Rated Operational Voltage:
230 / 400 V AC
Rated Insulation Voltage (Ui):
acc. to IEC/EN 60664-1 690 V
Rated Impulse Withstand Voltage (Uimp):
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
Input Voltage Type:
AC
Rated Current (In):
35 A
Rated Short-Circuit Capacity:
(230 / 400 V AC) 25 kA
Rated Frequency (f):
50 / 60 Hz
Power Loss:
at Rated Operating Conditions per Pole 6.3 W
Overvoltage Category:
IV
I²t Characteristic:

Technical UL/CSA

Connecting Capacity UL/CSA:
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG

Material Compliance

RoHS Status:
Following EU Directive 2011/65/EU and Amendment 2015/863 July 22, 2019
RoHS Date:
20160607
REACH Information:
False - does not contain substances > 0.1 mass percentage
REACH Date:
20240821
Conflict Minerals Reporting Template (CMRT):
WEEE Category:
5. Small Equipment (No External Dimension More Than 50 cm)
WEEE B2C / B2B:
Business To Business

Environmental

Ambient Air Temperature:
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Degree of Protection:
IP20
Enclosure with Cover IP40
IP20
Enclosure with Cover IP40
Pollution Degree:
3
Environmental Conditions:
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
Resistance to Vibrations:
20 Cycles with Load 0.8 In: 2g 5 ... 150 ... 5 Hz
Resistance to Shock acc. to IEC 60068-2-27:
30g 3 shocks 11 ms

Dimensions

Product Net Width:
27 mm
Product Net Height:
130 mm
Product Net Depth / Length:
92 mm
Product Net Weight:
0.35 kg
Pole Net Weight:
0.35 kg

Engineering

EPLAN Data:

Ordering

Package Level 1 Units:
carton 3 piece
Package Level 1 Gross Weight:
1.15 kg
E-Number (Norway):
1634333

Certificates and Declarations

Declaration of Conformity - CE:

Installation

Instructions and Manuals:
Mounting Type:
DIN-Rail
Mounting on DIN Rail:
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
Mounting Position:
1 ... 6
any
1 ... 6
any

Popular Downloads

Data Sheet, Technical Information (Part 2):
I²t Characteristic:
Time-Current Characteristic Curve:

External Classifications and Standards

ETIM 9:
EC001047 - Selective main line circuit breaker
ETIM 10:
EC001047 - Selective main line circuit breaker
UNSPSC:
39121614
eClass:
V11.0 : 27141903
Object Classification Code:
F
Standards:
DIN VDE 0641-21
Certification Agency:
DIN
Standardization Body:
DIN
Description
Warranty
Shipping and Return

ABB EcoSolutions

ABB EcoSolutions:
No
Recyclability Rate of the Product acc. to EN45555:
Design for Closing Resource Loops - Standard EN45555 - 45.9 %
ABB Site Meeting Group Waste To Landfill Target:
No non-hazardous waste is sent to a landfill
Extended Product Lifetime:
Product Durability
End Of Life Disassembling Instructions:
Environmental Product Declaration - EPD:

Technical

Function:
Single Pole Switching
Suitable for Isolation:
Yes
Dielectric Test Voltage:
50 / 60 Hz - 1 min 2 kV
Power Supply Connection:
Arbitrary
Contact Position Indication:
Red ON / Green OFF
Number of Poles:
1P
Tightening Torque:
2.5 ... 3 N·m
Screw Terminal Type:
Cable Clamp
Actuator Marking:
I / O
Recommended Screw Driver:
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Accessories Available:
Yes
Connecting Capacity:
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Installation Size:
acc. to DIN 43880 3
Terminal Type:
Screw Terminals

Electrical

Tripping Characteristic:
E (Selective)
Rated Operational Voltage:
230 / 400 V AC
Rated Insulation Voltage (Ui):
acc. to IEC/EN 60664-1 690 V
Rated Impulse Withstand Voltage (Uimp):
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
Input Voltage Type:
AC
Rated Current (In):
35 A
Rated Short-Circuit Capacity:
(230 / 400 V AC) 25 kA
Rated Frequency (f):
50 / 60 Hz
Power Loss:
at Rated Operating Conditions per Pole 6.3 W
Overvoltage Category:
IV
I²t Characteristic:

Technical UL/CSA

Connecting Capacity UL/CSA:
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG

