Drive Control unit+cables RDCU-12C+cables. ACS800-04M-0550-5+E202+E208+H360+J400+K458+P901+P916+P920+OR715
4 inputs for resistance temperature measurement For PT100 and PT1000 Configurable sensor type per channel Direct resistance measurement Configurable 2- or 3- wire connections per module Configurable filter time The module is equipped with 4 inputs for PT100/PT1000 resistance temperature measurement.
6 digital outputs Relay module for 115 VAC 6 normally open contacts Single-channel isolated outputs The module is equipped with 6 relay outputs with normally open contacts for 115 VAC. The outputs are single-channel isolated.
2 digital outputs Relay module for 240 VAC / 30 VDC 2 change over contacts Single-channel isolated outputs The module is equipped with 2 relay outputs with changeover contacts for 240 VAC / 30 VDC. The outputs are single-channel isolated.
POWERLINK I/O configuration and firmware update via the fieldbus Integrated hub for economical wiring The bus controller makes it possible to connect X2X Link I/O nodes to POWERLINK. It is also possible to operate the X2X Link cycle synchronously 1:1 or synchronous to POWERLINK using a prescaler. POWERLINK is a standard protocol for Fast Ethernet equipped with hard real-time characteristics. The POWERLINK Standardization Group (EPSG) ensures that the standard remains open and is continually developed:: www.ethernet-powerlink.org.
POWERLINK I/O configuration and firmware update via the fieldbus Integrated hub for efficient cabling Up to 2 slots for interface modules The bus controller makes it possible to connect X2X Link I/O nodes to POWERLINK. It is also possible to operate the X2X Link cycle synchronously 1:1 or synchronous to POWERLINK using a prescaler. POWERLINK is a standard protocol for Fast Ethernet equipped with hard real-time characteristics. The POWERLINK Standardization Group (EPSG) ensures that the standard remains open and is continually developed:: www.ethernet-powerlink.org. The bus modules expanded to the left allow connection of up to 2 interface modules in addition to the bus controller.
12 digital inputs Sink connection 1-wire connections Software input filter can be configured for entire module The module is equipped with 12 inputs for 1-wire connections. The module is designed for sink input wiring.
Bus base The following modules are used on the bus module: Base module (BC, HB, etc.) Supply module The left and right end cover plates are included in delivery.
CAN bus connection Integrated terminating resistor The interface module can be used to expand the X20 CPU for specific applications. It is equipped with a CAN bus interface.
2 safe digital inputs, sink circuit 2 pulse outputs Software input filter configurable for each channel 2 safe relay outputs Output type "Relay" Relay module for 48 VAC / 24 VDC Switching current 6 A Normally open contact Single-channel isolated outputs The module is equipped with 2 safe digital inputs and 2 safe relay outputs. It is designed for a nominal voltage of 24 VDC. The module can be used to read digital signals and for floating control of actuators in safety-related applications up to PL e or SIL 3. The module is equipped with filters that are individually configurable for switch-on and switch-off behavior. The module also provides pulse signals for diagnosing the sensor line. Safety relays are installed in the module. The positively driven feedback contacts are evaluated internally by the module. Safe digital output channels provide protection against automatic restart when network errors occur. This module is designed for X20 12-pin terminal blocks.
20 safe digital inputs 4 pulse outputs Sink circuit Software input filter configurable for each channel This module is equipped with 20 safe digital inputs. It is designed for a nominal voltage of 24 VDC. The module can be used to read various digital signals in safety-related applications up to PL e or SIL 3. The module is equipped with filters that are individually configurable for switch-on and switch-off behavior. The module also provides pulse signals for diagnosing the sensor line. This module is designed for X20 12-pin terminal blocks.
2 analog outputs Either current or voltage signal possible 13-bit digital converter resolution The module is equipped with 2 outputs with 13-bit (including sign) digital converter resolution. It is possible to select between the current and voltage signal using different terminals. This module is designed for X20 6-pin terminal blocks. If needed (e.g. for logistical reasons), the 12-pin terminal block can also be used.
16 digital outputs Source connection 1-wire connections Integrated output protection The module is equipped with 16 outputs for 1-wire connections. The module is designed for source output wiring.
16 digital inputs Sink connection 1-wire connections Software input filter can be configured for entire module The module is equipped with 16 inputs for 1-wire connections. The module is designed for sink input wiring.
Tool-free wiring with push-in technology Simple wire release using a screwdriver Ability to label each terminal Plain text labeling also possible Test access for standard probes Can be customer-coded X20 24 VDC modules with 16 connections are wired using the X20TB1F terminal block.
Tool-free wiring with push-in technology Simple wire release using lever Ability to label each terminal Plain text labeling also possible Test access for standard probes Can be customer-coded The X20 24 VDC modules are wired using the X20TB06 and X20TB12 terminal blocks.
Supply for the bus controller, X2X Link and internal I/O supply Feed and bus controller / X2X Link supply electrically isolated Redundancy of bus controller / X2X Link supply possible by operating multiple supply modules simultaneously Service interface (RS232) The supply module is used together with an X20 bus controller. It is equipped with a feed for the bus controller, the X2X Link and the internal I/O supply.
Intel Atom 1.6 GHz processor with an additional I/O processor Onboard Ethernet, POWERLINK with poll response chaining and USB 1 slot for modular interface expansion CompactFlash as removable application memory 512 MB DDR2 SDRAM Fanless The X20CP1586 is a powerful controller for the X20 system. This controller is especially useful for applications that require short cycle times, have to process very large amounts of data or carry out floating point operations. It is clocked at 1.6 GHz and equipped with 512 MB DDR2 SDRAM. USB, Ethernet, POWERLINK and removable CompactFlash are all included as standard features. The standard Ethernet interface is capable of handling communication in the gigabit range. For even more real-time network performance, the onboard POWERLINK interface supports poll response chaining mode (PRC). The controller is equipped with one slot available for X20 communication modules. Various bus and network systems can easily be integrated into the X20 system through the use of communication modules.
Intel Celeron 650 Performance with additional I/O processor Ethernet, POWERLINK and USB onboard 1 slot for modular interface expansion CompactFlash as removable application memory Fan can be exchanged from the outside, tool-free Extremely compact The X20CP1486 is a high-performance CPU for the X20 System. This CPU can be used anywhere from high-end applications in machine manufacturing to demanding tasks in process control. Ethernet and USB are onboard. In addition, the CPU has a POWERLINK connection for real-time communication. The only differences from the X20CP3486 are that the X20CP1486 only has one slot for interface modules and a smaller width.
Basis for all power supply modules For creating potential groups The internal I/O power supply is interrupted to the left. The bus module is the base for all power supply modules.
6 inputs for thermocouples For sensor types J, K, N, S, B, R Additional direct raw value measurement Integrated terminal temperature compensation Configurable filter time The module is equipped with 6 inputs for J, K, N, S, B and R thermocouple sensors. The module has an integrated terminal temperature compensation.