Material Compliance

RoHS Status:
Following EU Directive 2011/65/EU and Amendment 2015/863 July 22, 2019
RoHS Date:
20160607
REACH Information:
False - does not contain substances > 0.1 mass percentage
REACH Date:
20240821
Conflict Minerals Reporting Template (CMRT):
WEEE Category:
5. Small Equipment (No External Dimension More Than 50 cm)
WEEE B2C / B2B:
Business To Business

Environmental

Ambient Air Temperature:
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Degree of Protection:
IP20
Enclosure with Cover IP40
IP20
Enclosure with Cover IP40
Pollution Degree:
3
Environmental Conditions:
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
Resistance to Vibrations:
20 Cycles with Load 0.8 In: 2g 5 ... 150 ... 5 Hz
Resistance to Shock acc. to IEC 60068-2-27:
30g 3 shocks 11 ms

Dimensions

Product Net Width:
27 mm
Product Net Height:
130 mm
Product Net Depth / Length:
92 mm
Product Net Weight:
0.35 kg
Pole Net Weight:
0.35 kg

Engineering

EPLAN Data:

Ordering

Package Level 1 Units:
carton 3 piece
Package Level 1 Gross Weight:
1.15 kg
E-Number (Norway):
1634333

Certificates and Declarations

Declaration of Conformity - CE:

Installation

Instructions and Manuals:
Mounting Type:
DIN-Rail
Mounting on DIN Rail:
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
Mounting Position:
1 ... 6
any
1 ... 6
any

Popular Downloads

Data Sheet, Technical Information (Part 2):
I²t Characteristic:
Time-Current Characteristic Curve:

External Classifications and Standards

ETIM 9:
EC001047 - Selective main line circuit breaker
ETIM 10:
EC001047 - Selective main line circuit breaker
UNSPSC:
39121614
eClass:
V11.0 : 27141903
Object Classification Code:
F
Standards:
DIN VDE 0641-21
Certification Agency:
DIN
Standardization Body:
DIN

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Price on request
Ask for quote
   
Notify Me When Available
Description
Warranty
Shipping and Return

ABB EcoSolutions

ABB EcoSolutions:
No
Recyclability Rate of the Product acc. to EN45555:
Design for Closing Resource Loops - Standard EN45555 - 45.9 %
ABB Site Meeting Group Waste To Landfill Target:
No non-hazardous waste is sent to a landfill
Extended Product Lifetime:
Product Durability
End Of Life Disassembling Instructions:
Environmental Product Declaration - EPD:

Technical

Function:
Single Pole Switching
Suitable for Isolation:
Yes
Dielectric Test Voltage:
50 / 60 Hz - 1 min 2 kV
Power Supply Connection:
Arbitrary
Contact Position Indication:
Red ON / Green OFF
Number of Poles:
1P
Tightening Torque:
2.5 ... 3 N·m
Screw Terminal Type:
Cable Clamp
Actuator Marking:
I / O
Recommended Screw Driver:
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Cross Recess Pozidriv 2
Slotted 1 x 5.5
Accessories Available:
Yes
Connecting Capacity:
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Flexible with Ferrule 2.5 ... 50 mm²
Flexible 2x 0.5 ... 1.5 mm²
Flexible 2.5 ... 50 mm²
Rigid 2x 0.5 ... 1.5 mm²
Rigid 2.5 ... 50 mm²
Stranded 2.5 ... 50 mm²
Installation Size:
acc. to DIN 43880 3
Terminal Type:
Screw Terminals

Electrical

Tripping Characteristic:
E (Selective)
Rated Operational Voltage:
230 / 400 V AC
Rated Insulation Voltage (Ui):
acc. to IEC/EN 60664-1 690 V
Rated Impulse Withstand Voltage (Uimp):
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
6 kV
at 2000 m 8 kV
at Sea Level 9.8 kV
Input Voltage Type:
AC
Rated Current (In):
35 A
Rated Short-Circuit Capacity:
(230 / 400 V AC) 25 kA
Rated Frequency (f):
50 / 60 Hz
Power Loss:
at Rated Operating Conditions per Pole 6.3 W
Overvoltage Category:
IV
I²t Characteristic:

Technical UL/CSA

Connecting Capacity UL/CSA:
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG
Flexible 2x 18-16 AWG
Rigid 2x 20-16 AWG

Material Compliance

RoHS Status:
Following EU Directive 2011/65/EU and Amendment 2015/863 July 22, 2019
RoHS Date:
20160607
REACH Information:
False - does not contain substances > 0.1 mass percentage
REACH Date:
20240821
Conflict Minerals Reporting Template (CMRT):
WEEE Category:
5. Small Equipment (No External Dimension More Than 50 cm)
WEEE B2C / B2B:
Business To Business

Environmental

Ambient Air Temperature:
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Operation -25 ... +55 °C
Storage -40 ... +70 °C
Degree of Protection:
IP20
Enclosure with Cover IP40
IP20
Enclosure with Cover IP40
Pollution Degree:
3
Environmental Conditions:
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
28 cycles
with 55 °C / 90-96 %
and 25 °C / 95-100 %
Resistance to Vibrations:
20 Cycles with Load 0.8 In: 2g 5 ... 150 ... 5 Hz
Resistance to Shock acc. to IEC 60068-2-27:
30g 3 shocks 11 ms

Dimensions

Product Net Width:
27 mm
Product Net Height:
130 mm
Product Net Depth / Length:
92 mm
Product Net Weight:
0.35 kg
Pole Net Weight:
0.35 kg

Engineering

EPLAN Data:

Ordering

Package Level 1 Units:
carton 3 piece
Package Level 1 Gross Weight:
1.15 kg
E-Number (Norway):
1634333

Certificates and Declarations

Declaration of Conformity - CE:

Installation

Instructions and Manuals:
Mounting Type:
DIN-Rail
Mounting on DIN Rail:
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
TH35-15 (35 x 15 mm Mounting Rail) acc. to IEC 60715
TH35-7.5 (35 x 7.5 mm Mounting Rail) acc. to IEC 60715
Mounting Position:
1 ... 6
any
1 ... 6
any

Popular Downloads

Data Sheet, Technical Information (Part 2):
I²t Characteristic:
Time-Current Characteristic Curve:

External Classifications and Standards

ETIM 9:
EC001047 - Selective main line circuit breaker
ETIM 10:
EC001047 - Selective main line circuit breaker
UNSPSC:
39121614
eClass:
V11.0 : 27141903
Object Classification Code:
F
Standards:
DIN VDE 0641-21
Certification Agency:
DIN
Standardization Body:
DIN

All PLC Direct products come with a 1-year warranty. The warranty is issued by PLC Direct. Warranty coverage commences at the date of purchase. The warranty is for mechanical defects or failures not caused by human factors including but not limited to (a) incorrect installation, (b) operating the unit in sub-optimal conditions or in scenarios not recommended by the manufacturer, (c) poor unit maintenance, etc. The warranty does not cover programming or software related issues.

If the product is eligible for PLC Direct’s warranty coverage and the customer encounters an issue with the product, we will request the item is shipped to us for diagnosis and examination. Regardless of the cause of product issues, the customer will bear responsibility for the cost of shipping the unit to PLC Direct for evaluation. Where the unit was damaged by human factors, we will offer a repair or replace quote; in cases where damage was caused by human factors, the customer is responsible for the cost of shipping the repaired/replaced unit from PLC Direct to the customer. Where the unit was not damaged by human factors but is covered by PLC Direct’s warranty, we will repair or replace the unit at our cost (or, in rare cases, refund you your purchase); in such cases, PLC Direct will bear the cost of shipping the repaired or replaced product back to the customer. It is up to PLC Direct’s discretion whether to repair, replace, or refund the customer in such cases. Diagnoses can take time to complete based on technician availability and the complexity of diagnosis.

In no event shall PLC Direct be liable for any damages except actual damages up to, but not exceeding, the amount paid to us for the product, including we shall not be liable for any consequential or indirect damages or lost profits whether or not advised of same.

PLC Direct offers free shipping worldwide. Product ship from a various warehouses worldwide based on the customer's and the product's location. The estimated delivery date on the product page is PLC Direct's best estimated assuming a US-based shipping destination.

Regardless of where the product is shipping from, PLC Direct covers all duties for US-based shipping destinations. For non-US-based shipping destinations, customers are responsible for duties as appropriate.

PLC Direct's focus is on balancing price with lead time. Some but not all products can be expedited. If you have questions about delivery ETAs, please contact our team.

Trusted By

"Fast service for obsolete parts"

Increasingly PLC/ HMI control platforms are becoming obsolete and parts are no longer supported, however PLC Direct had the HMI we needed and fast shipping for our system to get back online!

Buyer at GE Health

"Helping us move projects forward"

With supply chain issues increasingly affecting our business, PLC Direct has been there for us to supply the PLC products we need, when we need it. If they don't have it readily available, they find it and provide it quickly and reliably. This has helped us move forward with several projects that would have otherwise taken us many, many months to complete.

Buyer at E-Merge Systems – A Rockwell Integrator

You may also like

Recently viewed